Search Documents

By Monica Stuckert

Field studies were made at an Appalachia coal stripping operation to evaluate the differences in cost and performance between blast casting with pre-split dewatering versus conventional coal overburden blasting.

Jan 1, 1985

By W. Reisz

The fear of heights is a natural defense against performing a dangerous and unnatural act such as standing on the edge of a hundred foot wall. Yet through familiarity, a casual attitude often exists. Those of us, who work near highwalls on a daily basis, may become overly comfortable in our surroundings, losing sight of the disaster which may often rest a single misstep away. And this is where the hidden dangers lie.

Jan 1, 2009

By Randall M. Wheeler

Computer analyses of single hole signatures are often used to help blasting operators predict the type of ground vibration effects that may be produced from production blasts incorporating various delay intervals. Frequency analyses of single hole waveforms and subsequent multi-hole waveform simulations can allow an operator to determine the best type of delay intervals to use in order to minimize low frequency ground vibrations.

Jan 1, 1989

This paper describes experience in designing and implementing casting blasts over the past fifteen years. Important design parameters such as powder factor, burden and spacing, blast pattern geometry, front row burden and toe distance, pit width versus height, blast length, explosive selection, millisecond delay timing and tie-in types are discussed.

Jan 1, 1995

By William R. Adamson, Carlos R. Scherpenisse

The successful development of surface mining operations depends, amongst other factors, on the successful creation of final pit walls which offer long term structural stability. The achievement of such walls will be much more feasible if the mechanisms of rock mass deterioration in the mine are well understood, permitting the control and reduction of this deterioration (or damage). The role of drilling and blasting in causing damage is widely accepted but rarely fully quantified. It is also true that the dependence of rock mass damage on vibration levels is only incompletely understood and little accurate field measurement is routinely conducted in the mining industry.

Jan 1, 1998

By K Uenishi, H P. Rossmanith, N Kouzniak, A Daehnke

This contribution presents an introduction into that part of the field of elastic wave propagation which is relevant to blasting of boreholes and addresses briefly borehole breakdown and the formation of the fracture network around a borehole which ultimately leads to the disintegration of the rock mass. Phenomena of this kind are encountered in mining and quarrying. Numerical as well as experimental work referring to stress wave expansion from a detonating borehole is addressed.

Jan 1, 1998

By Clarence Zink

Aside from the mechanical properties and process of actual rock breakage, rotary drill bit performance is affected by several “post breakage” items: cuttings size, flushing air pressure, flushing air volume, cuttings load, drill hole geometry, etc. We all recognize that more efficient drilling creates bigger cuttings, more air pressure cleans the hole bottom better, more air clears the cuttings from the hole, and a better hole geometry allows cuttings to escape with a minimum of “regrind”.

Jan 1, 2006

By Detlef Sulzer, Winfried Rosenstock

"At the end of this century a great breakthrough in the field of blasting technology is finally going tobecome reality. That, in the true sense of the word, is the long expected and desired “HighTechnology Blasting”. So far trials have been carried out in Australia, Africa and Europe with remarkable results, that have been predicted by the authors. As a result, significant reductions of explosives and drilling expenditure are emerging for the future."

Jan 1, 1999

By Keith L. Bockelman

The Colowyo mine is a unique surface coal mining operation because it is a multiple seam pit. Using a combination of a shovel-truck and dragline operation, Colowyo mines 8 seams of coal to a depth of 400 ft. Over the past 3 years a number of operational changes have occurred, one of which is the implementation of blast casting. Through this implementation Colowyo has been able to eliminate over one million cubic yards a year, which would have had to be removed by the shovel-truck operation. This has also brought about a significant decrease in the stripping cost per ton within the dragline operation.

Jan 1, 1985

By J R. "Dick" Daniel

One of the more common tasks in blast management is the adjustment of: shot geometry, explosive energy, and shot timing parameters to achieve changes in blast outcomes and costs. Many of these shot parameters, once a delayed blast is initiated, are modified by the development of new free faces which change the original or static input values to dynamic values. These newly generated dynamic values are easily calculated and find use in fine tuning shot adjustments and in rationalizing blast outcomes in a systematic manner.

Jan 1, 1996

By Larry Schneider

In 1998, the Blast Vibration and Seismograph Section of the International Society of Explosives Engineers formed a working group to collect and compile a list of regulations limiting ground vibrations from blasting. The goal was to locate those countries, states, provinces, and cities that have such regulations, identify which governmental body enforces them, and determine what limits on ground vibrations are imposed upon the blasting operations. In the course of this study, data was collected from over 60 jurisdictions where peak particle velocity restrictions range from non-existent to very stringent. Some of the regulations were found to be based upon standards grounded in good science, while others possess little or no technical justification. This presentation will summarize the findings of the subcommittee, focusing primarily on what the limits are, which type of blasting operations must adhere to them, and to what structures they apply. The degree to which these regulations are based upon valid scientific and engineering research will be discussed. A listing of specific locations having such regulations and information about those regulations will be provide

Jan 1, 2000

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By Joshua Micah Hoffman, Catherine E. Johnson

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. One potential area from which future talent can be recruited is local student chapters. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements, there is a trend of job placement primarily in the engineering industry. Before the explosives industry can begin to compete with other industries, it should be determined what is drawing the students into these other fields. The work presented in this paper sought to better understand the collegiate student population from which a portion of future explosives professionals will emerge. This was done through the use of an anonymous online survey distributed to the student members of the International Society of Explosives Engineers, as well as, members of SEE student chapters. The survey contained questions about future job and career plans, ideal job placement, and expectations of salary. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry. This information can help steer recruitment activities and job offers. Through understanding what is incentivizing these students who have accepted or plan to accept jobs in other industries the explosives industry can better posture itself to be more competitive in recruiting from the collegiate talent pool.

Jan 1, 2014

By Stephen Mansfield

Analysing how accurately a blast design is implemented is one of the cornerstones of a successful operation, and critical for mine optimisation. This paper presents a concept that involves the collection and analysis of data for the five stages through which a blast transitions, from budget through to implementation.

Feb 1, 2020

By John Vynne, John Hutchings

There have been a number of recent technological advances in instrumentation for blasthole drills, and more specifically in drill monitoring and HPGPS guidance systems. Likewise, great strides have been made in the development of drill and blast software systems which are user friendly, while providing far greater capability to accurately design and monitor drill and blast patterns.

Jan 1, 2011

By Thomas L. Barkley

This paper describes an unusual design for a 12 foot diameter, 30 foot deep circular shaft shot in a close in urban environment less than 100 feet from occupied structures. It uses diagrams, video footage, and vibration results to describe a 3 deck, 17 hole burn round used to pull 17 feet in one lift.

Jan 1, 1994

By G Dean Barrett, Ed Jr Smith, Calvin J. Konya

The purpose of the project was two fold: 1. To determine whether Pyrodex, a propellant, manufactured by the Hodgdon Powder Company, could be used as a substitute for high explosives for presplitting in granite and other materials. 2. To determine if Pyrodex, a slow reacting propellant which produces no stress waves in rock because it reacts subsonically, could cause the rock to crack similar to the results achieved with high explosives.

Jan 1, 1986

By Scott Giltner, Allan Koski

Blasting is one of the lowest cost yet most critical parts of the mining cycle. This paper discusses the findings of an audit conducted on the blasting operation at an iron ore mine. The purpose of the audit was to review current blasting practices in order to identify opportunities for production/cost improvements. The approach taken in the audit was to observe general blasting practices, their related downstream effects and to compare current procedures to established best practices.

Jan 1, 2009

By Philip Barnhard, Lyman G. Bahr

By recording the arrival time of a pipe wall at evenly spaced intervals in a plane perpendicular to the pipe axis, application of the equations of motion permits calculation of the pressure of the explosive acting to accelerate the pipe wall. Data observed from various non-ideal explosives are presented, together with values of pressure to be expected from thermodynamic calculations.

Jan 1, 1981

By Michael Wieland

Three laboratory tests were developed for rating the wave-impact ruggedness of cap-sensitive explosives that are used for blasting in underground coal mines. Destructible pipe fixtures, called simulators, reproduce the shock wave or rift compression registered during the cross-hole wave interactions. The rift-compression fixture was modified to render quasi-static desensitization, when utilized with a remote air supply. Waves that were recorded near charge explosions show narrow pulses resembling underwater shock waves, followed by wide, weak humps, called rift compressions.

Jan 1, 1996