Search Documents

By Vasileios A. Drosos

The response of pile foundations to lateral loads is an important factor for the successful performance of several critical structures. A new numerical code for the analysis of single piles under lateral load is outlined. The code can simulate (through appropriately chosen parameter values) not only the non-linear behavior of soil, but also the inelastic structural response of the pile itself under lateral load. Emphasis is given on the calibration of model parameters and the verification of the code. For the calibration of the parameters, data is used (a) from the well documented in the literature p-y curves, and (b) from experiments conducted either in full scale or in the centrifuge. Results are compared to those of well known published codes for inelastic analysis of single piles under lateral load.

Jan 1, 2006

By Zhang Jiaju

For the highrise buildings with deep foundstion of irregular plane shape, an appropriate calculate model to the heave of foundation soil after excavation is proposed and studied using analytic method and FEM (Finite Element Method) respectively to provide an effective way for solving this kind engineering problem. Also combined with the practice of construction deep foundation of Capital Mansion, calculation of the heave of foundation soil after excavation is given. Compared these results from above two methods with the results measured in situ, it is conformal on the whole, and the results by FEM are much closer with the measured.

Jan 1, 1991

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By C. L. Liao

The chief experiences for constructing deep tubular columns foundation under deep water are as follows: 1. P.C. tubular columns were sunk inside the caisson. 2. P.O. tubular columns of 3.6 M. diameter were sunk thru thick soil layer to a depth of 47 M. by vibrators. 3. The double wall steel cofferdam was sunk thru soil layer to a depth 31.3 M.. 4. Bore the bedrock with rotary drill succesfully. According to the successful experiences mentioned above, the deep tubular columns foundation may be constructed beyond 100 meters.

Jan 1, 2010

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By Amaneh E. Kenarsari

Among the different sources of uncertainty in pile bearing capacity prediction including inherent heterogeneity, measurement and model uncertainties, the inherent heterogeneity of soil properties is of particular interest and is considered in this study. Cone tip resistance data are utilized to calculate pile bearing capacity by considering vertical soil variability. In this regard, cone tip resistance component of CPT data is assumed as a random parameter. Realizations of this parameter are achieved with the aid of local average subdivisions and random field theories. Monte Carlo simulation is used to generate different realizations of CPT or CPT-u data. Pile bearing capacity was then calculated by the use of direct method. Pile bearing capacity are predicted for a project in south of Iran using this method and probability density function for the total bearing capacity of pile is plotted. Coefficient of variation of 33% for ultimate bearing capacity shows the variability of bearing capacity due to variation of soil strength in depth. Cumulative probability chart for the ultimate bearing capacity are plotted as an efficient tool for estimating ultimate bearing capacity of piles with different desired confidence levels for vertically variable soil strength properties. Significant difference between mean value of pile bearing capacity (18 MN) and limit with 95% confidence level (8 MN) emphasizes the importance of considering soil variability.

Jan 1, 2011

By Y. Duraisamy

This paper presents the compressibility of tropical peat reinforced with cylindrical cement column. When a cement column installed vertically in peat, its compressibility was reduced because of the hardened skeleton matrix formed by cement particles bonding with adjacent soil particles in the presence of pore water. The effects of diameter, number of columns and cement proportions in cement columns on the compressibility have been investigated in this study. The results indicated that compressibility index Cc and Ca decreased with the increase in diameter of the cement column. Specimens with 45 mm and 60 mm diameter of cement column were cured for 28 days, after which they were subjected to Rowe Cell Consolidation test. Based on the results obtained, it shows that cement columns can successfully reduce the compressibility of tropical peat.

Jan 1, 2007

By Michael D. Justason

"In January 2009, long-time competitors, Anchor Shoring & Caissons Ltd. of Toronto and Bermingham Foundation Solutions of Hamilton, joined forces to tackle one of the Greater Toronto area’s largest deep foundation projects: the West Toronto Diamond Rail Grade Separation. The two companies formed the “West Diamond JV” and succeeded in winning the contract from the Canadian National Railways. This deep foundations work was the first and most significant part of the $300-million-plus rail grade separation project. A big part of the job turned out to be dealing with local government regulations and citizens’ concerns with noise and vibration.The project is approximately 10 km (6 mi) northwest of downtown Toronto in an area of mixed-zoning including light industrial, commercial and residential buildings. The area is commonly called the “The Junction,” because of the heavy rail- traffic. The “West Toronto Diamond” refers more specifically to the railway junction where the North-South tracks of Canadian National (CN) Railway meet at a level crossing with the East-West tracks of the Canadian Pacific (CP) Railway. The goal for this part of the project was to convert the West Toronto Diamond into a grade-separated junction by depressing the CN lines under the CP lines, thus allowing commuter rail carrier, called GO Transit, intercity carrier VIA Rail, and CN freight trains to pass through the new underpass.Dawn Tattle, president of Anchor Shoring & Caissons says, “not only is the site in a densely populated area adjacent to homes and businesses, the crews worked adjacent to active rail lines with numerous trains passing daily. During the 7-hour working day, approximately 60 trains passed through the site in very close proximity to working crews.” Safety was paramount. While trains were passing through the site, it was a railroad requirement that all equipment and men stop working. In addition, at those times, all personnel were required to stay 6 m (20 ft) from the tracks and were required to face the tracks. For the faster commuter trains, this work interruption could last as little as 2-3 minutes, while interruptions caused by the slower freight trains could last as long as 25 minutes. The most disruption to the site occurred during the morning commute between 7 to 9 a.m., so work did not really get underway until after that time. Once work finally commenced the race was on to finish as much as possible before the afternoon commute – hence the shortened work day. The amount of disruption caused by the trains was a big unknown faced by the JV going into the project, but crews adapted quickly to the very unusual work environment"

Jan 1, 2012

By Y. C. Han

The advances in seismic design considering soil-structure interaction or soil-pile-structure interaction are described using a substructure approach. The nonlinearity of soil is considered approximately using a boundary zone model with non-reflective interface, and computer programs are available for practical applications. The validation of model is confirmed with dynamic tests on piles in the field, and the results for a single pile are used to compare with the predictions in this study. The liquefaction for sand soil layer can be accounted for, and a case of liquefaction is discussed. Two practical examples are examined, a vacuum tower structure supported on foundation of steel pile group and a table top structure supported on foundation of concrete pile group. To illustrate the effects of soil-pile-structure interaction on the seismic response of vacuum structure, different base conditions are considered, rigid base, i.e. no deformation of the foundation; linear soil-pile system; and nonlinear soil-pile system. The method introduced can be applied to the design of tall buildings, bridges, industrial structures and offshore platforms with soil-pile-structure interaction under seismic or dynamic loads.

Jan 1, 2010

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2000

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By Kenneth Gavin

Design practice for piles installed in Irish glacial till has developed in an ad-hoc manner, based on the results of un-instrumented load tests. This had led to designers using similar design parameters for both CFA and displacement piles. To address the concerns of industry a series of instrumented pile tests were performed by two Irish Universities. These tests summarized herein, revealed that CFA piles develop higher shaft resistance than piles driven in glacial till. However, they exhibit low base stiffness and the end bearing resistance that can be mobilized at acceptable pile settlement is low. The use of simple non-linear elastic design approaches to predict the load-displacement response is considered. The methods are used to predict the capacity of two large diameter CFA piles installed in glacial till. While the predictions were reasonably accurate at predicting the initial load-displacement of the piles, significant creep settlement developed at higher load levels. The cause of the creep settlement was investigated through the use of plate load tests and the consequences for pile design are discussed.

Jan 1, 2009

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By Dan Brown

A method is outlined for computing the contribution of a micropile group to global stability of a sliding mass. The forces in the micropile are computed in a way which accounts for the effect of soil mass movement on the mobilization of axial and shear forces and which maintains compatibility between shear and axial force as a function of displacement. The method provides a rigorous model to incorporate the pile forces into the stability calculations, including the effect of pile forces on the resultant shear and normal forces at the sliding surface. This paper demonstrates the proposed solution using a simple example slope.

Jan 1, 2007

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Chris Sammon

The Block 75 portion of the City Creek redevelopment project in Salt Lake City required multiple shoring walls surrounding the 6 acre site constructed to depths ranging from sixty-five to ninety feet below original street grade. Shoring for the project was challenging due to site soils consisting of cobbles, sands and gravels, interlayered lakebed silty clay and fine sandy silt with incised stream deposits of silty/clayey sand and gravels combined with a high groundwater table. Moreover, several abutting structures each with a unique foundation system would be directly or indirectly supported by the shoring system. Three sections of interest are the shoring walls constructed at Main Street, Deseret Trust Building and Eagle Gate Tower. Main Street shoring extended to as much as sixty-five feet below street grade and utilized existing basement walls anchored in place in the upper zones with soil nail walls with pre-installed vertical elements for face stabilization below. Data are presented which illustrates the effect dewatering had on the settlement of the Main Street Shoring. The Deseret Trust Tower shoring supported a 12 story, historical masonry building. Site conditions dictated a separate design for the east side and the north side of the building allowing comparison of relative performance between these walls. Settlements of this structure were controlled by installing micropiles through the 90 year old structures spread footings. Shoring for the Eagle Gate Tower was to be constructed immediately adjacent to a mat supported 22 story high rise structure. This shoring system combined secant piles, ground anchors and incorporated existing abandoned-in-place pipe piles with infilling high pressure jet grouting to create a cutoff wall and eliminate the adverse impacts of dewatering below this sensitive foundation.

Jan 1, 2010

By Camilla Favaretti, Benjamin Turner, Anne Lemnitzer

Pile foundations are extensively used in the construction of various types of superstructures, including tall buildings, bridges, freeways and offshore structures. A fully constrained tip embedment such as a rock-socket offers an attractive solution for achieving significant tip resistance and improving the load-carrying capability of the foundation element. In profiles with very soft surficial soil, rock-socketing often provides the only reliable source of axial and lateral resistance. In preparation of a large-scale testing program on rock-socketed piles at UC Irvine (UCI) geared towards studying the magnitude of shear amplification at the rock-soil boundary of pile foundations, a pre-test model-scale experiment was executed in the UCI Structural Laboratory. The objective of the model-scale experiment was to iterate and validate the test setup, study the influence of important boundary conditions, assess instrumentation techniques and sensor placement, and to gain preliminary insight into the small-scale specimen non- linearity. In addition, this model-scale study provides ample opportunity to compare lateral performance parameters with analytically predicted lateral load behavior using traditional soil resistance functions and limit state analyses and explore new techniques for the derivation of soil resistance functions. The pile specimen had a pile diameter (D) of 10 inches and a total pile length of 125 inches. The pile was embedded in a 40 inch simulated rock socket overlain by 52 inch of medium dense sand (DR~50%). The pile extended 32 inches above the soil surface, where cyclic lateral loading was applied. The pile was installed in a laminar metal frame box with inside dimensions of 39 inches in width (W), 73 inches in length (L) and 86.1 inches in height (H) as shown in Figure 1. During testing, the box was restrained using a rigid bracing system consisting of concrete reaction blocks, wooden braces and steel girders.

Jan 1, 2018