Search Documents

By James M. Tantalla, Dwight Metcalf, Roderic A. Ellman Jr.

"The construction of a new low head hydro-electric plant at the Cannelton Lock and Dam required the design and construction of a cofferdam to accommodate a deep excavation extending approximately 150 feet below the Ohio River levels. The new plant, which generates about 390 GWh of electricity annually, is owned by American Municipal Power (AMP). A specialist team was assembled to design and construct the cofferdam, marine dike and CB slurry wall that helped make the project successful and on time for project delivery.Because the new plant diverts water from the locks and dam through a powerhouse to generate power, it would need to be partially in the river to operate properly. To accomplish this, approximately 250,000 square feet of land was reclaimed from the river by construction of a marine dike. The dike, combined with the design and construction of a 150 foot deep cement bentonite (CB) cutoff wall enabled construction of the new plant in the dry. Extensive dewatering analyses were performed using Modflow to evaluate pumping requirements and the number of wells needed to maintain ground water at required levels within the side slopes and final subgrade. A monitoring program consisting of inclinometers, piezometers and movement monitoring points were used to monitor cofferdam stability and performance throughout construction. Detailed two and three dimensional stability analyses that included a parametric study of fluctuating river levels and slurry unit weight were performed to ensure stability and suitable low permeability of the trench during cut-off wall excavation both on land and in the marine dike. The wall was constructed with both a hydromill excavating primary panels and a clamshell following behind to construct secondary panels. Data acquisition systems onboard the excavating equipment allowed for detailed confirmation of the continuity of the wall at each interface between panels. Another challenging aspect was the CB mix design for the trench. The cofferdam required the construction of a 1,300-foot long marine dike downstream of the existing dam up to 100 feet tall founded on existing river sediment to enclose the site and cut-off the seepage into the excavation from the river. Marine dike construction utilized vibro-compaction to pre-densify granular fills placed underwater through which the CB trench extended."

Jan 1, 2016

By Joseph T. Coe, Alireza Kordjazi, Michael Afanasiev

Cross-hole sonic logging (CSL) is a common quality assurance measure for the evaluation of the structural integrity of drilled shafts. The results of CSL can be supplemented by a set of tomographic images generated by cross-hole tomography (CT). Although the same access tubes, sources and receivers are used in both methods, CT has the advantage of providing a higher quality image of the possible anomalies in drilled shafts. Nevertheless, it has been reported in literature that the CSL and CT miss anomalies with sizes of smaller than 10 percent of the cross sectional area of the drilled shaft. This implies poor resolution despite the high-frequency of the stress waves utilized in these methods. This issue with resolution can be at least partially attributable to the fact that CT relies entirely on the inversion of the first time of arrival and ignores the information embedded in the rest of the recorded traces. This study examines the application of full waveform inversion (FWI) to generate a higher resolution image of the possible defects in drilled shafts from the same data used for cross-hole tomography. FWI is a wave-field method that aims to directly match the recorded traces with traces obtained from a numerical model of the domain. This has the benefit of avoiding the selection of the first time of arrival, along with increasing the resolution of the final image due to extracting more information out of the traces. Through a series of numerical simulations, synthetic traces were generated from a drilled shaft with defects of known mechanical properties, dimensions, and location. These traces were then inverted to evaluate the performance of FWI for structural integrity testing of the drilled shafts. INTRODUCTION The presence of construction defects can compromise the structural integrity of drilled shafts and negatively affect their performance (O’Neil 1991; Sarhan et al. 2002; O’Neil et al. 2003; Poulos 2005). Several non- destructive testing (NDT) methods exist that are currently used for the evaluation of the structural integrity of drilled shafts. Cross-hole sonic logging (CSL), cross-hole sonic tomography (CT), and thermal integrity profiling (TIP) are well-established and documented in the industry and practical manuals (Brown et al. 2010). NDT methods prevent the need for coring and excavation and are relatively fast and cost effective. Successful implementation of these techniques has also been reported in the literature (Branagan et al. 2000; Iskander et al. 2001; Mullin 2010; Johnson 2016).

Jan 1, 2019

By Hugo Meggitt, Damian R. Siebert, Wystan Carswell

Excavation-induced ground movements are a critical component in the design and construction of deep excavations in urban settings due to the potential adverse effects on adjacent structures and infrastructure. Ground movements are influenced by soil stratigraphy, soil properties, adjacent structures, and construction means and methods. The use of empirical relationships, computer models, and reliance on experience with similar excavations in similar soil conditions often provides a basis for predicting excavation-induced ground movements. In this paper, data from 21 deep excavations approximately 20 ft to 75 ft deep supported by concrete diaphragm “slurry” walls in the Greater Boston area are compared to published literature, considering how different foundation systems (e.g. shallow foundations, caissons, and piles) of abutting structures have been affected by adjacent excavations. The influence of construction method (conventional vs. top-down) on adjacent foundation movements indicate that top-down construction typically results in smaller foundation movements. INTRODUCTION Estimation of ground movements due to excavation is a challenging endeavor, even with complex three- dimensional finite element modeling and high-order constitutive models that are increasingly available in modern engineering practice. Aside from the expense of the soil exploration and testing used to inform these higher-order models, the challenges of modeling past stress history, adjacent structures, and the groundwater conditions during excavation require not only large investments of time during design but also validation from past experience (to avoid a “garbage in, garbage out” paradigm). While site conditions such as soil stratigraphy, soil properties, groundwater conditions, and as-built conditions of adjacent structures can be obtained, measured, and estimated, the effects that means and methods of construction have on ground movements are difficult to quantify. During early phase design, assessments of predicted ground movement are unable to account for all aspects of project construction, nor is it cost-efficient to fully design an excavation while project parameters such as site size and excavation depth are under consideration by the design team. While construction is in progress, benchmarking support of excavation performance and associated ground movements in the context of successfully completed projects allows for a more nuanced view of system performance and provides the opportunity for more informed decision-making (if required) as construction proceeds. For these reasons, the use of empirical relationships and the collection of historical support of excavation performance holds high value for the practicing geotechnical engineer at all phases of the project.

Jan 1, 2019

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By Brett K. Mainer

In the summer and fall of 2007, Drill Tech Drilling and Shoring, Inc. designed and built three 24-foot inside diameter shafts in Northern California using soil mix panels for support. The soil mixing was performed using the Bauer Cutter Soil Mix (CSM) method, by which rectangular soil mix panels up to 71 feet deep were arranged in an overlapping manner to form a 24-foot inside diameter circle. The shafts were then excavated to depths up to 51 feet. One of the shafts was a test shaft and used only the soil mix panels for support. The other two shafts were located immediately adjacent to the Mokelumne River and were used as access pits for a microtunnel drive under the river. These two shafts had wide flange beams embedded in the panels and were supported with several levels of ring steel placed during excavation. This project was the first use of the Bauer CSM method in the United States. The CSM method has been used extensively in Europe and Asia, but never for this application and never with this high a loading criteria due to water head and microtunnel reaction forces. Soil conditions at the river crossing shafts consisted of sands, gravels, and cobbles over top of sandstone and conglomerate bedrock ranging in strength up to 5,000 psi. Groundwater was within several feet of the surface. The shafts were successfully completed between October 2007 and January 2008, and the microtunnel was successfully completed in February 2008. This paper provides discussion regarding selection of the shoring type, structural design, the soil mixing method, and the mix designs. Shaft construction, shaft performance, and the capabilities of the CSM equipment are presented.

Jan 1, 2008

By Filippo Maria Leoni, Wesley Schmutzler, Matteo Bertoni

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project (Project) in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 92 inch ID forced sewer main relocation and to improve the soils for the base of a new drainage channel. The soils to be improved consisted of sandy fill, soft clays, organics and stiff, plastic clays. A pre-construction soil investigation campaign, followed by a Bench Scale Mixing Programme and a Full Scale Field Test were performed during the pre-construction stage to assess soil properties, select binder type and dosage, and disclose the most suitable combination of injection parameters to improve the different soil layers. Production started at the end of August 2012 and was completed in October 2013; over 3,000 DMM elements were installed to a maximum depth of 57 ft below ground for a total gross volume of approximately 125,000 cubic yard. Each element consisted of two 5.5 ft diameter overlapping columns installed simultaneously, and their layout was such to meet the 100% Area Replacement Ratio required by the design. The ground improvement was successfully completed despite some difficulties due to a considerable amount of obstructions. Wet grab sampling and UCS testing of the retrieved specimens were designed as the main QC/QA method for the verification of the quality of the ground improvement. Upon completion of production, approximately 3,000 specimens were cast. The contract also required continuous coring of at least 12 randomly selected DMM elements and the testing of 8 cored specimens per bore for strength assessment. This paper will illustrate means and methods used in the field to construct the designed ground improvement and the results of the QC/QA program, with a focus on the differences between wet grab and coring sampling methods.INTRODUCTIONThe Rio Puerto Nuevo project involved the stabilization of a major drainage channel using the Deep Mixing Method (DMM), and the relocation of a 92 inch ID forced main sanitary sewer outfall. Previously, in 2004, a 40 x 16 x 2,000 ft. box culvert was installed under a different contract to convey runoff waters to the ocean.However, the connection between this culvert and the upstream network of channels was not constructed due to the presence of the forced main sewer pipe. In order for the drainage system to be completed and function properly, the 92 inch ID forced main needed to be lowered about 20 ft to allow for proper drainage.DMM was chosen by the US Army Corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The DMM was arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for Zone A (deeper and with a higher strength requirement) and Zone B as an example (Figure 1)."

Jan 1, 2015

By Dave P. DeClerck

Hardman Construction was faced with the challenge of completing a large earth retention project on a constricted downtown Detroit site, while maintaining a safe and productive worksite. To do so, new technologies using robotic equipment was instituted. HISTORY The historic J.L. Hudson Building (Hudson’s) in Detroit, Michigan was the premier retailer in the city’s downtown district from the 1890s through the 1960s. The massive flagship store sat at 1206 Woodward Avenue, one of the busiest streets in the Detroit area. Hudson’s broke ground in 1891 and would go through twelve renovations and expansions. The last renovations took place in 1946, which gave the building the title of being the largest department store in the world at the time. It spanned an entire city block and boasted 2.2 million square feet of retail space. By the 1970s, Detroit was in an economic downturn. The Hudson’s department store finally closed its doors in 1983. Besides a few working offices, the building sat vacant. The building was unique in that it had four levels underground, offices, mechanical areas, and equipment storage. Following years of neglect, the Hudson’s building was seized by the state and transferred into the hands of the city. The city had it demolished in 1998, (shown in Fig. 1) to construct a new, four- level underground parking garage as well as a potential future above-grade development (Sewlck, 2017). The building was imploded in one of the largest implosions of that time. The building rubble filled the underground rooms and helped to stabilize the exterior concrete walls and keep them from collapsing.

Jan 1, 2019

By Jean Wehbe, Daniel C. Brahana

"The new Mercedes-Benz Stadium (MBS), home of the Atlanta Falcons, is part of a new era of stadium construction in the U.S. These new-age stadiums are larger and have more amenities than their predecessors. Many of the MBS’s features, including its innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are supported by drilled piers. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 ft (1.8 m and 1.9 m). Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings were used to support the more lightly loaded portions of the structure.The focus of this article is the construction aspects of the drilled pier foundations. Initially, a fairly extensive drilled pier load test program was performed. Load testing included a Statnamic compression test, two Osterberg Cell tests and two lateral tests. Production pier installation included over 3,800 linear ft (1,158.2 m) of earth excavation and over 1,350 linear ft (411.4 m) of hard rock excavation. The piers contain more than 6,600 cu yd (4,587.3 cu m) of concrete and 1,100 tons (998 tonnes) of reinforcing steel. Drilled pier installation took about 4.5 months. ABE Enterprises was the specialty foundation subcontractor and Bauer-Pileco was the equipment provider.Site and Subsurface ConditionsThe project site is in downtown Atlanta and was originally occupied by residential buildings. A portion of the site was later developed as a rail yard, and other areas contained light manufacturing, warehouses and other relatively light structures. For the past 15 to 20 years the site had been used for surface parking.Beneath a surficial layer of manmade fill, soil test borings at the site generally encountered residual soil, partially weathered rock and the parent bedrock. The bedrock at the site is highly variable, both in elevation and in hardness/quality. The depth to rock is reasonably uniform within the western two-thirds of the site at about 20 to 50 ft (6 to 15.2 m), with a few exceptions. In the eastern third of the site, the rock drops off dramatically to the north and east. In one mega column cap, there was almost 80 ft (24.3 m) in elevation difference. In two borings in the cap that were 20 ft (6.1 m) apart, the top of rock varied in elevation by 34 ft (10.3 m)"

Jan 1, 2016

By Helen S. W. Chow, Harry G. Poulos

Most modern buildings involve the construction of a basement, often of several levels, to maximize the floor area ratio. The basement walls are generally designed for excavation retention purposes only, and are infrequently considered as elements which can help to support the structural loads from the superstructure. However, the basement walls can provide substantial stiffness and resistance to structural loads, and may contribute to the overall foundation capacity and stiffness. This paper presents a simplified approach to approximate the overall foundation capacity and stiffness considering the various components of the foundation system, including the foundation piles, the basement floor slab, the basement walls and interaction between each foundation component. The effect of the basement walls in enhancing the foundation stiffness values is examined by reference to the results of finite element analyses which consider a foundation subjected to vertical, horizontal and moment loadings. The approximate approach is found to give results that are adequate for a preliminary assessment of the effects of basement walls on the overall foundation response, without the need for detailed three-dimensional finite element analyses.

Nov 1, 2022

By Jeffrey Goodwin P. E., Melih Demirkan Ph. D. P. E., Kevin Tehansky P. E.

Just an hour drive down MD 301 from National Harbor, construction to replace the Governor Harry W. Nice Memorial/Senator Thomas ‘Mac’ Middleton Bridge (HNB) began in spring of 2020. The Maryland Transportation Authority (MDTA) contracted with Skanska-Corman-McLean (SCM) to deliver a new US 301 bridge spanning 1.9 miles from Maryland to Virginia over the Potomac River aiming to improve capacity, safety, and access of the roadway. The project area presented a geotechnical design challenge due to the installation of new bridge foundations in the problematic soils of the Atlantic Coastal Plain alluvial deposits. With the existing bridge remaining in service during construction, and the site’s logistical constraints placing new pile driving operations near existing abutments and piers, a complex instrumentation and monitoring plan was developed to ensure public safety throughout the project. This paper discusses the geological conditions of the project area, the collaborative approach of various design team members to develop an appropriate monitoring plan utilizing various instrumentation, an understanding of baseline conditional movements of the existing bridge, and impact response of adjacent construction activity to help deliver effective new bridge foundations while protecting the old ones.

Oct 1, 2022

By Lance Rasband, Richard Hanke, John Starcevich

"The 17.4 meter (57 ft) diameter tunnel boring machine (TBM), the world’s largest at the time of her launch in 2012, locally referred to as “Bertha,” is stuck. Incapacitated due to mechanical failure approximately 36 meters (120 ft) beneath downtown Seattle, situated precariously between the deteriorating Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to address all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Limited area above the tunnel alignment and the physical restrictions of existing infrastructure, create significant challenges for the design of an otherwise symmetrical shaft, requiring special attention to design and layout. Consequently, the access/recovery shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude.INTRODUCTIONTunneling on Seattle’s SR99 tunnel project began in July of 2013. After slowly mining through a 4.5 m (14.76 ft) thick fiber-reinforced concrete headwall and the first of three stabilized “safe havens,” Bertha would proceed along the proposed alignment through 122 meters (400 ft) of jet grout improved soil at a rate of slightly over 1.6 m (5.25 ft) per day. Once past the improved area, it was planned that “Bertha” – would be moving at a rate of about 11 m (36 ft) per day. By the end of October 2013, Bertha had mined roughly 131 m, (430 ft) averaging 1.4 m (4.6 ft) per day and had begun mining within native soils. By December 2013, tunneling had reached the 244 m mark and Bertha was averaging 3.6 m (11.8 ft) per day, achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.It was initially reported that an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure around the TBM, and allow visual inspection of the cutter head from within the TBM, and also to investigate for the presence of obstructions at the face of the cutter head. During this inspection, fragments of steel pipe were discovered entangled in the cutter head. The fragments were apparently from an abandoned 254 mm (10 in.) diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, tunneling resumed. It was then discovered that Bertha was only able to generate a slow crawl."

Jan 1, 2016

By Rafael A. Rivera

"Since the dawn of construction, there has been a need for excavations, which sometimes need to occur below the groundwater table. Excavations in themselves are difficult enough, with the myriad of requirements, such as engineered support of excavations, considerations for stability and numerous other concerns. Excavations executed in rural landscapes can be accomplished easily without significant consideration to accessibility, adjacent properties or structures, and construction limits and deformations. However, all of these factors can have an impact on excavation considerations in an urban landscape. When digging below the groundwater table, these conditions, along with concerns associated with groundwater drawdown requirements, discharge limitations, groundwater contamination, property limits, adjacent buildings and subsidence concerns, can lead an experienced dewatering contractor to consider diverse installation methodology and equipment to allow construction to occur below the groundwater table.534 W. 29th St. New York, N.Y.There are many things that must be considered when constructing a new high-rise building within a small property footprint measuring 25 ft (7.6 m) wide by 80 ft (24.4 m) in length. When you take into account that the foundation needs to go several feet below the groundwater table and that there are two existing multistory buildings with shallower foundations on either side of the proposed structure, this task now becomes much more difficult. Consideration of geology, groundwater levels, depths of excavation and shoring for the excavation becomes critical to the success of the project. On a regular basis, dewatering contractors confront similar situations in congested cities where available real estate is limited.To minimize the negative impacts of construction dewatering, it is important to mitigate the potential effects of construction dewatering to the surrounding buildings, sidewalks, underground structures, tunnels, subways and other existing infrastructure. Such an instance occurred at the project located at 534 W. 29 St. in New York City. On this particular project, the required drawdown was greater than the typical 15 ft (4.6 m) of suction lift, so a vacuumed can pump system was utilized. The tubing was connected to a vacuumed perimeter dewatering well-point system, which is a predrainage system that is installed prior to the start of excavation for the underpinning of the adjacent structures and for the overall foundation. Each well-point, which was composed of a PVC pipe that was 1.5 in (38 mm) in diameter by 25 ft (7.6 m) long, was drilled to a depth of about 23 ft (7 m) using a hollow stem auger and was installed around the perimeter at a centerto- center spacing of about 7.67 ft (2.3 m). In lieu of a traditional perimeter collection header, and to allow for greater flexibility for the contractor, the well-points were interconnected to a modified vacuum can pump system utilizing ¾ in (19 mm) drop tubes that were “spaghetti” around the perimeter."

Jan 1, 2017

By Raffaella Granata, Daniele Vanni

"This paper presents the drilling and grouting program performed at two abandoned landfills located into former calcarenite rock quarries in Manfredonia, Italy. Tests performed after the abandonment of the landfills detected leachate infiltration into the groundwater, which required the implementation of a remedial program. In order to seal the rock fissures and create an impervious basin at the base of the two landfills, sub-horizontal boreholes were drilled and grouted into the rock under the waste deposits. At the same time, sub-vertical boreholes were drilled and grouted along the perimeter, to laterally confine the landfills. Finally, the landfills were properly capped with an HDPE membrane, geogrid, geotextile and topsoil. The methodology implemented to create a watertight barrier under the two landfills was innovative and cost-effective. Moreover, the drilling and grouting minimized the environmental impact of the remedial work, since the waste remained in their original location and were not affected by the remedial process.IntroductionThe two landfills, “Pariti-1 RSU” and “Conte di Troia”, are located approximately 6 km (4 miles) southwest of Manfredonia, a small town close to Foggia, Italy (Fig. 1). These landfills are located into two rock quarries, formerly used for the extraction of calcarenite (i.e., a weak calcareous sandstone, in tuff facies), and were abandoned in the early 90s. The two landfills cover a total area of about 45,000 m2 (11.2 acres), and mainly include urban solid waste with a depth of up to 25 m (82 ft). The main characteristics of the two waste landfills are listed in Table 1."

Jan 1, 2016

By Patrick J. Hannigan, William H. Walton, Ryan C. Rusk, Van E. Komurka

"The project consists of a 33-story building with two levels of below-grade parking across the entire building footprint. Timely and cooperative teamwork among the owner/developer, geotechnical engineer, testing agency, structural engineer, construction manager, and pile-driving contractor resulted in an efficient, costeffective, high-capacity driven-pile foundation on a constrained urban site with significantly variable subsurface conditions. Design objectives included utilizing the highest allowable pile loads reasonably installed from a drivability perspective, using readily available equipment. A pre-production test program was performed on 16-inch-diameter (406-mm-diameter) steel pipe piles, driven closed-ended and subsequently filled with concrete. The test program included dynamic monitoring of 10 piles during installation, and of select piles during long-term restrike testing with a drop hammer, with one instrumented static load test. CAPWAP® analyses were performed on both end-of-initial-drive and beginning-of-restrike dynamic test records. The site exhibited significant soil set-up, even after relatively short wait times. Testprogram objectives included characterizing set-up profiles. A design set-up profile was used to develop depth-variable driving criteria for both 500- and 600-kip (2,224- and 2,669-kN) allowable load piles. Test program results permitted more-accurate reduced capacities to be assigned to damaged piles, and to piles which experienced practical refusal. These more-accurate assigned reduced capacities decreased the number of replacement piles required by 50 percent, saving both time and cost.PROJECT DESCRIPTIONThe project, located in Milwaukee, Wisconsin, USA consists of a 33-story mixed-use residential building with two levels of below-grade parking across the entire site footprint. Column service loads range from 1,400 to 4,200 kips (6,228 to 18,683 kN). The project is located immediately adjacent to an existing two-story masonry retail building with a partial basement, supported on shallow spread-footing foundations.Subsurface Conditions – The generalized soil conditions are presented in Fig. 1. Site grades were relatively level, with a ground-surface elevation of approximately +53 feet (16 m), Milwaukee City Datum (“MCD”). Fill material from previous construction was encountered to approximate Elev. +33 feet (10 m). Below the fill, medium dense silty sand, to silt with sand, was encountered to approximate Elev. +23 feet (7 m). Underlying deposits consisted of lean clay, with undrained shear strengths ranging from approximately 1,000 to 3,000 pounds per square foot (psf) (48 to 144 kPa). Silty sand, to silt with sand, exhibiting increasing relative density with depth, was found below the lean clay to approximate Elev. -92 feet (-28 m), where hard lean clay (glacial till) with undrained shear strengths in excess of 5,000 psf (239 kPa) was encountered. Borings did not extend below Elev. -103 feet (-31 m)."

Jan 1, 2017

By Renato P. Cunha

The paper explores a parametric analysis of a four-pile group in contact (hence piled raft) and without contact (hence standard pile group) with the superficial soil layer, under a combined set of loadings (moment M, vertical V and horizontal H forces). The major design parameters of interest, as total and differential settlements, and raft bending moments and shear stresses are assessed under aforementioned distinct conditions. The slenderness ratio of the piles is also varied along the analyses, allowing the establishment of its influence on the derived parameters.

Jan 1, 2006

By Ihab Allam PE, Meeok Kim. PE. Ph. D

The wet weather equalization basin (EB) planned for Pacifica, CA is a 45 feet deep rectangular shaped underground water tank containing over 2.1 million gallons of water, and located only 500 feet away from the Pacific Ocean. The location and size of the water tank, and the geotechnical characteristics of the selected site presented many engineering and construction challenges. The engineering had to consider a structural system which can fit into the limited area of the site and yet need to meet the storage volume requirement. In addition, the system construction should meet the city’s tight budget and schedule.

By Timothy Nelson, Simon Burnworth

"The University of California’s new Berkeley Art Museum and Pacific Film Archive will showcase a collection of art and film in a facility that pairs an existing 1930s-era printing press facility with a new, architecturally unique auditorium wing. The centerpiece of this adaptive-reuse project is the existing 3- story art-deco Administrative Building, which will be integrated into the new museum and provide approximately 18,000 square feet of usable space. Degenkolb Engineers, as the shoring engineer of record, along with Condon Johnson & Associates Inc., the shoring contractor, worked together with general contractor Plant Construction Company to design and build a temporary structure to facilitate the complex retrofit, renovation, and expansion of the Admin Building. This paper will discuss the challenges faced by the design and construction team, the sustainable solutions implemented on the project, and the collaboration between teams to meet the unique constraints of the project and the site.INTRODUCTION AND PROJECT BACKGROUNDThe Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California Berkeley (UCB) campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home."

Jan 1, 2017

By John C. Niedzielski

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site?s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The full-scale field test played a significant role in the design of the project?s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

By A. Flora, E. Bilotta, F. Foria, V. Nappa

"All the typical applications of deep mixing rely on the good mechanical properties of the improved columns to strengthen or stiffen the ground for a number of geotechnical applications.This paper focuses on a completely different kind of deep mixing, carried out in order to obtain columns much softer than the surrounding soil. This kind of deep mixing, named Soft Deep Mixing (SDM), is introduced as an original means to tackle seismic risk, and can be convenient when the existing structure to be protected has a historic relevance that cannot be altered with structural modifications. The idea is that properly assembled layers made of partially overlapped SDM columns, with dynamic impedance much smaller than that of the surrounding soil, will filter and reflect most of the seismic energy.The paper presents the results of some 2D parametric numerical analyses aimed to investigate the seismic performance of this innovative approach. Simplified dynamic inputs (Ricker wavelets, having only one largely predominant frequency) were adopted to better understand the effect of signal frequency. The analyses show that the effectiveness of the soft grouted isolating barrier depends on soil and SDM geometrical, physical and mechanical properties, as well as on the frequency content of the seismic input.INTRODUCTIONPassive structural systems installed at the foundation level of existing buildings are a common solution to protect them against earthquakes. However, installation procedures are expensive and not always feasible, as for instance in the case of valuable buildings. As an alternative, ground improvement techniques can be used to modify ground properties, in order to mitigate the intensity of shaking at ground level. The propagation of shear waves in the ground can be modified by introducing a layer of artificially modified material, having a dynamic impedance (defined as n =p VS, where p is the material density and VS the velocity of shear waves) very different from that of the natural soil. Both very high or very low values of the dynamic impedance of the grouted soil (nt) can be effective in reducing the overall transmitted energy, with the difference that – for a given reduction of the transmitted energy - stiff grouted layers tend to filter the low frequency components of the amplitude spectrum without modifying in a significant way the high frequency components, while soft grouted layers have the opposite effect. Then, ideally the choice of the best grouting technique should be made considering the effects of the different frequency components on the building to be protected. These effects are detrimental for the structure when they are close to its natural frequency: high frequency components result into large structural loads on massive squat structures (high natural frequency), and low frequency components may be critical for tall and flexible structures (low natural frequency). Therefore, the typical procedure of stiffening the uppermost soil layers regardless of the kind of building to be protected is not necessarily beneficial, and for the case of squat structures soft grouting should be preferred. However, this procedure has not been taken into account yet in the engineering practice, and may pose static problems at ground level (i.e. excessive static settlements)."

Jan 1, 2015