Search Documents

By Dan Brown

This paper presents a case study of a cyclic lateral pile load testing program performed on two 18-in square prestressed concrete piles (PSC) in Savannah, Georgia. The load test program was developed to simulate the lateral behavior of a single pile under seismic loading conditions for the design and construction of a large LNG storage tank. The lateral load tests included cyclic loading to measure possible degradation in soil response followed by static loading to large displacements (around 6 inches at the loading point). The lateral load was applied through a reciprocating jack positioned to push and pull the piles against each other. The test piles were instrumented with multiple displacement transducers, downhole inclinometer, and strain gauges. This paper provides an interpretation of the test results regarding the pile performance and soil response to monotonic and cyclic lateral loading. A backfitted computational model of the soil resistance was developed to match the test results using the LPILE computer program. The load-deflection and deflection/moment versus depth comparisons suggest that this model appears to capture the behavior relatively well within the general range of suitability for design purposes. New design curves were developed based on the soil parameters derived from the lateral load test results.

Jan 1, 2003

By P. Arz

With a total of five basement levels, ground floor and a further six levels above grade, construction of the Kö-Galerie building, on the Königsallee, in the centre of Düsseldorf, was completed with all the difficulties which accompany property development today in the inner city. To meet the intermediate and final deadlines, ad­vanced building techniques were used. Notable among them are the top/down method for simultaneous construction upwards and downwards from an intermediate level, and the use of pre-fabricated composite columns in drilled shafts for the main load-bearing foundations as well as diaphragm walls designed as permanent structural wall of the basement.

Jan 1, 1989

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By Tomohide Takeyama, Yuki Yoshida, Masaki Kitazume

"Abstract A series of centrifuge model tests was conducted to investigate the failure pattern and stability of cement treated clay ground having an unsupported vertical slope. The model ground was subjected to monotonically increasing centrifugal acceleration until it failed due to the enhanced self-weight. The test results were compared with the numerical analyses in which the treated soil was simulated by the Smoothed Particle Hydrodynamics (SPH) method. In the simulation, the Dracker- Prager model is employed as the constitutive model. In order to simulate the brittle behavior of the cement treated soil, it is assumed that the unconfined strength is gradually reduced to a certain value which corresponds to the residual strength due to accumulated plastic strain. It was found that the simulation by using SPH method can express the brittle failure observed in the centrifuge model tests.IntroductionBecause of economical and environmental concerns it has become more difficult in recent years to obtain enough soil to construct reclaimed land for airports, electric power plants, manufacture plants and so on. On the other hand, it has become difficult to find and construct disposal sites for waste subsoil or dredged soil. These circumstances have encourage geotechnical engineers at present to use these poor quality materials as filling materials more than they were used one or two decades ago. Several soil admixture methods have been developed to improve their properties and to manufacture high quality fill materials.The deformation and strength characteristics of cement treated soils have been investigated in Japan, which have revealed that the treated soil is characterized by a brittle behavior with quite high compressive strength and quite small strain at failure, and the treated soil with relatively high strength shows tensile failure instead of shear failure. Regarding to evaluate the stability of structures adjacent to or buried in the treated ground, Kitazume (1998) and Kitazume et al. (2003) investigated the earth pressure of cement treated ground by the centrifuge model tests. And they emphasized that the failure pattern of the cement treated ground was much different from that of ordinary ground. After the Hyogoken- Nambu earthquake in 1995, many design codes for the seismic stability were revised in Japan, so that seismic stability must be evaluated more precisely. The dynamic earth pressure of ordinary grounds is usually calculated by a pseudo-static limit equilibrium method based on the Mononobe- Okabe’s method (Okabe, 1924; Mononobe and Matsuo, 1929). This calculation method is also applied to the cement treated ground, although its applicability has not been thoroughly clarified."

Jan 1, 2014

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibration limits for buildings with respect to ground vibrations from pile driving published in international standards are reviewed. At first, relevant vibration parameters are defined and the evaluation of vibration records is described. The sensitivity of structures to different vibration parameters (displacement, velocity and acceleration) is discussed. Most vibration standards relate to blasting activities, the dynamic characteristics of which can be significantly different to those from construction activities and in particular, pile driving. Several vibration standards are reviewed. The Swedish vibration standard is described in detail, as it is the only one accounting for several important factors, such as ground conditions, building material, and type of building foundation. Many standards limit the guidance to values based on the dominant vibration frequency and a wide scatter of frequency-dependent vibration limits exists. It is difficult to compare limiting values of ground vibrations proposed in different standards.1. INTRODUCTIONFor poor ground conditions, placing structures on piles is the most common foundation solution, while sheet piles are widely used to support deep excavations. Piles and sheet piles must often be installed in the close vicinity to buildings, structures or installations in the ground, which can be affected by ground movements and vibrations, (Massarsch and Fellenius, 2014). In many areas, environmental concerns with respect to noise and ground vibrations can restrict or even prohibit driving of piles or sheet piles or reduce the efficiency of installation. The design engineer must prescribe – often at an early stage of a project — the permissible levels of ground vibrations in order to minimize the potential risk of building damage. When seeking guidance from the literature, little or practically no applicable information can be found on how to assess permissible levels of ground vibrations."

Jan 1, 2014

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By B. Broms

The "Bawang Pile" (in english "onion" pile) described in the article consists of a cased concrete shaft and an expanded base. The steel casing is first driven by an internal drop hammer and then the base is formed in-situ by the raming the concrete at the bottom of the slitted casing. This new type of pile can be used for underpining (small head room) of buildings and as foundation for transmission towers or lamp posts. Full-scale load tests in compression and in tension on the Bawang pile and on steel pipe piles demonstrate the dramatic increase of the ultimate capacity due to the expanded base. Guidelines for the design of such piles are proposed.

Jan 1, 2010

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By SungWon Park

The efficiency of the current design methods for computing pile resistances is evaluated using field load-settlement tests results. Twelve load-settlement test data for drilled shafts and bored piles were obtained from the literature. These load-test data were fitted using the ?t-z? method. Subsequently, the ultimate resistances were evaluated based upon the failure criteria from following methods: (1) the Davisson?s approach and (2) settlement corresponding to 5% or 10% shaft diameter approach. The ultimate resistances for these drilled shafts and bored piles were also predicted using methods based on the design code from North America (United States, Canada), Europe, and Asia (Japan). The pile resistances determined from field load-settlement tests were compared with those calculated using the design codes. The comparisons show that most design codes predict a conservative resistance for drilled shafts and bored piles. However, in the case of drilled shafts, we find that some of the design codes can over-predict the resistance and, therefore, should be applied cautiously. This research also shows that ?t-z? method can be successfully used to predict the ultimate resistance and the load transfer mechanism for a single pile.

Jan 1, 2009

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2002

By John W. M. Lambert

This paper describes the execution and the results of a new method to seal off leaks in water retaining constructions. The new method, called BioSealing is based on activating the bacteries, present in soil and groundwater. The method was tested under field conditions in 2004 and applied at the HSL aqueduct of the 'Ringvaart Haarlemmermeer' in 2005.

Jan 1, 2006

By J. Matos e Silva

"Abstract The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the ones obtained by using the Eurocode 7 and the Portuguese Norm related to the EC7 (NP EN 1997-1 2010), as the Eurocodes consider the possibility of each European country to adopt their own geotechnical parameters as these may vary from one country to another. A comparison is also made with the behaviour of these diaphragm walls during its construction phase; so the values from the design that were adopted in the construction are listed in tables 2 to 6 in the “Construction Options” columns. From the referred examples the author presents his conclusions.1 - INTRODUCTIONIn the so-called “traditional criteria” the soil parameters (dry unit weight, angle of internal friction and cohesion) have values obtained through tests or empirically. It is assumed that the characteristic values of the soil parameters adopted in Eurocode 7 are equal to the soil parameters adopted in the calculations by the “traditional criteria”. In the present paper the design according to the EC7 was made considering only the ultimate limit states and the respective Cases A1 and A2.The partial coefficients used for the actions in the present paper were those on Table 1:2 - CONSIDERED EXAMPLESThe five examples correspond to the situations of figures 1 to 5, and the respective results are summarized in tables 2 to 6.For all the considered examples, that are case histories, a simplified method published by Matos e Silva (March 2000) was adopted. This method attains good performances when compared with other more sophisticated ones as the finite elements and the elasto-plastic methods as described in a paper published by Matos e Silva (2000). All the obtained values were compared between them and with the so-called “Construction Options” that were the values adopted by the designers of the considered examples. For the wall bottom length calculation two possible situations were envisaged:"

Jan 1, 2014

By Scott White, Pishun Tantivangphaisal, Andrew Bell, Chris Barker

There has been considerable advancement in recent years in the tools, both software and hardware, available to allow efficient digitalization of site records during the construction of geotechnical works. Whilst these tools have excelled at replacing handwritten records, the ability to use digital records to validate design and construction requirements in real time or even within reasonable timescales has generally been limited to the development of bespoke ‘prototype’ project specific solutions. This paper describes the development and implementation of an industry standard design schedule and the benefits of the broad adoption of a single database schema for data recorded on geotechnical sites. The former has brought significant improvements and automation of the design process, whilst the latter has enabled the validation of the constructed works against design intent in almost real time. Further details of the standardized design schedule, already publicly available in the UK through the FPS, examples and lessons learnt from implementing digital site record systems on live projects are presented herein. The utilization of cloud computing technology and complex algorithms linking plant/rig instrumentation with design data can further automate construction sites using IoT (Internet of Things) best practices. The authors will share their experience of the recent deployment of a digitalized design-to-construction record system, give recommendations for future development and a call for an industry wide drive to finalize and adopt the AGS Piling data schema.

May 1, 2022

By Joseph A. Sopko

There has been a trend in recent years in performing the initial formation freezing using liquid nitrogen (LIN) and then converting the system to circulating refrigerated brine. While proponents of this method state it decreases freezing time, it can also be considered an alternative to inadequate refrigeration capacity. This method was used on several small projects in the 1980s. Problems such as broken pipes, frozen brine, and unsafe work conditions caused contractors to re-think the method. This paper discusses these problems and also presents work schedules showing no schedule reduction. In fact, this method can lead to longer time as well as significantly higher costs. BACKGROUND Ground freezing as a method to provide groundwater control and temporary earth support for excavations is completed using a relatively simple process: drilling and installing refrigeration pipes around the perimeter of the excavation and introducing a coolant into these pipes. The coolant extracts heat from the ground, converting the pore water to ice and forming a strong, impermeable material. A typical ground freezing system is illustrated in Fig. 1. SYSTEMS There are two basic types of coolant systems: circulating and direct expansion. The circulating coolant system is made of two separate, closed systems. The medium circulating is the secondary coolant. It is cooled at a central refrigeration plant, circulated through the pipes, and warms as it extracts heat from the ground. It then circulates back to the plant where it is cooled. This coolant is chilled in a heat exchanger by the primary refrigeration system where a compressor system is charged with a refrigeration gas. The heat is ultimately extracted from the ground and expelled into the atmosphere by an evaporative condenser. Secondary coolants are usually a brine or glycol chemical while the primary refrigeration gas is anhydrous ammonia or another commercially available gas.

Jan 1, 2019

By Brian Langdon

The DRIVEN GROUT PILE was developed in 1989 by DeWitt Construction, Incorporated. This piling essentially consists of a cost-in-place concrete piling that reacts on a steel boot that is driven to bearing. This report will describe the driven grout pile, its background and its installation. The advantages and disadvantages of this system are also discussed. Finally, the results of actual field installations are presented and discussed. BACKGROUND The DRIVEN GROUT PILE was developed out of a need for a low-cost high capacity piling (100 ton) that could be installed with ordinary pile driving equipment. This search was motivated by attempting to incorporate the material economy of an auger-cast piling with the "empirical load test" of a driven pile. Typically, the least cost material for piling in the 100 ton range is concrete (grout). A grout shaft with minimal reinforcement can withstand a compressive load of 100 tons for a material cost in the range of $6.00 to $8.00 per lineal foot. A pipe piling with a capacity of 100 tons has a unit material cost ranging to $13.00 per lineal foot. The marriage of these two advantages resulted in the DRIVEN GROUT PILE. A pile that utilizes the economy of a reinforced grout shaft and has the loading confidence of a driven pile.

Jan 1, 1990

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Mathew Avery, Colby Barrett

In November 2016, a 7.8-magnitude earthquake caused more than 100,000 cubic meters of rock and debris to tumble down and bury the transportation infrastructure below Ohau Point in New Zealand. All routes between the northern and southern portions of South Island were severed. To undertake the rebuilding efforts, the New Zealand government established North Canterbury Transport Infrastructure Recovery (NCTIR) – an alliance to repair the road and rail networks between Picton and Christchurch. NCTIR’s aim was to have the road open by Christmas 2017, but work also continued into 2018 to complete a number of safety improvements along the highway. The presentation will review the initial remediation attempts, the necessity to re-evaluate the original efforts, the need to incorporate techniques that were “outside-the-box” and different from traditional methods, and the logistics and planning that were required to complete the work safely. INTRODUCTION Shortly after midnight on Monday 14th November, a magnitude 7.8 earthquake struck the small South Island settlement of Waiau in North Canterbury, 100km north of Christchurch. The quake was the largest in New Zealand since the magnitude 7.8 Dusky Sound earthquake in 2009 (GNS 2016). While shaking was widespread with over 15,000 recorded ‘felt reports,’ the worst shaking occurred about 50 seconds after the quake rupturing started. The energy of the tremor progressed north over several minutes with surface rupture recorded on a total of 21 faults. The length of all the fault ruptures combined was close to 100km (GNS 2016). The degree of ground shaking was high, recorded as Modified Mercalli Intensity Scale (MMI) Level 8 – Severe. This level of shaking causes considerable damage in ordinary buildings with partial collapse including fall of chimneys, factory stacks, columns, monuments, walls, etc. At a human level, people experience difficulty standing; while furniture and appliances shift. Geologically, the damage depends on the geological setting. In Kaikoura and the surrounding area, especially the coastal highway State Highway 1, north and south of the town, many of the slopes consist of over steepened weathered, fractured greywacke. During the quake, the shaking caused significant and widespread damage with a total of 26 major slips (and many smaller slips); closing both State Highway 1 and the Main North Rail Line between Picton and Christchurch.

Jan 1, 2018

By Anuj K. Singh, Shuvranshu Rout, Manos De

"Foundation for tracks of coke transfer car and dust extraction pipe was designed as series of isolated foundations spaced at 11.0m along length of coke oven battery resting on soil at depth of 2.5m. In one region the foundations are close to adjacent 12m deep underground junction house. Five foundations in this zone were constructed on backfilled soil without proper compaction instead of engineering soil fill or concrete fill. The foundations settled under loads and the supported frame structure tilted after equipment erection and during trials endangering the safety of the structure and equipment operation. The distorted structure had to be rectified in-situ by arresting settlement. In order to stabilize the foundation and supported structure the supporting soil had to be strengthened in situ without any dismantling, reconstruction and adverse effect to equipment operation. This paper presents the case study on the evaluation of defects for the foundation failure and analysis of the problem, proposed rectification of the situation by appropriate soil stabilization scheme, monitoring of the stabilization operations and verification of effectiveness of the rectification work by measurement of settlements. The implemented solution has ensured safety of the structure and equipment without any adverse impact on normal operation.INTRODUCTION AND BACKGROUNDNew Coke Oven Battery was being installed for an integrated Steel Plant. The hot coke from oven is pushed out after completion of coking process through a coke transfer car onto a hot coke receiving car. The coke transfer car runs on rail track parallel to the line of ovens forming the coke oven battery. One rail is supported on the structure of the operating platform of the battery and the second rail rests on independent structure of track beams. A large diameter pipe for extraction of the dust emitted during coke pushing operation is also supported on the same structure that supports the track beams. The entire structure rests on columns spaced at approximately 11.0m along the length of the battery. The columns transfer load to ground through individual foundations resting on competent subsoil strata.Two sets of foundations for the rail track beam support and dust extraction pipe support are adjacent to deep underground junction house of coke carrying conveyor. The depth of the pit for the junction house is 12m. The layout and arrangement of the foundations in this region around the junction house (JH-1) is shown in the “Figs. 1a, 1b”."

Jan 1, 2017

By M. Cornelius

Drilled shaft construction through caving soils has historically been an uncertain, risky and costly operation. Uncertain, because the zone of caving may or may not be known, risky because the loss of a shaft is disastrous, and costly because the Contractor, who faces these risks, must include large sums of money in his bid for shaft wall stabilization techniques. This case study will discuss the stabilization techniques that are typically used within the United States, and then present new technologies, born in Europe, that are being utilized in the States by Malcolm Drilling Company today.

Jan 1, 1999