Search Documents

By V. F. Petrov

Cyanide is widely used gold lixiviant for hydrometallurgical processes. The resulting tails contain complex toxic compounds. With reference to this, the protection of the environment should be the major issue. A complete detoxification of cyanides before disposal, a partial detoxification to the allowable concentrations and a disposal of tails at a polygon followed by the detoxification of excess water into the environment are offered as an environmentally friendly way of disposal. However, a complete detoxification of the cyanidation tails does not give the required results due to the presence of toxic compounds, cyanides and thiocyanates in tailings ponds. This is due to adsorption-desorption process occurring between solid and liquid phases. A partial detoxification is used to down cyanide to the allowable concentrations, which are safe to the environment. The storage of tails without detoxification is mainly used at low concentrations of toxic compounds in the disposed tails. With reference to this, water recycling is practiced by Russian plants in order to reduce as much as possible or almost eliminate toxic effluents into the environment. Fresh water is applied if necessary and to make up for water losses, with 8-12% of total water supply. This allows for the stability of water balance and the decrease of consumption of the reagents applied. The conditioning technologies of water recycling followed by regeneration of free cyanide and metals recovery as saleable concentrates are specially developed due to adverse impact of water recycling on gold recovery processes due to high concentration of base metals (copper). These technologies are also profitable. In order to detoxify cyanide in the tails for tailings dam, effective and inexpensive technologies involving a seasonal use of detoxified reagents were developed. For example, a technology with aldehydes use which is applied by a series of operations. Effluents disposed to the environment are detoxified using chlorination followed by almost a complete destruction of toxic cyanides and thiocyanates. Before disposal, chlorinated water is settled to precipitate the resulting hydroxides of metals and complete chemical reactions such as a full decomposition of hypochlorite ions. In order to protect ground water, watertight screens from local water-resistant materials are used. The samples of these materials were previously tested and chosen according to their maximum ability to adsorb toxic compounds in the tailings pond. If local water-resistant materials are not available, whole welded impermeable polymer screens are used. The options mentioned allow the storage of cyanidation tails in accordance with national ecological standards. Keywords: cyaninides, thiocyanates, wastes, environmental safety, recycled water-supply, detoxification, storage

Sep 1, 2012

By James A. Finch, Linda Restrepo, Mitra Mirnezami, Amy Buchanan, Maryam Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally reveals two aggregation maxima at pH 8-10 and 10-12 (Figure 1). From measurements on sphalerite and silica suspensions the double maxima could be replicated. These maxima correspond to the effects of Zn and Mg ions. The aggregation mechanism of both ions is related to the formation of the corresponding hydroxide precipitate. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By Thomas Pretz, Alexandra Pehlken

Sampling of municipal solid waste is known to be difficult to sample if it has to be representative. When dealing with municipal solid waste, the usual method is to study separately waste material below 40 mm and particles bigger than 40 mm. The material < 40 mm cannot be sorted manual and is termed the “fine fraction”. The particles > 40 mm can be separated manually and are usually sorted into pre-defined groups of materials. These groups can be defined depending on the demand of quality assurance. But standardisation of procedures is not far progressed, even for the widely practised sorting methods.

Jan 1, 2003

By Janusz S. Laskowski

It is customary to assume that wettability plays an important role in coal flotation, and it is well established that while hydrophobic metallurgical coals float easily, low-rank less hydrophobic coals are difficult to float. However, coal surface wettability plays a dominant role in many coal preparation unit operations. As it will be discussed in this paper, it affects coal-dewatering, selection of flocculants, fine coal pelletization and briquetting, and even coal handleability.

Sep 1, 2012

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

Pyrite is one of sulfide minerals most widely distributed in the earth. During the flotating separation of metal sulfide and the floating desulfation of coal, it is often requaired to restrain pyrite. However, the result is not very satisfactory because of the little difference of floatability of minerals to be separated. The problem is extremely outstanding for the floating desulfation of coal. Researchers carried out a number of experiments with T. ferrooxidans (Yang et al, 2001; Zhou et al, 2000; Zhou et al, 2001; Wei et al, 2001) for an enhanced restraint to pyrite. The results showed that the T. ferrooxidans after being cultured works the best in restraining pyrite. After 10 min pretreatment, the removal rate of pyrite from coal is up to 80%~90%. The research results by Yuan Xin et al (Yuan et al, 2000) show that T. ferrooxidans can restrain effectively the floatability of pyrite and can reduce the recovery of pyrite from 95% to 8%. Though the restraining properties of T. ferrooxidans to pyrite have been proved by many tests and experiments, there are very limited reports on its restraining mechanism. Thus, a systematic experimental research is carried out in this paper.

Jan 1, 2003

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure for the predictive simulation of flotation circuits far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, circuit survey and laboratory batch flotation data collected from an industrial flotation circuit are analysed. The data demonstrate that streams in an industrial flotation circuit exhibit varying particle floatability – concentrate streams typically float faster than tailing streams (Figure 1(a)). This floatability, however, is generally conserved around the various units within the flotation process (i.e. the effective floatability of the combined feed and product streams of a unit is equivalent (Figure 1(b)))."

Jan 1, 2003

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin.The use of selective ion exchange to recover metals from sulphuric acid liquors has been studied for a long time. Companhia Vale do Rio Doce (CVRD) has been actively involved in hydrometallurgical applications of IX and has researched in selecting the optimum resin for nickel and cobalt selective removal and the design of a suitable IX circuit. When an IX operation is contemplated for a specific application, it is followed a screening process which generally involves consideration of the solution composition and pH, speciation of the metals in the liquor to be treated and other possible techniques that can be applied to achieve the desired specifications or recoveries. Once a decision has been made to use IX for a specific application, relevant testwork should be done to select the most cost-effective resin and design the IX circuit to achieve the desired criteria. The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to-solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment"

Jan 1, 2003

By Slobodan B. Vujic

"For the requirements of the mining company “Rudnik-Rudnik”, engaged in undergr-ound exploitation of polymetallic ore and lead, zinc and copper concentrates production, the Department of Computer Application of the Faculty of Mining and Geology, University of Belgrade, designed a computer supported and integrated information-management system. This paper presents a concept of this system covering both monitoring and management of production in ""Rudnik-Rudnik"".The ""Rudnik"" Rudnik, Yugoslavia is a mining company, engaged in underground exploitation of polymetallic ore and production of ore, zinc and copper concentrate as well as other metals such as silver, bismuth and cadmium. This mining company runs stable business activities and undergoes a permanent growth of valuable production volume.The basic characteristics of production-technical system of ""Rudnik"" company are: uniform and up-todate technical-technological solutions: linking of production chain from underground exploitation of ore to flotation, namely final product - concentrate of lead, zinc and copper; complete mechanization of production; relatively low level of computer technics implementation; namely, ununiformed implementation of different application of computer-supported information technologies in production and business activities of the Company.These are the assumptions on the basis of which the management of the Company made a decision, in 1999, to upgrade information-management functions through development and application of modern integrated and computer-supported production-business information-management system (hereinafter: IMS, namely IMS Rudnik). For this purpose the Company requested the Department of Computer Application, Faculty of Mining and Geology, University of Belgrade to make the Project on IMS for their needs."

Jan 1, 2003

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

Although the cyanidation process for gold leaching has been applied for more than a hundred years, some aspects of it, such as the passivation of the gold and the depassivating action of heavy metals, are still not well understood. In this work the anodic behaviour and surface composition of gold in alkaline aqueous cyanide with lead additions were investigated using polarization experiments and XPS. It was found that lead in the solution activated the gold at low concentrations, somewhat more positive than the reversible potential for gold, but that the activity again decreased at higher concentrations of lead. The potential range for the activation of the gold coincides with that where underpotential deposition of lead occurs, i.e. –200 to –600 mV(SCE), as indicated by the surface composition of the gold, shown in figure 1. Note that the concentration of lead on the surface of the gold only increased with time in the bulk plating potential range for lead, where gold is not activated by the presence of lead. It is also shown that up to 20 mg/L of lead added to the solution will activate the gold, provided that bulk plating of the lead is avoided. It is also important to avoid reducing conditions during leaching, where bulk plating of lead may occur, if the gold is to be activated by lead to achieve a high leaching rate, as the bulk plated lead screens the surface rather than activating it.

Jan 1, 2003

By Heribert F. Broicher, Arne Volland

"The analysis of laser-induced fluorescence (LIF) combines remote sensing techniques with laser spectroscopy. Over variable distances different rock types are identified or changes in the quality of one rock type are recognised. LIF Analysers operate non-destructive, non-contact, on-line and in real-time. Installed over conveyors or over driveways the analysers ""look"" at the moving bulk solids 20 times per second and provide in real-time information for downstream sorting, blending or optimisation of processing. LIF Analysers recognise rock types (hardness information or dilution control), degrees of alteration, degrees of oxidation and –semi-quantitative- content of certain minerals in an ore. Only under favourable conditions quantitative assay information can be obtained, as e.g. the phosphorus content of Kiruna type iron ore.The main application of LIF Analysers is seen in big open pit operations, where the muck is trucked to an in-pit crusher and the crushed rock conveyed out of the pit to its respective destination: e.g. the primary high grade ore to the mill, the low grade or oxidised ore to the leach pads and the internal waste to the dumps.In underground mining and especially in block caving operations dilution control is of utmost importance. Here a LIF Analyser mounted on the back of a pick-up truck can be moved from drawpoint to drawpoint and quickly assess the degree of dilution.Closer to the mill the stockpile management based on LIF analysis will lead to stockpiles sorted according to rock type (hardness), degrees of alteration and oxidation. In case of direct feeding rom ore to the mill the knowledge of the type and quality of all the material between the in-pit crusher and the mill facilitates optimisation of e.g. reagent dosage."

Jan 1, 2003

By Valentin V. Shatalov, Irina V. Pastukhova, Alexander V. Kurkov

"We have developed a technology to improve the quality of low-grade concentrates containing minerals of tantalum, niobium and tin on the basis of given conception by the way of improving selectivity and using certain reagents composition. The basic collector presents a traditional or complex-forming collector used together with organic diphilic reagents – the secondary reagents regarding the basic flotation regiment, capable of forming associates with the main collector on the surface of the mineral, thus altering the interaction energy. In the given process the main collector is the fraction of hydroxamic acids C7-C9, the reagent of the secondary action – sulphosuccinamate, which added in moderate concentrations range provides for a synergistic effect.We have determined the parameters of the process stability and necessary modifying reagents for a selective recovery of tantalum, niobium and tin minerals from refractory products. Variants have been studied where the main collector and the secondary action reagent were substituted with some more efficient flotation reagents. A possibility of a more flexible reagent compounding for the process has been shown. The flotation process is highly stable regards the saline composition of the liquid phase in the pulp. It can operate under conditions of the complete water recycling with the total salt content up to 12 kg/m3, iron up to 1.2 kg/m3.The given results consider the efficiency testing of the suggested technology for the gravitation products, which were obtained from ores of various genesis and contain large quantity of the most refractory minerals, such as topaz (80%), gamet (55%), tourmaline (30%). High selectivity of the process has been registered with the metal recovery about 92-98%, which appears to be similar to hydrometallurgical operations under certain conditions."

Jan 1, 2003

By C. Gomez, J. Finch, R. Dalhke, J. Torrealba-Vargas

"The dispersion of gas into bubbles is an essential feature of flotation machines. Three measurements have typically been used to describe the dispersion: superficial gas velocity (Jg), gas holdup and bubble size along with the derived quantity, bubble surface area flux. Measurement devices continue to be developed. The McGill Jg sensor based on accumulating bubbles by natural buoyancy comprises a tube with a valve and pressure transducer (Figure 1). The tube is immersed at a desired location and depth (H1) in a flotation cell. On closing the valve pressure increases to a maximum (P1) when the tube is full of air. The Jg is estimated from the slope of pressure-time curve (dP/dt).The relationship between Jg and dP/dt is derived from first principles. Testing the relationship is difficult in a flotation machine as the spatial variation in Jg is generally not known. This problem is overcome using a specially designed experimental setup and the estimated Jg is shown to equal the known Jg.The derivation reveals the importance of bulk density (?b). The sensor was modified to provide an estimate of ?b (Figure 2). A second tube was added immersed to a different depth (H2) and kept full of accumulated air giving a pressure P2. The estimate of ?b is given by (P1-P2)/(H1-H2) (i.e., at the end of collecting the pressure-time data). This two-tube sensor also helps dampen process noise as illustrated by a sudden change in level when collecting the pressure-time curve. Both the original and modified versions have been widely used in plant test work."

Jan 1, 2003

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By S. M. Marr

"Water availability and water-related environmental impacts are now one of the most significant challenges facing primary production within the global minerals industry. Whereas the industry has, to a large degree, been able to demonstrate a collective response to greenhouse gas emissions and global energy demand, no such strategy exists for water. In part, this is because water quality and availability are regional issues, but also too because water quality cannot be defined by a single attribute, and extrapolation of any set of water quality indices to their associated environmental impact is no trivial matter. In design situations specifically, the situation is exacerbated by the fact that process engineers typically focus on site water management, and consent authorities are primarily in catchment level issues. As a result, an integrated approach to water management is difficult. This does not stem from an unwillingness by members of the professional team to engage with the total picture of water quality and availability, but principally from the fact that there is no common language through which to approach the problem.It is imperative for process engineers to extend their design system boundary, to reflect the geographic scales over which water impacts need to be quantified. It is not suggested that chemical engineers and metallurgists should become experts in geochemistry, hydrology and limnology. Rather, the challenge is to develop tools through which better communication of the relevant environmental impacts can be achieved.It has been estimated that 50% of the capital for new plants is devoted to handling wastes. The integration of mass exchange processes, adopting a life cycle analysis framework for considering environmental impacts and shifting the emphasis from effluent concentration to environmental impacts should be adopted in the framing of the design problem have been suggested as techniques of Environmentally Conscious Design. Shifting the focus from effluent concentrations and legislative requirements to evaluating the environmental impact is an important step towards improving the overall environmental performance of a process facility."

Jan 1, 2003

By Andrei Kolesnikov

"The results of CFD modelling of complex heat transfer and fluid flow in DC electric arc furnace are presented. The model includes energy and momentum conservation equations for gas phase (freeboard), liquid phase (molten bath) and solid phase (walls and graphite electrode). Simulation revealed the temperature distribution in all elements of the furnace. The influence of the arc and melt resistance on the temperature distribution is discussed.Computational Fluid Dynamics (CFD) becomes a powerful tool for better understanding of the heta and mass transfer processes in industrial equipment. In current work commercial CFD software STAR-CD was used to analyse complex heat transfer in DC EAF, including forced and natural convection, conduction and radiation. The finite volume solver using body-fitted grid was used. The grids are non-staggered hexahedral grids and all variables are evaluated at cell centers. Steady-state calculations were performed with PISO algorithm. For the convective terms in equations the hybrid differencing scheme was used. An upwind differencing scheme was used for other terms. Conjugative heat transfer was taken into account in heat transfer calculations on gas-liquid and gas-solid interfaces. Radiation from the arc and inner surfaces of the furnace was calculated by a “discrete beam” approach. Source term in energy conservation equation was used to represent heat release in the zone occupied by the DC electric arc. The volume of this zone was calculated from semi-empirical equations. The Joule heat and heat due to chemical reaction in the melt were calculated through the source term expression in the energy balance equations for the slag and metal in the molten bath. The gas acceleration in the electric arc zone and stirring of the slag due to gas bubbles motion were accounted for by momentum source terms in the momentum conservation equations.All simulations were carried out using axisymmetric two-dimensional grid. The grid resolution was 20 cm per cell in most part of the furnace, except the arc region, where resolution was 5 mm per cell."

Jan 1, 2003

By M. H. Moys, H. Dong

"Discrete Element Method (DEM) has become a standard tool to simulate grinding mills in order to gain information about load behaviour, power drawn, etc. However, parameters necessary to run a simulation are not always readily available. For example, the coefficient of restitution used in DEM simulation from the literature ranges from 0.1 to 0.9 due to lack of accurate values. The lack of correct input parameters results in the fact that some simulation parameters are adjusted to match the simulation prediction with the experimental results. It is inappropriate to tune one single parameter arbitrarily in order to fit the prediction with experimental results. The correct value of parameters for DEM simulation should be established, and rigorous validation on simulation results by DEM needs to be done.The objectives of the ongoing project are to measure the coefficient of restitution at conditions analogous to grinding practice. Equipment has been built to measure the coefficient of restitution. A typical case of impact test showing the vertical position of a ball as a function of time is presented in Figure 1. The coefficient of restitution between steel ball of different sizes and the targets including steel liner (e = 0.91), mild steel block (e = 0.57) and rubber liner (e = 0.7) have been measured. The coefficient of restitution reduces to 0.38-0.52 when there is a layer of coal particles (1-2 mm) on the steel liner. The effects of ball size, drop height on coefficient of restitution are investigated. Then a DEM code is developed of several contact models to simulate the impact process. This code can reveal details on velocities (translational and rotational) and forces (normal and tangential) during the brief impact interval. Figure 2 is a comparison of the rebound rotational velocity between experiment and prediction by different models. The results can be used as DEM input and to assess contact models."

Jan 1, 2003

By Grigori I. Voiloshnikov

"The long-term studies on development of the technology for precious metals recovery using activated carbons executed by Irkutsk Research Institute of Precious and Rare Metals and Diamonds (IRGIREDMET) were finished by successful introduction of ""Carbon-In-Pulp"" process in Russia (1984).The review of some studies, accompanied by development, testing, introduction and subsequent improvement of considered technology, carried out by IRGIREDMET is submitted in this paper.The basic regularities of gold and silver adsorption onto activated carbons from cyanide, thiourea, chloride and other solutions are investigated using various phisical-and-chemical methods ( X-ray photoelectron spectroscopy, Voltammetry, X-ray microanalysis etc.). Using voltammetry it was found that gold cyanide is adsorbed onto activated carbon without chemical changes and partial reduction of gold is possible only during drying of carbon samples before analysis. Metallic gold and silver may be dissolved in boiling cyanide solution at argon atmosphere when they are in contact with activated carbon surface. Gold adsorption mechanism for activated carbons has great differences from that for the ion exchange resins. So the most probable mechanism for gold adsorption from cyanide solution is adsorption of neutral molecules Me n+[Au(CN)2-]n.X-ray quantitative microanalysis technique was developed to investigate gold adsorption kinetics onto spherical activated carbon. Gold profiles in granules of activated carbon for various adsorption conditions were tested (carbon particle size, mixing efficiency, adsorption time etc.). Mathematical methods were used to determine gold diffusion coefficient within activated carbon granule.The properties of various types domestic and foreign activated carbons were tested and the demands to activated carbons suitable for gold extraction were determined. As a result foreign and Russian activated carbons AG-90, AG-95 were recommended for use at Russian gold plants. Domestic adsorbents are cheaper in comparison with foreign activated carbons. The methods to restore carbon adsorption activity including acid treatment and thermal reactivation were tested and implemented."

Jan 1, 2003

By A. T. Sutaone

"Battery grade Mn ore is not found in India except in Dongri-Buzurg Mine, Dist. Bhandara, Maharashtra. The mine located in central India is operated by a premier company viz. Manganese Ore India Ltd., under Central Government Public Sector Undertaking. The company is not selling the product as battery grade material but instead primarily catering to the needs of the iron and steel industry in the country. However, a part of the ore is being used in-house for the production of electrolytic manganese-dioxide in their EMD plant, which is located near the mine.The production of lumpy ore for steel industries generated through multi-stage crushing and screening has resulted in accumulation of about 50,000 tonnes of low grade fines over the year, which contain low of Mn values. Further, the generation of fines is still on going process due to the production of lumpy ores. These fines are stacked in the form of unconsolidated dumps, which create environmental problems like air and water pollution and siltation in the adjoining fields. Besides they are occupying large space, which is scarce in this mining area. The Indian Bureau of Mines under one of its statutory functions has suggested the company to explore the possibility of recovery of additional values under conservation and environmental aspects. Hence the company has sponsored a bulk sample for beneficiation studies in the Modern Mineral Processing Laboratory and Pilot Plant of Indian Bureau of Mines at Nagpur, India. The main manganese minerals present in these mine rejects have been identified as pyrolusite and psilomelane. The purpose of this study was to explore the possibility of evolving a suitable beneficiation flowsheet to obtain manganese concentrates assaying over 72% MnO2 to be used as raw material for the manufacturing of dry cell batteries."

Jan 1, 2003

By O. A. Punishko, G. G. Mineev, Zabaikalsky Ore-Dressing Plant, M. V. Malova, O. V. Belousova, S. A. Bogidaev

"In order to intensify benefication processes (flotation and magnetic separation) for rebellious tantalitecolumbite ores electrochemical machining of pulp (ECM) is suggested instead of costly mechanic-chemical activation and magnetizing roasting. Any change in the surface mineral-semiconductor potential under the action of electrochemical treatment results in the change in the isoelectrical state of the surface and the adsorption property of the mineral with respect to ionogenic reagents-collectors. In this case conditions are created for regulating the ion composition, reduction-oxidation potential and pH of the liquid phase of the pulp without any extra introduction of expensive and often ecologically harmful chemical substances.Ores containing tantalum and niobium are characterized by complex chemical composition, determining their physical properties (conductivity, dielectric penetration, magnetization value, etc.) and their electric susceptibility.The authors investigations show that the pulp electrochemical treatment leads to the increasing magnetic susceptibility of the paramagnetic minerals. The main chemical elements forming the columbite-tantalite minerals except tantalum and niobium are iron and manganese. They determine the rare-metal minerals paramagnets properties. The electrochemical treatment changes the relation of the oxidized and reduced forms of these elements having. The method of cathode pulp treatment before flotation is successfully tested industrially.In the field of noble metals metallurgy new technological proposals are reduced to the following. As is know, the production of noble metals from unusual raw materials demands the elaboration of principally new technologies new technologies in so far as the methods for gold and silver extraction from ores are as a rule low elective and at the existing level of engineering are economically not expedient.The analysis of the main trends in the field of non-standard raw material treatment shows that the perspective ones are the geo- and biotechnological processes (underground leaching and leaching in heaps - UL and HL and microbiological methods of metal extraction)."

Jan 1, 2003

By Yuriy V. Gulyaev, Galina V. Sedelnikova, Valeriy D. Lunin, Valentin A. Chanturiya, Igor J. Bunin

"In Russia the industrial exploitation of ore deposits is determined as a strategic direction of gold extraction industry development. The majority of gold-containing ores of Russia is referred to category of rebellious ores with 3-5 g/t gold content and is characterized by low factors of gold and silver extraction under cyaniding. The resistance of goldcontaining raw materials under their processing is caused by presence of very fine gold particles less than 0,1-0,01 µm in size, associated with the pyrite and arsenopyrite. Significance of the problem of rational rebellious ores beneficiation and high precious metals extraction is increasing from year to year.Group of scientists from IPKON and IRE, Russian Academy of Sciences, has developed highly effective, powereconomic and ecologically clean method of breaking-up of resistant gold-containing ores and their beneficiation products on the base of using an energy of powerful electromagnetic pulses. For the first time there have been designed laboratory installation for resistant raw materials treatment in dry and wet state (solid/liquid ratio = 5:1) and ground material less than 1-0,5 mm.Mechanisms of powerful electromagnetic pulses action on natural mineral components, including dielectrics (quartz, calcite), semiconductors (sulfides) and metals (gold, silver) have been theoretically accounted. Pulses action parameters and ways of pulses generating have been discussed in different conditions. At tension of electromagnetic field, exceeding the electric strength of processing material, an electric breakdown develops in the mineral matrix of sulfides and dielectrics. Under the series of pulses action the forming of plural breakdown channels occurs, leading to strength loss of material and microcrackes developing. Thus, the action makes it possible for leaching solution to access precious metals particles under cyaniding process. Distinctive changing of pyrite and arsenopyrite surface structures under the influence of powerful electromagnetic pulses is confirmed by studies using optical and scanning electron microscopy."

Jan 1, 2003