Search Documents

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013

By T. Hidayat, D. Shishin, S. Sineva, M. Shevchenko

The effects of the slagging components Al2O3, CaO and MgO on the thermodynamics and phase equilibria of the gas/slag/matte system with major elements “Cu2O”-“FeO”-SiO2-S are characterised using an integrated experimental and thermodynamic modelling approach. The experimental technique included high-temperature equilibration experiments using a spinel substrate in controlled gas atmosphere (CO/CO2/SO2/Ar), quenching of the sample and subsequent measurement of the compositions of equilibrium phases with Electron Probe X-ray Microanalysis (EPMA). Thermodynamic modelling is undertaken using the computer system FactSage. In previous experimental studies on this system, the separate effects of Al2O3, CaO and MgO were determined. In the present investigation, the combined effects of these additional components are investigated at 1200oC and P(SO2) = 0.25 atm and a range of P(O2)’s. Special attention is paid to ensuring chemical equilibrium is achieved in each case, for this reason possible kinetic factors are systematically analysed. The results obtained are presented in the form of graphs showing the compositions of matte and slag phases as functions of copper concentration (matte grade). The new experimental data are used for the improvement of the thermodynamic database for multicomponent copper-containing systems. The effects of the slagging elements on this multicomponent system will be presented in the paper. INTRODUCTION Whilst Fe-O-Si form the principal components of copper smelting and refining slags, additional impurities are present in industrial practice typically at 2–5 wt.% Al2O3, 1–4 wt.% CaO and 1–2 wt.% MgO levels (Davenport, King, Schlesinger, & Biswas, 2002). These elements are introduced into the slag as impurities in concentrates and other feedstocks, in fluxes added to the process and in refractory materials. Understanding, and accurate description, of the changes that take place in the smelting process in the presence of these additional elements is of major importance to the optimization of industrial operations. Although experimental data are available on slag/copper matte equilibria, further work is needed to accurately characterise the influence of Al2O3, CaO and MgO on phase equilibria and elemental distributions of elements in gas/slag/matte systems. The individual effects of the Al2O3, CaO and MgO slagging components on equilibrium phase assemblages under selected conditions have been quantified in a recent series of studies on the Cu–Fe–O–S–Si-(Al, Ca, Mg) gas-slag-matte-metal system (Fallah- Mehrjardi, Hayes, & Jak, 2018; Fallah-Mehrjardi, Hidayat, Hayes, & Jak, 2017a, 2017b; Hidayat, Fallah-Mehrjardi, Hayes, & Jak, 2018a, 2018b; Jak et al., 2016; D. Shishin, Decterov, & Jak, 2018; Denis Shishin, Hayes, & Jak, 2018). Since, thermodynamically, the condensed phases do not behave ideally, it is to be expected that the effects of individual elements may not be additive, and the additional interactions between the Al2O3, CaO and MgO slagging components will also have to be taken into account. These additional effects are expected to be smaller than those of the individual components, so higher accuracy is needed. The present paper describes analysis of the precision and accuracy of the experimental technique on multi-component, multi-phase equilibria in these systems to enable the combined effects of Al2O3 + CaO + MgO on slag/matte/spinel equilibria, i.e. for high Fe/SiO2, to be accurately measured. The effects of Al2O3, CaO and MgO on the gas - slag - matte are analysed using a thermodynamic modelling approach with the computer package FactSage.

Jan 1, 2019

By Marc Legault

The Duparquet mining camp situated along the Quebec segment of the Porcupine-Destor Fault was the site of gold exploitation from 1933 to 1956 and 1988 to 1991. Numerous gold showings and deposits straddle the fault. An ongoing regional metallogenic study by the Quebec Geological Survey has identified five main types of gold mineralization, each showing a distinct style, alteration, control, metal content, and timing. In order to maximise the impact of this study, a 3D regional common-earth-model was constructed along a critical segment of the Porcupine-Destor Fault with the gOcad® technology. The realisation of this model required the maximum use of the public SIGEOM numerical database, as well as the recovery of significant private data from exploration company partners. The 3D model is also a powerful new dynamic exploration tool, which can be queried using geological criteria characteristic of the different gold deposit types. This 3D model can be modified and improved continuously by adding data from new drilling, mapping or geophysical surveys. The case of the Porcupine-Destor Fault illustrates the importance of 3D common-earth-modelling in delivering refined technological geological syntheses likely to attract significant investments from the mining exploration industry, especially for deep exploration programs within mature mining camps.

May 1, 2004

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008

By L. Li

The backfilling of underground stopes is a common practice throughout the mining industry. The stresses imposed by the backfill on the surrounding rock mass need to be assessed because of their influence on ground stability and on the hydro-geochemical response of the fill material. There is, however, a complex interaction between the relatively soft backfill and the much stiffer adjacent rock mass. In recent years, the authors have presented results from investigations conducted on stress distributions (obtained numerically and analytically) in and around backfilled stopes with (sub)vertical walls. In this paper, the influence of stope inclination and of backfill properties is evaluated. Results indicate that, in general, the vertical and horizontal stresses in inclined stopes are close to, but somewhat smaller than the stresses in vertical stopes. Nonetheless, significant differences can be observed in some cases, especially for the vertical stress along the inclined central line and along the hanging wall. It is further shown that neglecting deformability in limit equilibrium analyses is an acceptable assumption. However, Poisson?s ratio and the dilatancy angle, usually neglected in limit equilibrium analyses, may have significant effect on the stress distribution. Results also confirm that the backfill strength parameters (cohesion and friction angle) are critical factors required to properly evaluate the stress distribution, at least within a certain range of parameter values.

May 1, 2007

By T. W. Wloder

During recent studies concerning the effects that various surface treatments, surface imperfections, locked-in residual stresses and metallurgical and geometrical notches have upon the mechanical behaviour of metals and, in particular, upon their tension-bending characteristics under impact loads, it became apparent that specially developed methods and samples would be of great assistance in determining the desired data. This paper describes and discusses a number of different types of double-notched tension-bending impact samples which have been considered and examined for this purpose. The types most suitable for exploratory investigations are proposed for application in the study of the _behaviour of metals, their welds, and, in particular, their surfaces, when subjected to various notch-severities, surface imperfections, strain rates, temperatures, and constrained states of stress (i.e. the relations of the three principal stresses). It is expected that the proposed double-notched tension-bending samples and the proposed test methods will also contribute toward further understanding of the cold brittle behaviour and the notch-sensitivities of metals. The possibilities of introducing the so-called impact notch-sensitivity index and relative impact notch sensitivity of metals are discussed. Data obtained on double-

Jan 1, 1961

By Claude Deveau

"With ever decreasing feed grades, finer mineralogy and increased demand for product, it became obvious that a major step in equipment performance was required to reduce operating costs and increase production. Offsite testwork indicated that a Centrifugal separator was capable of recovering fine tantalum and that the newly developed C Series Falcon concentrator would be capable of replacing many pieces of aging equipment and provide improved performance. Further investigation led to the rental and the purchase of a Falcon C20 concentrator followed by a C10 to maximize circuit performance.Falcon Concentrators Inc’ s practice of working with the customer mirrors Tantalum Mining Corporation of Canada’s (Tanco) philosophy of continuous product development. This synergy honed valve design for continuous operation in a highly abrasive ore environment.Tanco has recently purchased two more Falcon concentrators for the recovery of additional tantalum from its spodumene circuit. These new units have additional user friendly operating features partially based on developments made at Tanco.The Falcon C Series units have enabled Tanco to maximize recovery of tantalum that was otherwise lost while using the original conventional gravity circuit."

Jan 1, 2000

By A Palynchuk

The development of welded pipe has paralleled the general industrial development and, in particular, that of the petroleum industry. The petroleum industry's need for high-grade, economical pipeline material to make many 'of its projects feasible has been a significant factor in the development of light-wall, high-grade welded pipe. The modern welding processes, such as high-frequency, electric resistance, flash, submerged arc, etc., have some basically different characteristics. The modern high-frequency weld mill is a complex of specialized equipment that is integrated into a production unit. Each component in the unit performs a specific function in the production process. Quality control must be built into the process on an operating basis and, to maintain the quality required for pipeline standards, must be more than a policing operation. The further development of the welded pipe industry will be determined by changing and increasing demands. The technical and economic views and requirements that will influence the development have to be resolved.

Jan 1, 1964

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By J. Coffin, R. Multani, C. Deredin

Glencore’s Strathcona Mill has recently evaluated a pyrrhotite depressant combination of diethylenetriamine (DETA) and sodium metabisulfite (SMBS) to improve its overall plant pyrrhotite- pentlandite (Po-Pn) selectivity, with the aim of producing a higher quality nickel concentrate. In a previous paper, key findings from a comprehensive lab-scale program (completed at the XPS Centre) were summarized where, of the depressants tested, DETA/SMBS combination was found to be the most effective in improving the Po-Pn selectivity. The present paper describes the metallurgical program recently completed at Strathcona Mill; DETA/SMBS evaluation on select plant “grab” samples as well as the major results of three DETA/SMBS plant trials conducted on several plant ore feeds (long-term testing). Interestingly, it was found that there was variable success in using DETA/SMBS depressants on the different plant ore feeds; DETA/SMBS (dosage: 25/50 g/t milled feed) on lower Cu feeds demonstrated a ~2% Ni recovery increase at the same Ni grade. On the other hand, higher Cu feeds demonstrated virtually no benefit from DETA/SMBS at the same plant dosage, suggesting that higher DETA/SMBS dosage (at specific locations) than that tested is required to overcome the increased Cu-DETA complexation for these particular feeds. Glencore Nickel – Sudbury Integrated Nickel Operations owns and operates Strathcona Mill which has been processing Ni-Cu ores from the Sudbury Basin since 1968. The valuable sulfides are pentlandite (Pn) – (Ni,Fe)9S8 and chalcopyrite (Cp) – CuFeS2, majority of the sulfide gangue is pyrrhotite (Po) – Fe(1-x)S [0 < x ≤ 0.125] which is present in two forms: hexagonal Po (Fe9S10) and monoclinic Po (Fe7S8) (Multani & Waters, 2017; Lawson et al., 2014). Currently Strathcona Mill processes ore mined from two primary sources from the Sudbury area and produces two concentrate streams: (1) nickel-copper concentrate that is sent to the Sudbury Smelter; and (2) copper concentrate that is shipped to the Fonderie Horne (Glencore Copper, Rouyn-Noranda).

Jan 1, 2019

By Å. Kruukka, H. F. Broicher

The iron ores of the Kiruna mine in Sweden are of exceptional quality except for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998, LKAB has been testing prototypes of LIF (laser-induced fluorescence) analyzers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground, the mining engineer supports the efforts of the metallurgist in the processing plant.

Jan 1, 2002

By S. V. Burr

"A 28-year study of cross folds leads to the conclusion that the northwest-southeast folds recognized in many areas of North America are part of a regional pattern. Detailed examination of over 650 geological maps and reports of Ontario indicates that this folding can be traced across the province. Evidence is presented that this fold pattern played an important part in determining the pattern and scale of intrusion, that its recognition in the field can aid in defining stratigraphy, folding and faulting, and that it may have played an important role in channeling hydrothermal or magmatic mineralization. IntroductionThe concept of regional cross folding in Ontario is not new. W.H. Gross (1955) discussed regional cross folds in the Archean of Northwestern Ontario, and A.M. Goodwin (1961) referred to regional cross folds in the Archean of Ontario and Quebec. However, the interpretation in this paper is new.The writer saw a cross fold for the first time, underground, at Little Long Lac Gold Mines in Geraldton, Ontario, in 1951. This recalled the ""transverse folds"" on E.R. Faribault&apos;s classical maps of Nova Scotia, published by the Geological Survey around the turn of the century; M.E. Hurst&apos;s cross fold(s) at Timmins, Ontario (Figure I); and the cross folds mapped by A.W. Jolliffe in the Yellowknife area of the Northwest Territories. All these mapped cross folds had one thing in common with the fold at Little Long Lac: A northwest-southeast axial trend. Were such cross folds of purely local extent, or might they be indicative of a widespread regional fold pattern? If so, has such folding any significance for mineral exploration or potential?By 1959, based on a study of about 1000 Canadian geological maps and reports, including 291 in Ontario, the writer reached the conclusion that cross folding trending northwest-southeast is so widespread as to constitute a pattern of folding, and that such cross folding should produce changes in plunge along pre-existing greenstone fold belts."

Jan 1, 1980

By A. M. Krzanowski, T. S. Golosinski

"This paper presents results of a study undertaken to determinethe feasibility of mining plains overburdens with bucket wheel excavators. Based on extensive geotechnical testing of overburdens under study, the relations between material geotechnical properties and its cuttability were defined. The properties with the highest correlations to the cuttability werethen used to develop the material diggability classification. This classification may be used for identification of overburdens and coals mineable by bucket wheel excavators.IntroductionLow cost of mining and high productivity can be achieved when mining unconsolidated soils and soft rocks with bucket wheel excavators. As a result this mining equipment will likely be introduced into plains coal mines. At present there are plans to use a bucketwheel excavator (BWE) in at least one mine by the end of this decade. Unfortunately, the performance of a BWE deteriorates rapidly with the increasing strength of mined material. To avoid costly misapplication, material diggability must be defined in advance of an application (i.e. the force required at the cutting edges of BWE buckets must be quantified). Correct definition of material diggability permits reliable selection of a BWE, or may indicate unsuitability of this equipment for a particular application.The reported studyu i was undertaken to investigate the diggability of typical prairie overburdens and thus provide a guidance for likely future applications of bucketwheel equipment. Investigations concentrated on the parts of overburden most likely to create problems for a BWE mining. These are defined in Table 1. At present, thin layers of the two investigated materials (samples K and L) are mined by a BWE in an oil sand mine, after being loosened by blasting."

Jan 1, 1987

By André Laplante, Robert C. Dunne

"The role of flash flotation in precious metal recovery is reviewed. Interacting flash flotation and gravity recovery is discussed. The GRG test can be used, when linked to the behaviour of gold in grinding and classification units, to predict the recovery of GRG by flash flotation. The Cadia mill in New South Wales is used as a case study of circuit design, performance and simulation. It is shown that high throughput coarse grind applications such as Cadia require very effective fine GRG recovery systems in the primary grinding loop, which are more consistent with flash flotation than batch centrifuge concentrators (BCCs). BCCs can effectively recover a significant fraction of the GRG from flash concentrates, as predicted by laboratory testing and confirmed at a growing number of mill sites.INTRODUCTIONThe GRG test was designed to characterize Gravity Recoverable Gold (GRG) ten years ago (Woodcock and Laplante, 1993; Laplante et al, 2000), in response to the need to predict how much gold could be recovered from the main circulating load of grinding circuits using centrifuge concentration. The amount of GRG is not itself a prediction of gravity recovery: the performance of a gravity circuit nested in a circulating load also depends on the type and size of unit used, how much of the circulating load is treated, and how many times GRG is recycled and presented to the recovery circuit. The GRG test was first used in a simulator to predict gravity recovery (Laplante et al, 1995), and indeed most of the early tests targeted ores or prospective ores for which gravity recovery was an obvious match. As the test became more accepted, more and more samples returned a verdict that precluded the use of gravity recovery, or made it marginal. Typically, such ores are either copper-gold or base metal ores in which the GRG content is often fine (largely below 105 um) and ranges from 8 to 33%. Extensive simulation and plant sampling tests, either published (Laplante et al, 1997) or proprietary, show that full scale gravity recovery for these applications is generally below lo%, and can be as low as 2%. Not in all cases are such low recoveries economically unjustifiable, since there is documented evidence (Darnton et al, 1992) that a significant proportion of the gold recovered, at least in the case of base metal ores, would not have reported to the copper or zinc concentrate and received NSR credits."

Jan 1, 2002

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By John G. Henning

The Porcupine Joint Venture operates the Dome Mine in South Porcupine, Ontario. Dome underground began production in 1910. It is the longest continuous operating gold mine in Canada, producing in excess of 15 M ounces. More than 900 underground stopes have been mined and hundreds of miles of drifts, sublevels and raises developed. Underground mining methods included shrinkage, cut and fill and longhole. Not all stopes were backfilled upon completion, particularly the longhole stopes. The Dome open pit was designed above the underground mine workings such that, as the pit is excavated, it intersects underground drifts and stopes. Potential operational problems associated with the interactions between the stopes and the pit walls may occur, necessitating pit wall redesign, ground support installation and operational rescheduling. Each intersection of the pit with the underground mine workings is closely evaluated to maintain a safe working environment and wall stability. This paper discussed how risks to pit wall stability are assessed, mitigated and monitored.

May 1, 2004

By S. C. Richardson

The electrowinning (EW) circuit involves using DC current in the electro-deposition of metal ions dissolved in an electrolyte solution. This paper reviews a method to generate an electrical model of an EW circuit and the resulting DC current flow and voltage distribution within the circuit. Topics include: calculations of electrolyte conductivity and the equivalent electrical resistance of the electrolyte within the electrolyte pipelines connected to the EW circuit; the breakdown and classification of the EW cell voltage into thermodynamic and ohmic potentials; methods to calculate current flow and voltage distribution throughout the EW circuit; and the development of an interactive visual computer model to simulate an actual EW circuit. Stray current can pose an electrical shock hazard to employees in electrolytic tankhouses. Increased awareness and understanding of the voltage distribution and potential stray current in an EW circuit can help mitigate the risk of tankhouse workers becoming exposed to electrical shock hazards. INTRODUCTION Copper electrowinning tankhouses include rectifiers that deliver large amount of DC current to a series of electrolytic cells consisting of electrolyte solution and electrode pairs. The design also includes metallic conductors in the circuit which include the rectifier’s positive and negative busbar, inter-cell busbar, and the anode and cathode frames. The electrolyte acts as an electrical conductor that transfers current via ions between the anodic and cathodic electrodes within the cell. Electrolyte, as a conductor, is also capable of conducting DC current outside the main EW circuit through the connected electrolyte feed and return pipe systems. DC current that follows a path other than the intended path through the series of electrolytic cells is referred to as “stray current”. Developing an electrical model enhances understanding of voltage distribution and current flow in an EW circuit. This paper discusses the derivation of the various representative components of the model as well as the output from the model. An interactive visual computer simulation incorporates the model output in order to aid in the understanding of voltage distribution and current flow throughout the EW circuit.

Jan 1, 2019

By Jean Cayouette, Paul Blatter, Paul Cousin

"The Laronde mill was commissioned in 1988 and has been treating the Laronde Penna ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually.In 2008, the Goldex plant began trucking high grade (35-45 g/t Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold grade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine.Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa).INTRODUCTIONFollowing the 2000 to 2003 expansions, the Laronde plant evolved into a mature milling complex with developed processing, man power, and water treatment capabilities able to accommodate the complex Laronde ore. The ore requires a series of grinding, copper/lead flotation and separation, zinc flotation, zinc tails precious metals leaching, followed by a counter-current decantation circuit and Merrill Crowe precipitation. A paste backfill and SO2-air cyanide destruction operate intermittently. The tailings area has a dedicated cyanide destruction and metals precipitation plant prior to water recycling to the mill. A biological water treatment plant was put into service in 2004 to address the build-up of thiocyanate in the tailings ponds at Laronde. This was the result of the high sulphide content of the Laronde ore and 90% recirculation of the process water. The plant uses bacteria to oxidize and destroy thiocyanate, and removes phosphate from the water before it is released to the environment."

Jan 1, 2011