Search Documents

By Eric P. Bregman

As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800?s where busy commercial streets co-mingle with thickly settled residential houses. The subsurface conditions present within Boston?s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations. This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area.

By Eric P. Bregman, Franklin M. Grynkewicz, John E. Regan

"As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800’s where busy commercial streets co-mingle with thickly settled residential houses.The subsurface conditions present within Boston’s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations.This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area."

Jan 1, 2017

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By Ramanathan C, Prasad P. V. S. R

The most critical challenge for any large size storage structures to be constructed on soft compressible soils is bearing capacity and consolidation settlements. Consolidation is the time dependent phenomena, as expulsion of water from soil voids on application of external load will take longer period. It is mainly influenced by soil consistency, permeability, thickness of compressible stratum and presence of free draining layers. This study deals with the foundation solution of a large size Mounded Storage Vessel (MSV) to be constructed on thick compressible stratum whose loading intensity is around 155 kPa and the estimated settlements are greater than 400 mm. Hence, the foundation solution using vibro stone columns is adopted as an effective technique to address the challenges of excess settlements and inadequate bearing capacity. Further to keep settlements within the permissible limit of 50 mm, preloading technique with 60% of actual loading intensity will be utilized. The consolidation analysis of stone column reinforced foundations is carried based on the method given by Han and Ye (2001). The quality of the stone columns is ensured by real time quality control measures and the performance of the stone columns shall be ensured by vertical load tests. Ground settlements was closely monitored with proper instrumentations and the actual degree of consolidation has been verified by Asaoka’s (1978) method.

Sep 1, 2022

By Robert L. Goehring, Fred Munene

This case history for three major additions to a tire manufacturing plant in north Georgia discusses the impact of highly variable Karst (sinkhole) geology on both foundation design and construction. For Phase 3, alternatives were considered for a heavily loaded mixing tower with up to 2,000 kip column loads. A non-traditional approach of using auger cast piles was adopted. To satisfy a risk-averse Owner, a pile load testing program including strain gauges was conducted. One test pile was cored full depth to demonstrate effective bearing on steeply inclined rock. For Phase 4, similar methodology was used at another critical mixing tower structure associated with that phase and the installation procedure was refined to reduce grout take. In Phase 5 construction, another mixing tower and the equipment pits were supported on auger cast piles. After pile installation, a sinkhole opened up between two equipment pits. Remedial grouting was performed. Development also required construction of a R&D building over a 96 inch diameter RCP storm sewer. Auger cast piles were used to support the building to avoid overstressing the existing pipe and risk separating joints. This case history outlines lessons learned while constructing auger cast piles in Karst and proving quality was built into the foundations.

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Thomas J. Kennedy, Michael D. Bennett

The study of geotechnical history is well-established. Most geotechnical practitioners, teachers, and graduate students have some grasp of the origins of the field. However, this understanding often consists of a jumble of names and anecdotes. This paper discusses how a deeper comprehension of geotechnical history can benefit academia and practice alike and describes how the authors have begun a wide-ranging study of the subject. The paper reviews the dual-track methodology the authors have generated for the study, which consists of written articles about different works in geotechnical history and a database tracking how often pieces have been cited in geotechnical literature. The first technique has shed light on aspects of geotechnical history such as the connection of the Darwin family to the origins of geotechnical engineering, the St. Francis Dam failure of 1928, and the rivalry between theoreticians and practitioners in the early days of the field. The second has helped quantify subjects such as the outstanding contributions of Karl Terzaghi, the disagreements between Terzaghi and Donald Taylor, and the specialization of the field over time. The paper concludes by discussing the authors’ planned future work on geotechnical history.

Oct 1, 2022

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Silas C. Nichols, Jennifer E. Nicks

"Limit states design (LSD), or load and resistance factor design (LRFD), is a method to account for the uncertainty in loads and resistance through a reliability calibration that requires all applicable limit states (strength, service and extreme) to be checked during foundation design. LRFD has been in use internationally for several decades; however it wasn’t until recently that engineers working on highway projects were required to use the method for the design of highway bridges and other appurtenances. Although the bridge community has been using a form of limit states design for structural components since the early 1970s, the design of foundations for bridges, walls and other geotechnical features had long been performed using allowable stress design (ASD), whereby all uncertainty in loads and material resistance is combined in a single factor of safety. While the move to LRFD was viewed as a more rational approach for the design of bridges and structures, the transition to its use for geotechnical engineering has been met by many with confusion and difficulties in application. This article will revisit the history of transition from ASD to LRFD for geotechnical engineering, summarize the status of the transition and issues with its use, and briefly discuss some emerging research opportunities for improving and advancing the design platform.Background and HistoryUntil about a decade ago, foundations and substructures for bridges were traditionally designed using ASD, while the superstructure was designed using load factor design (LFD), a precursor to LRFD that incorporated factored design loads but no risk assessment. This combination led to uncertain and incompatible safety margins in design for the various bridge components. In 1986, the American Association of State Highway Transportation Officials (AASHTO) Subcommittee on Bridges and Structures (SCOBS) concluded that the standard bridge specifications in use at the time for U.S. transportation projects had significant inconsistencies and gaps, wasn’t up to date with emerging technology and that the development of new specifications was warranted. The proposed solution by the subcommittee was to transition to a more coherent method of design where applicable failure and serviceability conditions could be evaluated considering the uncertainties associated with loads and resistance."

Jan 1, 2015

By Nabil F. Ismael, Khalid Farraj

"The axial load transfer along large diameter bored piles in very dense silty sand was examined by field tests. Two instrumented piles 1.2 m diameter and with embedded length of 18 m and 25 m were load tested in axial compression to failure in connection with the construction of a big tower building in Kuwait City, Kuwait. Instrumentation included vibrating wire strain gages at various levels, displacement transducers and extensometers. The purpose being to measure the axial load distribution, skin friction, and base resistance at various load levels. In addition the settlement of the piles and the elastic compression were monitored. The ultimate pile capacity, side friction, and base resistance were determined and correlated with the Standard Penetration Resistance values as determined from the boreholes. Most of the load was transferred as side friction and the pile settlements at the maximum loads ranged from 1.6% to 2.2% of the pile diameter.INTRODUCTIONLarge diameter bored piles are used with increasing frequency for heavy structures in Kuwait and the Gulf region in calcareous sand. The behavior of short piles ranging in depth from 8 m to 15 m was examined by field test (Ismael 2012). However, larger diameter and deeper piles are being used more frequently, including the project described in this paper which included piles with 1.2 m diameter and 18 m to 25 m depth. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on long large diameter piles installed through very dense sands or silty sands are very limited at present. The results of two load tests carried out recently on instrumented bored piles at one site in downtown Kuwait City have become available. In these tests the failure load was extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers."

Jan 1, 2017

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

"Premissas BásicasCaracterísticas do concreto centrifugado(Spun concrete characteristics)Aplicação em obras de engenharia de fundações(Application engineering works foundations)Logística de fabricação e transporte(Manufacturing logistics and transportation)Emendas x uso de aplicação(Amendments x use application)Geologia brasileira, da região costeira a presença de grandes bolsões de argila mole(Brazilian geology, coastal region the presence of large pockets of soft clay)Influencia do sistema de cravação(Influence of driving system)Transferência da Energia Aplicada(Applied Energy Transfer)Estacas longas(long piles)Controles executivos (diagrama de golpes, nega, repique elástico, ensaios de carregamentodinâmico, provas de carga).(Executive Controls (blows diagram, sets, elastic rebound, dynamic load tests, load tests).)ECD – aplicação da metodologia do DIETECD - application of the methodology DIETBrazil has a highly variable geology all along its coast that directly influence the choose of foundation type, being too employed the use of reinforced spun concrete piles initially ranged in diameter from 60 to 80 cm. Over the past 10 years with the advent of investment in marine works projects began to demand a new range of piles with diameters greater than 100 cm and in the absence of amendments.On land is also very remarkable the presence of regions with large layers of soft clay, in prime areas that have been explored. A classic example is the Barra da Tijuca in Rio de Janeiro that has suffered from the housing boom growing toward these regions. In these regions it has been very common driven lengths of about 40.0 meters, which basically go through thick layers of soft material or unconsolidated and they will find strength in depth with residual soil layers or even the bedrock.The spun concrete has great qualities for application in deep cuttings resulting from the production process, which gives a redistribution of fresh concrete mass collaborating with the particle size distribution effective loss of water that is thrown to the center stake being subsequently discarded. Consequently this contributes to a reduction in the factor a/c that is directly connected to increase strength.The fact that there is a sort of concrete helps to reduce voids in the mixture, which increases the durability characteristics. This condition made it possible to employ the spin technique on poles, which are directly linked to aggressive media in large urban centers.Another very attractive feature is that the centrifuge process can work with concrete with the lowest percentage of mortar and more gravel. This concrete mix directly contributes to increasing the specific modulus of elasticity, thus allowing a greater capacity to absorb the energy of the blows transferred with less deformation.Despite the great potential of land application of prefabricated spun concrete stakes there are only three factories and its limitation is the cost of transporting manufactured for the various regions, since all transportation is done by road.For its transportation is carried out exclusively by trucks, this limits the size of cuttings being produced commonly in length from 11.0 to 12.0 meters in length and smaller compositions. For use in long piles of works is resorted to amendments in the form of metal rings, concreted near the ends of the stakes, with the transfer through steel bars in CA-50 welded to the ring. Usually run in steel ASTM A-36. Later in the work these rings are welded with coated electrode.In the case of maritime stakes are very used to drowned splicing technique, which basically consists during the spin process leave one end with the armor of the apparent stake and work together two elements and make specific, with superior resistance to the prefabricated stake.This study in addition to briefly introduce the process of manufacturing, design and logistics presents a detailed study of applicat"

Jan 1, 2015

By Chandramohan P. V., Ravi Kishore

"An underground reservoir was to be constructed at Doha in Qatar. Simsima lime stone is present at the bottom. When the reservoir is empty, there will be uplift at the bottom but this will change to downward load when it is full. The rock at the bottom had high bearing capacity to resist downward load. But uplift had to be resisted by piles or anchors. The reservoir has a size of 120mx80m. Shrinkage and creep of concrete coupled with thermal contraction imposed a horizontal movement of 26mm on the extreme piles. So, piles have to accommodate this as well. This unique situation needed a unique solution. The solution was to provide piles with flexible high tensile strands to take tension. An annular space near the head of the pile would facilitate horizontal movement as well. Compression load was directly passed on to the raft bearing on rock.INTRODUCTIONAn underground reservoir for storage of drinking water was to be constructed at Doha, Qatar. The reservoir was proposed to have a plan size of 120m x 80m. Clear height inside the reservoir was proposed as 17.2m, from the bottom of roof to the top of bottom raft. Overall height of the reservoir at the outlet from the top of the roof to the bottom of raft was to be 21.2m. For the sake of inspection and in order to prevent pollution from the surroundings a gallery was planned around the reservoir. This could accommodate pipelines as well. This gallery was 3.0m wide on three sides and 8.4m wide on the outlet side.The gallery had removable gratings as cover in order to facilitate maintenance. Capacity of the reservoirwas proposed to be 40million gallons. The reservoir is divided into four compartments with baffle walls in each one for water circulation. Roof of the reservoir is kept at 300mm above ground level. There are two levels of car park on top of the reservoir. Top of the reservoir roof is at +14.35. Bottom varies from - 6.68 to -7.08. Lowest water table is at +6.00. Concrete structure of the reservoir was designed by a local consultant. The Navayuga Engineering Company was entrusted with the construction. Please see Figs 1 and 2."

Jan 1, 2017

By Ali Nasirian Ph. D., Gabriel Carvajal

To facilitate the safer and more secure transportation of inmates from San Diego Central Jail to the new San Diego Courthouse, the County of San Diego committed to building a new transfer facility as part of the downtown developments. The transfer facility includes a three-story underground structure adjacent and connected to the Central Jail and a 60-ft deep, 23-ft diameter, 320-ft long tunnel. The tunnel starts at County Jail, passes underneath Western Regional Detention Facility (Old Jail) and, ultimately, connects to the State Courthouse. Condon-Johnson & Associates, Inc. (CJA) was selected to install the temporary shoring shaft for the underground structure as well as three arrays of canopy pipes to support the tunnel’s Sequential Excavation Method (SEM) construction. CJA installed the rectangular 56-ft deep access shaft shoring with three levels of bracing, and a combination of secant piles, soldier piles, and timber lagging. The shoring also included a sliding bridge at top to provide access for trucks to enter and exit from county jail during the duration of construction. Following shoring and shaft excavation, CJA installed and grouted 7-5/8” dia. canopy pipes in 3 reaches, parallel to the longitudinal design line of tunnel with a slight lookout angle. CJA installed 24 each canopy pipes, 99-ft from face of shaft at reach 1, 21 each, 80-ft length canopy pipes at reach 2, and 21 each, 75-ft length pipes at reach 3. CJA confirmed canopy pipe alignment via Inertial Sensing Gyro. To mitigate the possibility of settlements caused by the tunneling operation underneath Old Jail strip footing and grade beams, CJA also performed void fill grouting. Sleeve port grout pipes (SPGP’s) were installed inside the Old Jail basement and grouted with the use of packers as the tunneling operation passed underneath the Old Jail. In detailing various aspects of the construction, this paper aims to magnify the innovative solutions for shoring, canopy pipe installation and void fill grouting challenges as well as the state of the art quality control measures undertaken by CJA.

Oct 1, 2022

By Ronald Damen, Dion Denes

"Friction fatigue is the loss of soil-pile friction around the shaft area of the pile. It has been observed during impact driving of piles, and has been modelled to a limited degree using physical scale models. This paper proposes the use of high strain dynamic pile testing to assess and quantify friction fatigue in impact driven piles. The method is applied to two case studies: one on a project off the north-west coast of Australia and one on a South Pacific Island. On both sites calcareous sand layers are present. Pile Driving Analyzer (PDA) monitoring has been conducted during impact driving of steel piles, which allowed for assessment of shaft resistance development both with depth and with progressive driving, by use of wave equation signal matching. Lessons are drawn from the case studies to improve future observations.INTRODUCTIONFriction fatigue is the loss of soil-pile friction around the shaft area of the pile, under cyclic loading or during pile driving. The phenomenon has been frequently observed in some non-silica sands, such as pumice sands and calcareous sands and has been the subject of academic study.The occurrence of friction fatigue impacts the driving behaviour of piles and the shaft friction component of the ultimate geotechnical strength (Rd,ug). If potential friction fatigue is not recognised in the design phase of a project, required pile toe levels can be significantly underestimated. This could lead to extra cost and delays, or, if no adequate pile verification is conducted, to geotechnical failure or underperformance of piles. This is especially true in remote locations, such as Pacific islands, where calcareous material is often present.A better understanding of the phenomenon would aid both pile design and driveability assessment. This paper proposes the use of high strain dynamic pile testing to assess and quantify the effect of friction fatigue from impact driving. Two case studies are presented in which high strain dynamic testing has been conducted on driven piles in calcareous sands to illustrate the method.BACKGROUNDFriction fatigueThe geotechnical strength of piles is composed of the resistance to static loading by the base of the pile and the shear resistance between the shaft of the pile and the adjacent soil. The latter is often referred to as the shaft resistance or shaft friction.During impact pile driving, a decrease in shaft resistance is often observed. Although this phenomenon is also observed during vibratory pile installation, this paper deals predominantly with impact driving. This decrease in material strength from the tip of the pile influences the shaft resistance and may be either temporary or permanent. Temporary reduction in shaft resistance is common in cohesive soils and is thought to be caused by excess pore water pressure, which has insufficient time to dissipate. This phenomenon, commonly referred to as set up, is observed to a significantly lesser extent in non-cohesive materials such as clean sands (Rausche et al., 2004)."

Jan 1, 1900

By Monica Prezzi

"Auger cast-in-place (ACIP} piles and drilled displacement piles are being increasingly used as foundation elements for structures, particularly in projects requiring accelerated construction or involving the rehabilitation of foundations of existing, overstressed structures. Auger cast-in-place piles (also referred to as continuous-flight-auger piles) are widely used to construct the foundations of all types of structures. There are many different types of drilled displacement piles, with the installation methods varying according to the equipment used. Depending on the specific rotary piling technology used, responses ranging from those associated with non-displacement to those associated with full-displacement piles are obtained. Conventional pile design methods do not account for how the various construction techniques involved in auger piling change the soil state around the pile during installation and, hence, cannot accurately estimate the pile resistance in a consistent way. Research on this subject, identifying the different variables that must be accounted for in design and linking these variables to installation methods, is lacking. This paper describes the different piling methods available for auger cast-in-place and drilled displacement piles, the equipment used to install them and the quality control processes typically used. It also reviews some of the design methods currently used.IntroductionDeep foundations are extensively used in geotechnical engineering practice. The wide spectrum of piling methods results in a variety of pile types. Each type behaves differently, depending on the installation or construction methods. On one end of the spectrum are non-displacement piles, the classicql examples of which are bored piles or drilled · shafts. These piles are constructed by removing a cylinder of soil from the ground and replacing it with concrete and reinforcement. On the other end are full-displacement piles, such as closed-ended pipe piles or precast reinforced concrete piles, which are typically driven into the ground. Driven piles preload the materials below the toe of the pile and displace the soil surrounding the pile shaft laterally during the installation process. Therefore, displacement piles are, in general, more likely to have a stiffer response than non-displacement piles. This is true particularly in the case of sandy soils where displacement causes densification."

Jan 1, 2005

By Venkatesh S. V J, Shubha M, Srilakshmi G

Choosing for the best option of pile foundations to overcome large lateral and uplift loads for the foundations in transmission line towers/offshore environment is still being a concern to achieve the required capacities but also by considering the suitability aspect in the environment. The objective of this paper is to review the methods that have been done for knowing the uplift resistance and lateral resistance of pedestal piles. Investigations by different methods such as experimental studies, numerical and analytical studies have been done by various researchers in order to evaluate the response of a belled pile. These methods are discussed in this paper and the comparison with straight shaft pile based upon the test and analysis. The results indicated that the uplift resistance and lateral resistance were significantly increased with the adoption of belled piles than straight shaft piles.

Sep 1, 2022

By Scott Dodds

"The Oxford Hydroelectric Station was a unique project that incorporated a variety of dam strengthening methods to stabilize the facility in order to meet the standards required by Federal Energy Regulatory Commission (FERC). The dam stability and Probable Maximum Flood (PMF) remediation work consisted of (1) construction of a new emergency spillway; (2) installation of 75 high capacity rock anchors; (3) construction of an anchored concrete powerhouse buttress; (4) construction of cast-in-place and sheetpile flood walls; and (5) design and construction of a permanent soil nail wall. INTRODUCTIONThe Oxford Hydroelectric Station is one of 11 hydroelectric facilities owned and operated by Duke Power along the Catawba/Wateree River. The Catawba River originates in the foothills of the Appalachian Mountains just west of Morganton, North Carolina. The river flows east out of the mountains and, at a point just below the Oxford Dam, the Catawba River turns and heads southeast. The Catawba River continues to flow southeast past Charlotte and into South Carolina where it eventually becomes the Wateree River. The Wateree River eventually flows in to the Atlantic Ocean.Located a few miles east of Hickory, North Carolina, the Oxford Dam and Hydroelectric facility is in the upper reach of the Catawba River. Oxford Dam creates the third impoundment along the river known as Lake Hickory. Lake Hickory is well known locally for providing many outdoor activities such as boating, jet skiing, canoeing and fishing. The dam and powerhouse were put into operation in the spring of 1928.Key features of the dam include a short embankment section on the south end of the structure, a 391-foot (119m) long south bulkhead and powerhouse, 540-foot (165m) long gated spillway section and a 235-foot (71.6m) long north bulkhead. The maximum height of the dam is approximately 100-feet (30m) from the crest to the dam/rock interface. (See Figure 1).The work associated with this project is the result of licensing requirements of the Federal Energy Regulatory Commission (FERC) which mandates that all hydroelectric facilities have the capacity to safely discharge runoff created by a critical rainfall event defined as the probable maximum flood (PMF). Duke Power, a division of Duke Energy (DUKE) submitted an initial PMF report in 1992 which indicated that at the Oxford Dam would be overtopped by approximately 10-feet of water during the modeled PMF event. Given the duration and depth of the overtopping, significant damage to the facility and a possible breach could result. Therefore, modifications to the existing facility were necessary to satisfy the report of the PMF model."

Jan 1, 2005

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017