Search Documents

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By D. C. Valdemeri, Oppermann J. P. Z., R. G. Schaarschmidt, C. S. Mendonca

This case study was conducted in an aggregate company, located at Estância Velha town, RS, Brazil. The study was based on the results of vibration monitoring mainly in terms of PPV (peak particle velocity) and frequency. Changes in the blasting design were performed to adjust the limits determined by the Brazilian standard NBR 9653:2005. Understanding the seismic wave attenuation for the site, changes in the blasting design were tested to fit the limits, such as reduction of maximum charge per delay, initiation orientation and sequencing and finally the replacement of accessories like "shock tube" by electronic initiation system. The results are shown below.

Jan 1, 2015

By Gordon M. Matheson, David K. Miller

Sinkhole development in karst terrains is a serious problem and risk to facilities built in these areas. The potential for sinkholes are a function of many things including the chemistry of the underlying rock, the location of water conductive fractures and fissures in the rock, the natural fluctuation of the ground water table, vibrations from various sources and surface regrading activities. When sinkhole open near quarry operations the occurrence of these features is occasionally attributed to vibrations from quarry blasting. The purpose of this paper is to review the evidence regarding the development of sinkholes as a result of quarry blasting. In general, it has been found that sinkholes result from collapse or piping of overburden soils into cavities or caverns developed within underlying carbonate rocks that have been in existence for many thousands of years. The overburden soils in karst areas are typically clayey and as a result are not subject to densification or liquefaction as a result of vibrations. The primary cause of an increased rate of sinkhole development can be attributed to changes in the ground water table or local surface water drainage. These changes may be caused by seasonal fluctuations, ground water level lowering in drought periods, dewatering of excavations or quarries, or local changes in surface drainage resulting from grading activities.

Jan 1, 1998

By Michael S. Wieland

Toxic fume concentrations from industrial mining explosives depend somewhat upon the type of rock (or other strata) confinement. Though traditional detonation theory disregards this influence, the work principal from thermodynamics reveals it, when the violent interactions that transpire within the rock blast are taken into proper account. Resolution of the work principle technique requires total thermodynamic equilibrium under constraint, so the nonequilibrium dynamics is rendered in that way, using an old trick from theoretical mechanics that revises the representation of forces. The rock pressure reduces to a four-component sum: the rock compressive strength and natural atmospheric pressure, as reckoned quasi-statically, and the gravitational influence and reversed inertial resistance, as reckoned dynamically. Tabulated specie concentrations and graphical trends reveal the dependency upon rock pressure, rock temperature and the fuel-oil percentage in ammonium nitrate mixtures (ANFO), used to illustrate the model. Rigid-wall test chambers have notable ullage (residual space), where rapid expansion influences the reaction quenching, yielding a fume spectrum unlike that for rock confinement; reported rock tests are therefore used for comparisons. For the thermodynamic regime where quenching occurs, seven concentrations are resolved, including carbon monoxide (CO) and total nitrogen oxides (NOX). Their trends yield inferences regarding the way unwanted charge desensitization from transitory hole-to-hole wave impact in conjunction with reduced rock pressure can yield nasty toxic fumes, the dark rusty cloud phenomenon!

Jan 1, 2005

By Atsuo Inoue, Toshihiro Ogata, Hideaki Sugihara

Generally in Japan, since ANFO has easy handling and low-price, it is most used as industrial explosives. However, ANFO is very easy to dissolve in water, it is difficult to use under existence of water and the consumer have desired water-resistant ANFO which has perfect water resistance. Then, we have developed the Water-Resistant Granular Explosive (It is written as following WRGE.) in which the surface of the explosive was covered by waterproof film, so that WRGE is able to use in hole with water. We ran various performance tests about the WRGE developed in the laboratory. Consequently, WRGE has water resistance of over 6 hours, and it has been checked that a performance and handleability were equivalent to the conventional ANFO. Then, we carried out the field test in the consumption site, and did performance evaluation on an on-site level. As compared with ANFO, fragmentation (size and volume) and handleability are almost equivalent. However, some problems which the WRGE is not settled out smoothly in hole with water and need more time for loading were also clarified. We are going to continue some advanced improvements through field tests.

Jan 1, 2005

By Pharis E. Williams

The ability of voids, microballoons, and even solids to sensitize explosives has been known and used for many years. This phenomenon has generally been studied and reported under the terminology of "hot spots" because of the increase in local pressure and temperature when a shock wave encounters such sensitizers. A method for treating this phenomenon in detonation theory or in a detonation model has been studied for almost the same length of time. Perhaps because of the complexity and non-linearity of the void, or microballoon collapse, several of these studies have used the expediency of including additional terms in the burn rate law to account for the influence of hot spots. The detonation model proposed here considers the sensitization due to discontinuities in the shock impedance to be a mechanical phenomenon to be accounted for in the mechanical equations governing the detonation and not in the burn rate law. While this is not a new contention, the method for handling this non-linear phenomenon within the proposed model is new. The model also includes a method which accounts for the manufacturing variables of emulsion matrix cell size, microballoon size and type, as well as energetic additives.

Jan 1, 1992

By O E. Jr Crenwelge

Recently promulgated regulations governing blast induced ground vibrations in the mining industry contain a frequency criterion as one option for verifying compliance. This criterion is based upon an oversimplified method which assigns the entire peak particle velocity amplitude to one frequency. Depending upon the nature of the vibration time history, it is possible that this frequency may not even be one of the predominant frequencies of the signal. In addition, the criterion does not specifically define the data analysis approach to be used by the industry for obtaining either the amplitudes or the frequencies of the vibration components. And because personnel in this industry generally have little understanding of vibration phenomena, a number of different approaches are currently being used for satisfying the criterion. This paper presents a method for obtaining both the Fourier amplitude-frequency spectrum and the integrated predominant amplitude-frequency components for the vibration record. The method is both physically and mathematically correct and is in common use in a number of other industries. Therefore, it should be of help to regulators, blasters, and consultants charged with developing, enforcing, or implementing ground vibration criteria.

Jan 1, 1988

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Greg Mclellan, Mark Johnson, John Pepper

Several large quarrying projects recently occurred in Miramar, Florida. These were closely monitored by the Seismologist of Record and Broward County in accordance with County and City regulations. In addition to this monitoring, the City of Miramar employed The Pepper Engineering Group, Inc., to provide additional spot check monitoring and to review the records of the other two parties on a routine basis. Broward County ordinances require that the location of each shot and the nearest protected structure be recorded along with seismograph measurement of each shot at the nearest protected structure. The positions of the blasts and nearest protected structures were determined using GPS. The blast vibrations were measured by seismograph. Over 600 shots, which are the subject of this study, were measured both by the County, the Seismologist and, on many occasions, The Pepper Engineering Group. As such, the vibration data was constantly cross-checked for consistency. The blasting contractor also provided blast designs for each shot. In this paper, the measured vibrations are plotted in terms of Resultant Peak Particle Velocity (RPPV) versus Scaled Distance (SD) on logarithmic scales. The data curves are fitted with least squares and upper 95% and 99% prediction limits are provided. Equations are presented to predict the RPPV based on scaled distance and prediction level using power fits. Statistical information concerning the derivation of the various limits is presented. The raw data used to develop this paper, along with other information concerning the shots, will be posted on the Internet for use by other researchers.

Jan 1, 2000

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By Stuart Brashear, Lee Schettler

"The effect of water on several ANFO/emulsion blend ratios is documented by both physicalobservations and analytical testing to demonstrate the effect even small quantities of water canhave on water resistant blends."

Jan 1, 1996

By Jaak J. K Daemen, Clayton R. Morlock

A study was performed to evaluate the predictability of airblast overpressures induces by production mine blasting. Thirty-seven production blasts were monitored using 3 blasting seismographs giving over 100 blast overpressure records. Blasts were monitored at 5 coal highwall operations and at a limestone quarry, all in the midwest. Blasts consisting of small surface charges were monitored to permit an assessment of prediction methods under controlled conditions, as well as to observe actual delay intervals and their influence on the overpressure.

Jan 1, 1983

By J. A. Rodgers, K. C. Whitaker

The time domain during which an explosive detonates and causes rock to fragment and displace is on the order of tens of milliseconds. Because of this, the dynamic processes that occur during this time frame often become a source of confusion when trying to analyze the performance of explosive products in decked blast designs. As an illustration, the authors have experimentally examined explosives malfunction in decked blasts through state-of-the-art measurement techniques. The interaction of explosive products and blast geometry was examined in detail using the analysis of a series of decked blastholes. Explosive and initiator malfunction in decked blasts is often considered to be entirely the result of insufficient inert decking material, however, it is shown that rock properties and dynamic burden conditions may have a significant impact on decking performance. The successful application of deck-blasting technique for control of ground vibration amplitude relies on an understanding of the true dynamic performance of the blasthole.

Jan 1, 2000

By Jung-Hoon Ryu, Chang-Ha Ryu, Byung Hee Choi, Yang-Kyun Kim

Control of overbreak in tunnel blasting is one of the key factors affecting the construction expenses as well as safety. Overbreak causes an increase in the cost of construction by requiring an additional amount of shotcrete. In addition, blast damage to the final rock face may cause instability and rock fall hazards. For these reasons, controlled blasting is an indispensable routine in tunnel excavation in order to get a smooth face and to reduce damage to the final wall. We have experienced a very poor quality of excavation depending on the tunneling sites although a similar design of controlled blasting technique was applied. Field experiments over 40 rounds were carried out to investigate the cause of the poor results in tunnel blasting. In this paper, discussed are the parameters affecting the overbreak and some findings from the field experiments. Overbreak could be controlled considerably by adjusting some parameters before the efforts of developing a new blasting method.

Jan 1, 2004

By Scott Gustfason, Richard N. Snyder

What is a safe stand-off distance? Recent mishaps using conventional blasting equipment have seen flyrock as distant as 3,750 feet from the blast area, or close to three-quarters of a mile, therefore, whether below ground, under water, in surface quarries or at a structural demolition site, data signals riding a radio wave promise a new horizon for the users of both electric and non electric blasting circuits.

Jan 1, 1987

By Geff Gordon, Dale Nies

Small diameter borehole blasting can be very efficient and cost effective. As residential development continues to expand, many areas are now requiring blasting for site preparation and upgrading old utility systems or constructing new ones.

Jan 1, 1990

By B H. A Brown

The components of passive laser survey systems and their relative functions are presented. A general outline of the capabilities and the information available are followed by two case histories. These involve the use of such systems in quarry blasts where loading adjustments and drilling designs were required. Their application in blast casting operations, stockpile measurement, surface and underground construction, and general surveying areas are briefly covered, with comments on the potential for demonstrating a return on an investment in laser survey equipment.

Jan 1, 1990

By Adrian J. Moore, Alan B. Richards, Rob Evans

Air and ground vibration from blasting is influenced by the delay pattern that is used. Wavefronts from blastholes fired in a blasting pattern can combine in certain circumstances to give increased blast vibration levels. A simple computer model has been developed which shows the combined effect of wavefronts from a multi-hole blast and identifies if wavefront reinforcement occurs, and permits delay patterns to be designed which will avoid or reduce wavefront reinforcement.

Jan 1, 1994

By Ed Jr Smith, Calvin J. Konya

The purpose of this paper is to describe the case history of a blasting project conducted jointly by Precision Blasting Services and Cherokee Explosives. It is the intent of the authors to show how blasting could be done in controlled fashion near very expensive computer controlled machinery. The job was done in minimal time with no complaints or allegations of damage in spite of the fact that blasting was conducted within five feet of the equipment and with the 32 acre plant fully operational, with machine operators working within 10 feet of the blasting site.

Jan 1, 1986

By Dirk van Zyl

Rock fabric information is often available from drill hole information and bench face mapping. An approach is presented to predict fragment size distribution of blasted material from this information as well as that obtained after the blast. The following information available from a mineral exploration drilling program was used in the prediction of fragment size distribution: largest piece, percent particles larger than 1 inch and RQD. Photographs of bench faces were used to estimate the fragment size distribution. Fracture spacings were evaluated along a series of parallel lines on the photograph. Photographic techniques were also used to obtain the grain size distribution of blasted material. m is paper describes the methodologies applied in some detail.

Jan 1, 1986