Search Documents

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

By M. A. Naimanbayev, Zh. A. Baltabekova, N. G. Lokhova

"Integrated utilization of natural resources using energy-saving and waste-free technologies is relevant around the world. This applies to such type of raw material as titanium-magnetite ore. Shortage of ilmenite raw materials in the Republic of Kazakhstan for titanium slag melting challenges the search of alternative titanium-containing raw materials, titanomagnetites in particular. At the same time there are deposits of indigenous titanomagnetite ores of huge reserves, which can become the complex raw material for production of iron, titanium and vanadium. Tymlay field in the South-Eastern part of Chu-Ili watershed is of particular interest, within the Karasay ore unit with iron content of 30,4 and titanium dioxide - 10%, and after beneficiation titano-magnetite concentrate contains Fe-52,4; TiO2-of 16,06%. Technology of titanium-magnetite concentrate ore-thermal melting was developed at Tymlay deposit producing hot metal and low titanium slag that can become the raw material for titanium production using chloride method. Slag produced in course of titanomagnetite ore-smelting consists mainly of alumosilicates and sodium silico titanates, magnesium and calcium titanates, titanium dioxide and lower titanium oxides. Following operations were carried out to improve titanium slag quality: slag sintering with sodium hydroxide; cake leaching with water to remove water-soluble impurities; to reduce the number of operations impurities leaching with hydrochloric acid was combined with pyrohydrolysis of titanic acid; rutile concentrate production (85% TiO2, 7,66% SiO2), silica removal by means of sodium hydroxide solution treatment, finally sellable rutile concentrate was produced with titanium dioxide 91-92% and silica 1,7 to 2,0% content. Based on research results technological scheme of titano-magnetite concentrate processing at Tymlay deposit was proposed producing hot metal and certified rutile concentrate, suitable for chlorination."

Jan 1, 2018

By Hillary Williams, Ronghao Li, Christopher Marion, Kristian E. Waters, Devin Hundt

"Zircon is an important mineral for ceramic, foundry, casting, and refractory applications; and it is the worlds primary source for zirconium. Zircon can also contain large and valuable proportions of other valuable metals, such as rare earth elements and hafnium. The Nechalcho deposit (Northwest Territories, Canad), is a hard rock REE deposit, which looks to recover zircon for its Zr and REE content. In this deposit, zircon is finely disseminated and associated with predominately silicate gangue minerals. Most of the work to date has focused on the beneficiation of mineral sand deposit, which typically remove silicate gangue minerals through physical separation steps. Therefore, the separation of zircon from silicate gangue, such as quartz, by flotation, has received little attention. This work used zeta potential measurements and microflotation experiments to understand the interaction between zircon and six different collectors (sodium oleate, sodium dodecyl sulphate, dodecylamine, SM 15, K-octyl hydroxamate and Florrea 7510). The results were compared with those of quartz. This study indicated that selective separation of zircon from quartz without the use of selective depressants or activators is likely challenging. The findings suggested sodium oleate and SM 15 only offered selective flotation of zircon in highly acidic conditions. Separation by the flotation of quartz is possible using sodium dodecyl sulphate, dodecylamine and K-octylhydroxamate. However, selective separation is highly dependant on collector dosage, for dodecylamine, and the selective activation of quartz, for sodium dodecyl sulphate and K-octyl hydroximate. Florrea 7510 offered poor recoveries for both zircon and quartz.INTRODUCTIONZircon (ZrSiO2) is a nesosilicate mineral which has a wide variety of applications, due to its hardness, opaqueness and resistance to heat and corrosion. Its major end uses are in ceramic, foundry, casting, and refractory applications (Bedinger, 2017). Zircon is also the most abundant zirconium (Zr) bearing mineral in the earths crust and is the principal economic source of Zr (primarily used in alloys for heat and corrosion resistance) and zirconia (ZrO2) (primarily used in ceramics) (Bedinger, 2017; Milnes and Fitzpatrick, 1989). Zircon forms in silicate melts and can often contain large proportions of other valuable metals such as rare earth elements (REE), and hafnium (zircon is the primary source of hafnium) (Bedinger, 2017; Belousova et al., 2002; Orlova, 2007). A common chemical formula showing the range of substitution in zircon is (Zr,Hf,Th,U,REE,Ca,Fe,Nb,Ta)(Si,P)O4 (Orlova, 2007)."

Jan 1, 2018

By James A. Finch

"Developed countries are in the midst of re-structuring education in minerals-related disciplines as raw materials, once vital to wealth generation, contribute progressively less to the economy. The changing circumstances mean institutions must justify mineral processing by new criteria. After considering what a mineral processor needs to know the ways to deliver are considered. Taking twenty graduates per year to illustrate, one institute could justify this number as a program in a department or school (of whatever grouping of disciplines). A strong research component would make the package additionally attractive. Divide among four institutions and mineral processing is best served in a research centre with delivery taking advantage of multi-centre and distance learning opportunities.INTRODUCTIONThis is one of five plenary lectures at the Congress. I may have preferred a technical subject, as that is what occupies most of my thinking hours, but it is reasonable as an academic that this topic should come to one of us. The fact the topic has not been high on my agenda may provide one advantage: that I can suggest directions free of pre-conceived notions, just as when reviewing the background to a technical article the temptation to select in support of one?s interpretations is resisted. The trick will be to add something new.One reading of the title seems to query whether mineral processing education has a future. (I will refrain at this juncture from defining mineral processing and assume for now we share an understanding of the term.) The proximity of natural and human resources led to the Industrial Revolution and the interaction continues to stimulate and sustain industrial and economic development in many parts of the world. The search for raw materials has historically played a key role in opening frontier areas, with undersea and outer space next. The reason is obvious: raw materials along with food and energy underpin society. Thus mining will remain part of human activity along with the need to pass on the knowledge and skills.What happens over time is resource relocation. Raw materials become exhausted in one area to be replaced by sources elsewhere; the demand for some materials lessens while growing for others. Educational institutions can find themselves with the wrong geography or with staff focussing on the wrong subjects. When this happens the restructuring produces much discussion. This is where we are in parts of the world. Japan, Western Europe and the United States are the prominent examples (Dowd, 1998; Flemings and Suresh, 2001; McDivitt, 2002). Mineral processing is becoming a series of courses in related disciplines: resource engineering, environment engineering or materials engineering. The start of the transition is evident in Canada and Australia, perhaps earlier than expected given the contribution of raw materials to their economies. A common backdrop in the developed countries is social pressure to reduce the impact of the ?untidy? aspects of life, and that includes mining. (This is not new: in classical times the mine face was the preserve of slaves and convicts.) These values are exportable, potentially affecting recruitment into mining schools everywhere."

Jan 1, 2003

By V. K. Gupta

Selection of mill size for reducing a feed material of a given size to the desired product size is generally based on the specific energy estimate obtained from Bond test. Over the last thirty years or so, an attempt has been made to develop a more accurate and powerful alternative approach based on the characterization of the particle breakage kinetics and material transport through the mill over a range of operating conditions of interest and correlating the degree of size reduction achieved with the net specific energy input to the mill. Particle breakage kinetics are described in terms of the specific grinding rate and breakage distribution parameters for the individual size fractions. Precise estimates of these parameters and the net energy input to the test ball mill (a laboratory or pilot scale mill) are important for development of desired energy-size correlations. In this context, three tasks are important: (a) preparation of the feed charge, (b) design of batch grinding experiments and (c) computational technique used for estimation of the breakage rate and breakage distribution parameters. This paper highlights several aspects of these three tasks that have been overlooked by researchers working in this field, and describes a more appropriate approach for estimation of model parameters and specific energy input. Several examples are included based on the data available in the literature and those generated in our laboratories to illustrate important points.

Sep 1, 2012

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003

By H. J. Schulze

From a colloidal science point of view (Schulze 1984, Nguyen & Schulze, 2004) five micro-processes are responsible for successful particle-bubble formation: the approaching of the particle to the liquid-air interface, the thinning and rupture of the intervening liquid film, the expansion of the three phase contact perimeter, the generation of sufficient large capillary force to stabilise the aggregates and the transport process of particles into and within the froth layer. Flotation reagents influence mainly the thinning and rupture of the intervening liquid film between particles and air bubbles, the expansion of the three phase contact after the rupture of the liquid film and the stability of the aggregates against external destruction forces in the flow field. But it exist also a non-negligible influence on the approaching of particles to the bubble surface during the encounter process and on their passing over into the froth layer and the froth stability.

Jan 1, 2003

By J. A. Sweet

The issues facing graduate training in the mineral processing industry are not too different today from those that prompted the initiation of the Anglo American Platinum Graduate Development Programme (AGDP) in 2002. Graduate metallurgists in South Africa enter the industry from different undergraduate programmes at various tertiary institutions, and so the knowledge and skills of the young graduates varies. Further, the geographical expansion of the industry combined with the downsizing of business units means that there are fewer opportunities for young graduates to be mentored through their first few years on site. Anglo American Platinum chose to address these issues by implementing an intensive, structured graduate training programme for all their new metallurgical graduates, known as the AGDP. The first two years of experience of the AGDP, from the viewpoints of both graduates and lecturers, were presented to the mineral processing community at the IMPC in Turkey in 2006 (Sweet et al, 2006). From the beginning, the programme was structured in a modular fashion to include a basic technical ?toolbox? including statistics, the scientific method and sampling protocols, while the mineral processing content comprised advanced learning in comminution, classification and flotation (later extended to include hydrometallurgy). Technical communication ? both written and verbal ? was included from the start. The programme was focussed very strongly on site work (?learning by doing?), with a major integrated site campaign conducted and analysed by each cohort. In 2012 the AGDP will accept its ninth cohort into the programme. This paper describes how Anglo American Platinum and the University of Cape Town have developed and adapted the programme over the last few years, in response to the challenges of the global recession, skills retention, and the changing operational needs of the company. The programme, which was drawn up to accommodate around 15 concentrator-only graduates, now accommodates 35-40 concentrator, smelter and refinery graduates annually. The programme has also been modified to facilitate new graduates spending most of their first year on the operations. The benefits of the programme for Anglo American Platinum have been tangible, and will be discussed in the paper. Keywords: graduate training, technology transfer

Sep 1, 2012

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth's crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By C. Martinez, S. Helle, M. Pincheira

We studied the feasibility of automated mineralogy to discriminate between tennantite and enargite, the main sulfosalts found in the Rio Blanco deposit, Codelco-Chile, in order to predict the content of minor elements (As, Sb, Ag, Pb, Zn) that impact on the process and concentrate prices. The identification of these minerals is feasible using traditional microscopy, however not possible by automated mineralogy. This drawback prevents comparing the databases generated in the past by means of conventional microscopy with the information obtained at present by QEMSCAN. To differentiate enargite from tennantite the mineral composition of both sulfosalts was studied by electron microprobe. The presence of associated minor element contents of about 8% zinc in tennantites and not exceeding 0.07% in enargites were used to modify the SIP database of QEMSCAN to enable the quantification of these phases in samples of head, residue and concentrate coming from As-bearing domains of the deposits. Detection limits allowed to determine the mineral species in the head, concentrate and residues. The integration of methodologies such as automated mineralogy and microprobe can be used successfully to quantify the presence of some ore forming solid solution.

Jan 1, 2014

By D. Berman, A. Brodt

"Delivery of all volume of mined mass on the terrestrial surface results not only in irrational power expenses on moving of huge volumes of dead rock as a part of initial raw materials (especially vertically) on long distances, but also necessities of storing tailings in open-air. Thus, in bowels of earth, huge volumes of the developed space are formed. However, the nature doesn't suffer emptiness. As consequence, through the process of underground mining works, in earth bowels starts intensive development of rocks dislocation processes involving subsidence of terrestrial surface, and with it, begins irreparable damage every objects which are on that territory. Highly effective new methods of underground concentration of the various minerals, which deliveries of only target component on terrestrial surface integrally connected with transport process in stream and subsequent deliveries to destination in continuous mode by the long distance hydrotransport, allow not only to eliminate a construction of concentrating factories on the surface, but also storing of tailings of concentration process on open-air preventing dislocation of rocks, thanks to operative placing tails in the underground developed space. Surely, the main problem in the development of such gravity dressing technology is the problem of finding the optimal formula for the heavy liquid that will fill such system in close connection with the procedure of its full regeneration. The requirements for such liquid are being non-toxic and cheap. This question was solved successfully."

Jan 1, 2014

By Amir Hajizadeh Omran, Mehdi Irannajad, Sima Mohammadnejad, Fardis Nakhaei

"This study presents an experimental program performed to investigate the effects of flotation variables including gas flow rate, froth depth, slurry solids percent, frother/collector dosage and pH on the froth bubble size during desulfurization of an iron ore. These conditions were varied using a central composite design (CCD). Image analysis techniques have been developed and used successfully to characterize the froth bubble size. Results of the CCD experiments showed that the flotation variables have different effects on the froth bubble size. The froth height, air flowrate, pH and solid content had the most important influence on the froth bubble size. The interaction between the collector-frother, pH-collector, frother-air flowrate, solid content-froth height, pH-froth height and solid content-pH were also significant. Process state can be accurately deduced from the froth surface appearance, providing a convenient way to quantify the parameters as a function of the process control. INTRODUCTION Flotation processes are subjected to a wide variety of process disturbances, some of which are made by the change in mineral features and others to variation in operating procedures. Feed and air flow rates, densities, size distributions and shapes of particles, surface properties, and reagent dosages and compositions can all change, often with significant effect on the performance of the plant (Moolman et al., 1996a). Flotation process efficiency is governed by the wettability of the solid as well as the surface tension at the liquid-gas. Both of these properties are influenced by operational conditions encountering in a flotation process. The structure of froths developed on the pulp surfaces of flotation cells has a remarkable effect on both the grade and recovery of minerals in the concentrate (Shean and Cilliers, 2011)."

Jan 1, 2018

By Fengming Li, Baocheng Song, Yuemin Zhao, Hailin Dong, Liping Peng, Chusheng Liu, Chenlong Duan

The large-scale vibrating screens with high processing capacity and efficiency are now in great demand in the mineral processing industry of China. However, as the equipment is always suffering from the strong external harmonic exciting force, the inertial force and the impact from the minerals, the fracture of the beam and the crack of the lateral plate are easy to occur, which has a negative effect on the reliability of the equipment itself and the industrial production. Considering the essential high reliability of the equipment, a new large-scale vibrating screen with duplex statically indeterminate mesh beam structure (VSDSIMBS) was developed. The natural characteristics, namely, the natural frequency (or the modal frequencies) and the natural mode, and the dynamic characteristics of the VSDSIMBS were obtained by the modal analysis and the harmonic response analysis. In addition, the dimensions and the constructions of the statically indeterminate plate and the mesh beam were chosen as the design parameters, to which the sensitivity of the whole mass, the maximum deformation and the maximum stress of the duplex statically indeterminate mesh beam structure (DSIMBS) were summarized for the optimization of the DSIMBS. Now the large-scale VSDSIMBS is being well used in China.

Jan 1, 2014

By Valentine Chanturiya, Irina Khabarova, Maria Ryazantseva, Igor Bunin

"XPS investigations of the influence of HPEMP - treatment duration on the surface composition for natural chalcopyrite and sphalerite are described. HPEMP is a video pulse with a nanosecond front lasting between 5 and 10 ns. The electrical field component can reach 30 kV, whereas pulses repetition frequency is 100 Hz. In general, the formation of metal-deficient surfaces, polysulphides or elemental sulphur and oxides/hydroxides, were determined during the treatment for both sulphides as well as the essential differences of the way of mineral surface transformation during the treatment. The chalcopyrite surface shows the formation of elemental sulphur under the HPEMP treatment at 103 pulses while appearance of unstable sulphite species was detected at the chalcopyrite surface within 5 seconds (0.5•103 pulses) under the same treatment conditions. The results indicate that the quantity of adsorbed water (at.%) is changed considerably during the HPEM - treatment depending on treatment duration for both minerals. The concentration of water onto the chalcopyrite surface decreased during 30 seconds (3•103 pulses) of the HPEMP - treatment and it rose after the treatment at 5•103 pulses. The inverse dependency was obtained for sphalerite surface. Single mineral flotation tests have shown the significant increasing of the minerals recovery."

Jan 1, 2014

By Lj. D. Andric

Development of modern devices for mechanical and mechanochemical materials activation has been dated since the beginning of last century. Rapid development of high-energy mills that are different in type, size, design and performances, has been occurred during the last four decades. Because of complete understanding of mechanical processing, entire knowledge of theoretical principles of high-energy mills is necessary. These principles are main causales of process that are happened in materials during the mechanical activation. This paper is occupied by theoretical principles of operation of high-energy mills. Conventional high energy mills with balls, high-energy planetary mills and high-energy vibrational mills are particularly considered in the paper.

Jan 1, 2014

By S. P. Nagaeva, O. U. Poperechnikova, A. V. Kuptcova

"In case of free gold presence in ore, there is always problem of a choice between the gravity-flotation and gravity separation flowsheets. Study of morphology of gold being extracted by different methods allows to find the most efficient solution. One of the latest methods of gold concentration for wide range of grain size (-0.8+0 mm) is a flash flotation. The paper presents comparative testing results of flash and centrifugal separation.The goal of the studies was to determine process and flotation parameters of flash flotation. In case valued minerals are soft if compared to host rock, such minerals tend to concentrate into circulating load of grinding circuit. Thus, valued minerals can be overground, and in turn, will result in low extraction in flotation circuit. Integration of flash flotation operation into process flowsheet has been evaluated. Flash flotation operation can be successfully used not only for gold but also copper, lead, nickel and silver minerals.With low-sulphide ores being a case study under laboratory conditions, various flotation (impeller rotational speed, air flowrate) and process (pulp density, collector consumption, frother consumption, time of flotation) parameters were studied in view of its impact on gold flash flotation. Experiments were carried out under laboratory conditions using special pneumatic mechanical flotation machines.INTRODUCTIONGravity separation is used for extraction of coarse gold before cyanidation and before flotation of polymetallic ores to increase gold total recovery into gravity copper and lead concentrates.Benefit of the flash flotation is efficient recovery of coarse gold carrier particles (sulphides) thus preventing its regrinding and, as a result, low recovery. Furthermore, combination of flash and conventional flotation results in final tailings that do not require further cyanidation.Combined gravity-flotation flowsheets are designed for concentration of ores containing gold within thewide range of grain sizes (see Table 1)."

Jan 1, 2018

By V. A. Zhilina, I. V. Shadrunova, O. E. Gorlova

"The aim of the study is to develop and scientifically justify a new adaptive approach to the separating processes of deep and complex processing technogenic mineral raw materials. Technogenic mineral resources as a waste of mining and processing industry are mostly complex objects that have specific features of material composition and technological properties and make it processing ineffective with traditional schemes of mineral raw materials enrichment. Mineral wastes are regarded in this study as a complex object with a large number of signs in conditions of uncertain environment and object. However, adaptation is regarded as the process management system’ adaptation to the specific the properties of the object and the environment that has several hierarchical levels corresponding to different stages in the management of complex object. An adaptive approach is considered as a methodological basis of multivariate schemes for opening the mineral resources and creating mechanisms that could transfer these potential technogenic resources to the actual that significantly expand the mineral resource base of the country's black, coloured, rare, noble metals and construction materials. In this case, potentially the solution to the most pressing social and environmental problems associated with the adverse effects of past economic activity simultaneously with the commercial objectives. This approach to the wastes mining and related processing manufacturers meets the core idea of sustainable development as the balance of interests of State, society, business, private enterprise and each person in the areas of rational use of resources, economic efficiency and environmental safety. On the example of metal-containing raw materials in the form of slags of ferrous and nonferrous metallurgy, ferrous metallurgy sludge, mature fine tailings, the application of adaptive approach illustrates to the development of technologies of its deep and complex processing as phased, thoughtful movement from a comprehensive study of technogenic raw materials to build optimal topologies of technological schemes for processing the mineral wastes. INTRODUCTION Involving the Russian economy in the system of global economic relations significantly changes the nature of the country's competitiveness in the development of the world market and urgently requires competent management of its own natural and mineral resources. The latter at the present time in real economic processes cease to be a passive material foundation and become the producing basis in the production processes in the status of so-called natural capital. Introduced in the field of economic theory at the end of the 20th century, this term means both the flow of natural services and real natural resources. Consequently, natural objects, which act as natural resources of a certain production, today must necessarily be evaluated in a strategic sense. Modern standards of sustainable development presuppose that the economy should equally be oriented to balance the interests of the state, society, business, individual enterprise and each person in the spheres of rational use of resources, preservation of healthy ecosystems, ensuring well-being, high quality of life and environmental safety of not only the current generation, but also respect for the rights of future generations, that is, intergenerational equality. Most types of minerals are classified as non-renewable resources, therefore resource-saving in the sphere of mineral and raw materials complexes is one of the most important factors-indicators characterizing the degree of approximation to the model of rational subsoil use, and, consequently, sustainable development (State Report, 2017)."

Jan 1, 2018

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By Chris Plackowski, Bruckard. Warren J., Anh V. Nguyen

"Enargite is a significant penalty mineral in the copper industry and its separation from many copper sulfides by flotation is difficult. The separation may be crudely achieved using selective oxidation techniques or through the use of pulp potential control. This paper summarizes our latest contributions to a better understanding of enargite surface electrochemistry and hydrophobicity. Oxidation, roughness, hydrophobicity and species formation on the surface of natural enargite were examined by a novel experimental approach that combines electrochemical techniques, atomic force microscopy, X-ray photoelectron spectroscopy and droplet evaporation tensiometry. It allows for synchronized electrochemical control and examination of the oxidative surface morphology, speciation and hydrophobicity of enargite at pH 4 and pH 10. At low pH, surface layer formations consisting of metal deficient sulfide and elemental sulfur were identified associated with a limited increase in roughness and heterogeneous distribution of surface species produced by initial rapid dissolution of Cu, followed by diffusion limited surface layer deposition. At high pH, a similar diffusive mechanism associated with oxidation products consisting of copper sulfate and hydroxide and a significant increase in surface roughness were established. Receding contact angle measurements showed no significant difference in the contact angle on a surface oxidized at pH 10 and the freshly polished surface. Contact angle increased from 46° on the polished surface to 59° after oxidation at pH 4. Competing effects of hydrophilic copper oxides and hydroxides, and hydrophobic species of elemental sulfur on the mineral surfaces under oxidizing conditions at pH 4, and the change in surface roughness at pH 10, contribute to the changes in enargite hydrophobicity under electrochemically-controlled oxidation conditions. Most likely, both surface species and surface roughness produced by oxidation are critical to the changes in the wettability of enargite and other sulfide minerals."

Jan 1, 2014

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018