Search Documents

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Pratter P., Boley C.

Polymers are well established in geotechnical applications, for example in ground improvement, where the polymers act as a binder that, when cured, holds the grains together by adhesive and cohesive forces. The subject of this research work is an innovative composite of polymers and gravel, which differs from conventional grouting materials due to its adjustable material properties. With these specific properties, the semi-rigid material can be optimally adapted to the local ground conditions and the individual framework conditions of a construction project. For the characterization of the composite material, stateof- the-art methods, such as image processing by segmentation, are presented. Segmentation is suitable for quality assurance and monitoring of laboratory samples and soil samples directly from ground improvement on the construction site. The load-bearing capacity of the innovative material can even be increased to the order of magnitude of concrete. For this reason, the soil mechanical laboratory tests in this research had to be modified and even expanded by rock mechanical laboratory tests. Based on the experimental investigations, the importance of this innovative material for practical application is demonstrated by a calculation example from construction practice, which shows that even difficult ground conditions can be handled with it.

May 1, 2022

By Rob Jameson

"Although seismic retrofit is recognized as a key micropile application, widely-used reference documents do not clearly address design and testing recommendations for micropiles that are loaded primarily under seismic conditions. The principles of micropile design and construction and their application to seismic retrofit projects are well understood and executed by leaders in the field. As the micropiling market grows, a wider audience relies on the information presented by DFI and similar industry groups. State-of-practice updates appear periodically in conference proceedings, but examination of recent bid documents makes it clear that there are opportunities to improve the specification of load, deflection, testing and acceptance criteria on many seismic retrofit projects. Updates to the FHWA Manual or DFI Sample Specification that specifically address seismic retrofit cases would be useful tools to disseminate information and enhance the state of practice.Micropile Survey UnderwayAs one step in this process, I am distributing surveys to contractors and designers prior to DFI Super Pile ’09 (June 4-6, San Francisco) seeking recommendations for design and testing procedures applicable to seismically loaded micropiles. I am also requesting any existing references that could be promoted as a standard for these cases. Anyone interested in participating in this survey, should contact me at rjameson@malcolmdrilling.com. Seismic RetrofittingMicropiles are ideally suited to seismic retrofit applications. Their high-tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. They can be installed within and around the access limitations of existing structures, and can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones.Seismic retrofits have included micropiles since the early 1990s, and they are now widely specified in the Western U.S. In the San Francisco Bay Area alone, thousands of micropiles have been installed for seismic upgrades of highway and transit aerial structures, and retrofits of commercial, residential and public buildings. Micropile use is growing in both public and private sectors, with large-scale retrofit projects currently underway for both the Bay Area Rapid Transit (BART) system-wide upgrades and renovations at San Francisco Airport."

Jan 1, 2009

By Sarah Ramp, Daniel V. Cacciola, Justin Labrozzi, Shafiq I. Siddiqui, Faisal Ahmed

"Construction of embankments up to 34 ft in height for twelve ramps and roadways needed for the New Jersey Turnpike Interchange 14A project required ground improvement. The subsurface conditions, consisting of up to 30-ft thick layer of highly-compressible peat and organic soils, would induce up to 8 ft of primary and 4 in. of secondary consolidation settlements to the embankments over a long period of time. Innovative ground improvement solutions were needed to meet unique challenges posed by the poor subsurface conditions, space and existing utility constraints, aggressive construction schedule, and massive size of the project. A variety of ground improvement techniques were utilized in six different zones of the embankments to limit settlements and ensure stability of the embankments. These techniques included preloading with surcharge and prefabricated vertical drains (PVD), load balancing using light weight fill, and concrete column rigid inclusions (RI). Additionally, augercast piles with load transfer platform were used under an existing bridge with low vertical clearance. An innovative approach consisting of preloading with surcharge and PVDs followed by installation of RI was needed in one of the six embankment zones with the worst, i.e., very soft, soil conditions. The design of the RI was performed by a specialty ground improvement contractor (SGIC) using Plaxis 2D and 3D softwares. The performance of the ground improvement systems was verified and monitored by load tests and instrumentations. This paper presents details of the ground improvement design, construction, monitoring results, and lessons learned, with a focus on the RI.INTRODUCTIONNew Jersey Turnpike Interchange 14A is located within the cities of Bayonne and Jersey City, in Hudson County, New Jersey. The New Jersey Turnpike Authority (NJTA) identified Interchange 14A as an area of mass congestion in need of redevelopment to improve the increasing demand of traffic and roadway safety. The New Jersey Turnpike Interchange 14A project included the construction of twelve (12) new roadways, in addition to the construction of four new bridges. The limits of construction are shown in Fig. 1.The fill height required to construct the roadway embankments varied from 2 to 34 ft. The proposed embankment side slopes varied from 6H: 1V to 2H: 1V. Additionally, mechanically-stabilized-earth (MSE) walls were utilized to retain the embankment fill along some segments of the roadways. As shown in Table 1, the proposed roadways were divided into six zones, based on location, subsurface condition, and embankment height."

Jan 1, 2017

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan PhD

The experience gained during more than 900 Crosshole Sonic Logging (CSL) tests on drilled shafts shows the importance of establishing proper project acceptance and repair protocols. Drilled shaft evaluation is a multidisciplinary task that should not be left solely to the outcome of the CSL test. This test allows to characterize and delimit areas of different qualities of concrete, and it is important that all the interested parties understand the difference between flaws and defects. The information presented here is intended to give a guideline to contractors, inspectors, engineers, owners and clients on how to deal with acceptance and remediation of defective drilled shafts, detected using CSL tests. A database of flaws is presented depending on their location, intensity and remediation method. Procedures that allow the flaws to be analyzed are presented in order to dismiss or classify them as defects. In many cases, the CSL test may indicate an anomaly, but by coring the concrete and analyzing the structural demands and conditions, the flaw can be classified as non-severe. When flaws are classified as defects, their repair will depend on the area where they are located in the drilled shaft pile. In this document two procedures are described for repairing defects depending on their location. For defects in the drilled shaft head area, the procedure takes into account the interaction between the new and old concrete. For repairing the middle zone of the drilled shaft by grouting, the major concerns are the difficulty of accessing through the drilled shaft at deep depths and the communication between boreholes. For defects at the drilled shaft tip, two proposed remediation methods are presented. Finally, tomography tests are presented to compare the effectiveness of remediation by grouting.

Oct 1, 2022

By Andrea Gambi, Giancarlo Olivucci, Maurizio Lenzi

"In the paper a criterion for the evaluation of the sharing of the lateral loads in a piled foundation is presented. It relies on the the compatibility condition between the rotation of the rigid pile cap and the rotations of the pile heads, following in that the criterion suggested by the Eurocode 8 - Part 5. This assumption leads to an analytical solutions which allows to deal with the sharing of the lateral loads and moments by means of two main interaction parameters only. A sharing domain is also derived and it shows the role played by the eccentricity of the lateral load on the values of the axial forces and of the bending moments at the head of the piles.INTRODUCTIONIt is well known that the interaction among soil, piles and foundation is one of the most complex subject to deal with in Geotechnical Engineering. Its rigorous study needs to employ suitable finite element software nowadays available and able to take into account the non linear behavior of the soil as a continuum and the inelastic response of the structure. A deep insight to the topic of the sharing of the loads cannot obviously renounce to this approach.On the other hand it is a daily need of the designers to have at their disposal simple tools that allow to make preliminary evaluations of the basic equilibrium conditions. To this purpose many methods of analysis have been developed in the past to face the sharing of the loads in a simplified version. The present contribution follows this way trying however to introduce some improvements that leads to find a solution that satisfies both the equilibrium of the forces and the compatibility of the movements (Lenzi, Gambi, Olivucci, 2002). The proposed model allows to identify the basic parameters which govern the sharing of the lateral load and it allows to perform also parametric analysis and quick checks that may be useful in the design of the piles."

Jan 1, 2005

By Riad Diab

In 2018 the Caisse de Dépôt et Placement du Québec (CDPQ) awarded a $6.3 billion (U.S. dollars) design-build contract to the Joint Venture (JV) team NouvLR for the design and construction of one of the largest automated transportation systems in the world, called the Réseau express métropolitain (REM). The REM project is a 67 km (41.6 mi) light rail system with 26 stations linking downtown, the airport and the greater Montreal area in Canada. Out of the 67 km (41.6 mi) network, over 25 km (15.5 mi) is being constructed on a 650- span elevated structure founded on single drilled shafts socketed into rock. Optimizing the design of the drilled shafts was one of the main objectives of the geotechnical team, as it would likely result in shorter shafts that help significantly reduce the project costs. As part of the optimization process, three static axial load tests and two fully instrumented lateral load tests were performed, during the preliminary design phase, on sacrificial shafts to simulate the ultimate load level and validate construction procedures.

May 1, 2022

By Kenneth R. Chadwick, Thomas J. Tuozzolo, Terence P. Holman

"Micropiles are often installed to retrofit existing foundations that experience distortion and to underpin structures prior to future construction. The Dublin Road Pump Station project is an example of retrofitting due to a basal failure during construction that compromised the bearing capacity of the soils. A completed pump station settled and had to be restored to its original position, and work could not proceed until a new support system for the partially completed wet well could be designed and installed. The project involved the construction of three below-grade structures for a new pump station in a growing area of Jackson Township, N.J. The general contractor constructed three pump station structures consisting of a pump chamber, wet well and an inlet chamber in early 2006.The geologic conditions beneath the project site (Figure 1) consisted of loose/soft to medium dense/stiff sand, silt and clay to a depth of 40 ft below ground surface, underlain by medium dense to dense glauconitic silty fi ne sand. When the general contractor was constructing the wet well, which involved an internally supported sheet pile excavation 32 ft below the ground surface and 28 ft below the static groundwater level, basal failure, boils and ground loss occurred. Driven piles were installed to support the wet well structure, but additional ground loss was observed within and outside the sheet pile excavation, followed by settlement of the adjacent pump chamber structure. Post-failure investigations were conducted by Mueser Rutledge Consulting Engineers, N.Y. (MRCE), a geotechnical and foundation engineering consultant. Their investigation concluded that the ground losses around the pump station structures had compromised the supportive capabilities of the natural subsoils.The owner engaged Moretrench, a geotechnical specialty contractor, to work with MRCE to develop a constructible solution to support the pump station structures in general and to restore the pump chamber to its original position. Knowing that ground loss had already occurred as a function of the initial basal heave and subsequent pile driving, the team selected micropiles as the preferred foundation element, primarily due to their flexibility in bypassing these disturbed zones and generating capacity as a function of grouting volume and pressure. Drilled piles were also recommended due to concerns about causing additional settlement of the pump chamber if driven piles were used."

Jan 1, 2008

By Stephen Buttling, Zhong Rui

"A single unit gas fired power station was being built on the edge of the Gulf of Thailand in 2001. The soil conditions consisted of very soft to soft Holocene Marine Clay, and the site was part of a coast line which had been subsiding below high water mark for some time. In order to provide access around the power station a road system in a figure-of-eight formation was required, and this also needed to be above the design flood level, allowing for future settlement. A ground improvement scheme was proposed and constructed, which consisted of two spacings of prefabricated vertical drains (PVD) over two depth ranges, vacuum consolidation and pre-loading, and rigid inclusions.During the construction phase, the vacuum consolidation was applied for 202 to 221 days in different zones, and monitoring allowed a prediction that the future settlement, including secondary consolidation over a period of 25 years, would be within the range of 175 to 355 mm, which met the contract requirement of less than 400 mm.The power plant was completed and became operational in 2003. Monitoring of the road levels continued, as did the settlement, and in early 2010 the total settlement since the end of vacuum consolidation had reached about 800 mm. The monitoring data both during the ground treatment and for the following 7 years is presented and analysed. This is supported by numerical analysis using 3D finite element methods which shows good agreement with the measured data, and allows a preliminary explanation as to why the predictions were so far out.BACKGROUNDAfter a period of bidding and negotiation, the Eastern Power and Electric Co Ltd (EPEC), an Independent Power Producer, entered into an agreement with the Electricity Generating Authority of Thailand (EGAT) in November 1997 to sell them power. In 1999 an Engineering, Procurement and Construction (EPC) contract and an Operation and Maintenance contract were signed with a supplier to provide a gas-fired (with oil as a back-up fuel) 350 MW combined cycle power plant in Bang Bo, Samut Prakarn Province, east of Bangkok. The site of the plant at Bang Bo is located immediately to the east of the Samut Prakarn Wastewater Treatment Plant, adjacent to the Gulf of Thailand (see Figure 1) in an area of very soft to soft marine clay (Bangkok clay) having low shear strength and potential for excessive settlement. The site layout comprises the main Power Plant components of generating block, cooling towers, fuel unloading area and storage tanks, switchyard and administration block, separated by access roads."

Jan 1, 1900

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By Joseph A. Mann

"Soil mixing is a proven solution for the construction of ground improvement adjacent to sensitive structures due to the use of computer controlled and monitored equipment. The precision to which geometry is controlled can often be the deciding factor for selection of soil mixing versus other means of ground improvement. Protection of existing structures and utilities requires careful planning, investigation, and may demand supplemental control measures. During planning, it is imperative that the process be fully developed by the project team to ensure proper control measures are budgeted; otherwise, the success and safety of a project can be jeopardized.This paper discusses case histories of soil mixing performed in close proximity to large, sensitive, and critical utilities, including foundation support for an existing earthen dam impounding a water reservoir in upstate NY, a buffer zone for a tunnel drop shaft at an operating wastewater treatment plant in Washington DC, and a containment system to protect a major water line along an interstate widening project in Baltimore, MD. The function of soil mixing as ground improvement varied; however, the selection and application of the technique versus other means of ground improvement was specific due to the controlled manner of construction with soil mixing. Through the three case studies, small diameter (3- ft [0.9 m]), large diameter (8-ft [2.4 m]), and mass mixing applications will be discussed. Furthermore, the case studies offer insight into how the geotechnical community in the Mid-Atlantic utilizes soil mixing technology for widely varying applications. Additional topics of discussion will be the design and construction of the ground improvement systems, procedures and execution of the work to protect existing structures, and the QA/QC methods, procedures, and results from the projects.INTRODUCTIONWet soil mixing, also known as the Deep Mixing Method, is a ground improvement technique that improves the characteristics of weak soils by mechanically mixing them with cementitious binder slurry. To construct columns, a powerful drill advances a mixing tool with radial mixing paddles located near the bottom of the drill string. The binder slurry is pumped through the drill string to the tool as it advances and additional soil mixing is achieved as the tool is withdrawn.Wet soil mixing is applicable in a wide range of soils. Soil mixing has been performed at depths more than 100 lf (30 m). Soils vary widely in their ability to be mixed, depending on the soil type, strength, water content, plasticity, stratigraphy, and texture. Almost any soil type, including organics, can be treated with certain soil mixing technologies, although they may require high binder contents and/or pretreatment to achieve the required results. In cases when the target soil is very soft, including some very weak clays and peats, 100% of the soil may require treatment. This complete coverage of soil mixing is referred to as mass mixing."

Jan 1, 2015

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule. SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule.SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By Amy B. Cerato, Shawn Allred, Tatiana Vargas

"Helical piles are deep foundation elements that resemble, and are installed like, a large steel soil screw — they have a slender steel shaft with one or more round helix bearing plates welded to the shaft to provide support to the structure they hold. Helical piles are rotated into the ground with a large torque motor and provide support through soil bearing on the helix bearing plates and along the shaft. The piles are available in many lengths and, due to their small footprint along with their ability to create minimal disturbance to surrounding structures, they are often used in urban settings for foundation repair, retrofitting existing buildings and for new construction projects. Helical piles are routinely installed as foundation elements in seismically active areas, such as New Zealand, Japan and the U.S.Anecdotal observations (e.g., from New Zealand, Japan and the U.S.) have shown that piles with a comparatively small cross-section and high anchoring capacity, such as helical piles, are beneficial for seismic resistance. This is presumably due to the pile’s slenderness, higher damping ratios, ductility and resistance to tipping uplift. In New Zealand, it was observed that helical pile foundations fared much better than driven and drilled concrete piles after the 2011 Christchurch earthquake. In a personal communication, Woods (2016) described that, out of the 300 structures in center city Christchurch that were supported by helical piles, fewer than 10 structures suffered significant structural damage. However, many structures supported by driven and drilled concrete piles were damaged to such an extent that they were condemned and subsequently demolished."

Jan 1, 2017

By Arjan Jovani, Arjan Beqiraj, Përparim Alikaj, Altin Karriqi

"Koman dam is one of most important high dams in Drin River Cascade. Safety of these dam is very important not only in power production but also in social and environmental aspects connected with vital activity of local people living in downstream of Drini River and in economic development of the country. In December 2014, during the rehabilitation works on some protection measures at the downstream dam toe, a considerable amount of water leakage emerged from the dam toe. This was noticed even before, but its amount and physical-chemical properties were not evaluated. In order to study the origin and flow direction of this water leakage, KESH sh.a. (Albanian Power Corporation) realized Geophysical and Hydro chemical surveys, turbidity and flow measurements and respective analyses of them. Geophysical survey consist in Apparent Resistivity surveys and Self Potential survey. The survey was done in 3 lines using Resistivity “Real Section” technique. Results are plotted in Sections and plan maps of resistivity and SP parameter. There are defined possible leakage areas and the main flow directions are defined. Also, there is done a hydro chemical analyse. Nine water samples were taken from the different places as Komani lake, service galleries of dam, dam toe and two karst springs which were analysed for both physical-chemical parameters and isotopic composition of O-18 and D. The attained analytical data found that water from the dam toe leakages shows the same chemical signature and isotopic composition of O-18 and D as the water from the lake, thus confirming the hydraulic connection between them.Also, There is done the analyse of water leakage turbidity and amount of this leakage"

Jan 1, 2016

By Aly Mohammad, Dongyi Yue

"The design of rock sockets for drilled shafts and piles proves to be a challenge for the Design Engineer. The magnitude of loads on the shaft and the behavior of the rock are critical in determining the required socket length. Several acceptable methods are available in the literature to analyze a rock socket under a combination of axial loads, lateral loads and moments. This paper will present a state-of-the-art methodology to analyze rock sockets utilizing deformation characteristics of the rock. This design methodology was implemented in the design of a major project in New York City.The project discussed herein is a marine transfer station planned for construction at East 91st Street along the East River in Manhattan. In order to support the piers and platform structures at a site with relatively shallow depth of the bedrock, rock sockets were required for the drilled shaft foundations. Rock sockets were utilized to provide the required fixity to the foundations and the structures. Acting at the top of the rock sockets are large shear forces and moments created by the lateral loads transferred from the structure.Upon review of the available techniques, a simplified method was proposed and used to analyze the rock sockets with a significant magnitude of lateral loading. The method recognizes two mechanisms through which the lateral shear and moment are transferred to the rock; a) load transfer through horizontal resistance of rock and b) the vertical shear resistance of the bond between socket and rock.The first load transfer mechanism was analyzed using the p-y curve method based on a rock model developed by Reese. The second was analyzed using a bond stiffness derived from the formula and curves utilized in the AASHTO Specifications for calculation of rock socket displacement. By comparing the two mechanisms, the main contribution to the large horizontal shear force that developed in the rock socket is identified.The paper will present a summary of the design methodology utilized in determining the length of the rock socket. It is believed that the presented method will provide substantial cost saving in selecting the most economical and efficient design length."

Jan 1, 2005

By Abdelmalek Bouazza, Aamir Mahawish, Will P. Gates

Bio-grouting by means of microbial induced calcite (calcium carbonate) precipitation (MICP) to improve mechanical properties of granular soils has gained much attention in recent years. The biogrouting process offers an alternative and environmentally friendly approach to conventional soil improvement techniques, such as cement. Bio-grouting by urea hydrolysis has been extensively applied to tackle various geotechnical problems. However, it has yet to be applied to improve engineering properties (compressive strength) of a coarse cohesionless material with the aim using it as sand/stone columns within soft and very soft soils. This paper investigates the effect of using light, moderate and heavy biochemical treatments on the unconfined compressive strength (UCS) of coarse sand columns. In addition, the microstructure of the bio-cemented coarse material has been analysed by X-ray computed tomography (XRCT). The experimental results revealed that the UCS could reach up to 200kPa, 1000kPa and 5500kPa for light, moderate and heavy bio-cemented coarse sand columns, respectively. The microstructure investigations showed that the deposited calcium carbonate can be identified using XRCT imaging and can be associated with the gain in UCS values. Various microstructure properties, such as void ratio, dry density and porosity were also identified and compared with the laboratory data.

Jan 1, 1900

By Seiji Mizutani, Hirofumi Taguchi, Makoto Yoshida, Hidenori Takahashi, Naotoshi Shinkawa, Kazuo Konishi, Yoshiyuki Morikawa, Masaya Kawata

"The lattice-shaped cement treatment method has been used to improve the seismic performance of liquefied sandy soil in Japan. The efficacy of the method has been confirmed by the huge earthquake in Japan. In the present study, a new method to improve sandy ground by using the lattice-shaped cement treatment method is proposed as a liquefaction countermeasure. It is the floating-type and lattice-shaped cement treatment method, where cement treated soil is not fixed to an un-liquefiable stratum. In this method, a fixed-type structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were firstly conducted to confirm the mechanism of the new method. Secondly, a series of centrifuge model tests were performed to demonstrate the effect in a proto-type scale's stress condition. The analyses and model tests confirmed the effect of liquefaction countermeasure of the new method.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2015

By Alexander Filotti, Richard Kalson

"In the last decade, the construction industry has witnessed significant changes in the project delivery systems and contractual relationships between the general contractors (GC) and Deep Foundation Specialty Contractors. The Deep Foundation industry, especially including industry specialty subcontractors, have experienced a significant increase in requests that project risks be transferred through contract documents to subcontractors and suppliers with a decrease in margins for the industry. GCs regularly revise their form subcontracts to take into account recent experiences/contractual trends and newly issued judicial precedent, an exercise that is less frequently undertaken by subcontractors and suppliers. These contradictory trends are at the base of the ethical analysis of subcontracts that comprises the subject matter of this paper. Using contracts as a risk management tool in order to mitigate the general contractor’s risks in the context of dynamic changes in the legislative environment will also be addressed. Furthermore, another possibility for risk mitigation for the industry is to actively promote the introduction of the latest technical developments into the contract documents.CONTRACTS’ ETHICSFor thousands of years, ethics have been a constant presence in our lives and have been debated by different branches of philosophy. In modern times, ethics in business started to be an imperative for the success of a globalized economy.“Ethics are standards by which one should act based on values. Values are code beliefs such as duty, honor, and integrity that motivate attitudes and actions.” (Rumbaugh 2004). Some of these values and actions have been carved in legislation in general and in business legislation in particular. More and more, unethical business practices (e.g., corruption) are identified as the root cause of poverty, underdevelopment, and war around the world. In the context of contract ethics, three aspects are of interest:•,Ethics of contract construction•,Ethics of contracting processes•,Ethics of risk allocation in contracts"

Jan 1, 2016

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"Japan’s Great Tohoku Earthquake and the immediately following tsunami of March 11, 2011 killed more than fifteen thousand people and destroyed numerous buildings and infrastructures in the northeastern part of the country.In addition to reconstruction projects in the areas where the earthquake and tsunami hit, other seismically vulnerable regions in the country have started building new and more robust facilities as well as upgrading existing coastal structures so they will be able to cope with such deadly seismic and hydraulic force. This paper will highlight two different types of aseismic and anti-tsunami levee upgrades currently under construction on the coast of Kochi Prefecture, approximately 500 miles west of Tokyo. The first type is the installation of double sheet pile walls in existing seawalls. The second type is to drive tubular piles into existing levee structures for reinforcing them. Both sheet and tubular piles are being driven by the Press-in Piling Method without removing or compromising the function of the existing structures. 1. BACKGROUNDGreat Tohoku Earthquake of March 11, 2011 caused severe damage to many structures. ASCE’s survey of damaged coastal structures conducted immediately after the disaster by Ewing, et al. (2014) categorizes failure modes of the structures in the following manner.?Overtopping without structural failure.?Overtopping with structural damage or failure.?Wave uplift forces.?Movement of structure off foundation from sliding, rotation, or overtopping.?Impact loads.?Hydrostatic pressure.?Supercritical flows.?Scour.?Erosion.?Abutments end effects.?Subsidence."

Jan 1, 2017