Search Documents

By Aniruddha Sengupta, Rana Chattaraj, G. R. Reddy, Raj Banerjee

"Earthquake induced liquefaction in saturated granular soils is an important phenomenon which causes severe damage to life and property. In the present study, dynamically induced liquefaction of saturated Kasai River sand is studied in 1-g shake table to assess its liquefaction potential. In the shake table, the soil was subjected to sinusoidal motions of amplitude 0.35g at a frequency of 2Hz. A numerical model using FLAC 2D (Itasca 2005) was performed to simulate the shaking table tests. Reasonably good agreement between the experimental and the numerical results has been observed. Moreover, wavelet analysis has been conducted to identify the occurrence of liquefaction in sand and to correlate the observations found from the experiments. The nonlinear curves used to represent shear strain dependency of stiffness of the Kasai River sand was obtained from cyclic tri axial tests.INTRODUCTIONThe term Liquefaction is used in conjunction with a variety of phenomena that involve soil deformations due to cyclic disturbance in saturated soil under undrained conditions. The generation of excess pore water pressure is the hallmark of all liquefaction related phenomena and the reduction in the volume or the tendency of cohesionless soil to densify during undrained loading condition as prevails during an earthquake is also well known. Use of shaking table tests to understand liquefaction of soils has been demonstrated by several researchers (Ye et al. 2013; Ha et al. 2011). Mohajeri and Towhata 2003 and Towhata et al. 2006 carried out 1-g shaking table tests on soil models prepared in laminar box to study the rate dependent behavior of liquefied soils. Ueng et al. 2010 used a biaxial laminar shear box mounted on shaking table to study the settlements in saturated clean deposits of sand and related the volumetric strain in liquefied sand to the relative density for various shaking durations and earthquake magnitudes. Maheshwari et al. 2012 reported increase in liquefaction resistance of reinforced sand through shaking table tests and concluded that the type and amount of reinforcement in the soil layer has influence on its liquefaction potential.The objective of the present study is to compare the behavior of dry and saturated Kasai River sand when subjected to seismic shaking. The Kasai River separates two growing cities, Medinipur and Kharagpur in the state of West Bengal in India. A number of road and railway bridges exist over the river connecting the two cities. The area being in Seismic Zone III, that is, a zone with moderate probability of earthquake, it is important to characterize the behavior of the Kasai River sand during a possible earthquake event especially when a number of bridges are existing over it. Small scale laboratory model tests and numerical analyses using a commercial finite difference algorithm called FLAC2D (Itasca 2005) have been utilized to study the difference in behavior of dry and liquefied Kasai River sand during dynamic loading conditions."

Jan 1, 2015

This specification, along with the drawings, encompasses all designs, materials, products, accessories, tools, equipment, services, transportation, labor and supervision, installation techniques, and testing procedures required for the installation of soil nail excavation support or earth retention systems. This is a Guide Specification designed to assist in the development of project specifications for soil nail excavation support and earth retention systems. This Model Specification is based on generally accepted industry standards but may require modification by the specification writer to accommodate unusual and/or unforeseen site and subsurface conditions and the particular circumstances of the project. Care must be taken to avoid internal inconsistencies. It contains language allowing for a Contractor-Designed Soil Nail Wall, which would be removed if the design is provided by the Owner (e.g. See Sections 1.2 and 4.1).

Jan 1, 2010

By Lassaad Hazzar

The ultimate lateral resistance of piles in cohesive soil is studied using the well-known finite difference code, FLAC2D. The Modified Cam Clay (MCC) constitutive relation is adopted in the analyses to model the cohesive soil behavior, whereas the structural pile model with three degree of freedoms, available in FLAC2D library, is adopted to model the piles. The reliability of Broms's method, still used in the current design practice of piles under lateral loads, is verified. Comparisons between the ultimate lateral resistances of piles and those deduced from the graphs proposed by Broms (1964) are presented in graphs. Different factors thought to affect the lateral resistance of piles in cohesive soil, not adequately considered in Broms's method, such as clay stiffness, pile length, pile diameter and axial load are parametrically studied. A special concern is devoted to elucidate the effects of over-consolidation ratio (OCR) on the ultimate lateral resistance of piles in cohesive soil.

Aug 1, 2013

By Andrew Middleton, Mick Stadter, Chris Crowe, David Chong

"The Level Crossing Removal Project – Package 1 is part of the Victorian Governments commitment to remove 50 of the most dangerous and congested level crossings across Melbourne. This involved removing three crossings on the Frankston Line in the south east suburbs of Melbourne. The works involved replacing approximately 2.5km of at grade track with three rail cuttings up to 8 m deep at each of the bridges that replace the level crossings. The cuttings are retained by piled retaining walls and during the main construction occupation approximately 250,000 cubic metres of soil was removed. The project has presented significant geotechnical challenges due to the location in residential suburbs and tight rail corridor and rail occupation timeframe. These challenges included temporary and permanent wall stability, foundations, earthworks and dewatering. As a result, careful design and innovative construction techniques have been necessary to limit impacts on the community and meet the project timeline.INTRODUCTIONThe Level Crossing Removal Project – Package 1 is part of the Victorian Governments commitment to remove 50 of the most dangerous and congested level crossings across Melbourne. This involved removing three crossings on the Frankston Line where it crosses North Road in Ormond, McKinnon Road in McKinnon and Centre Road in Bentleigh.The project involved replacing approximately 2.5km of at grade track with three rail cuttings up to 8 m deep at each of the bridges that replace the level crossings. The cuttings will accommodate three lines of rail tracks with the cuttings up to 25 m wide. The cuttings are retained by piled retaining walls and during the main construction occupation approximately 250,000 cubic metres of soil has been removed.The project presented significant challenges due to the location in residential suburbs and tight rail corridor and rail occupation timeframe. As a result, careful design and innovative construction techniques have been necessary to limit impacts on the community. The geotechnical challenges generally fell into one of three areas, earthworks, structures and groundwater. The primary earthworks challenge for the project was moving the 250,000 cubic metres of soil in a 10 day window, however, from a geotechnical viewpoint, obtaining a stable subgrade on which to operate the necessary construction plant in a short time frame with constrained site access and time to import materials was the key. Whilst closely watching the performance of the dewatering system, a range of contingency plans were developed to cope with any difficulties."

Jan 1, 1900

It is my great pleasure as mayor of the city of Amsterdam to welcome you today to Amsterdam, and to the 10th International Conference on Piling and Deep Foundations. The history of Amsterdam has been connected intimately with your professions of geo-engineering and geotechnology, since its very first days. It is good to be aware that you are part of a very old tradition. The knowledge that we need today to build and renew the city has been gathered over a century long process so that we fortunately can stand on the shoulders of the giants before us. During the centuries people living in this part of the Netherlands have always struggled against the water. The same waters that brought the opportunity for a seafaring country to discover the world and to build an empire in the 17th century were a threat to the low lying Netherlands.

Jan 1, 2006

By Giulia M. B., Ferruccio Cribari, Alessandro Bertero, Eliano Romani, Roberto Sorge, Francesca Casini

"The use of Artificial Ground Freezing (AGF) to form earth support and seepage control barrier systems has had applications worldwide. These cover a variety of construction problems, including the formation of frozen earth walls to support deep excavations, structural underpinning for foundation improvement, and temporary control of ground water in construction processes. An application of AGF during construction of Line C of Rome underground is described in detail.The new line “C” of San Giovanni metro station was constructed adjacent to the existing line “A” of San Giovanni station; the new metro line “C” is deeper than line “A” and runs below the existing station. The underpass project envisages an Artificial Ground Freezing in order to create a structural and waterproof temporary cut-off suitable to the two new tunnels excavation, while keeping trains running in the safest possible condition. The excavation of tunnels under the water table, with a hydraulic head of over 10 m in not homogeneous soils having different mechanical properties and permeability and below existing sensitive structures, involves special ground freezing sequences and methods, as well as peculiar drilling systems and operations, such as TDDT (Trevi Directional Drilling Technology).Artifical Ground Freezing IntroductionNatural freezing occurs seasonally in many areas of the globe and can affect negatively the engineering performance of geotechnical structures; on the other hand, man-made freezing is a controllable process that can be used by civil engineers to stabilise temporarily the ground in order to support and/or exclude groundwater from an excavation until the final retaining and lining structures are constructed. Freezing and thawing of the pore fluid within soils involve complex thermal, hydraulic and mechanical processes that have significant mutual interactions. For example, phase changes of the pore fluid caused by temperature variations can modify the pore water pressure in the soil, which, in turn, can induce mechanical deformation. At the same time, any changes in the hydraulic and mechanical conditions affect the thermal processes by advection and changes of ice and water contents.An application of AGF which will be presented in the paper, refers to the construction works of Line C of Rome underground. In this case AGF was carried out to provide temporary support during excavation of the two Line C running tunnels directly underneath the existing S. Giovanni station of Line A, in the safest possible condition. In order to keep the trains of Line A operational during excavation, a temporary structure was installed and a real-time monitoring system was conceived in order to control the temperatures of the soil during freezing and the response of the structures of the existing station."

Jan 1, 2016

By Hee-suk Yun, Dae-jin Hwang, Jeong-woo Seok, Myoung-mo Kim

"In this paper, the accuracy of the data measured by a newly developed displacement measuring system, DPRMs (Digital Pile Penetration and Rebound Monitoring system) and its applicability as a quality control tool were verified by field measurements of pile penetration and rebound for pile driving performed at 3 construction sites and 1 test site. The DPRMs data were found to be much better than handwork data. A new dynamic formula for pile capacities is proposed uses the results of a pilot dynamic load test and the final pile penetration. The ratios of pile capacities obtained by the new formula to those by the dynamic load test were 94%±7.4% in the contrast with 123±28.3% by the 5S formula and 68±24.0% by Hiley's formula. This result shows the superiority of the new formula. The ratios of the maximum compressive stresses calculated by using DPRMs to those calculated by using PDA (Pile Driving Analyzer) were about 90-110±10%. This result confirms the applicability of DPRMs as an overdriving monitoring tool. Two sets of DPRMs were used to measure the 3-D displacement behavior of a pile head at the test site. The more the pile head moves laterally, the less the final set values were expected because of the loss of driving energy, but this trend was not obvious within the limited data obtained at the test site.INTRODUCTIONPile construction monitoring consists of two parts. In the first part, enough capacity of the pile is secured to stand the design load. In the other part, pile damage during driving is prevented. Although several methods can be applied to achieve the first part, PDA is nearly the only tool for measuring pile stress.Several methods such as a static load test, a dynamic load test, an Osterberg cell, and numerous driving equations can determine the pile capacity. Among them, the static load test and the dynamic load test are most widely used. The static load test is advantageous because it has the highest reliability. The disadvantages are as follows: it is costly and time-consuming. Also, the capacity of the pile under construction cannot be evaluated. The dynamic load test has lower reliability than the static load test, but it is cheaper than the static load test, is reliable enough to determine the pile capacity, can evaluate the capacity of a pile during construction, and can offer information about construction conditions such as the pile integrity and the pi le stress during driving. The dynamic load test takes a relatively short time and is low cost compared with the static load test. However, it is still costly, time-consuming, and unnecessary to apply to all piles in the field as a construction measurement tool. Therefore, driving resistance (blowcounts) is commonly measured to confirm the pile capacity at construction sites."

Jan 1, 2005

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By George Filz, Morales, Carlos, Bertero, Filippo Maria, Alessandro, Leoni

"The Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils for many practical applications. A pre-construction soil investigation campaign is necessary to assess soil properties and to retrieve samples of different soil layers for a laboratory Bench Scale Testing program (BST). The BST has to be designed using various binder types, binder contents, and water/cement ratios in each of the soil types. Following the laboratory program, a full scale Field Test (FT) is typically necessary to verify the results of the BST. This paper will highlight the differences and the importance of performing both pre-construction laboratory tests and field tests to ascertain the proper mixing parameters in the different soil layers. Comparative analyses and interpretations between the lab and field stages, along with accumulated information about soil properties and quality control (QC) results, allow fine-tuning the production parameters throughout a project. Three Deep Mixing Method projects, where both laboratory and field tests were executed, are illustrated: (1) The LPV 111 Project (New Orleans, LA, USA): DMM was used for ground improvement/foundation strengthening to stabilize and support the burden of a new levee raise; (2) The Rio Puerto Nuevo Project (San Juan, PR, USA): DMM was applied to improve the soils adjacent to a 90"" forced sewer main relocation and to improve the soils for the base of a new drainage channel; and (3) State Road 83 (US 331) over Choctawhatchee Bay project (Walton County, FL, USA): DMM was applied to stabilize the causeway sections of the bridge enhancement project. Data recorded during laboratory and field tests for these projects were analyzed and interpreted to select the most appropriate construction parameters to provide a final high-quality product.INTRODUCTIONThe Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils in many situations. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product.Generally a pre-construction soil investigation campaign has to be performed to assess soil properties and to retrieve samples of different soil layers for the laboratory Bench Scale Testing programme (BST). The BST has to be designed using various binder types, binder contents (or cement factors - CF), and grout water/cement ratios (W/C) in each of the soil types; the selection of the different combinations and dosages for the BST is based on past extensive experiences on similar materials. Following the laboratory programme results, a full scale Field Test (FT) has to be designed and executed, installing several DMM elements to verify the results of the BST and fine tune the construction parameters, with the appropriate binder type and dosage and the most effective equipment and tool configuration."

Jan 1, 2015

By Suthan Pooranampillai

Verification of drilled shaft resistance is primarily obtained through the use of different load testing methods. Procedures utilized include conventional top down static loading, the Osterberg load cell (O-cell) test and dynamic tests such as the Statnamic method. The O-cell test provides a means of obtaining separately the base and side shear resistance behavior of drilled shafts (cast-in-drilled-hole). Alternatively, the Statnamic load test method enables the engineer to derive base and side shear behavior separately, based on measurements of load, accelerations and strains along the length of the shaft. However, due to time and cost constraints these tests can only be performed on selected shafts within a project. Post grouting of a drilled shaft base embedded within a cohesionless material, with a low mobility compaction grout, will essentially pre-load the shaft base soil against the side shear and self-weight in much the same manner as an O-cell load test (when the load cell is placed within the base vicinity). Therefore, successful post grouting of a drilled shaft would enable verification of both shaft side shear and base resistance simultaneously on each and every shaft it is carried out on. Additionally, such post grouted shafts display stiffer load-displacement response during subsequent downward, superstructure induced, loading compared to ungrouted shafts. Verification of resistance on each and every shaft through the use of post grouting will allow an increase in resistance factors (reduction in safety factor) used in the design. Two 6 ft. diameter drilled shafts were constructed in Fredonia, WA, for WSDOT, each with an approximate length of 52 ft. The shafts were terminated within medium dense poorly graded silty sand. Statnamic load testing of the shafts indicated maximum derived static side shear and base resistances of 2545 kips and 507 kips (1.6 in. displacement) for shaft One and 2466 kips and 212 kips (1.4 in. displacement) for shaft Two. Shaft Two was subsequently grouted, with a low mobility compaction grout. Shaft base mounted total earth pressure cells measured a maximum sustained pressure of 55.44 ksf during the compaction grouting operation. Shaft displacement reached 0.65 inches in the upward direction at termination of grouting. Comparison of grouting data with initial load test information indicates that properly instrumented post grouting verifies shaft base and side shear resistance. In addition, these grouting induced resistances were much higher than design values supplied by the engineer using conventional resistance factor design. Large scale laboratory testing also shows that base grouting verifies higher soil resistances than permissible in conventional design.

Jan 1, 2010

By Patrick K. Wong, Richard Kelly

"The variability in strength and compressibility of in situ deep soil mixing products can be greater than the variability of the natural soil. However, satisfactory performance can be achieved by careful construction and an appropriate QA/QC program. This paper presents a case study on the use of deep dry soil mixing columns to support several embankments over soft clay along a highway project. Post-construction settlement monitoring indicated that good performance is achieved where the acceptance criteria are met, except in an area with high organic content. Embankments with contrasting performance are compared to the quality control test results which comprised laboratory testing of core samples as well as in situ test results such as pull-out and push-in vanes and conventional cone penetration tests. Drawing on the performance results and quality control testing, discussions and guidelines are given on quality assurance acceptance criteria and construction control testing regime for future projects.INTRODUCTIONBetween 2008 and 2012, the largest deep dry soil mixing (DSM) contract during that time in the southern hemisphere was carried out for the Ballina Bypass project. The project, comprising 12 km upgrade of the Pacific Highway located in northern New South Wales close to the border of Queensland, was commissioned by the Roads and Maritime Services (RMS) of NSW. The ground improvement contractor was Keller Ground Engineering (KGE) Australia. Seven different types of ground improvement techniques were employed for the project, ranging from low embankment strategy with nominal preloading, to surcharge with wick drains, light weight bottom ash fill, DSM, vibro-replacement stone columns, dynamic replacement, and vacuum consolidation (installed by Menard Bachy Pty Ltd). Different techniques were chosen depending on time program, cost, and performance requirements relative to proximity to piled structures (e.g. bridge abutments) and post-construction settlement and differential settlement for either rigid or flexible pavements at different locations.DSM was the most utilized ground improvement technique employed on the project, comprising a total of about 285 km of 0.8 m diameter columns to depths up to 18 m for the purpose of supporting bridge approach embankments and culverts with embankment heights up to 6 m. DSM was chosen due to the very soft nature of the clay soil with moisture content practically at liquid limit, and the relative speed and economy of the system. Dry cement powder at rates of 160 kg/m3 to 200 kg/m3 were pneumatically discharged via the hollow stem of the mixing tool, and mixed with the soil (using multiple horizontally mounted paddles on a single vertical stem) at high speed as the mixing tool is withdrawn."

Jan 1, 2015

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By Konstantin G. Ashkinadze

The paper considers performance of piles supporting transient pipe anchors in heavy industrial pipelines. Events such as pump trips or opening and closing of large valves produce short-term dynamic pulses in the pipeline with variable spectral characteristics. Their magnitude is large enough to cause major damage to the pipeline and its anchors, which face horizontal impact loads amounting to hundreds of kN. Design of pile foundations supporting these anchors is often governed by limitation of deflection of the support to prevent overstressing pipeline connections and equipment nozzles. The maximum deflection does not always correspond to the largest load because the stiffness of the soil surrounding the piles heavily depends on the rate of loading. Faster actions encounter stiffer soil response while loads of smaller magnitude applied slowly may be more critical for the deflection time history of the anchor. A typical transient action has both high- and low-frequency harmonics, which makes the response complex. Using load rate-dependent p-y curves published in literature, the paper develops methods of analysis of pile foundations for transient anchors. Pile displacement amplitude – input frequency – natural frequency correlations and time histories of pile response are constructed for typical profiles of transient actions, considering nonlinear soil response to large horizontal loads.

Jan 1, 2016

By Brandon Buschmeier, Frederic Masse

"Inclusions are a type of ground improvement that provide an improvement of a soil mass by insertion of a material with better characteristics than the surrounding soils. There are primarily two types of inclusions: “Soft” inclusions which are constructed of granular material (Stone Columns, Rammed Aggregate Piers, VibroPiers...), and “rigid” inclusions which are constructed of grout inserted with or without pressure (VibroConcrete Columns, Controlled Modulus Columns, Soil Mixing Columns).While the central principle of the inclusions is similar (i.e., overall improvement of characteristics of the soil mass below the structure), the load transfer mechanism is radically different for each technique. Therefore, the applicable design methodology is specific to the type of inclusions and there exists no universal method of design which spans across all inclusions.This paper will present an in-depth comparison between the standard design methods used for “soft” granular-type inclusions (Priebe modified, Balaam & Booker, Goughnour & Bayuk...) and the methods used for “rigid” inclusions which mainly rely on finite element analysis. The paper will explain why the design for soft inclusion methods cannot be applied to rigid inclusions and vice-versa. Each design method will be reviewed in detail to better emphasize its limitations and advantages.Two case histories will also be presented; one for each type of inclusions in order to illustrate the concepts developed in the first part of the paper.1 INTRODUCTION1.1 GENERAL OVERVIEW OF GROUND IMPROVEMENT WITH INCLUSIONSThe use of ground improvement methods to provide the appropriate amount of foundation support is a growing and constantly evolving industry. Traditional structural foundation methods including ‘shallow’ and ‘deep’ foundations do not adequately address the wide range of settlement tolerances, soil conditions, and loading considerations inherent to each unique potential project. In some instances, ‘shallow’ foundation solutions are simply not feasible due to soil and loading constraints. Furthermore, ‘deep’ foundation solutions are used to ‘bridge’ the soft compressible soils, ensuring that the entirety of the load in the structure is transmitted through individual elements into competent layers below the ground surface (bedrock, dense residual soils). Highly concentrated structural loads are transferred into the individual elements by means of direct contact requiring the use of structurally rigid surficial components (structural slabs, grade beams, and pile caps).Ground improvement bridges the gap between these two traditional methods, offering adequate foundation support while using more costeffective techniques and design methodologies. Inclusions are a type of ground improvement used to provide a reinforcement of the soil mass through the vertical insertion of a material with better characteristics than the surrounding soils. Much like deep foundations, inclusions are installed through soil layers with high compressibility and/or low bearing capacity and terminated in a suitable bearing stratum. However, unlike deep foundations, ground improvement inclusions rely on a distribution of load between the soil and the inclusions. By doing so, some of the structural load is applied directly to the soil in a proportion equal to its bearing capacity and compressibility limits, while the rest of the load is shed into the vertical inclusions down to the bearing stratum. Load sharing is a critical aspect in the performance and design of the various ground improvement methods."

Jan 1, 2015

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By Marco D. Boscardin, Benjamin H. MacKinney, Kenneth R. Allard, Kenneth A. Pidgeon, Adriane G. Boscardin

This paper presents a case history for a unique application of a system of vertical micropiles with horizontal soil nail bracing and shotcrete facing for underpinning. The system was used to support and protect an existing 2-story hospital building during demolition and renovation. The goal was to limit building movements and have the building remain in use during construction of an abutting addition. Soils at the site consisted of clean, loose to dense, sand and gravel. The original underpinning design was revised after the initial excavation revealed unsuitable soil conditions for traditional underpinning pits. An alternative system consisting of vertical micropiles (hollow bars) through the footing, combined with shotcrete and soil nails was proposed, accepted by the owner, and successfully constructed. Excavation depths were up to 15 feet (4.6 m) below the existing footings. Wall movements were monitored at regular, horizontal and vertical intervals along the hospital wall, and less than 0.6 inches (15 mm) of settlement and 0.1 inches (3 mm) of horizontal displacement throughout underpinning and construction were reported. The challenges with the original proposed support of excavation design and other alternative approaches considered will also be discussed.

Oct 1, 2022

By Janaka J. Kumara, Takashi Kurashina, Yoshiaki Kikuchi, Takahiro Yajima

"The inner frictional resistance of open-ended piles depend heavily on the degree of soil plugging. Many factors including pile diameter, relative density and end conditions of the piles influence the degree of soil plugging. In this paper, the effects of inner sleeves attached at the pile base on the inner frictional resistance are discussed. The experiments were conducted on a medium-dense sandy ground using smallscale model piles. The results suggest that the inner frictional resistance is influenced by sleeve height for 50 mm diameter piles although it is independent for 30 mm diameter piles. The results also indicate that soil plug height is influenced by the sleeve height. The results of the incremental filling ratio (IFR) showed that penetration of non-sleeved piles is closer to unplugged state than the sleeved piles. The results of the IFR also reveal that the degree of soil plugging is affected by the sleeve height for 50 mm diameter piles although the variation is very limited in 30 mm diameter piles. The results on the coefficient of lateral earth pressure suggested that it increases from 1.08 – 1.75 when the sleeve height is increased from 10 – 100 mm for 50 mm diameter piles.INTRODUCTIONPrevious studies have shown that the behaviour of open-ended piles is different from closed-ended piles (Szechy, 1961; Randolph et al., 1979; Paikowsky and Whitman, 1990). Open-ended driven piles are widely used for deep foundations, in particular in offshore deep foundations. Generally, it is accepted that a short open-ended pile produces a smaller bearing capacity than a similar closed-ended pile (Nauroy and Tirant, 1983). However, a long open-ended pile can produce a similar bearing capacity as a closed-ended pile due to a large inner frictional resistance mobilised between the inner pile shaft and inner soil (Lehane and Randolph, 2002). The ultimate bearing capacity of an open-ended pile, Qu consists of three components as given in Eq. 1."

Jan 1, 2017