Search Documents

By W. Y. Xu

In comparison with shallow foundation, usually higher bearing capacity, smaller average settlement and better stability are the engineering characteristics of pile foundation. Besides, a smaller differential settlement and a lower settlement rate which will converge quickly are more important characteristics. The superstructure of the building with pile foundation may not meet with significant differential settlement. In this paper, settlement records and other data of different kinds of buildings are chosen to illustrate the characteristics of pile foundation. Moreover, some technical problems in connection with foundation engineering solved in consideration of the above mentioned characteristics of pile foundation are also introduced.

Jan 1, 2010

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003

By James S. Graham

Specifications for treated round wood piling are presented for the engineers consideration. Included in the text are background information, technical committees, Chellis, quality, treatment, static and dynamic stresses, accessories, and existing codes and standards. The specifications are also available using Word Perfect on 3.5 or 5.25 inch size disks provided by the National Timber Piling Council. Note: DFI recommended wording is wood, head, and toe, instead of timber, butt, and tip.

Jan 1, 1992

By Q. M. Huang

In 1979 our company undertook the project of infra-structural work of White Swan Lake Hotel, (International class ) Guangzhou. Visit to the site showed that it was situated at the riverside, covering an area of 54,000 M2 with 30,000 M2 of which reclaimed from Pearl River. The material used for reclamation was black sand which was dredged from the nearby riverbed. The sand had the properties of high permeability and very low internal friction. The basement of the building was 6.2 m below ground level and 3 m lower than the riverbed. Apart from the pile foundation, a diaphragm wall was to be constructed prior to the commencement of excavation work for basement. A feasibility study was carried out to determine the method of construction which would maximize utilization of the plants and equipment that were available in the execution of the aforesaid foundation works. This report concerns only the construction of the diaphragm wall and the performance of the plants employed. A detailed delineation of the construction method is herein discussed

Jan 1, 2010

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010

By SungJe Chi

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2017

By Dan A. Brown

The following paper was written by Dr. Dan A. Brown, P.E. Brown is an Associate Professor at Auburn University's Department of Civil Engineering. The paper was originally presented at a FHWA's Transportation Research Board meeting and is presented here with the author's consent. Construction and design of drilled shaft foundations in hard pinnacle limestone requires flexibility from all parties involved due to the variability of the subsurface conditions. This article describes some strategies which have been found useful in the Birmingham, Alabama area. The importance of well trained and experienced field personnel in these conditions is noted. It is also vital that engineers understand the construction challenges so as to provide both quality assurance and cost effectiveness in design and in the specifications.

Jan 1, 1991

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By J. Nakayama

Down-the-hole hammer is commonly recognized as the most powerful drilling equipment for weathered to fresh rock formation including boulders. However, its drilling diameter is restricted by reasons of difficulty to actualize large diameter drillhead and to ensure discharging means of cuttings. Cuttings are usually removed by flushing i.e. uprising return air after compressed air actuates hammer, but in case of large diameter drilling, as the clearance between drill rod and surrounding wall of hole become fairly large, necessary up-hole air velocity to transport cuttings can not be maintained. In case of marine or underwater drilling or high groundwater table, orthodox down-the-hole hammer is obstructed its operation by water. This single head hammer drill combined large diameter drillhead with reverse circulation of drilling fluid enables large diameter drilling extending to 1.5 m, i.e. actualized large diameter mechanical drillhead incorporated with ensured cuttings removal means enabled this range of drilling. This paper introduces its features and actual applications to large diameter bored pile drilling for varied sorts of rocks in maritime construction projects.

Jan 1, 1996

By Lance A. Roberts

Expansive soil formations can be found throughout the United States. When subjected to wetting, these formations have the potential to swell and exert large uplift forces on buildings and foundations. Lightly loaded structures, such as single family residences founded in areas of expansive soils, can be significantly damaged due to uplift movement from swelling actions. Designing an economical deep foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material or the use of drilled shafts can be costly. Piles made from recycled polymer materials could provide a solution. Due to a lower coefficient of friction along the interface of the soil-pile interface compared to traditional pile materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure, which minimizes the risk of significant structural damage from excessive movements. This paper presents the results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity. The remaining four piles were subjected to long-term monitoring of uplift movement during the course of the project. A concrete anchor was also installed at the test site for uplift monitoring. Data gathered during the field and laboratory testing was utilized in a non-linear soil-structure interaction model to predict the displacement behavior and internal stresses within a plastic pile and concrete anchor subjected to uplift forces from the swelling shale. While more research is needed to further understand the application for recycled plastic piles, the results from this research indicate that their use is a viable alternative for support of lightly loaded structures in expansive soil environments.

Jan 1, 2010

This manual provides basic practical instruction on the inspection of driven piles. It covers the essential components of pile driving, such as the pile driving hammer, hammer accessories, the pile and soil, and frequently encountered test methods in an uncomplicated, yet knowledgeable, and practical manner. Insight is given into the methods of installing the foundation, dealing with the cranes which do the lifting, the hammers which do the driving, the leads that guide the hammer and pile, the compressors which provide the external power when required, and finally prevalent analysis tools and testing instrumentation and procedures which enable you, the Inspector, to do your job. This DFI Inspector's Manual for Pile Foundations will help the Pile Inspector who has limited knowledge of pile foundations. Perhaps this Inspector has been pressed into service at a moments notice; a few helpful hints and suggestions to him are desperately needed and he can look here for the basics. It is also useful for the experienced Pile Inspector as a reference guide. However, this manual is not a detailed check list of every possible scenario and detail which could ever be encountered. There are other sources available which give more detailed descriptions (and should be consulted by the Inspector when appropriate; a list of this additional reference material is provided and suggestions made in appropriate chapters of this text). The current manual is more a brief "textbook overview" with some of the more important aspects given at least some emphasis so that the Inspector has some direction and hopefully helps to produce a safe, yet economical, foundation.

Jan 1, 1997

By Rozbeh Moghaddam, William D. Lawson, Priyantha W. Jayawickrama, Hoyoung Seo, James G. Surles

"This study provides calibration of resistance factors (?) for design of driven piles to implement Load and Resistance Factor Design (LRFD) for bridge foundations using Texas Cone Penetration (TCP) Test data. The basic research approach was to compile a database of published full-scale load tests including projects from the Texas Department of Transportation’s (TxDOT) historical archive and projects from neighboring state DOTs. Load test results from neighboring states were leveraged by performing new geotechnical borings with TCP tests at the project sites. The final dataset consisted of 30 load tests performed on precast square concrete piles, with pile widths ranging from 356 to 508 mm and penetration depths ranging from 5.2 to 25.5 m, driven in soils. Ultimate capacities for each load test were interpreted based on Davisson, 5%, and 10% settlement criteria. These measured ultimate capacities were compared against predicted capacities estimated from TCP blow count values (NTCP) and design charts following the procedures outlined in TxDOT’s Geotechnical Manual. From the comparisons, statistical parameters of the biases (??= measured capacity/predicted capacity) such as mean and coefficient of variation were obtained. Resistance factors (?) for LRFD were then determined using Monte-Carlo simulations for each ultimate capacity criteria with the target reliability indices of 2.33 and 3.00.INTRODUCTIONThe Texas Department of Transportation (TxDOT) has used the Texas Cone Penetration (TCP) test since its development in the 1940s. The TCP test is an in-situ penetration test to characterize the materials encountered during geotechnical exploration. Texas currently maintains over 53,000 bridges in the National Bridge Inventory (FHWA 2016), and most of these bridges plus other transportation infrastructure in Texas are supported by foundations designed using the TCP test and its associated foundation design method. The Oklahoma DOT adopted the TCP test and foundation design approach in the 1970s, so the foundations for most of the 23,000 bridges in Oklahoma’s inventory were also designed using the TCP method. With this significant body of experience, the TCP method has been viewed as a straightforward, relatively easy-touse foundation design method that consistently yields safe, serviceable, economical, and maintainable foundations. TxDOT’s deep foundation design method is documented in the TxDOT Geotechnical Manual (TxDOT 2012) and currently employs the allowable stress design (ASD) approach. However, the Federal Highway Administration (FHWA) has mandated that the states begin to implement the LRFD method in place of the older ASD approach (Densmore 2000). This paper presents resistance factors at ultimate limit state (ULS) for design of driven piles using the TCP test, resulting from efforts to be in compliance with the FHWA policy."

Jan 1, 2017

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

When selecting a solution for improving resiliency at facilities, such as airports, utility and transit sites, there are many options to protect structures and equipment against potential flooding. Each case involves an evaluation of the several key factors such as: design flood parameters, the geography and geological conditions below the site, the facility, and the layout of buildings and equipment to be protected. Upon reviewing these conditions and conducting a cost analysis of various options, the most suitable approach to protecting a facility can be determined. This paper will compare the conditions at various New York City sites, and give detail to the solutions utilized at these sites to improve resiliency and protect each facility. Flood wall types varied as did the strategies for raising critical equipment, to meet the Federal Emergency Management Agency (FEMA) and American Society of Civil Engineers (ASCE) 7 guidelines. Due to granular soil conditions, some sites may experience soil seepage below the flood wall resulting in the need for underground cut off systems. The authors will also present detail regarding the solutions used to control seepage. Various cut off systems will be discussed such as grouting and sheeting, explaining the factors that may impact the choice of systems. Another consideration in flood resiliency is the potential for a buoyancy condition on basement slabs when localized flood barriers are employed on first floor doors and windows. The authors will discuss the potential impacts of this condition on facilities and methods to mitigate this issue. 1. INTRODUCTION New York City is an urban coastal Metropolis with varied geology and low land areas. This includes but is not limited to sandy soils at Coney Island and the John F. Kennedy Airport. Soft marshes are found near Flushing Queens and LaGuardia Airport. Heavy rains and coastal storms caused disruption to daily life and heavily affected the economy of this vibrant City. For instance, in lower Manhattan business was interrupted in the Financial District. Power outage was widespread; commuter trains and subways were stopped and put out of service. Additionally, numerous residential homes were damaged in Coastal Neighborhoods such as the Far Rockaways and Staten Island. 1.1. Superstorm Sandy Flood Statistics On October 29, 2012 Superstorm Sandy impacted numerous facilities in the New York City Metro area. The resulting damage cost New York City more than $42 billion in repair costs. $33 billion was allocated to repair housing and infrastructure, and $9 billion was allocated to protect transit systems1. One of the major issues that impacted the city in terms of its preparedness was the high flood surge. The surge surpassed the former base flood elevation and reached as high as 13.88 feet (above mean lower low water - MLLW) in Battery Park at 9:24pm that evening. Tottenville, Staten Island experienced more damage where the water was recorded at +16 (North America Vertical Datum of 1988 - NAVD88), which is equivalent to 18.7 feet above MLLW (see Fig. 1). Not only was the surge at record levels, the waves in New York Harbor were also at record level where some buoy stations recorded waves of up to 32.5 feet. The City released “A Stronger, More Resilient New York” in June 2013, a plan laid out to rebuild communities impacted by Sandy and improve the resiliency of the infrastructure and buildings in New York City. Figures below help to illustrate the extent of the inundation relative to the projects being discussed.

Jan 1, 2018

By G. R. Dasari

New Austrian Tunnelling Method (NATM) has been analysed by Finite Element method in two and three dimensions by Strain Dependant Modified Cam Clay (SDMCC) Model. The effects of construction sequence, stiffness of shotcrete and time dependency of shotcrete on surface settlement magnitude due to the NATM have been studied. Settlements obtained in 2D analysis, as expected, found to be more than the observations. The surface settlements obtained in 3D analysis found to be about 3 times less than equivalent plane strain analysis. This is due to mobilisation of soil strength around the tunnel face and soil-tunnel lining interaction. About 40% settlements occurred due to excavation of face at the monitor section and 60% after the excavation crossed monitor the section.

Jan 1, 1996

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1995

By Bolestaw A. Ktosihski

Preloading of bored pile bases by grouting is an effective way of reducing foundation costs. The bearing performance of a pile may be considerably improved. Various techniques and devices are used. Preloading of a pile base by a special grouting installation is preferred. The grouting device consisting of a U-shaped grouting tube with sleeves and a plastic membrane, separating the tube from the pile concrete, has well proven in Polish practice. The preloading may raise the pile design loads by as much as 30%, and increase their stiffness by 50%, in suitable conditions. The preloading equalizes the deformability of piles in a foundation or a structure. Examples of the base preloading use and load tests of base grouted piles are presented.

Jan 1, 2006