Search Documents

By Donald J. Westmaas, Fred C. Drury

The factors affecting the selection and use of exploisves have changed radically in the past three decades. The objective of this paper is to point out considerations which should now be employed by the Explosives Engineer in his selection and use of modern chemical explosives.

Jan 1, 1978

By Leslie C. Taylor, Anthony L. Kee

Computational modeling of explosively loaded saturated sand on a suspended plate is an inherently complex problem. In this study a computational method is used to predict the dynamic pressure load/impulse from a buried charge. A fully coupled code modeling the explosive charge, sand and air with a Eulerian mesh and the plate structure with Lagrange elements, such as Gemini-Dyna, is an appropriate computational tool. In water-saturated sand, the loadings are soil and water-transmitted shock and bubble or blast effects depending on the depth and the charge size. The computations provide the capability to determine the total impulse load placed on a horizontal plate on or above the soil due to an explosion in the saturated sand for different burial depths in saturated sand and different plate stand off distances. The following test case will be presented: (a) 4.5 Kg (10 lbs) TNT, 10.16 cm (4 in) depth of burial to top of charge, and 20.32 cm (8 inch) stand off distance (Test 4).

Jan 1, 2005

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By R C. Sittig

The manufacture of commerical detonating cord by the "wet process" technique is discussed. Raw material variability as a potential source of production problems is examined. Comparison to the "dry process" method is made. Inert samples, illustrating the cord's construction at various points in the production process, were distributed.

Jan 1, 1976

By Julia Creasey, Natalie Hodgson, Claire Ward, Craig Davies, Helen Sarginson

"Emulsion explosive producers are attempting to lower the cost of emulsion production by using lowquality ammonium nitrate in emulsion formulations. Low quality ammonium nitrate contains additivessuch as anti-caking agents and crystal modifiers which contaminate the emulsions causing instability. This presents a need for an effective emulsifier that will maintain emulsion stability under thesechallenging conditions."

Jan 1, 2017

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991

By Ronald Ticona

Generally, the drilling and blasting operation are managed independently to the processing plant outcomes. Therefore, the technical segmentation to determinate the ore drill and blast designs do not include processing plant rock properties such as Bond Work Index, Axb, Drop Weight Index or other. This work describes the case study of a copper mine in Peru, which, together with its strategic partner ORICA, have implemented projects focused on optimizing mine fragmentation. The year 2021, mine operation according to its mine plan would have a significantly increased SAG mill hardness, which would impact directly on copper concentrated production. An integrated strategy from mine to plant has become necessary to maintain the production levels.

Feb 6, 2023

By Denis Rickman, Jon Windham, Stephen Akers, Byron Armstrong

The soil crater formed by detonation of an explosive charge is of considerable military interest because of the common use of explosives to create soil obstacles. The soil crater is also an important piece of forensic evidence for the investigation of terrorist bombings. With recent advances in numerical codes, modeling and simulation of explosively-formed soil craters is becoming an attractive means of analyzing this phenomenon. Consequently, the need exists to better understand the relationship between soil properties and the resultant soil crater. An extensive database has been developed for the case of explosives detonated in or above in-situ soils of various types. However, in most cases, the soil properties were either not adequately quantified or the soil materials themselves varied such that the gross properties were poorly understood. A research program is underway to improve methods of relating soil crater dimensions to soil identification properties such as USCS classification, particle-size distributions, and Atterberg limits, as well as to soil composition properties such as density, moisture content, and volumes of solids, water, and air. As part of this effort, both explosive detonations conducted over well-controlled and well-documented soil backfills and companion numerical simulations were studied. This paper presents an overview of the effort.

Jan 1, 2010

By K. Hausmann, W. Whelchel

The properties of ethylene Ionomer resins for the inner layer of non-electric shock tubes will be discussed in detail, and opportunities for property enhancement will be pointed out. A stiffness program for prediction of shock tube stiffness, as determined by the stiffness of the individual layers, will be presented and discussed.

Jan 1, 2010

By Scott G. Giltner, Alex Schwenk

This paper is an update on a paper presented at the 2022 ISEE conference. The original paper presented how the mine operator desired to open up ore reserves near several mine structures including two crushers, the conveyor belt drive and the concentrator thickeners. In order to open up additional ore for extraction (over 3 million long tons or 3 million tonnes) it was necessary to blast out two benches near the mine structures. Since the two benches have been successfully shot, the mine has now conducted nine production blasts in this area at distances as close as 116 m (380 ft) to the two primary crushers. These production blasts are full size production blasts consisting of up to 300 or more blast holes. For these blasts the two primary crushers were still the critical structures as they were the production life blood of the mine. If the crushers were shut down due to any damage from the blasting, the revenue of the mine would be adversely affected. As with the initial bench blasts, two issues provided an extra challenge to the blast design. The first was that the blast holes were still considered large diameter at 12¼ inches (311 mm) and 16 inches (406 mm). The second issue was that the bench heights were short, with the average varying from 34-40 ft (10.3-12.2 m). This combination of large diameter blast holes with a short bench provided an unfavorable geometry for the goals established by the mine management. The mine management established the following goals. 1) None of the mine structures would be damaged by fly-rock. 2) Minimize the blast vibrations at the crushers. 3) The last goal was to produce a muck pile that could be dug easily by hydraulic shovels. Electronic detonators were applied to achieve the necessary control of the blast and optimal fragmentation throughout the mine. UAV surveys of the blast area were also conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. The results of the nine blasts have provided what the customer requested. The peak vibration level at the crushers for the nine production blasts was 1.6 in/s (40.6 mm/s) at a frequency of 18.9 Hz. There have been no fly-rock or blast vibration issues at any of the nearby mine structures. As a result, the mine has been able to maintain its production with no downtime. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Ruilin Yang

Techniques for the study of blast vibrations, such as monitoring, analysis, and modeling are often misused between near field and far field blast vibrations. This paper discusses the differences between near-field and far-field blast vibrations in terms of these techniques. A typical example of a near-field blast vibration problem is a blast vibration in the crest of a new highwall behind a cast blast. In such a case, the blast can be a couple of hundred feet long and the distance from the blast holes to a monitoring station may only be 100 feet or less. In this situation, the size or spatial geometry of the blast is not negligible compared to the distance from the blast to the vibration monitoring point. On the other hand, a typical example of a far-field blast vibration problem can be a quarry blast with a nearby residence house. In this case, the distance from the blast to the house may be several thousand feet. The size of the blast is less than a couple hundred feet long and negligible compared to the distance from the blast to the vibration monitoring point.

Jan 1, 2007

By Robert Martin, Brian W. Stump

As part of a series of seismic experiments designed to improve the understanding of the impact of mining blasts on verifying a Comprehensive Test Ban Treaty, a sixteen station network of three-component seismic sensors were deployed around a large cast shot in the Black Thunder Mine. The seismic stations were placed, where possible, at a range of 2.5 kilometers with a constant inter-station spacing of 22.5 degrees. All of the data were recorded with the seismometers oriented such that the radial component pointed to the middle point of the approximately 2 kilometer long shot. High quality data were recorded at each station. Data were scaled to a range of 2.5 kilometers and the sum of the absolute value of the vertical, radial, and transverse channels computed. These observations were used to construct radiation patterns of the seismic energy propagating from the cast shot. It is obvious that cast shots do not radiate seismic energy isotropically. Most of the vertical motion occurs behind the highwall while radial and transverse components of motion are enhanced in directions parallel to the highwall.

Jan 1, 1997

By Navid Mojtabai, Jaak J. K Daemen

Some facilities require ground vibration limits that are far below typical vibration levels of interest in most blasting situations. A possibly extreme example of such a facility might be the proposed SSC (Supercollider Super Conductor) high energy particle study system. The applicability of conventional blast vibration predictors for such a low amplitude vibration is highly uncertain. For this preliminary study, a series of field measurements are made, and the results integrated in a set of vibration predictor equations. Ground vibrations induced by blasting operations at one proposed SSC site are monitored at close distances (hundreds of feet), intermediate distances (miles), and long distances (tens of miles) from the blasts. Peak particle velocities are recorded at short distances, ground displacements at other points, as well as frequencies. Theoretical analyses are performed by integrating all data in a variety of ground vibration predictors. From the statistical analysis of the data, ground motions at various points along the ring site are predicted for a given charge weight. The approach taken appears adequate for making tentative estimates of exceedingly low amplitude vibrations at great distances from mine blasts.

Jan 1, 1987

By Lon Santis, David Buckwalter, Ken Steinmetz

This paper describes a magazine security system using two readily available cellular telephone-based technologies. The system is comprised of vibration sensors and remote cameras. The system is used at a Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF) licensed explosives storage location in Pennsylvania to comply with PA Department of Environmental Protection (PADEP) regulations. The system provides instant notification to the licensee via cellular modems, text messaging, phone call, and e-mail. Likewise, the licensee can control the system remotely over the internet and using text messaging commands. The vibration sensors attach to the door of the metal type I magazines magnetically and detect any movement or vibration. The cameras trigger on movement and thermal radiation changes and can also be triggered manually to check alarms received from the vibration sensors. The previous system was comprised of a base unit and magnetic strips. The magnetic strips were powered by a hard line from the control unit and mounted on the doors and top of magazine creating a bond, that when broken triggered an alarm. Our main issues with the unit were the delay in alert times and tech support. Because of these issues, we decided an upgrade was necessary. Compared to that previous system used at this site, these new systems are highly affordable, carefree and reliable.

Jan 1, 2014

By John Brulia, Grant ODell

The AIRDEK blasting method has recently been introduced as an overbreak control blasting technique. This paper discusses the use of a modified AIRDEK blasting method for use in open-face blasting to make cap stone riprap (6-20 ton size) at the Clinton Point quarry of New York Trap Rock Corporation, Lone Star Industries.

Jan 1, 1990

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By Valeri Mitkov

Studena Quarry is one of the main suppliers of inert materials for concretes production in Sofia. It is characterized by massif heterogeneity in density and fissuration. Failure to take into consideration this fact during the planning of the blasting works recently had unsatisfying results in their carrying out – obtaining of materials with too small dimensions or high percentage of outsize material. Series of test blasting were carried out to find the relations for calculation of the main parameters of the drilling and blasting works. The blasting network was enlarged to 6 x 6 m, the diameter of the shot-boreholes was changed from 110 to 152 mm, the stem of the boreholes was significantly reduced and the relative consumption of blasting agents as a whole was reduced to 0,37 ?g/m3.

Jan 1, 2010

By Italo Onederra, Gary Cavanough, Ewan Sellers

Reactivity of ammonium nitrate based explosives is associated with the presence of iron sulfides in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. The stability of explosive products can also be linked to in-hole density, which influences detonation efficiency, breakage performance and the potential generation of Nitrogen Oxide (NOx) fumes. Reactive ground testing involves detecting a temperature rise of a mixture of a bulk explosive product sample, a ground rock sample and some specific chemical agents. This paper describes improvements in reactive ground testing involving the use of time lapse video analysis and detection of NOX gas emissions from the sample. Reactivity is stored and linked to a using cloud based software to map of the mine showing the exact location of the sample. The location marker can be selected to allow quick access to the sample test results and video. In addition to reactivity, the stability and detonation performance of bulk product can also be influenced by depth. In this paper, a system that simulates product at depth and measures density changes and monitors the structure of bulk samples is described. Results from an explosive product are analyzed and detonation performance is assessed by the measurement of velocity of detonation and detonation pressure.

Jan 1, 2018

By C. Zuniga, S. Combrinck, C. Peters

Agnico Eagle Gold have partnered with Enaex Australia at their Fosterville gold mine to leverage a combination of drill and blast technologies to optimise underground development mining. The mine is the first site globally to collaboratively develop and trial Enaex SWIFT electronic development detonators, which utilise a novel approach to the user interface, simplifying implementation and enabling the benefits of electronic initiation without the complexity of a conventional system. This has been combined with the use of a Sandvik 422i smart jumbo, and the Enaex underground emulsion charging unit with the capability to tailor the delivery of explosives as required and report on a hole-by-hole basis. The combination of these technologies enables full engineering oversight of the development cycle, in turn enabling optimisation of this process in a historically conservative application. The methodology for leveraging these technologies is to bore a controlled and defined blast pattern through using a smart jumbo, load the blast holes utilising lace loading to deliver a desired quantity of ammonium nitrate emulsion per hole, with the ability to reduce chargeweight for perimeter control, and utilising Enaex SWIFT electronic detonators with flexible template type pre-defined delays to initiate the blast holes. Subsequent to firing and excavation the performance of the blast in fragmentation, advance efficiency, and overbreak and underbreak is measured and reviewed. This is then used to optimise the development cycle and apply to other parts of the mine.

Feb 6, 2023

By Joshua Micah Hoffman

While it is easy to state that meaningful involvement of the community can play a critical role for a successful blasting operation, following through with this involvement is not an easy task. Structured Public Involvement (SPI) is a developed protocol for involving communities in project planning decisions and could be readily applied to the blasting industry. SPI was developed for the purpose of collecting quality public input about public transportation projects. The purpose of SPI is to bring about stakeholder satisfaction with potential projects by allowing controlled input from the stakeholders. It was designed and intended for democratic societies that have come to expect a voice in public projects. While blasting operations are not always in the domain of public projects, the fundamental process outlined by SPI can be useful for collecting feedback from the immediate public around blasting operations.

Jan 1, 2014