Search Documents

By Lewis L. Oriard

The purpose of this paper is to provide an overview of close-in blasting effects on various types of structures and building materials, as encountered in this writer's professional practice. Structures range from old, deteriorated historical monuments to new, heavily reinforced buildings. Materials range from clay adobe to concrete and steel. Site locations range from tropical to arctic. Blasting ranges from sculpture blasting inside buildings to "coyote" blasting and large surface blasting operations. Space limitations permit a brief discussion of only 25-30 specific cases, but they have been selected to be typical of conditions found on hundreds of similar cases. The writer was asked to present a discussion of representative cases where relatively high vibration intensities were experienced. Virtually all of these cases were free of damage, but the few damage cases provide valuable insight to the mechanisms involved. Observations of such damage and non-damage cases have served as the basis of this writer's criteria for various structures and materials, as well as the technology to conduct blasting operations within those criteria. A sampling of these experiences is gladly shared with the reader.

Jan 1, 1991

By Earl C. Hutchison, Gene Smith

Extensive blasting was required to construct an underground tunnel for a 90 inch sewerage relief line. The tunnel and required excavation extended under an upper middle-class residential area in Atlanta, Georgia for more than a mile and a half and required the use of more than a half million pounds of explosives in the immediate vicinity of houses and residential apartments valued at more than 16 million dollars. Other houses and property valued at more than 80 million dollars were within range to claim blasting damages. An effective blasting damage control program was carried out which limited the number of blasting damage claims to less than 2-1/2% of the total number of potential claims. All but three of the small number of blasting damage claims which were made were effectively denied without any resulting legal actions and less than $3,800 was paid for settlement of the three claims.

Jan 1, 1981

By P D. Katsabanis

The phenomenon of sympathetic detonations in blastholes is investigated by comparing experimental observations and numerical modelling results. Numerical modelling using the TDL computer code and Forest Fire decomposition rates for commercial explosives has shown the importance of blasthole diameter, impedance of stemming material and host rock. Comparison with experimental observations has also shown that sympathetic detonations cannot always be treated as shock to detonation transitions (SDT). Examination of previous results which have been obtained from calibrated low amplitude shock experiments reveal that there is an ignition threshold prior to the detonation threshold. The difference between the two thresholds is more pronounced in the case of air bubble sensitized products. The ignition threshold can be very important under the confinement provided by the blasthole and the conditions of application. It also correlates well with the pressures expected at the gap distances of interest in the practical application. It is suggested that critical energies are used as the criterion for cross initiation in blastholes. Practical suggestions based on the numerical calculations and experiments based on these calculations are also given and discussed.

Jan 1, 1992

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985

By S S. Kahlon

India is a large and growth market for explosives and accessories, which has dramatically changed from complete import dependence to self sufficiency, and now has an exportable surplus. The largest single user is coal mining which is continuing to show a healthy growth with opencast mining becoming increasingly dominant. The explosives industry has kept pace with mining and today all the well renowned explosives technologies of the world are available in the country. While slurry explosives are popular in large diameter, NG based explosives continue to be preferrred in small diameter usage. Emulsion explosives have had a good market response. ANFO usage is limited due to local reasons. As the mine size is increasing, the demand for bulk-on-site explosives is growing. Prices of explosives and accessories are cheap compared to international levels. The user industry is mainly Government owned mines whose profitability is not satisfactory. Explosives industry is over licensed in terms of manufacturing capacity, which is likely to put pressure on the viability of some of the explosives manufacturing units. Scope exists for optimization of blasting parameters through the use of computerized blasting models. The explosives industry is faced with new challenges and opportunities.

Jan 1, 1987

By Bengt Ljung

Manual charging of long upward drilled holes in mines is a heavy and risky job today. Mechanization of this work has been requested for some time by miners, their supervisors, industrial safety organizations and the trade unions, all of whom are interested in improving the working environment. This paper presents newly-developed charging systems intended primarily for charging in connection with sublevel caving and sloping. These systems have been field-tested during 1977 in the LKAB mines in northern Sweden. The results of these field tests and the results of laboratory work conducted to help eliminate the risks involved in charging explosives are also discussed. The equipment being tested (see fig. 1 and 2) consists of a charging vehicle with articulated steering, the PT-60, which has been equipped with a hose feed system mounted on the hydraulic extension boom. From a sheltered position, the operator brings the detonator and primer to the hole opening, after which the hose is pushed in mechanically to the end of the hole. Measuring equipment indicates when and if the end of the blasthole is reached. The operator then withdraws the hose mechanically as charging takes place.

Jan 1, 1978

By Frank Lucca

This paper includes research and investigation into blast design and blast optimization for vibration control in municipal and tight blasting situations, where specifications were extremely stringent. The paper is written for the field blaster to understand and develop blast plans based on field conditions. The paper includes blast design considerations, utilizing seismograph arrays to check and predict vibration results, and problems encountered in vibration monitoring in extremely tight situations (0-20 feet). Blast vibration frequency, acceleration, peak particle velocities, and relative displacement are discussed with effects in the near and far fields and blast designs utilized to stay under limits. The paper also discusses using the latest in technology for blast design to control vibration. Equipment includes 2D and 3D laser profiling systems, digital video, fragmentation analysis, seismograph arrays, and borehole tracking devices. Other topics are discussed such as public relations, working with regulatory personnel, unions, and other project consultants, and the problems associated with municipal blasting situations, such as, flyrock and proximity of other personnel and equipment on the project.

Jan 1, 2004

It has been common practice for many years to predict and control underwater blasting effects on the basis of certain simplified theories related to the pressures generated by underwater detonations. Unfortunately, two of the most commonly applied concepts in many instances do not provide an accurate modeling of typical field conditions nor the potential for damage. One of these concepts is that the damage potential is related directly to the peak pressure generated by an underwater detonation, without regard to the time history of the pressure pulse. This belief has led to the widespread use of air bubble curtains to reduce peak pressures, without considering the effect that air curtains have on the time history of the pressure pulse. At times, this procedure can be unwise. The other concept is based on the premise that pressure pulses in solids (such as rock) will always be transmitted to nearby water bodies in agreement with the theories of the transmission of plane waves across normal (perpendicular) boundaries. In reality, such conditions are quite rare.

Jan 1, 1985

By Thomas E. Ricketts

Limited void volume blasting (LVVB) occurs when rock is blasted into a volume that is not sufficient to let the rock expand to its free-bulking value. The freebulking value is obtained when the rock particles have enough space to separate, tumble and rotate to produce the maximum amount of void possible between the fragments when they finally come to rest. Although bulking value depends on particle size distribution and shape, a typical free-bulking value for uniform, finely broken shale is about 1.67. LVVB occurs in almost every type of blasting used in both surface and underground mining operations. For example, in multiple-row bench blasting for surface mining, the final delays that are designed to fragment the rock furthest from the free-face are generally confined by previously blasted rock which results in a LVVB situation. In underground mining, the blasting is automatically confined and is commonly done intentionally to limited void volume to reduce mining cost and improve safety. LVVB primarily affects rubble bulking and thus the excavation of the broken rock which is related to the productivity and economics of a mining operation.

Jan 1, 1989

By Claude Cunningham, Szendrei

The partitioning of blasting energy into “Shock” and “Heave” components is a popular concept for attempting to match explosives to particular ground conditions and blasting results. The issue is complex, as it affects both the detonation process and the immediate response of the rock skin. However, the fundamental process of energy transfer from the explosive to the rock through the blasthole wall is not well defined. Clues to the “Shock” phase of blasthole expansion are given by cratering behaviour of materials subject to high velocity penetrators. The final cavity volume defines both the energy used to achieve this and the resistance of the confining material. Attention is being given to the link between penetration of a solid target and expansion of a readymade hole, both producing the same outcome. The benefit of this work is that it leads to clearer understanding of how explosives will impact upon the blasting results and helps to explain the energy consumption in blasting.

Jan 1, 2004

By Diane F. Baker, Cathy Aimone-Martin

A series of small-scale explosive experiments were conducted in a perlite mine near Socorro, New Mexico. These experiments were a joint effort between Los Alamos National Laboratory, New Mexico Institute Of Mining and Technology, Southern Methodist University, and Defense Nuclear Agency. The purpose of these tests was to measure the changes in the shock wave and seismic coupling as a function of depth of burial and structural setting. The size of the explosive charges ranged from 1 to 68 kg. Over 1150 measurements of velocity and acceleration were made on thirteen experiments using three component sensors. The sensors were placed to maximize the azimuthal coverage as well as to provide data at a variety of ranges from ~1 to 130 m A few far field measurements were made at ranges of ~2Êkm. While the bulk of the measurements were made on the surface, high g accelerometers were placed in one instrumentation borehole to provide some free-field measurements. Preliminary results indicate that significant differences in the amplitudes of signals can occur when the location of the explosive charges are changed by only meters. Part of the observed difference is attributed to variations in the rock immediately adjacent to the charge affecting the shock coupling; and part to the effects of the site characteristics.

Jan 1, 1994

By James H. Redyke

In August, 1980, while finishing construction of the new stack, one of the flues mysteriously collapsed, killing three people and injuring several others. Several months later a British international steeple-jack company was hired to demolish the remaining portion and make a detailed inspection of the balance of the chimney. During this contract almost one hundred core samples were taken from all parts of the structure including the 32-inch thick base. As the result of these tests and the investigation, the Power Company decided to demolish the complete structure. Because of the critical time element, the decision was made to use explosives in the removal of the structure. To give you some perspective as to the size and dimension of the stack, it was 900 feet tall, 80 feet in diameter at the base, and 70 feet in diameter at the top. The two remaining flues were 25 feet in diameter and extended 30 feet beyond the top slab of the chimney. The outside of the structure was referred to as a wind shield. The lower 120 feet were 32 inches thick and the remaining 780 feet were 12 inches thick. The decision was made to prepare and shoot the chimney at the 120-foot elevation because the debris from the collapsed flue was confined in the base section and could not be easily removed. After extensive and costly engineering, we determined it was necessary to construct steel columns to bear on the lower 120-foot section, which would act as a hinge and guide during the dropping of the structure.

Jan 1, 1982

By Y. Hirosaki, H. Hamashima, Y. Itoh Kato, S. Tanaka

The emulsion explosives show non- ideal detonation behavior, and its detonation velocity can be controled by selecting the size and adjusting the quantity of voids involved. To establish the technology to control the detonation characteristics of the emulsion explosives, some experiments have been carried out using resin balloons of five different sizes ranged from O.OSmm to 2.42mm in the average diameter. Detonation velocities of the emulsion explosives containing resin balloons of different size and quantity were determined for the charge diameter of 20-50mm. The detonation velocity at infinite charge diameter was compared with calculated ideal detonation velocity. The emulsion explosives containing large (0.5mm or larger) balloons showed big discrepancy between the measured and calculated detonation velocities, and the fraction of ammonium nitrate reacted in the reaction zone was estimated to be significantly low. It was shown that the reaction zone length was proportional to the size of voids involved. The critical charge diameter was determined for the emulsion explosives containing different resin balloons at the various explosive densities. It is large for the emulsion explosives containing large voids, and it was shown that the critical diameter is proportional to the distance between the void surfaces, not to the void spacing, the distance between the centers of the voids. The reaction rate of the bulk emulsion matrix seems to be the major factor that affects the critical diameter than the specific surface of voids. Good relationship between the critical diameter and the reaction zone length was observed.

Jan 1, 2000

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

Jan 1, 2005

By Paul Sairato, Cathrine E. Johnson

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. This paper provides the data from a second, restructured, online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2015

By Edward Fitch

The DOE is evaluating Yucca Mountain, Nevada as a potential site for disposal of high level nuclear waste. Yucca Mountain is located approximately 160 km northwest of Las Vegas on the western edge of the Nevada Test Site and the Nellis Air Force Range. An exploratory tunnel has been constructed through Yucca Mountain for site characterization. A controlled drilling and blasting technique, smooth wall blasting, was used to excavate the TBM starter tunnel and alcoves off the main tunnel to provide areas for scientific investigation. Fundamental to the blasting program has been the use of two blast design equations used in concert to minimize blast damage to the surrounding rock mass. The first of these equations was developed by Roger Holmberg and estimates near-field peak particle velocity that is the basis for minimizing blast damage to the host rock. The second of these equations was developed by B. H. Sanden and provides bore hole pressure estimation which allows controls to minimize crushing of the rock mass along the perimeter yet allowing enough force to create tensile failure between perimeter bore holes. This is key to the smooth wall blasting technique. To date, essentially the same controlled drilling and blasting program has been in place for all excavation requiring controlled drilling and blasting at the ESF. The controlled drilling and blasting program uses an iterative process to achieve continuous improvement in the blast rounds. This involves interaction between Architect and Engineer (A/E), Constructor, and Testing Coordination O&e (TCO) to ensure each blast round successfully meets the expectations of affected participants. The A/E requested that the TCO provide validation of the near-field peak particle velocity estimation under the Construction Monitoring Program. Data gathered under this program were reduced by statistical analysis and used to verify blast design parameters and provide a site specific blast damage relationship.

Jan 1, 2000

By Joshua Hoffman, Catherine Johnson, Braden Lusk

Blasting conducted in surface coal mining operations in the Appalachian region consumes a significant amount of blasting agents. Emission of oxides of nitrogen (NOx) from these operations potentially represents an environmental challenge. This paper presents work conducted to quantify NOx output from the detonation of blasting agents common to surface blasting operations in surface coal mines. Annual ANFO and emulsion consumption data was collected from an operational surface coal mine located in West Virginia. It is known that many factors contribute to the types of gaseous byproducts released from the detonation of explosives. These factors include but are not limited to: fuel to oxygenator ratio, degree of confinement, and contamination. While, past research has been conducted to study the relationships these factors play on the release of NOx, these findings do not agree with one another. The annual explosive consumption values from the West Virginian mine were applied to NOx emission conversion factors in published literature. This lead to a range of NOx emissions from 95 to 914 tons in a year. Given the wide range of NOx production the utility of this information is suspect. The EPA recognizes a standard factor of 17 lbs (NOx)/ton (ANFO) however this factor is based on chemical composition and does not address contamination, confinement, or AN to FO ratio. This factor when applied to the West Virginia Mine's explosive consumption produced a value of 215 tons of NOx. There is a lack of information on NOx emission from emulsion type explosives. The work presented in this paper can be used by blasting professionals to quantify NOx emissions and guide future work for producing better predictor factors.

Jan 1, 2014

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998

By Martin Chenoweth

The Metropolitan Water District of Southern California (MWD) is undertaking one of the nations largest water management projects. The Eastside Reservoir Project is being built to insure a supply of water to Southern California in the event of earthquake damage to the aqueducts supplying the region. An 800,000-acre-ft lake will result from the three dams, closing off the valley between two parallel ridges. The single largest contract of the project, the West Dam, was awarded to the joint venture of Atkinson Construction Co., Washington Construction Co. (Morrison Knudsen Co.), and HB Zachry Co. Over 50 million bank cubic yards of rock must be drilled and shot on this contract alone. AWZ relies on the TechBASE database management system for documenting drilling and blasting. The database format of TechBASE allows all production parameters to be linked to the location of the activity. This allows parameters such as drill penetration or boulder production to be analyzed for geologic trends that can either be exploited or dealt with. Shot locations are stored as 3D polygons in a polygon table. Production and cost data are stored in flat tables. Shot names are unique and link the polygon table to the flat table. This allows typical database queries to be made by date, location, cost or any production parameter. The output from these queries can be presented in table, graph and as map formats. The map output is particularly helpful in quantifying geologic conditions and blast performance. The ability to transform the data into information has been very helpful. The ability to present this information graphically has been invaluable.

Jan 1, 2000

By David Harrison, Brian Harrison

The Army Corps of Engineers completed the Charleroi Lock and Dam in 1932. It is located on the Monongahela river approximately 22 miles (35k) south of Pittsburgh in Charleroi, Pennsylvania. It is comprised of a 420-foot (128m) gated dam, and a 720-foot (219m) by 56-foot (17m) land side lock, which provides for a 16.6 foot (5m) vertical lift.

Jan 1, 2018