Search Documents

By Ali Roshanfekr

Linear mine-waste dumps at open-pit mine sites essentially represent expedient places to deposit large quantities of waste rock. Being in valleys in most cases, the effect of the water flowing through and out of the deposit often raises questions about their hydraulic behaviour and geotechnical stability, especially the zone of the downstream toe. In order to provide better tools to assess the behaviour of these dumps a laboratory and analytical study was conducted. Firstly, physical models were built to assess the flow capacity and hydraulics associated with the linear growth of such dumps. It was found that the elevation of the point of first-emergence on the downstream side becomes constant after the dump grows to a certain length, but that the upstream depth concurrently increases. The limits of applicability of the theories of Hansen et al. (1995, 2005) are discussed in this regard. Secondly, in analysing the seepageface downstream, two approaches for solving this spatially varied flow (SVF) problem were undertaken. Under one of the approaches links to SVF depths were merely made to the hydraulic heads of the body (interior) and flux was calculated using conventional surficial nodes after the fact, Under the other approach flux nodes were used to link the SVF algorithm to the hydraulic heads further ?inside? the body of the rockfill. Although there are inherent uncertainties, it was found that these two methods can be made to perform equally well. Research continues but it appears that a linear variation in depth can be assumed without inducing any unrealistic exit gradients in the zone of primary concern with respect to unravelling.

May 1, 2011

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By V. Songmene, A. Tahan, J. P. Michaud

The machining of thin wall parts, often used in the aeronautical industry still creates a number of problems, including panel deformation. Quality and productivity are often affected. This study seeks to determine the optimal conditions for cutting in order to guarantee a competitive fabrication of parts while still maintaining quality and delivery deadlines. The studied model (Spar) is a typical structural part used in the assembly of airplane wings. The main objective of this study was to improve two performance aspects: surface quality finish (quality criteria) and the rate of cutting by stock removal (economic criteria). To achieve this objective, we used an evaluation process of the geometrical error issuing from the machine-tool. We also determined the stability zones of the machine-tool's dynamic system. Finally, a series of high-speed machining tests (finishing cuts) were conducted using an experimental structured approach (16 000 - 24 000 rpm). Profile measures of surface roughness and cycle times registered during trials allowed us to establish optimal cutting conditions. Surface roughness improved as well as cutting by stock removal. Four parameters were taken into consideration: axial depth of cut, chip load, spindle speed, and cutting fluid. Finally, the influence of the type of cutting fluid was evaluated to show that it did not significantly affect machining results.

Jan 1, 2006

By Atsuki Sado, Akira Ueno, Kazuaki Takebayashi, Kunio Watanabe

The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® process in 2006 to improve product quality and productivity. After resolving various technical difficulties associated with the process, a current density of 325 A/m2 and electrolytic copper production of 234 000 tons per year were realized in 2018. In recent years, Saganoseki Smelter & Refinery has promoted treatment of recycled materials in addition to copper concentrates. Accordingly, the amount and type of impurities charged to the smelting process have tended to increase. In the electrorefining process, impurities such as nickel and antimony cause anodic passivation and formation of suspended solids, respectively. Although these undesirable phenomena can be avoided by controlling impurity concentrations in the anode and electrolyte to appropriate ranges, this also limits the choice of recycled materials that can be processed by the smelter. To achieve both stable operation of the electrorefining process and flexibility in treatment of recycled materials in the smelting process, Saganoseki Refinery improved the capacity of the impurity recovery processes during 2016 to 2018. This paper describes the expansion of the purification plant to remove and recover nickel and antimony. INTRODUCTION The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® (wax- less permanent cathode method) in 2006 to improve product quality and productivity. Since then, the refinery has gradually increased current density, and has been committed to establishing stable operation and high productivity via various improvements related to the electrolyte filtration and additive management systems. Figure 1 shows the trends of current density and current efficiency at the refinery. Although the current efficiency temporarily dropped when the current density was raised to 322 A/m2, it consistently exceeded 97% thereafter. At present, stable operation at 325 A/m2 has been achieved and continues.

Jan 1, 2019

By D. B. Dreisinger, A. A. Gunaratnam

A pressure oxidation (POX)-hot cure (HC)-lime boil (LB) process is used in industry to recover silver from refractory gold sulfide ores containing minerals such as pyrite and arsenopyrite. Pressure oxidation is used to oxidize minerals and liberate occluded gold particles. As such, iron goes into solution and under acidic and high temperature conditions often precipitates as basic iron sulfate (BFS). BFS consumes excess lime during neutralization prior to cyanidation. Therefore, a hot cure stage is required to re-dissolve BFS back into solution. BFS re-dissolution consumes acid and produces ferric sulfate. In the presence of silver, these conditions favor the slow formation of silver jarosite. Silver jarosite is refractory to cyanidation, and must be broken down prior to cyanidation. This is done in the lime boil to produce a cyanide-soluble silver hydroxide. A study was conducted to investigate parameters that affect the precipitates that form in each stage of the POX-HC-LB process.

Jan 1, 2017

By J. N. Cram

"The comments given are to help allay generally accepted ideas that the handling of arsenic as arsenic-trioxide (As2o3J in and from off gas pyrometallurgical operation fumes is difficult, hazardous and expensive. It need not be any of these things if the basic and rather unique chemic3l and physical properties are understood and taken care and advantage of through present day technologies. These particular characteristics are:-(1) As2o3 sublimes and re-condenses, at a relatively low temperature;(2) As2o3 is, for practical in-plant purposes, insoluble in water at ambient temperatures and quite soluble in water just below the boiling point;(3) residual suspended and dissolved As 2o3 can be removed from water by complete dissolution with very little sulfuric acid, followed by the addition of small amounts of ferrous sulfate and calcium chlorate, with oxidation to the ferric and arsenite state and precipitation of an insoluble ferric calcium arsenate, thereby lowering the As2o3 content of solutions to acceptable levels. Even lower levels of non-toxic forms of arsenic solids and residual As2o3 in the water solutions can be attained by also using phosphate, and lime, along with the above.A background re past arsenic processing methods, present day operations, plus predictions re future trends, and hazards, are outlined."

Jan 1, 1979

By B. W. Brooks

"After an extensive period of University research and field trials, large scale reclamation of the Waite Amulet tailings discharge areas commenced in the spring of 1978. The Noranda program consists principally of sampling the complete dam to determine the vegetation potential of the various areas, addition of the required amelioration materials, and the use of good agricultural practices. This paper describes the development work that led to the establishment of the Noranda-Guelph Contract and the subsequent findings concerning the revegetation of tailings dams. Current revegetation procedures are presented. INTRODUCTIONThe Amulet Mine Ltd. was staked in 1924 and by 1930 had constructed a small 300 ton per day flotation plant. During the late twenties and early thirties, Noranda Mines Ltd. increased its equity in the company to gain a sixty percent share of this small mine. In 1933 the mine was amalgamated with another small producer, the Waite Ackerman Montgomery Mine Ltd., which was more than eighty per cent controlled by Noranda to form the Waite Amulet Mines Ltd.An interesting historical side point to the story of the Waite Ackerman Montgomery property is that a concentrator was never constructed. In fact, the first ore to go through the Horne mill of Noranda Mines Ltd., built in 1928, was not from the famous upper H and L ore bodies but custom shipments from the Waite."

Jan 1, 1981

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

By Keith Eldridge, Robert Kelly

"Quality management has a/ways played an important role at the Iron Ore Company of Canada; particularly since the early eighties when the iron ore markets favoured buyers as opposed to sellers.Since thot time, IOC's quality system has evolved from basic quality control to the Deming philosophy and its 14 points, and on through various other phases to the ISO 9000 series.ISO 9002 Registration was' first requested by IDC's customers and development plans were prepared in 1988. At this time, Quality System Registration was unheard of in the mining sector and TDC found itself struggling with the concept. The 1U!Xt three years saw the company develop a Quality System to meet ISO 9002 in a two phased approach, setting new standards for the mining industry when registration was achieved in December 1991.The company now sees ISO Registration as the cornerstone of its future quality efforts. IOC's quality system has been integrated with several other initiatives such as loss control and functional training, both of which focus on training and management the workforce to do the job safely, the right way.This paper addresses the steps required to develop a quality system for the mining industry within the guidelines of the ISO 9000 Series and the subsequent integration of other quality related initiatives."

Jan 1, 1994

By T. A. Lazier, C. S. Longley

"Paymaster Consolidated Mines, Limited, owns several groups of claims in various parts of the Porcupine district. The area in which mining has been carried on includes parts of lots 5, 6, and 7, con. 1, Tisdale township, and twelve adjoining claims in Deloro township to the south. Highway No. 67A between South Porcupine and Timmins crosses the property.The discovery of the Dome mine in 1909 caused a rush of prospectors to the district and in a few weeks practically all territory adjacent to the Dome was staked. At that time work was started on the West Dome, West Dome Lake, Apex, and Standard properties. These were consolidated in 1930 to form the present Company. Gold was produced from the West Dome Lake from 1915 to 1930, and from the Standard-Paymaster from 1922 to 1928. The total production of the previous and present companies from 1915 to November 30, 1946, has been 487,170 oz. gold and 149,342 oz. silver from 2,337,554 tons of ore."

Jan 1, 1954

By B. Andreaus

In spite of tremendous efforts in research and development of polymer electrolyte fuel cells (PEFCs), essential properties of the actual catalyst material, supported Pt or Pt-alloy nanoparticles, are not yet well understood. Fundamental understanding of the catalyst structure and the prevailing kinetic mechanisms is, however, of utmost importance for further progress. In the present study, we investigate catalyst activity for CO oxidation from a theoretical point of view. Electrochemical CO oxidation serves as an important test reaction for the study of the fundamental properties of supported Pt nanoparticles. Recent experiments have revealed strong effects of catalyst particle size and supporting material on catalytic activity. It was found, that the activity towards CO oxidation decreases significantly when the particle diameter drops below 2.5 nm. We perform kinetic Monte Carlo simulations of CO oxidation on supported catalyst particles to elucidate this particle-size effect. The simulations are based on the active site concept, highlighting the role of active site formation and finite surface mobility of adsorbed electroactive species for catalyst activity. For comparison with experimental results, potential step experiments were simulated. The Monte Carlo simulations consistently reproduce effects of particle size and electrode potential found experimentally. In comparison with our simulations, analytical mean field models and nucleation and growth models exhibit inferior agreement with experimental data. In summary, our findings support an oxidation mechanism via active site formation. The reason for the slow reaction kinetics on catalyst particles with diameters below 2.5 nm is a rather low CO surface diffusivity. The rates of active site formation, diffusion and CO oxidation via recombination with adsorbed OH can be determined from the simulations.

Jan 1, 2005

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, A. M. Elmahdy, Keiko Sasaki

"Seawater has been reported to depress molybdenite in a copper-molybdenum (Cu-Mo) flotation process at high pH due to the precipitation of Mg(OH)2. Meanwhile, to improve mineral recoveries, collectors are usually added into the flotation cells, thus adding the complexity to the mechanism of bubble-particle interactions involved in Cu-Mo flotation. Therefore, understanding the interaction mechanism in seawater flotation and in the presence of collectors is important to explain the minerals depression. The present work investigated the effect of kerosene on the bubble collision and attachment to pure chalcopyrite and molybdenite surfaces in MgCl2 solution as one of the seawater major components at pH 6 and 11. Mineral surfaces were characterized using atomic force microscopy (AFM). In addition, minerals floatability in the same system were tested in a column flotation. The study of bubble-particle interactions shows that following several collisions, bubble could displace the intervening liquid layer on the mineral surfaces, forming a three-phase contact (TPC). A TPC formed more rapidly in the presence of emulsified kerosene in a 0.01 M MgCl2 solution at pH 6 for both minerals. The reason is kerosene increased the surfaces hydrophobicity and destabilized the intervening liquid layer on the surfaces. Moreover, the average time required to form a TPC was shorter on molybdenite surface. This can be attributed to the effect of adsorbed kerosene on molybdenite surface and molybdenite surface roughness.INTRODUCTIONIn froth flotation, bubbles are used to separate hydrophobic mineral particles from hydrophilic particles. In this process, bubble-particle interactions (i.e., collisions, attachment, and detachment) are crucial with regard to mineral recoveries. The effectiveness of froth flotation depends on the formation of stable aggregates between the hydrophobic particles and the bubbles, allowing the bubble to carry the particles to the froth layer. To form such aggregates, the bubbles and particles must collide, and the intervening liquid layer must be drained below the liquid layer critical thickness, forming a stable threephase contact (TPC) (Ralston & Dukhin, 1999). Particles detachment may take place if the particles still have sufficient kinetic energy and the TPC is not formed. Previous studies of bubble-particle interaction in electrolyte solutions have been conducted using atomic force microscopy (AFM) (Assemi, Nguyen, & Miller, 2008), and by approaching the bubble using mica plate (Pushkarova & Horn, 2008), however, these studies did not focus on the bubble-particle collisions. Bubble collisions and attachment to hydrophobic (Teflon) and hydrophilic (glass) surfaces in a a-terpineol solution have been investigated by Krasowka et al. (2003)."

Jan 1, 2016

By Agbo Chima

Low-lying sections of open-pit mines accumulate water, especially during the rainy seasons, preventing access to resource-bearing areas. To sustain mining operations, the water must be lifted out of the flooded pits at a high flow rate using pumps. These pumps need to be mobile so that they can be removed during drill-and-blast operations. Most mobile pumps rely on diesel engines with high maintenance requirements. A special pump design was developed to address the unique needs of open-pit mining while making the dewatering process more sustainable. Using the target flow rate and head data, an efficient pump was designed, encased, and deployed in the open pit. A variable speed drive (VSD) was installed in a protective skid so that the pump could be tuned to match the preferred flow rate at any point during its operation. This system was tied to the national electrical grid instead of being powered by diesel pumps, which reduced the carbon intensity per kilowatt-hour. The high availability, low maintenance requirement, and greater reliability reduced the use of spare parts, the fuel consumption, and the logistics associated with operating the pump. This further reduced the carbon footprint of the dewatering process. This paper provides some of the two-year performance metrics for a deployment in West Africa. With a focus on availability, maintenance costs, average cost per volume lifted, and carbon footprint, this encased pump system is compared to the diesel-driven pumps that it aims to replace.

Jan 1, 2023

Caterpillar Inc The world's largest manufacturer of construction and mining equipment, diesel and natural gas engines and industrial gas turbines. Technology leader in logistics, construction, transportation, mining, forestry, energy and electric power generation.

Aug 1, 2013

In-Country Business Development Agenda ?Siting/Permitting/Operational Planning ?Securing, maintaining, enhancing social license to operate ?Biodiversity conservation and ecosystem services ?IFC Performance Standards ?Environmental, Social, Risk Governance (ESG) ?Climate change plan

Aug 1, 2013

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By M. B. Greyver

The results of laboratory tests on iron precipitation from non-decopperized nickel anolyte are discussed. The parameters (pH, oxygen consumption and stirring speed) for iron precipitation from the anolyte, using the oxygen in the air, were determined. In the experiments conducted under optimized conditions, the residual concentration of iron in the anolyte after precipitation was 0.7-2.7 mg/L, and the copper and nickel losses to the solid phase were 0.05-0.07% and 0.05-0.16%, respectively. The filtration ability of the iron slurry obtained was 2 to 5 times higher as compared to that after chlorine oxidation and oxyhydrolysis. The leaching of the non-ferrous metals from the iron cake made using the separate nickel anolyte purification process was possible by dissolution in sulphuric acid. It was established that after cobalt precipitation from the copper- and iron-depleted anolyte, the precipitates obtained had lower ratios of Fe:Co and Ni:Co.

Jan 1, 2006

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2004

By J. Bhattacharya, S. K. Mukhopadhyay, S. K. Pal

"While time and again many authors have categorically stressed the restoration of the environment, very little effort has been made in the mineral industry to develop the economy of environmental control. There are many abatement procedures that search a maze of variants. Among them pricing environmental damage seems to be more logical and easily implementable.IntroductionMining as an operation has a severe impact on the Earth's natural resources. While economical environment control is much sought after, solutions are often varied and complex, and can differ in the problems of single or multiple mine sites.Determination of Optimum use LevelsIn “mining environmental control"" it is required to strike a balance to find optimum use levels. The solution is to find where the welfare benefits equal the cost involved to curb the degree of environmental damage (Fig . I) . In the mining industries this can be done by modifying the production/extraction process itself. For most pollutants, the marginal costs of control will exceed the benefits from further reduction of damage long before the zero pollution damage point is reached (Fig. I). From an economic perspective the optimal alteration of environment by mining would occur at z; pollution continues to be caused by ""zy"" control units, but it would be inefficient to pursue the redemption efforts further because the marginal cost involved would exceed marginal welfare benefits."

Jan 1, 1992