Search Documents

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By S. Mohanta

In composite washeries optimization of operating parameters to achieve maximum clean coal yield at the desired clean coal ash level is a major problem. This problem is more acute in countries like India, which have predominant reserves of difficult-to-wash coals. The constrained operational parameters of washing for some equipments make it more severe. In addition to this, the dependence of separating performance of different equipments upon various variables aggravates the situation. Here an attempt is made to find a numerical solution to get maximum yield and minimize the difference between the actual and the theoretical yield. The solution is arrived through constrained non-linear optimization of a multivariable objective function that utilizes spreadsheet tools; the method accommodates any number of source coals or washing size fractions. By using a designed Ep value the predicted yield of composite clean coal has been calculated and the yield is optimized subject to constraints on both the ash and specific gravity. It is shown that operational constraints of different washeries in the composite plant that utilizes gravity separation methods can also be over-come. The technique offers the coal preparation engineer an effective and straightforward method for determining the optimum cut-points of separation for different coals or blended coals to obtain maximum product yield at a specified level of ash content.

Jan 1, 2014

By M. Evertsson, K. Bhadani, E. Hulthén, M. Bengtsson

"Modelling and simulations for mineral processing plants have been successful in replicating and predicting predefined scenarios of an operating plant. However, there is a need to explore and increase the potential of such simulations to make them attractive for users. One of the tools to increase the attractiveness of the simulations is through applying optimization schemes. Optimization schemes, applied on mineral processing simulations, can identify non-intuitive solutions for a given problem. The problem definition itself is subjective in nature and is dependent on the purpose of the operating plant. The scope of this paper is to demonstrate two optimization schemes: Multi-Objective Optimization (MOO) using a Genetic Algorithm (GA) and Multi-Disciplinary Optimization (MDO) using an Individual Discipline Feasible (IDF) approach. A two stage coarse comminution plant is used as a case plant to demonstrate the applicability of the two optimization schemes. The two schemes are compared based on the problem formulations, types of result and computation time. Results show that the two optimization schemes are suitable in generating solutions to a defined problem and both schemes can be used together to produce complementary results. INTRODUCTION The comminution process for a mineral processing plant consists of multiple crushing and classification stages and aims to produce fine material to liberate ore from the minerals. The modelling and simulation of such processes are well established using static process models (King, 2001; Napier-Munn et al., 1996). A recent development in the dynamic modelling for such processes has shown further increase in fidelity compared to the static process models (Asbjörnsson, 2015). The developed simulations can be utilized to design, operate and control mineral processing plants based on the requirements of users (Bhadani et al., 2017). Typically, the requirements in the operation of the comminution process are conflicting in nature, as for instance, reduction of power draw by process units, maximization of production of fine materials, and increasing utilization of the process units. These conflicting requirements leads to a Multi-Objective Optimization (MOO) problem to operate a mineral processing plant. The MOO problems are normally referred to as non-linear problems and its fundamental understanding with respect to process behaviour is difficult to achieve."

Jan 1, 2018

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

"Grinding has a significant economic impact on ore dressing/processing, therefore the sizing of mills has an outstanding role.In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the post-grinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature (up to 100 ºC) in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances (grinding in alkalis medium at different temperatures) and allowing a more precise mill sizing. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids with different temperatures (water, alkali). This paper presents in detail the equipment, the conditions (parameters) of the testing process for wet and alkaline grinding, the measuring results and the conclusions."

Jan 1, 2003

By L. C. Zhou

The floatability of andalusite and associated minerals are studied and their action mechanisms of andalusite and associated minerals with collector alkyl benzene sulphonate are also studied. Through the mensuration of electrical potential and the infrared spectroscopy, as well as desorption tests, it is confirmed that the interaction of andalusite with sodium dodecyl benzene sulphonate (SDBS), is in addition to physical adsorption, but also is chemical adsorption. The study results of the pure minerals are used for the flotation of actual andalusite mineral. By flotation from contain-ing 45.68% andalusite ore, the fine andalusite concentrate is gained which Andalusite grade is 85.88%, containing Al2O355.29% and Fe2O3 less than 1.5%.

Jan 1, 2014

By Z. Hu

A complex polymetallic sulfide ore in Yunnan, China, has various valuable minerals, which are Chalcopyrite, Galena, Pyrite, Gold, Silver, and Magnetite. A reasonable new flowsheet with a bulk flotation and a flotation separation of sulfide minerals that are Chalcopyrite, Galena, and Pyrite was carried out at first stage. After that tailings were treated by low intensity magnetic separation to achieve magnetite concentrate. A high Pb concentrate assaying 60.00 percent Pb at total recovery of 75.71 percent with 40.50 g/t Au and 1390.00 g/t Ag, a final high Cu concentrate assaying 24.45 percent Cu at high recovery of 92.03 percent and a magnetite concentrate assaying 60.78 percent Fe at recovery of 33.61 percent with 18.45g/t Au and 234.99 g/t Ag, are obtained. The total recovery of Gold and Silver in Pb concentrate and Cu concentrate reached 71.63 percent and 67.32 percent, respectively. It is shown, that this new flowsheet could realize efficient recovery for all of the valuable minerals in the ore and is easy to be industrialized. Keywords: bulk flotation, magnetic separation, polymetallic sulfide ore, depressant

Sep 1, 2012

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By U. A. Peuker, T. Mütze, F. Shayo, A. Wikedzi

"Buzwagi Gold Mine (BGM) is operated by Acacia Mining and located in the Lake Victoria Goldfields of central Tanzania. The mine treats a sulphide copper-gold ore to produce gold in form of doré bars and a concentrate containing gold, copper and silver. The BGM comminution circuit includes a primary crushing stage with a gyratory crusher and two grinding circuits using a Semi-Autogenous Grinding (SAG) mill and a ball mill. Currently, the grinding circuits are inefficient in achieving the aspired product fineness of xP,80 = 125 µm even at low to normal throughputs (450-600 t/h). An optimization study of the circuit performance was conducted to improve product fineness through circuit surveys, experimental lab work and simulations. The analysis of survey data revealed inefficient grinding operation characterized by ball mill product (xP,80 > 400 µm) coarser than designed and higher hydrocyclone cut sizes (xT > 200 µm), too. In MODSIM several options were simulated such as reduction of vortex finder and apex diameters, reduction of SAG screen aperture, and modification of cyclone feed density. An improvement of product fineness could be achieved by simulation of the cumulative changes but it was also concluded that the current equipment cannot achieve the target. Further simulations showed that a second ball mill might help to achieve the desired fineness as well as an increase of grinding throughput by up to 26 %. INTRODUCTION Simulation of comminution, particularly grinding and classification, has received great attention for many years, due to the fact that the unit operation is by far the most important both in terms of energy consumption as well as overall plant performance (King, 2001; Wills et al., 2006). The use of simulation is advantageous due to low cost as well as its ability to consider many variables simultaneously. Moreover, there are some benefits for optimizing grinding operations by simulation like decreased unit operating costs, increased capacity, and improved performance of downstream processes due to improved feed size distribution. This paper presents an optimization study for the grinding efficiency at Buzwagi Gold Mine. This was achieved through three full scale circuit surveys, lab work and simulations with MODSIM."

Jan 1, 2018

By B. Das

The processing of banded iron ore by direct anionic and reverse cationic flotation to produce pellet grade concentrate is investigated. This low-grade iron ore, known as banded hematite quartzite (BHQ) contains 41.8% Fe, 41.5% SiO2, 1.2% Al2O3, and 0.5% LOI. The flotation behavior of BHQ is studied by varying the effect of concentration of collector, frother, dispersant and pH. Oleic acid and dodecylamine are used as the anionic and cationic collectors respectively. The parameters that gave the best results in cell flotation are utilized in 100 mm diameter flotation column. All the results are compared with regard to the iron grade and recovery in concentrate. It is observed that, anionic collector with dispersant dosage of 220 g/ton, at pH ~8.5 is selective and yielded a high-grade iron concentrate with low silica as impurity. Also, it is possible to achieve an iron concentrate with 64% Fe at 30-37% weight recovery. The characterization studies of the BHQ ore using X-ray diffraction (XRD) technique and liberation analysis with QEMSCAN® are carried out. The sample contains 58.8% hematite and 37.7% quartz and the liberation of hematite particles are found to be 90.3% in -25 µm size. An alternative statistical modeling approach called response surface methodology was also undertaken to optimize the operating parameters in order to maximize the iron grade and recovery. The predicted results by the model are in agreement with the experimental values.

Sep 1, 2012

By Z. H. Zhang

Shizhuyuan is a world-class WO3, Mo, Bi and CaF2 poly-metallic deposit; it has rich reservation, but great difficulty in ore?s processing; thereby, for many years, it has been the target problem of beneficiation technologies. This paper, while briefly reviews its main scientific and technological advancement, pays special attention to the complete set of new technology and technical index achieved in recent years, which is characterized by using full-floatation flow-sheet as the backbone flow-sheet, explores some key factors influencing tungsten floatation, and presents a brief introduction to such new equipment as flotation column and comprehensive utilization of fluorite.

Jan 1, 2014

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By Y. C. Liu

Arsenic bearing copper-gold ores deposit have been found in most areas of China, especially in southwest. Due to the very closed association between arsenic, copper and gold, conventional flotation and cyanide leaching process may not give positive results. An arsenic bearing copper-gold ore in Sichuan province ,with gold grade of 10.12 g/t, 0.6% Cu and 0.14% As, is characterized by superfine grains with -40 microns fraction accounting for 70.9% and the gold enwrapped mainly by pyrite and tennanite accounts for 34.31%. Arsenic in this ore occurs in isomorphism, deposited in tetrahedrite. The ore was processed primarily in two stage flotation to get copper bearing gold concentrate and pyrite bearing gold concentrate respectively, and sequentially processed by leaching. Under the pressure of 300 KPa and 110~115 ?, the copper-gold concentrate was leached by an oxidizing and catalyzing leach agent then copper and gold were separated from each other in leach solution. The pyrite bearing gold concentrate was processed by cyanide leaching with the leach residue as sulfur product. The test results showed that copper recovery was up to 88.89%, gold recovery up to 89.18% and sulfur recovery up to 92.64%.

Jan 1, 2014

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS) excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a of which are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 20 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction.Pure mineral phases and mineral mixtures were used for the flotation tests. As opposed to current knowledge, the results were reproducible with technical flotation machines."

Jan 1, 2003

By H. R. Manouchehri

Sustainable development requires the optimal use of natural resources and recycling of the wastes. In fact recycling is the final productive use of obsoletes. ELVs, obsolete appliances and industrial wastes have become important resources for production of iron and steels, non-ferrous metals, and composites. Within shredding plants, these obsoletes are firstly shredded to the pieces and then processed to recycle different materials, especially ferrous and non-ferrous metals for metallurgy. Traditional and new developed mineral processing technologies are nowadays used for recycling different materials from waste effluents. Shredding and separating plants are currently recycle the wastes by make use of different technologies to mainly produce raw material for metallurgical application. However, other non-ferrous components are also treated for energy conservation and protecting environment. Currently, recovery in shredding and recycling plants maximises to 75% and about 25% of the feed is land-filled. However, recycling rate must be increased in due to the economical, environ-mental and social concerns. A comprehensive study for recycling, with especial focus on ferrous metal recovery, was sup-ported by Swedish Environmental Agency (MISTRA) to look at possibilities to increase the recycling rate and to reduce the amount of disposal. Part of this study was dedicated to study the shred-ding plant facilities and to look for possibilities to improve the quality and quantity of the shredding product streams. The aims were to improve the quality of ferrous scrap (apparent density > 0.9 and Cu<0.25%) for iron and steel production as well as having better quality for non-ferrous metals through the recycling schema, and finally to treat the shredder residue (SR) to recover metals and plastics to reduce the disposals. This paper summarises the results of sampling and conducting separation tests for improving the recovery of the ferrous and non-ferrous metals. The results indicated to be possible to obtain high quality ferrous scrap at recovery of 88%. However, the total recovery for metal scrap has reached 93%. Furthermore, test results on fine, P< 8mm, shredding residue (SR) showed promising prospect in recovery of metals and protecting environment by physical separation, i.e. electrical separation technique.

Jan 1, 2014

By S. N. Sahu

Attempt was taken in this study to explore the misplacement phenomena in binary mixture in solid-liquid fluidisation system. The binary mixtures of hematite and quartz particles at different sizes were taken. The closed size range particles were taken to minimize the size and shape effect in fluidization. As both the minerals have appreciable density difference, the separation of both minerals with closed size range has an advantage. The experiments were conducted in different permutation and combination of different sizes of binary mixture to observe the fluidization phenomena. The samples were taken at different heights in fluidized zones and analyzed the distribution of particles of both minerals. The fluidization characteristics were evaluated with respect to operating and design parameters. It has been observed that when the terminal velocity of quartz and hematite particles is same or near to each other, then misplacement is significant. In general, the segregation index value is near to one, complete segregation takes place whereas this value is near to zero, complete mixing takes place. The experimental data were used to find out the segregation index for different size ratios of quartz and hematite particles and the values are within 0-1. When the size ratio is 1 or less, complete segregation takes place whereas this ratio is within 1.0-1.4, partial mixing takes place. Similarly, when the size ratio is within 1.4-2.0, complete mixing takes place whereas this ratio is within 2.0-4.6, then it moves towards complete segregation in inversion manner. Keywords: particulate fluidization, misplacement zone, bed expansion, terminal velocity, mixing characteristics, segregation index

Sep 1, 2012

By Kamalendu Bhunia

With the progressive depletion of known resources of good quality coal and minerals as well as the increasing demand of these minerals by different user industries, the emphasis has been shifted all over the world from selective mining to bulk mining followed by up- gradation to obtain the required quality of concentrate. The column flotation cell is one of the alternatives to reduce the gangue content of fines because of its inherent characteristics viz. easier to operate, low space required, no moving parts etc. A laboratory flotation column is used to conduct experiment. Present work has been undertaken to observe the effect of process variables (gas flow rate, feed/slurry flow rate, and frother concentration) on gas dispersion parameters (gas holdup, bubble surface area flux) in collection zone and to explore the effect of feed (slurry) inlet orientations and gas flow rate on column?s metallurgical performance. The effects of solid particle concentration, size and type (hydrophobic and hydrophilic) of solid on gas dispersion parameters have also been investigated. Test work has been performed in a continuously operating Perspex column (10 cm in diameter and 168 cm in height) using coal, sphalerite and dolomite as solid. Gas hold-up has been measured by phase separation method and mean bubble sizes are estimated from a drift flux analysis. The influence of operating parameters on bubble surface area flux has been discussed. It is observed that gas holdup in collection zone is affected by air as well as feed flow rates and also solid?s type. It is also found that addition of solid decreases the gas holdup and rate of decrease in gas holdup increases when solid concentration increases and particle size increases. Increase in gas flow rate increases recovery in collection zone due to increase in number of bubbles per unit volume of the column. From the experimental results it is evident that cross-current orientation of feed inlet shows slightly better metallurgical performance compared to other orientations. Keywords: column flotation, gas holdup, drifts flux, bubble size, bubble surface area flux, hydrophobicity, and recovery

Sep 1, 2012

By P. S. Dash

With implementation of stringent environmental regulations, ultra clean coal technology development programs have gained significant importance worldwide. As far as Indian scenario is concerned, most of the coals present in India are of drift origin and low grade, containing high mineral matter varying from 15% to greater than 50%. The inorganic or ash constituents of Indian coals are finely disseminated through the organic or carbonaceous constituents so, that commonly used physical beneficiation techniques are of only limited value in affecting separation. Chemical processes involve addition of chemicals, which react with the mineral matter and allow its easy removal. The present study envisages the effect of aqueous alkali leaching followed by acid washing on the removal of mineral matter from two different captive coals of Tata Steel at elevated temperature and pressure. The experiments are conducted at desired conditions using a bench scale pressure reactor set up having proper data acquisition and control system. The research study revealed, that it is possible to reduce the ash content up to 70% by this method. The alkali content of the product clean coal does not increase whereas the silica and alumina content reduces by nearly 58% and 62% respectively. Significant reduction in the phosphorus content is observed after the acid treatment. The crucible swelling number of the feed coal improves after the treatment. The mechanism of demineralisation was evaluated by analyzing the coal samples before and after the alkali and acid treatment using scanning electron microscope (SEM). Because of the acidic nature of the silicates and aluminates, they dissolve into the NaOH solution and form sodalite. Sodalite is partially soluble in the alkali solution. The hydrates formed during alkali treatment are partially removed due to acid wash. This study in overall provides an insight into possible alternative methods of beneficiation for removal of ash from high ash Indian coals.

Sep 1, 2012

Separation performance of a Floatex Density Separator (FDS) has been studied both experimentally and theoretically. Experimental results reveal that at a lower bed pressure the FDS acts like a classifier. Higher bed pressure is required to attain the concentration effect as proper development of suspension density occurs under these conditions. It is seen that the size or density alone is not able to describe the partition fully. The terminal settling velocity, which includes both the size as well as the density of the particle can be a useful descriptor of separation in a FDS. While a narrowly distributed feed offers better performance of a FDS, a wide size distribution of feed results in large scatter in the terminal settling velocity distribution and renders the separation difficult. The closely sized feed enhances the density effect in concentration. A higher teeter water flow rate also helps in carrying larger-lighter particles to the overflow by increasing the cut off terminal settling velocity as it increases the net upward force. A detailed description of separation performance in a Floatex Density Separator has also been established from theoretical considerations. Separation performance of the separator is described using a simple slip velocity model. The model has been validated com-paring the predicted FDS performance results with those experimentally measured under widely different operating conditions.

Jan 1, 2014