Search Documents

By A. C. Atenas

The majority of refineries that operate with traditional starting sheet technology ?starting sheet- uses a relatively low current density of 250 A/m2. Industrial tests at high current density with conventional technology were carried out in Refinery of Potrerillos, getting satisfactory results that are similar the results obtained with permanent cathode technology. The series of copper refining electrolyses electrolysis trials were carried out between 300 to 325 A/m2. Electrolysis conditions, in accordance with industrial practice, were kept constant in all sets of experiments and were as follows; 45 g/L Cu 2+, 210 g/L H2SO4, 62 °C, electrolyte circulation of 14-18 L/min. The same Dosing dosing of Additives additives used in permanent cathode technology was required in these tests. In general, only not importantminor operational modifications were necessary in comparison to normal practice in the Refinery to assure the good results. Different quality of starting sheet and anodes were examined. The test included starting sheets from smelter and laminated process. Results indicate that the charge physical quality of the electrodes and the control of the process during the two first days of operation are the keys to get the best results.

Jan 1, 2007

By E. You

Kennecott Utah Copper Refinery and Outokumpu Technology have developed a wireless Electrolytic Cell Monitor (CellSensor) system to monitor cell voltage and temperature. The system is based on a robust self-organizing and self-healing wireless network with a very reliable redundant structure. The microprocessor controlled CellSensor device operates off a small amount of energy harvested from the cell bus and requires no external power source. The radio works in the 2.4 GHz international ISM band using robust Spread Spectrum technology. The CellSensor does not require end user calibration of either the voltage or temperature sensors and accuracy is superior to previous systems. The on-board computation power allows digital filtering of the cell voltage signal which results in very high quality data. The system requires much less maintenance than conventional hardwired systems and is intrinsically safer since no high voltage isolation is required. The advanced diagnostic functions allow the device to determine if the bus tap contact is degrading. The CellSensor can also be used for monitoring electrowinning (EW) cells for a variety of metals. CellSensor have been tested for over two years at the Kennecott Utah Copper and Boliden Harjavalta Pori refineries. The CellSensor system is now commercially available through Outokumpu Technology.

Jan 1, 2007

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By Ali Bunjaku, Lauri Pesonen, Hannu Johto

It is well known that there are many ways to process copper concentrates into copper anodes using the pyrometallurgical route. All modern copper smelting technologies are fundamentally energy efficient and environmentally safe options, and therefore choosing one depends on the desired capacity range, feed impurity levels, plant location, flexibility needs, overall energy use, and of course smelter economics in both the short and long term. This paper focuses on comparing different solutions which have potentially the lowest variable opex (operational expense), meaning in practice finding out which technology offers the best chances for profit maximization under certain scenarios. For the comparison, we chose to have a closer look at Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC), Outotec Flash Smelting (FSF) – Outotec- Kennecott Flash Converting (FCF), Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC), Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF), Mitsubishi Smelting Process (MIT), Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC), and Side Blowing Furnace (SBF) - Top Blowing Converting (TBC) since these seem to be the main state-of-art technologies now being applied in many recent copper smelter projects around the world. The work was carried out by modelling each smelting route by using the new HSC SIM 9 simulation software and applying operation time, energy, and consumables consumption numbers for each unit process and stream. Combined with cost data, the exercise produced a rich set of information which will be shown in detail for each area per scenario. The authors’ goal here was to provide a fair comparison where each technology can be evaluated from various perspectives such as electricity use or refractory consumption. INTRODUCTION Copper can be produced either pyrometallurgically or hydrometallurgically. The hydrometallurgical route is used only for a limited amount of the world’s copper production (~20%) and is normally only considered in connection with in-situ leaching of copper ores. On the other hand, most of the copper extraction from Cu-Fe-S minerals is pyrometallurgical (~80%) (Schlesinger 2011, ICSG 2017). Thus, several different processes can be applied for copper production, including the following state-of-the-art technologies: Outotec Flash Smelting (FSF) – Outotec-Kennecott Flash Converting (FCF) Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF) Mitsubishi Smelting Process (MIT) Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC) Side Blowing Furnace (SBF) - Top Blowing Converting (TBC)

Jan 1, 2019

By R. Erpelding

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By George J. Cymerman

Since 1978, Syncrude Canada Ltd. has been expanding steadily its oil sand mining and processing capacity while reducing unit energy requirements. At the current rate of ~180 M tonne/year oil sand, the originally adopted Karl Clark?s 80°C version of the Hot Water process would require some 53 PJ (53 x 1015 Joule) heat. If this amount of heat were to be derived from burning natural gas it would cost $369 M/y (at $7/GJ). Fortunately, effective recovery of waste heat from the upgrading operations at the Mildred Lake site obviated the need for water heating with natural gas. The oil sand hydrotransport technology, first utilized commercially in the mid-nineties at Syncrude?s North Mine, reduced slurry temperature from ~80°C to ~50°C, cutting the unit heat requirement from 293 MJ/tonne to 183 MJ/t. However, in the new 100 Mt/year Aurora Mine even a 50°C process temperature would still require 18 PJ of heat energy per year. Only limited quantity of 65°C water could be imported from Mildred Lake site and some waste heat would be available from Gas Turbine Generators. A new, Low Energy Extraction (LEE) process was developed to minimize heat requirements by further reducing process temperatures to 25°C in the slurry pipeline and 35°C in the Primary Separation Vessels (PSV). Unfortunately, when applied to certain ore facies in Aurora, the LEE process yielded disappointing bitumen recoveries, necessitating an increase in slurry temperatures from 25°C to 35°C in the pipeline and from 35°C to 42°C in Primary Separation. In 2004, an Optimized Low Energy process (OLE) was developed and piloted at Syncrude Research using a 2000 kg/hour pilot plant. In the OLE process, most available heat is applied up-front to produce 45°C pipeline slurry at a density of 1.58 kg/l. Once the pipeline conditioning process is completed, the slurry is flooded with cold (10°C) water, resulting in PSV temperature of 34°C. The overall heat and water requirements are the same, or slightly lower, compared to those of the LEE process ? but without the penalty in bitumen recovery. Processing 100 Mt oil sand at 34°C (96 MJ/t), rather than at 50°C (183 MJ/t), will save $61 M/y (@ $7/GJ) and reduce green house gas emissions by ~47 %. The OLE process is currently being implemented at the Syncrude Aurora Mine.

May 1, 2006

By John Mair

The Ilimaussaq Intrusive Complex in south Greenland is a layered alkaline igneous body that is predominantly comprised of agpaitic nepheline syenites. The Complex is now recognized as containing vast resources of uranium in polymetallic ores that are also strongly enriched in rare earth elements (REEs) and zinc. Uranium and REEs are dominantly hosted in phosphate minerals with a minor proportion hosted in zirconium silicate minerals. Equivalent ores are yet to be mined for uranium anywhere in the world; however, studies are well advanced in confirming a process route to economically extract uranium. The Ilimaussaq Complex is considered the world?s type-locality for agpaitic rocks. Formation of the complex is attributed to four successive pulses of magma. The first produced an augite syenite, which now forms a marginal shell. This was followed by intrusion of a sheet of peralkaline granite. The third and fourth stages make up the bulk of the intrusion and are peralkaline to hyper-agpaitic in composition. The third batch of magma differentiated to produce pulaskite, foyaite and naujaite. Stage four produced the kakortokites and lujavrites, which are the units of particular economic significance. Kakortokites are strongly enriched in zirconium, niobium and tantalum, whereas the lujavrites are strongly enriched in uranium, rare earth elements, fluorine and zinc. Lujavrites are vertically zoned with arfvedonsite (black) lujavrites grading downward into aegerine (green) lujavrites. The upper most portions of the black lujavrites contain uranium concentrations of greater than 450 ppm, which decreases toward green lujavrites where uranium concentrations rarely exceeds 200 ppm. Resources defined to date in accordance with the Australian JORC code include 282 M lbs of uranium oxide at a grade of 280 ppm. With scope for several other similar sized resources within complex, the overall potential resource is of immense global significance. Metallurgical studies to date indicate that uranium can be successfully extracted from black lujavrites via an alkaline pressure leach method. This involves selectively leaching uranium with solutions containing carbonate and bicarbonate at elevated temperature and pressure. Uranium can then be recovered by hydrogen reduction to create a uranium oxide product. There is also scope to beneficiate ores as uranium and REE?s are hosted in specific mineral groups. Phosphate minerals can be effectively concentrated by froth floatation and uranium-bearing silicate minerals can be concentrated by gravitational methods. Studies indicate that REEs can be extracted from the residue following the alkaline leach process by a dilute hydrochloric acid wash, with REEs then precipitated in the form of a REE concentrate.

Aug 1, 2010

By R. W. Seedsman

In 1984 and 1985, two 7.6m diameter TBM tunnels were driven from the Donkin-Morien peninsula in Nova Scotia to access the Harbour coal seam. The design of the ground support was based on identifying zones of rock failure through the application of the Hoek Brown failure criterion and the early use of finite element analyses. In 1992, the mining project was abandoned and the tunnels allowed to flood. Monitoring data from the tunnel was subsequently used as a case study in the development of the concepts of brittle rock behaviour. In 2007, the tunnels were pumped out as part of a feasibility study into the reintroduction of longwall mining into the coalfield. There is a good match between observations of the collapse zones in the roof and sides of the tunnel and a simple elastic analysis using brittle parameters, a spalling limit of 5, and a low independent shear modulus. The brittle analyses form the basis of the design for the resupport of the tunnels.

May 1, 2009

By Robert B. Parsons

"The Whitehorse Mining Initiative (WMI) brought together all of the key stakeholders in Canada's mining industry to develop a framework whereby the industry can meet the challenges that it faces into the 21st century. The WMI Accord7 which was signed at the annual Mines Ministers Conference in Victoria, British Columbia, on September 137 1994, touches all of the important issues that confront the industry, including taxation. IntroductionSeptember 13, 1994, was a historical day for Canada's mining industry. On that day, on the occasion of the annual Mines Ministers Conference in Victoria, British Columbia, the Whitehorse Mining Initiative (WMI) Accord was signed by the leaders of the five principal stakeholders in the industry: industry; government; labour; environmentalists; and aboriginals. The Accord is the culmination of two years of hard work and intense collaboration by these stakeholders. But, the Accord is not the end result. The Accord can better be described as a springboard to a prosperous future for mining in Canada.The WMI had its beginnings at the Mines Ministers Conference in Whitehorse, Yukon, in September 1992 (hence, the name of the initiative). At that time, the mining industry was well aware of the serious challenges facing the industry, including significantly increased competition for mineral investment from other mining countries, coupled with an atmosphere of uncertainty surrounding land access, environmental regulations, and taxation. The diversion of investment abroad was hurting, and would continue to hurt, all Canadians. Something had to be done. At the 1992"

Jan 1, 1994

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By L. Mercier, R. Narendrula, F. Desmarais, L. Amaratunga, A. Aledresse

Thiosulfate is recognized as a promising alternative lixiviant to cyanide for the extraction of gold from ore bodies. Gold thiosulfate ([Au(S2O3)2]2), however, is not well-adsorbed by activated charcoal, making industrial scale use of thiosulfate for gold leaching impractical at present. Because of their high specific surface areas (500-1000 m2g-1) and uniform open-framework nanoporosity (pore channel diameters in the range 3-10 nm), functionalized mesoporous silicas are widely recognized as highly effective materials for the selective, rapid and high capacity uptake of mercury, gold and platinum group ions. In the present work, the efficient and rapid adsorption of gold thiosulfate by thiol-functionalized mesoporous silica (hereafter designated MP-HMS) is demonstrated, whereby the thiol groups in the materials bind with the gold complexes by ligand displacement. The adsorbed gold could be leached out using cyanide, regenerating the adsorbent for further uptake cycles. Functionalized mesoporous silica is thus a promising candidate for the preconcentration of gold from thiosulfate leachate solutions.

Jan 1, 2011

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994

By Paul M. Lévesque

The Dome Mine has been in production for nearly 100 years and throughout the years many different mining methods were used to extract the ore. An exploration program late in the 1990s outlines new resources requiring the mine to extract the rock and some previously placed backfill (alluvial sand and/or classified tailings). It is therefore imperative to separate the backfill from the rock to reduce the negative impacts of handling the backfill on the ore pass, crushers and mill processes. Separating the backfill from the ore at the source would also reduce and/or eliminate the cost of handling this waste stream. The paper will touch on the backfill removal criteria, the risks, the alternatives and the selected method, screen decks, for backfill removal at the Dome Mine. The 155549 bulk zone case study will illustrate how the screen decks are in use at the mine. The paper will also illustrate how the lessons learned and conclusions of the work done for the 155549 bulk zone were applied to the second screen deck installation for the 257260 bulk zone.

May 1, 2009

By John Rowson, Caitlin Brown, Kebbi Hughes, Joseph Esslifie-Dughan

The McClean Lake mill in northern Saskatchewan, Canada, is operated by Orano Canada Inc. and has been in production for the last 20 years. The tailings preparation process at the mill has been designed with decommissioning in mind, to produce tailings that are geochemically stable over the long-term within the site’s tailings management facility. Twenty years of study have contributed to a detailed understanding of geochemical and geotechnical properties of the McClean Lake tailings. Validation of the tailings properties has occurred through in-situ sampling campaigns conducted initially every year, and later every five years. Each sampling campaign has applied the same rigorous sampling procedure to provide data with useful correlations year over year. Each campaign result compares elements such as the inherent variability of the tailings, consolidation of the tailings and variations in the tailings placement methods. We will discuss lessons learned from seven sampling campaigns over 20 years and present data to show the reliable tracking of geochemical evolution of the in-situ tailings over time; providing opportunities for continuous improvements.

Jan 1, 2020

By J. Kicki

The paper depicts the current status of the EKSPERT mining machinery management system and shows the prospects for its further development. The system is the result of a rare attempt to utilize the comprehensive dataset; this refers to a precisely identified group of users and is used to develop a solution with a scope that encompasses other areas of activity within the company. The authors present the incredible flexibility and usefulness of the system used at KGHM Polska Miedz S.A. for everyday control of the mining machinery fleet. The issue of visual aspects of the reports generated by the system is handled separately and used as a tool allowing for implementation of the methodological assumptions of EKSPERT. A concept for creating a system for assisting decision making in the process of mine management with the use of IT tools and production monitoring is also discussed. The solution is based on integration of information from both the monitoring field and visualization of the technological process around the Production Reporting Center.

Aug 1, 2013

By Tao Cheng

Previous research and applications in construction resource optimization have focused on tracking the location of material and equipment. There is a lack of studies on automated monitoring of the interaction between workers and equipment for safety purposes. This paper presents a new approach for measuring the safety performance of construction personnel particularly when they work in very close proximity to moving equipment as well as static hazards such as chemical and flammable substances. A method of generating hazardous zones according to the geometric and kinematic characteristics of the considered hazard is introduced. The spatio-temporal relationships between the hazardous zones and workers? positioning data collected by real-time location sensing technology are automatically analyzed. This approach has been validated in a controlled test bed environment that simulates a construction site. Results indicate that worker?s safety performance of selected activities can be automatically and reliably measured using the developed approach. Furthermore, a heat map is generated for visualizing proximity related issues in the test bed using the computed results.

Aug 1, 2013

By Changyoon Kim

Technological advances in mobile systems, such as smartphones and tablet computers, provide engineers with new opportunities to enhance the current facility management processes. Equipped with powerful system processors, touch screens, and wireless communication capabilities, mobile systems enable the experience of omnipresence of facility information. Building information modeling (BIM) also enables improvements in facility management. With an advanced data structure and visualization capacity, BIM can be used in numerous applications for facility management. This study aims to incorporate the strength of mobile systems and BIM in facility management. The proposed system, which utilizes smartphone technology, allows engineers to conduct facility management functions, such as maintenance planning, inspection, and assessment, irrespective of a user?s location. The integration of building information modeling in a system provides detailed visual information of the building components. A case study was conducted to verify the applicability of the mobile system in terms of the hardware functions, system design, and user interface. This proposed system, with its study results, provides a guideline as to how mobile systems can be effectively integrated with BIM for improved management of facility information.

Aug 1, 2013

By G. Gagnon

"HistoryMining of the Schefferville iron deposits began in 1954 on completion of the 357 mile railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at schefferville to develop a process for upgrading the extensive lower grade deposits containing 51% iron with 15% silica (natural analysis). Engineering for a six million ton per year beneficiation plant using cationic silica flotation and the A-C grate kiln Began in 1970 and the first pellets were produced in mid-1973.Production requirements and operating difficulties have restricted capacity to approximately 85% of design but on going improvements are being made continuously to attain design capacity.GeologyThe sedimentary ore bodies of the labrador trough occur in a belt 5 to 10 miles wide and 60 miles long and contain 51 individual deposits varying in size from 1 and 60 million tons. The ores are classified into three main color groups."

Jan 1, 1981

By R. G. Rosehart, S. Y. Lee

"The current investigation concerns the removal of arsenic from waste waters using ion-exchange resin and activated carbon as sorption media. Use of certain weak and strong base anion exchange resins permits the removal of arsenic. Arsenic may be loaded on the weak base resin in the pH range of 2 to 3 and on the strong base resin above pH 5. The elution of arsenic is successfully achieved using 0.5 M NaCl or a mixture of NaCl and NaOH. The activated carbon investigated was less effective on loading arsenic, but the arsenic loaded was easily eluted by simple pH adjustments."

Jan 1, 1972

By Marcel Vallée

"This text consists of two parts, comments on "Classification and Reporting of Mineral Resources for High-Nugget Effect Gold Vein Deposits," by S.C. Dominy, P.R. Stephenson and A.E. Annels, Volume 10, No. 3, pp. 215-233, and related comments on some features of the JORC Code.This paper is, in many respects, a very elaborate and valuable account of the problems encountered in the estimation and classification of high-nugget gold deposits. However, in some key areas, it appears to fall short of its objective to help "resolve satisfactorily most issues" and "contribute to improved estimation and classification" (abstract). One must realize that high-nugget effect gold deposits constitute a very narrow field, despite the occasional bonanzas. This is a field of mostly smaller sized deposits, where limited success and a significantly higher rate of failure occur relative to larger deposits of mostly lower grade. This is shown by the six deposits described in the paper. Thanks for contributing to greater understanding of these complex and nevertheless challenging deposits."

Jan 1, 2002