Search Documents

By Wilfrid Comeau

Since 1967 Hydro Quebec has undertaken the control of blasting and its effects at its power development sites. Blasts have been monitored using a commercially available three component seismograph. Initially, vibration records were used to establish the relationships between vibration level (resultant of three components), explosive weight and distance for various blasting operations.

Jan 1, 1977

By Michael D. Duffy, Martin W. Chenoweth

"Tenn Luttrell Company (TLC) is a major lime and limestone producer in the eastTennessee area. The property, which isreferred to as the Chesney Mine, has been mined from the surface and underground overthe past 20 years. The ore body consists of three major zones of chemical grade limestonewhich lay at a dip of 30 _ 65 degrees. In July of 1989, Tenn Luttrell Company made thedecision to reopen the underground operations which had been suspended during a time ofincreased surface mining."

Jan 1, 1993

By James Barker, David Leidel, Don Crawford, Daniel Dorffer

This paper describes the test processes performed to ensure the suitability of an RF-safe detonator for use in oilfield explosives operations on land and offshore locations where RF silence cannot be implemented or the distances from explosive systems arming operations to the RF source or sources are too close for conventional resistorized hot-wire detonators based on the safe distance tables. The test program for the detonator assembly was based on MIL-STD-461E, “Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment”, 20 August 19991.

Jan 1, 2008

By Francis O. Otuonye

An application of a time series and systems analysis modeling technique to blast vibration data is discussed. The vibration data was taken from a rock support structure and the surrounding rock mass at distances close (less than 15 feet) to a blast. The analysis technique provides quantitative information on the frequencies of ground motion as well as the frequencies and damping ratios of a near-field support structure.

Jan 1, 1994

By Doug Hoy

The scope of the Cliff Avenue Reconstruction Project in Sioux Falls, South Dakota was to widen a two lane highway to five lanes, along with removing and reconstructing both above and below ground utilities located along the project limits. The objective of this paper is to present the blasting techniques used in the rock excavation phase of the Cliff Avenue Reconstruction Project.

Jan 1, 1992

By T Guiliani, F Ottuonye

Explosives casting is gaining increasing popularity as an overburden removal method in strip mining because the coats of using explosives to cast a percentage of the overburden to the spoil are lower than the costs of using stripping shovels or draglines to do all the overburden removal. This is due to the rising capital and operating costs of draglines and shovels.

Jan 1, 1989

By Joe Sr Strobbe

In 1933 the Cobre Mining Company re-opened the 32-year-old UV Industry Mine, which is located in a scenic canyon near Silver City, New Mexico. The site location is shown in Figure 1. Current mineral extractions are copper and magnetite; both extractions similar to those mined many years ago. Copper is extracted from chalcopyrite imbedded in the host rock of massive limestone deposits and magnetite, an iron ore, is a by-product of the same extraction process.

Jan 1, 1998

By Feng Shuyu Yang Nianhua

According to the results of high speed photography tests, particle velocity measurement tests and the digital calculation with TP2 software, the shape of shock wave, the declined laws of the shock wave propagation speed and the peak particle velocity are described and analyzed in detail. New viewpoints about the theories of blasting fragmentation based on analysis of the progressive pictures of the fracture region are given. The formula for calculating the depth of fracture regions is established on the basis of the new viewpoints.

Jan 1, 1997

By Jacques Monette, P K. O'Connell, Keith Boyle

The mine contracting industry in Canada is no different from any other industry in its quest for productivity improvements. Dynatec Mining Ltd. has focused on drilling and blasting of rounds as an area for improvement. This paper describes the development of blasting long rounds in shaft sinking as well as a description of the lateral excavation system as applied at Aur Resources Inc., Louvicourt Project.

Jan 1, 1994

By John F. Mitchell

Large production blasts involving many series in parallel have long been a source of complication. When speed and accuracy are most necessary in blast preparation an efficient and precise method of wiring is required. After loading a large number of holes and being pressured for time, due to lack of daylight, equipment shutdown, etc., an effective hook-up plan can eliminate many last minute problems. It is the intention of this paper to offer a simplified wiring proceedure which when employed can save precious time and encourage efficient and economical utilization of blasting personnel and material.

Jan 1, 1976

By J L. Jethwa, A G. Gaithankar

The paper deals with a software method developed to design the optimum blast parameters for tunnels and mine roadways for a given set of geo-mining condition without any major discontinuity. The application of the software is presently limited to 8 D-ahaped excavation where inclined hole cut or four-section parallel cut is used with smooth blasting technique.

Jan 1, 1993

By Jeffrey E. Loney, Andrew F. McKnown

Recovery of contaminated groundwater migrating through bedrock can be very difficult due to the low transmissivity of many bedrock fracture systems. To overcome these difficulties, a system of controlled "trench" blasting has been used on several projects to assist in cutting off and collecting groundwater plumes in bedrock. By using a combination of trench blasting and presplitting techniques, linear "fracture" zones are created in appropriate locations to significantly increase flow into recovery wells and control plume migration.

Jan 1, 1995

By Anne Charline Sauvage

Blast designers and blasters need to know the rock mass influence on blast to increase explosive effi-ciency and to optimize costs, but also to succeed in limiting blast emissions (vibration, overpressure, flyrock) This paper presents an applied approach which makes it possible to structure the information con-cerning the rock mass and the blasting.

Jan 1, 2013

By Charles H. Dowding

This paper describes NUVIB, analytical software to digitize, analyze, display, and plot time histories generated by blasting and construction vibrations. It is available in conjunction with a new book on Construction Vibrations (Dowding, 1996) through internet procedures described at the end of the chapter on analytical software These internet based procedures eliminate the need for inclusion of disks in the book and take advantage of the growing electronic communications network. Perhaps more importantly this procedure allows the software to be updated more often than the book is reprinted.

Jan 1, 1997

By James W. Reil, Douglas A. Anderson

Common wisdom has it that a blast which breaks rock efficiently should-generate less ground vibration. In practice, however, this idea has not been-rigorously tested. In a previous paper presented at an SEE meeting[1] we described a method for-controlling vibration using delays. The method is very effective in controlling-annoying low-frequency ground vibration. We noted that observed ground-vibration differs in some respects from that predicted by adding single-charge-waveforms.

Jan 1, 1988

By K Ramachandra Rao

This paper explains the methodology for assessing the efficiency of rockmass fragmentation by explosive blasting, from ground vibration frequency spectrum analysis of the blast event. Explosives are used in the mining, quarrying and construction industries for fragmenting rockmass to a suitable size. When an explosive charge is detonated, in addition to fragmenting the rockmass, it will also generate ground vibration and air vibrations. Efficiency of a blast depend upon percentage of blast energy wasted in generating ground vibrations and air vibrations.

Jan 1, 1994

By Wang Xuguang Shen Yingfeng

Structure is the main aspect affecting the performance of emulsion explosive. Calculation of such structure parameters as osmosis pressure, interface area per unit volume etc. must be helpful to the understanding of the structure of emulsion explosive. This paper has solved the Laplace-Young Equation for simplified monodisperse emulsion system by Galerkin method, and gained the relationship between mean curvature, contact angle, volume fraction, fractional film area and interface area per unit volume. The paper also presents a new expression of osmosis pressure at non zero contact angle.

Jan 1, 1998

By T Michael LeBlanc

Drill trajectory deviation is a recurring problem in vertical retreat stoping operations. As a result of this deviation, 60 kilogram (165 millimetre diameter) and 103 kilogram (302 millimetre diameter) explosive charges are routinely detonated beyond ore/waste contact zones. Consequently, there follows a reduction in finished stope wall stability and an increase in ore dilution.

Jan 1, 1996

By Yuji: Wada Ogata, Kunihisa Katsuyama

It is well known that a compressed stress wave reflects at the free face, it propagates to the backward as a tensile stress wave, and cracks grow when the tensile stress becomes the dynamic tensile strength. The behavior of these cracks has been discussed through the observation of the dynamic photoelastic high speed photography.

Jan 1, 1993

By Sharon K. Reamer, Yvan Sifre, Klaus-Gunter Hinzen

"Three case studies are presented that illustrate the successful application of firing timeoptimization (hybrid modeling) in the quarry environment and for a construction site. In allcases, the method requires the measurement of at least one in situ, single hole explosion asa representative model of the desired blast design."

Jan 1, 1993