Search Documents

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By Deepak B. Deshpande

This paper enumerates various difficulties encountered in the design and construction of deep caisson foundations for the Second Bassein Creek Bridge constructed over a creek with very difficult site conditions. The designer of the bridge had anticipated the problems associated with the construction of large diameter floating caissons and limited the maximum size of caisson to 12.5m O.D. facilitated by the means of Shock Transmission Units (STUs). This is the first road bridge in India where STUs are installed to distribute seismic horizontal loads among piers installed with fixed and unidirectional bearings. Besides the usual difficulties of tilts, shifts, and sinking in the construction of floating caissons, the paper also describes a novel methodology used to retrieve a circular 12.5m O.D. caisson which had been swept away during a storm and stuck into the creek bed.

Jan 1, 2002

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By Robert A. Field

Static-Load Piledriving systems utilize hydraulic push to advance piles into the ground. Dynamic systems (ie. hammers and vibratory equipment) utilize impact, or vibration, to advance the piles. Static-Load systems are most commonly utilized in situations where noise or vibration would adversely affect the people, structures or equipment located near the site. Static-Load technology is most advantageous in situations where vibration, noise or access constraints make it difficult, risky or disruptive to utilize conventional piledriving systems.

Jan 1, 1995

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By Gregory A. Stephan

A case history of design, prediction, probe pile driving, and construction of a pile foundation for Building 3 of Waterside at Bay Beach Condominiums located in Fort Myers Beach, southwest Florida, is presented. Site geometry constraints, the presence of a 12.0 ft (3.6 m) deep lake occupying the southern one-third portion of the proposed building footprint, and marginal subsoils provided specific challenges for design and construction of the foundation. The subsoil conditions were explored by performing Standard Penetration Test (SPT) borings and a Piezocone Penetration Test (PCPT) Sounding to depths of 100 ft (30.5 m) within the building footprint. Additionally, borings were performed to envelope the building. Deep foundation alternatives included driven concrete, monotube, and steel pipe pile as well as drilled shaft. Following an evaluation of high structural loads, site-specific constraints, foundation test data from buildings 1 and 2, and preference expressed by the project owner, a pre-cast prestressed concrete (PPC) pile-supported foundation system was selected as an economical and effective foundation approach. Use of an augered cast-in-place (ACIP) pile foundation system was precluded by the project structural engineer. This paper deals with the design aspects and methodologies utilized in choosing and economizing the foundation system. The building foundation was designed for an allowable pile capacity of 40 tons (353 kN) in compression, 1.5 tons (12 kN) in lateral capacity for a deflection of 0.25-in (0.64 cm) and 15 tons (133 kN) in uplift capacity. For the single story extended garage structure, a pile capacity of 27 tons (238 kN) was indicated in compression. As part of the design process, an extensive probe pile driving program was carried out in order to evaluate the pile driving equipment, determine and verify pile capacities, and optimize the production pile lengths. A total of 33, 14-in (356 mm) square, PPC concrete piles were driven within the entire building limits, and dynamically load tested utilizing Pile Driving Analyzer (PDA) as part of the probe pile driving program. Utilization of PDA during probe pile driving helped in predicting pile set-up (i.e., increase in pile resistance with time) as well as reducing the pile lengths by as much as 20 percent. It resulted in variable pile lengths during the production phase. This information was effectively utilized as part of the overall quality control program to install a total of 559 PPC piles (including 33 probe piles) within the Building 3 footprint, including the reclaimed lake area, to depths ranging from 45 to 58 ft (14 to 18 m) below existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared reasonably well with the capacities from the CAPWAP analyses for probe piles. This engineered, monitored and tested foundation solution provided a cost effective and satisfactory basis for completion and approval of the foundation work for the building resulted in cost savings over other foundation alternatives for the owner. The building has since been occupied and a recent reconnaissance has indicated that the building foundations are performing satisfactorily.

Jan 1, 2003

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By Howard A. Perko

Soldier pile and lagging is a conventional means of temporary excavation shoring. Timber lagging design has traditionally been based upon the designer's experience or empirical rules. One such method is the Goldberg Zoino chart used by the Federal Highway Administration. Most of these methods restrict the designer to a consistent soil profile, certain pile spacing, construction grade timber lagging, and limited depth. The methods do not take into account surcharge loads or a variety of other factors that could arise. A designer working outside of ordinary circumstances with unusual loads, varying soil conditions, or alternate lagging materials has difficulty estimating lateral earth pressures. In rigid earth retention systems, lateral earth pressure is generally assumed to be constant along the length of the wall. In soldier pile and lagging systems, the lagging is often considerably less stiff than the steel soldier piles. As the lagging deflects, the soil tends to bridge between the stiffer elements resulting in a lower pressure on the lagging. Several previously published methods by others for determining this reduced pressure are summarized and discussed. These methods typically consist of using a portion of the active earth pressure in several different pressure distributions. A simple theoretical model is presented for determination of lateral earth pressures on wood lagging. The model is based on a three-dimensional "silo" shaped sliding wedge analysis. Results of the model are compared with other published methods. The model compares well with these methods which cover the normal spectrum of design situations. In addition, the model can be used to estimate lateral earth pressures outside typical situations.

Jan 1, 2008

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Frank Rausche

Since the early 1980s, when the Road Construction Authority of Victoria authorized the dynamic proof testing of roughly 100 drilled shafts of 1.5 m diameter and typically 60 m length in Melbourne Australia, dynamic load testing has been applied worldwide for quality control of drilled shafts. Today, test capacities of 4000 tons or more are not unusual. On numerous occasions the authors have been involved in similar tests in the United States and test engineers from other countries have reported on experiences in many different countries. Without doubt, generating high test loads is most economically accomplished by dynamic load testing and this method is particularly well suited for testing piles founded in rock because of the rocks low energy dissipation. However, deep foundation professionals have on occasion expressed reservations about subjecting a drilled shaft to impact loadings fearing, for example, a degradation of the shaft ? rock interface properties or potential error sources due to uncertain concrete properties or shaft geometry. This paper will present numerous case studies, demonstrating the performance of rock socketed drilled shafts under dynamic loads. It will discuss the mechanics of the dynamic tests and the method of data interpretation, addressing the concerns stated above and investigating the limitations of the test method. The paper will formulate a set of recommendations for the design and execution of these tests.

Jan 1, 2006

By Robert Thurner

The underground car park "Admonterhof in the historical centre of Graz is an example for the technical and economical success of a complicated structural design using a concept on the basis of the observational method. The intention to built a 20 m deep excavation beneath a protected monument was accompanied by some essential issues: the preservation of the existing state avoiding extensive displacements by means of a girder grid of reinforced concrete, its support on large bored piles and small steel-tube piles with possible active compensation of differential settlements, the excavation support in none built-up areas with secant bored piles, the underpinning of existing buildings with different structures by means of jet grouting. Furthermore the hydraulic gradient and the permeability of a rock formation in a part of the excavation had to be explored with the purpose to control the inflow of groundwater with a level difference of more than 10 m.

Jan 1, 2006

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009