Search Documents

By John P. Turner, Benjamin J. Turner

"This report describes a research project for evaluating the applicability of the widely accepted 80 percent criterion for elongation of ground anchors to anchors with unbonded lengths exceeding 100 feet. This issue is driven by several recent projects involving ground anchors for landslide stabilization in which a significant percentage of the anchors did not meet the criterion that requires measured elongation during proof load testing of at least 80 percent of the theoretical elastic elongation. The projects involved anchor unbonded lengths in the range of 85 to 220 feet, which is outside the range traditionally used in practice, although anchors of this length are being used more frequently for landslide stabilization. The principal objective of this research is to address whether the widely accepted criterion of 80 percent elongation is applicable for such applications, and whether other factors affect the ability of anchors to meet the criterion.Analytical methods for predicting transfer of load along the length of steel strand due to friction loss are used routinely in the prestressed concrete industry. These analytical expressions provide a rational framework for quantifying changes in load due to friction along the length of a ground anchor in terms of a ‘wobble coefficient’ (K) as defined in Aalami (2004). Values of the wobble coefficient for ground anchors can only be determined by back-calculating from load tests, i.e., fit the value of K to the appropriate analytical expression based on the known test load and measured percent elongation. The analytical basis is first developed and shown to provide a tool for evaluating results of anchor load tests to determine the magnitude of expected elongation as a function of unbonded length. Next, a database of anchor load tests is used to back-calculate values of K for anchors with unbonded lengths in the range typically used in geotechnical applications (< 100 feet). These values of K are then used to calculate expected friction loss for anchors with high unbonded lengths (100 to 250 feet) to evaluate whether the 80 percent criterion is reasonable."

Jan 1, 2017

By Federico Pagliacci, Claudio Asioli, Marco Chiarabelli

"""Rigid inclusions"" are a consolidation method that provides improvement of soft soils thanks to the installation of cylindrical columns made up of a material with significant and permanent cohesive properties, whose stiffness is 500÷5000 times greater than the surrounding natural soil’s. ""Rigid inclusions"" find their application in marginal areas (reclamations, polluted sites) to ensure stability of adjacent structures during construction of new buildings and to reduce the impact of natural disasters (liquefaction in the event of earthquakes, embankment collapse in the event of floods). This paper analyses the “rigid inclusion” construction method, related materials and equipment. Moreover, two performed projects will be illustrated. The first is the restoration of Lungarno Torrigiani Embankment in Florence, Italy. In May 2016, the Torrigiani embankment underwent a structural collapse causing a 3 m. displacement of the riverbank towards the Arno River. “Rigid inclusions” (with 300 mm diameter) have been used to re-compact the loose soil and create a stable working platform for the equipment. The second project illustrates the use of “rigid inclusions” (800 mm diameter and maximum depth of 36.6 m) to control the settlement of a new automatic cold store (30 m high with a 65 x 120 m foot print) for fresh frozen vegetables.RIGID INCLUSIONSIn general, the word ""inclusions"" means a type of consolidation that improves the strength of a soil mass through the inclusion of elements constituted by a material having better characteristics than those of the surrounding natural ground, to improve the overall mechanical characteristics of the treated soil. Inclusions are ""rigid"" when the material introduced into the ground has significant and permanent cohesive properties (concrete or cement mortar) and a significantly higher stiffness (500 ÷ 5000 times) than that of the surrounding natural ground.Typically, medium-small diameters (from 300 to 800mm) with low percentages of treatment (from 2% to 10% of the volume of soil) are employed, ensuring a high quality and consistency of the obtained product, both in terms of diameters and elastic modulus.According to the scope of the project and in urban areas, ""rigid inclusion"" columns can also be performed by means of small diameter drilling rigs (micropiles), weighing less than 20-25 tonnes."

Jan 1, 2017

By Kenneth E. Henn, David B. Paul, John D. Rice, Brian H. Greene

"Several laboratory modeling programs have been conducted to investigate the mechanisms associated with internal erosion of dam embankments and foundations. The investigation consists of developing laboratory devices to model three separate mechanisms associated with process: 1) contact erosion along bedrock joints, and 2) piping into an open bedrock defect. The contact erosion device subjects the soil above a bedrock joint to high velocity flows in the joint. The erosion into a bedrock defect device examines a number of static and transient hydraulic conditions to study the mechanisms associated with this type of erosion. Numerous tests have been conducted using both devices. The results of the modeling will be discussed along with a discussion of how this information could be used in future dam design and risk assessment studies.IntroductionA series of laboratory modeling programs were performed to assess the seepage and internal erosion behavior of several man-made and natural structures within dams and their foundations. Each model was performed on a “bench scale” and depicted an isolated location where internal erosion was likely to occur. The models were subjected to hydraulic boundary conditions to simulate the in-situ conditions so that the processes of internal erosion could be observed. Two laboratory devices were developed to model conditions depicting 1) contact erosion along a bedrock joint in contact with a dam embankment, and 2) backward erosion (piping) into an open bedrock defect (joint, solution void, etc.).Embankment dams often have rock foundations containing defects which may detrimentally impact future performance. Further, there are existing foundations which contain rock defects that may already be detrimentally impacting the dams; however, due to the inherent aspects of the mechanism, the signs of distress may not have propagated to the surface and thus not observed during inspections. A better understanding of the mechanisms which are influenced by, and impose their influence upon, rock defects will enhance the ability of dam safety professionals to analyze the risks associated with internal erosion due to rock defects, increase our ability to monitor and successfully initiate earlier detection, and also increase our ability to design remediation methods to contend with rock defect failure modes."

Jan 1, 2016

By Anthony T. C. Goh

"For deep excavations in soft clay, it is common to use jet grouting piles (JGP) prior to excavation to minimize wall deflections and ground settlement, and to prevent basal heave instability. In this paper, finite element analyses were carried out to assess the basal heave factor of safety for excavations in soft clay supported by JGP. Comparison of the factor of safety from the finite element analyses with limit equilibrium methods was then performed. Subsequently, to account for the uncertainties in the soil and JGP properties, a simplified reliability analysis procedure is proposed to estimate the probability of basal heave failure for deep excavations supported by JGP.INTRODUCTIONJet grout piles (JGP) are often used to prevent basal heave instability and to minimize excessive wall and ground movements associated with deep excavations in soft clay deposits (Shirlaw 2003; Wen 2005; Ou 2006). The jet grouting process which is carried out prior to any excavation works produces a series of short overlapping grout columns resulting in a “continuous” base slab (commonly termed as jet grout pile or JGP) below the final excavation level that spans across the entire excavation (Gaba 1990; Hsieh et al. 2003; Ho and Hu 2006). Typically, the JGP thickness ranges from 2 m to 4 m.The focus of this paper is on the assessment of basal heave instability for deep excavations in clay stabilized with JGP. Finite element analyses were first conducted to determine the basal heave factor of safety for deep excavations in clay with JGP. Comparisons were then carried out with factors of safety based on conventional limit equilibrium methods. Since the conventional factor of safety approach does not explicitly reflect the uncertainties of the soil and JGP properties, it is demonstrated in this paper that a simple reliability based approach (Hasofer and Lind 1974) can be used to assess the probability of basal heave failure.LIMIT EQUILIBRIUM METHODFor excavations is clay, the Terzaghi (1943), Bjerrum and Eide (1956) and Eide et al. (1972) methods which are based on bearing capacity theory, are commonly used to determine the basal heave factor of safety. Another commonly adopted method in Japan and Taiwan is the slip circle method which involves taking moments about the lowest strut level (JSA 1988; Hsieh et al. 2008; Luo et al. 2012). The slip circle method has also been applied for excavations with a JGP at the base by incorporating the undrained shear strength of the JGP. In the slip circle method, the basal heave factor of safety FSslip is assessed by taking moments about the lowest strut level (Fig. 1)"

Jan 1, 1900

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By Gerald Verbeek, Erick Baziw

Dynamic soil analysis (DSA) in geotechnical practice is intimately related to the capability of measuring the necessary soil properties of shear modulus and absorption. In DSA the methods of analysis are based upon the stress-deformation response of soils due to imposed shear strains. Typically the soil profile is numerically modeled as linear visco-elastic system. This technique is referred to as the Equivalent Linear (EL) method, and it requires the specification of the input parameters of low-strain (<10-5) shear modulus, modulus reduction, and the equivalent viscous damping ratio, which is directly related to the soil absorption value. Downhole seismic testing (DST) has proven to be a very accurate tool for estimating low strain shear modulus values as long as source wave raypaths are taken into account, especially for near-surface investigations. DST has also been utilized to estimate low-strain interval absorption values. In these cases standard frequency domain absorption estimation algorithms (such as the spectral ratio technique) are utilized where it is assumed that the source waves are traveling along the same travel path, which is obviously not the case for near surface DST investigations. This paper outlines a unique DST absorption estimation methodology, which is carried out in the time domain and takes into account source wave travel paths. 1. INTRODUCTION There is considerable interest in methods of geotechnical in-situ engineering that provide accurate estimates of the shear wave velocity and the associated absorption values in the ground, since these parameters form the core of mathematical theorems to describe the elasticity/plasticity of soils and they are used to predict the soil response (settlement, liquefaction or failure) to imposed loads (whether from foundations, heavy equipment, earthquakes or explosions).

Jan 1, 2019

By Michael W. Neill, O&apos

This presentation addresses some of the problems encountered in estimating the capacity of drilled shafts and augered, cast-in-place piles in soft rock. Methods to quantify side and base resistance are suggested. However, the methods that are described should always be verified locally by performing load tests.

Jan 1, 2001

By Michael Shedlosky, Sonia Sorabella Swift, Nina Carney, David Tarasovic

Rigid inclusions were used to support roadway fills and mechanically stabilized earth (MSE) walls for the South Capitol Street Corridor project. The first phase of this two-phase, nearly $1 billion project will include the replacement of the Frederick Douglass Memorial Bridge, including two approach ovals east and west of the Anacostia River, the replacement of the I-295/Suitland Parkway Interchange, and the construction of several traffic ramps. The bridge itself carries over 70,000 drivers daily and is expected to open in 2021. Ground improvement is required over a portion of the project footprint. Within the ground improvement area, the construction includes MSE walls up to 35 feet high and embankment fills up to 28 feet for which CMC rigid inclusions (RIs) were used to mitigate settlement and stability. The proposed construction runs over multiple old, in-service utilities that the project requirements indicate could not tolerate any stress or settlement due to the construction. As such, solutions that spanned the utilities were required. A concrete slab of varying thickness was used to span a fragile 108-inch-diameter sewer pipeline and 48- inch-square-precast-concrete box beams were used to span twin utilities that were buried just a few feet below current working grades on site. Unreinforced RIs were used to support these structures. The center to center spacing of the RIs perpendicular to the pipe run was 26.5 ft for the concrete slab and 62 feet for the precast--concrete box beams. The axial forces on the RIs were up to 267 kips. The RIs were not structurally connected to the slab or box beams. A single-element load test was performed to confirm the load-carrying capacity of the RIs. This paper will focus on the utility protection slab over the twin utilities and provide an overview of the design of the structural and geotechnical solutions and will present the results of the load test performed. INTRODUCTION The new Frederick Douglass Memorial Bridge (FDM Bridge) and reconstruction of the Suitland Parkway/ I-295 interchange (South Capitol Project) is a part of the Anacostia Waterfront Initiative (AWI) Program, whose goal is to transform the shores of the Anacostia River. The existing FDM Bridge is approximately 70-years old and has been classified as “functionally obsolete”. The completed South Capitol Project will improve the multi-modal transportation options, increase pedestrian and vehicular safety and provide additional green space. The proposed FDM Bridge, a rendering of which is shown in Fig. 1, is designed to become a landmark bridge in the Washington, D.C. area.

Jan 1, 2019

By Abid Adekunte

"Engineers and developers have witnessed the growing popularity of deep basement structures as components of urban commercial and residential developments. This is often attributed to inadequate surface parking facilities in urban centres and a somewhat popular belief that underground parking facilities improve both commercial and aesthetic values of urban structures. For many years, diaphragm walls and sheet pile walls have been widely accepted as effective deep excavation support systems for basement construction in urbanised zones. However, these are now being replaced by bored pile retaining walls as preferred earth retention systems of choice on many projects for several reasons, which may include economy, faster installation process, reduced space requirement for machinery and ancillary equipment, flexural rigidity and axial capacities.However, there are complexities associated with the use of bored pile retaining walls on urban developments. These include; limitations due to vertical and horizontal installation tolerances, which is a major issue when wall is required to provide groundwater cut-off for multi-level basements as tolerances are difficult to achieve for deep piles, uncertainty associated with the prediction of wall axial capacity as piles are rarely tested, difficulties in using temporary props as wall restraint due to restricted working spaces in urbanised zones and difficulties in adopting ground anchors as restraint due to the existence of adjacent sensitive structures in built-up areas. Such complexities have resulted in cases of failure, non-serviceability and abandonment of basement construction schemes. Therefore, overcoming the intricacies associated with the application of bored pile walls is becoming a priority to the present day basement engineer.This paper is centred on the numerical modelling, design, construction and monitoring aspects of four recent case histories of multi-level basement and marine engineering construction schemes in the United Kingdom and the Republic of Ireland, which involved the use of bored pile retaining walls. The paper highlights the various customised approaches and innovative novel solutions adopted on the sites, to mitigate risks and ultimately overcome the intricacies associated with the earth retention techniques. Simple empirical equations for developing the geometry of secant pile walls for effective groundwater cut-off are presented and validated. An alternative approach for predicting axial capacities of bored pile walls is also presented; this is shown to be considerably less conservative than a common routine design approach, while also in good agreement with observations made in a recent series of laboratory-based scale model tests."

Jan 1, 2017

By Richard Brink, Eric M. Klein, Kenneth B. Andromalos

"A portion of the roof for a 129 x 144-inch, nearly 100-year-old sewer outfall in the City of Baltimore had deteriorated to the point that it resulted in the development of a large sinkhole in a residential neighborhood. A subsequent video inspection of the sewer outfall indicated that there was a hole in the sewer outfall, and it would need to be repaired . After initial backfilling of the sinkhole and repairs to the water service lines, a conventional wood shoring system was used to support the excavation and expose the Main Outfall Sewer to inspect and repair it. This excavation was unsuccessful because of loose sandy soils and high groundwater conditions. An innovative use of a steel reinforced jet grout excavation support system was ultimately used to underpin an adjacent 20-inch water main and other nearby utilities, and provide access to the top of the Main Outfall Sewer some 22 feet below the street surface to facilitate inspection and repair of the sewer. This excavation support system was also successfully utilized in the final repair of the sewer roof by serving as a buttress for the new roof system.1.0 IntroductionThe project site is located in a residential neighborhood with brick masonry row houses situated on the south side of Chase Street and a brick masonry church on the north side of the street. Figure 1 illustrates the location of the site. The City right of way is 65 feet wide, and the street is 40 feet curb to curb. The centerline of the Main Outfall Sewer runs parallel to and a few feet south from the centerline of the street. Other utilities running parallel to the street include a cast iron 20-inch water line built about 1910, a 24-inch terra cotta storm drain, a 6-inch terra cotta sanitary sewer, a 4-inch cast iron gas line and a 40-inch electrical duct. Cross utilities included a 4-inch gas line and several smaller water and gas service lines to the church and row houses. One gas line that was not shown in the City's GIS database was exposed during the excavation."

Jan 1, 2005

By Peter Yen

This session consists of five papers. Three involved research on the properties of grout materials, specifically ultrafine cements and polyurethane grouts. Two papers present the development of soil grouting technology and monitoring methods. Of great interest are the papers on ultrafine grout penetrability testing focusing on the pressure filtration effects encountered in permeation grouting applications (Ericksson, Stille and Mittag, Savidis). The comparison testing of hydrophilic and hydrophobic polyurethane grouts submitted by Vrignaud, Ballivy, Perret and Fernagu assessed the long-term performance of these materials for repairing saturated cracks in concrete, subject to thermal expansion and contraction. Two very practical papers present the development of soil grouting, where permeation, fracture, replacement, jetting and other grouting techniques are utilized. The papers by Lees with Chuaqui and Warner present experience with ultrafine and other commonly used grout materials. Methods to measure and monitor the injection process and verify production progress are discussed.

Feb 10, 2003

By Sherrill Gardner

Vibratory drivers have been used since the 1930s to drive and extract piles. Vibratory pile drivers have the capability of significantly decreasing pile installation time, especially in granular type soils. However, they have not been widely accepted because of the uncertainty in estimating the bearing capacity of the driven pile. When driving bearing piles, the industry standard method for obtaining load carrying capacity of a pile installed with a vibratory driver is to redrive with an impact hammer. The advantage of improved productivity is lost with the redrive procedure. Currently, there is no other method to predict the capacity of these bearing piles installed with a vibratory driver. The Naval Civil Engineering Laboratory (NCEL) is making progress towards being able to estimate the bearing capacity of these piles. This paper describes field testing and corresponding analytical modeling of the vibratory driver-pile-soil system. The following sections describe the development of the numerical model and techniques for collecting field data. A discussion of the prediction of the pile driving process based on field test data is followed by suggestions as to the additional work that should be done to further verify the model to a point where it can be used with confidence.

Jan 1, 1987

By Justin Simmons, Michael Arnold, Bob Faulhaber

"In order to remodel an existing beach resort on the Gulf of Mexico, an existing three story structure, founded on stepped tapered piles, was to be replaced by a ten-story building with service rooms on a daylight basement level, conference rooms on the next levels and up-scale hotel rooms on the upper levels. The new building was founded on augered-cast-in-place (ACIP) piles. The pile caps and the basement required excavations between nine and fifteen feet (three to five meters) below ground surface.BAUER Foundations Corp. (BFC) successfully used Cutter Soil Mixing (CSM) to install the support of excavation walls. This technique allowed for the adjustment of the wall alignment during execution in order to avoid existing and new piles and other underground obstructions. Nearly 1600 – 16-inch (400 mm diameter) ACIP piles were installed to an average depth of 71.5 feet (22m) below ground surface (BGS) by BFC to support the new hotel structure. Initial grout overages in piles were excessively high and ground stability issues were encountered in some pile locations. By identifying specific areas of concern BFC was able to modify the approach to ACIP installation, effectively mitigating the ongoing risks and successfully completed the project.PROJECTMarriott Hotels began the $300 million renovation and upgrade of their Marco Island Marriott Beach Club Hotel in Marco Island, FL to JW Marriott status in May 2015. The renovation included the demolition of a portion of their existing hotel tower, and the construction of a new 10-story hotel tower consisting of 94 new guest rooms and a 10,000 SF (900 m2) ballroom, among other amenities. As is typical with hotel construction, time was of the essence. The schedule was the driving factor of this project as the owner had already booked events in their new ballroom starting in January of 2017.BFC provided the client with a deep foundation package that included the installation of 1562 Augered Cast-In-Place (ACIP) piles supporting the new tower, and the design and construction of approximately 36,500 SF (3,400 m2) of soil-mixed retaining wall for support of excavation (SoE)."

Jan 1, 2017

By Marco D. Boscardin, Kenneth A. Pidgeon, Adriane G. Boscardin

"Hollow bar tiebacks can offer an economical alternative to conventional solid bar and strand tieback systems for use in temporary excavation support construction. However, the limitations associated with the installation of hollow bar tiebacks require special attention during design, construction and load testing to verify conformance with conventional performance and proof testing criteria (PTI, 2014). In particular, providing a reliable free length is complicated by the 10-foot (3-m) -long, segmental, couplingto- coupling nature of the free length sheath in the hollow bar system, and addressing the fully grouted annulus of the bond zone and the free length zone at the end of installation are key concerns. In addition, it is often more convenient to install a greater number of more closely spaced, lower capacity tiebacks with the hollow bar system, compared to conventional tiebacks. This paper examines how these issues were addressed for a project involving a 60-foot (18-m) -deep sheet pile excavation through a highway embankment and a 70-foot-deep sheet pile and soldier pile and lagging excavation through a railroad embankment, both supported by a hybrid system of hollow bar tiebacks and hollow bar soil nails. The project involved approximately 300 tiebacks and 400 soil nails.INTRODUCTIONEngineers Construction, Inc. (ECI), constructed a pair of 32-foot (9.8-m) -wide (clear span), 30-foot (9- m) -high (21 feet (6.4 m) above the stream bed), cast-in-place concrete arch culverts as a design-build project for the Vermont Agency of Transportation (VTrans) in East Ryegate, Vermont. The new culverts replaced an existing 8-foot (2.4-m) -wide by 6-foot (1.8-m) -high cast-in-place concrete culvert under US Route 5 (RTE5), and twin, 2-foot (0.6-m) -wide by 5-foot (1.5-m) -high granite block culverts under the Washington County Railroad (WACR) alignment. The culverts convey Manchester Brook eastward, through the embankments for RTE5 and the WACR, on its way to the Connecticut River. The Connecticut River is located approximately 100 feet (30 m) east of the WACR embankment. The existing structures were undersized and backed up water behind the embankments during high flow events; and often trapped debris that flowed down the brook and became clogged. The existing culverts also had cracks and openings that have resulted in the loss of ground into the culverts and the formation of sinkholes in the sides of the embankments. Moreover, the reason for the large cross-sectional dimensions of the culverts was to make them of sufficient size and openness to encourage the migration of fish up the stream to spawn. The culvert through the RTE5 embankment is 144 feet (44 m) long, and the culvert through the WACR embankment is 128 feet (39 m) long, with a 57-foot (17.4-m) -long by 32–foot (9.8- m) -wide by 17-foot (5.2-m) -deep 10 feet (3 m) deep above the stream bed) open channel section between the two culverts. A plan view of the culvert alignment is presented in Figure 1."

Jan 1, 2016

By William B. Conway

This paper will describe the large caisson pier foundations for four of the bridges crossing the Mississippi River in the New Orleans area; and will discuss some of the unusual problems encountered during their sinking. Certain settlement phenomena experienced during their service life will also be related: The four bridges in order of their construction: The Huey P. Long Bridge, River Mile 106.1, completed in 1935 The Greater New Orleans Bridge No.1, River Mile 96.0, completed in 1958 The Hale Boggs Bridge, River Mile 121.6, completed in 1983 The Greater New Orleans Bridge No.2, River Mile 96.1, completed in 1988 Each of these bridges employed large open-dredged concrete caissons as foundations for one or more of the river piers, with the smallest being the 65ft by 102ft caissons for Piers I and II of the Huey P. Long Bridge and the largest being the 99ft by 214ft caisson for Pier II of the Greater New Orleans Bridge No.2. The Huey P. Long caissons are founded in a dense fine sand at -170 while all of the other bridge caissons are founded in hard preconsolidated clay at elevations varying from -150 to -185. The Huey P. Long Bridge is currently being widened without increasing the caisson foundations under any of the river piers; and the design reasoning that led to this decision is presented.

May 11, 2007

By Moritz Schleeh, Christian Moormann

Temporary working platforms are generally required in order to ensure that heavy construction machinery such as drilling and trench wall units, pile drivers, vehicle and crawler cranes can be set up safely at the site of operation. Considering all possible operating and loading conditions, especially on ground of low shear strength and stiffness, the design and construction of temporary mobile working platforms needs to be considered more as a serious engineering task than as a second order structure of minor relevance. Working platforms reinforced with one or several geosynthetic layers have proven to be especially effective with regard to stability, serviceability and durability but their design requests even more sophisticated approaches. Existing design models are often based on simplified assumptions and do not consider the complex interaction between construction machinery, working platform and subgrade. Non-monotonic loading as well as elastoplastic and time-variant deformation of cohesive subsoil can adversely affect the base layer system and the serviceability and stability of the construction machinery operating on it. In this context, there is a need for improvement of design approaches and their optimisation considering that there are no generally accepted design approaches or technical codes of practice available for the design of temporary working platforms. The present paper deals with the multifaceted and non-trivial interaction effects of working platforms investigated by model tests, field measurements and numerical simulations to develop a design approach that ensures a safe installation and operation of heavy plants on unstable ground.

May 1, 2022

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which -are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-In-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

May 11, 2007

By Onur Guvener, Kalaiarasi Vembu, C. Vipulanandan

"Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.INTRODUCTIONAugered cast-in-place piles (ACIP) are drilled foundation installed by drilling a hole with a continuous flight auger to a predetermined depth. Non-displacement Augered Cast-in-Place (ACIP) piles are increasingly used for supporting building, bridges, sound barrier walls and many other structures around the world. In an ACIP pile, depending on the soil type and rate of the auger advance, ground stresses are maintained near the value that existed before construction by using a continuous flight auger, which is never withdrawn until the cementitious material (fluid Portland cement grout) is placed by pumping the grout beneath the withdrawing auger under pressure through the hollow stem of the auger (Vipulanandan, 2005). ACIP piles are typically installed with diameters ranging from 0.3 to 1.0 m and lengths up to 30 m (Brown, 2005) although longer lengths have occasionally been installed. Comparing to the drilled shafts and driven piles of equivalent size ACIP piles can be installed more rapidly with fewer disturbances to the surroundings in favorable geological conditions. Hence the installation procedure and the quality of material used in the construction have significant effects on the behavior of ACIP piles (Vipulanandan, et al. 2007). In this paper construction quality control technique for ACIP piles was investigated. Load displacement and load transfer behavior of pile in compression and tension in hard clay was also studied. The development of side resistance in compression and tension for the load test piles and the reaction pile were also investigated."

Jan 1, 2017

By Slav Tchepak

The King&apos;s Wharf development is located in Sydney&apos;s Darling Harbour area. The site was originally used for industrial maritime purposes, which over the years has been reduced to accommodating leisure craft only. The site has been filled with various materials, resulting in fill materials varying from soils, to concrete and rock fill. A prestigious new residential development at the site required piles to found in Sydney sandstone that occurred at depths ranging from 1 to 27m. The selection of appropriate pile types is discussed, as are details relating to the design and construction of cast insitu Omega piles and CFA piles. A number of issues needed to be addressed relating to the piling, including the design of the piles, the potential for liquefaction of the fill material due to earthquakes, penetration of the piles through the fill materials, installation of the piles to a satisfactory positional tolerance and pile performance. A number of piles were dynamically tested to prove pile performance and these results are presented and compared with design expectations. The project was successfully completed on time and budget, indicating the selection of pile types in the difficult ground conditions to be appropriate.

Jan 1, 2000