Search Documents

By Phil Molloy

"In March, 1968, Skega Ruh her Liners were used to reline the shell of an 8' x 12' Allis Chalmers ball mill.This mill is used to regrind the cyanided pulp from 58i -200 mesh to 92% -200 mesh prior to this pulp passing to the flotation circuit, at approximately 450 tons per day.Before the use of rubber liners, the regrind ball Mill shell had been lined with single wave ni-hard liner!'. These liners had an average life of five years. Ni-hard end liners were used both prior to and during the use of rubber liners, as the life of the ni-hard end liners was about seven years, and it was thus felt that little economic benefit would be realized by lining the ball mill ends with rubber.The rubber lining used has a thickness of 57.15 millimeters and the square shaped lifter bars which are spaced at 14~ inch centres, have a 4"" x 4"" cross-sectional dimension.With the use of ni-hard liners, the consumption of 1 1/4 forged steel balls averaged 1.062 pounds per ton, Using rubber liners the consumption of l~"" forged steel balls increased to 1.368 pounds per ton. Also the level of the ball load which previously had been kept at approximately 18 inches below the mill discharge, had to be increased to approximately 8 inches below the mill discharge in order to effect the same grind.The initial gri4ding performance of the newly relined mill was also poor, until the leading edge of the rubber lifter bars, which were square shaped in cross-section had been worn to a rounded profile. These lifter bars were replaced after 4 years and 3 months of operation.The advantages of rubber liners in our opinion is as follows:"

Jan 1, 1974

By T. Sun, J. Kou, C. Sun, China Railway Resources Group Limited

"The polymetallic sulfide ore in Jiama county of Tibet contains 0.78% Cu, 0.046% Mo, 0.31 g/t Au and 17.9 g/t Ag in average. However, heavy loss of valuable metals was observed using high-pH process and Butyl xanthate as the collector. In this paper, the flotation was optimized through the adoption of a novel collector C-7, which is a mixture of xanthate ester and thionocarbamate. This collector showed better flotation performance under weak base conditions. The recoveries of Cu, Mo, Au and Ag increased to 93.24%, 84.60%, 78.13% and 75.41%, respectively, under 15 g/t of C-7 at pH of 8.0. The adsorption mechanism of C-7 was investigated by micro-flotation tests, zeta potential measurements, FTIR analysis and adsorption quantity measurements. Chemisorption of C-7 on chalcopyrite surface is demonstrated with adsorption density 3.8 times higher than on pyrite.INTRODUCTIONXanthates are the most commonly used collectors of strong collecting ability for separating copper sulfide minerals from gangue in froth flotation. However, the selectivity of xanthates themselves is poor to realize separation of chalcopyrite and pyrite whose floatability are quite similar (Heyes & Trahar, 1977; Chandraprabha, Natarajan, & Modak, 2004). High pH process with xanthates as collectors is proved effective in copper-sulfur separation and is widely used in treatment of copper sulfide ore flotation (Smith, 1996; Valdivieso, Cervantes, Song, Cabrera, & Laskowski, 2004). This method could get ideal separation results, but large amount of lime must be added, and could bring about increased cost, device corrosion and environmental pollution. In addition, there could also be high depression and heavy loss of associated noble metal such as Mo, Au and Ag. Consequently, a large amount of research has been conducted on substitutions of xanthates for selective flotation of copper sulfide ores under low pH conditions (Gholivand, Khodadadian, & Ahmadi, 2010; Li, 2010)."

Jan 1, 2016

By G. Granata, C. Tokoro, M. Matsuoka, K. Horiuchi

"Given the high demand of copper and the lack of new high-grade deposits, low grade copper ores containing copper oxides and refractory sulfides need to be processed as well. However, in order to recover copper from refractory copper ores, the leaching performances should be improved. In this study, we investigated the effect of the mechanical activation in the leaching of copper from covellite. The influence of a mechanical treatment by planetary ball milling on leaching rate in sulfuric leaching media was evaluated by using X-ray diffraction (XRD), mineral liberation analysis (MLA) and X-ray absorption fine structure (XAFS). Results showed a significant increase in copper leaching from around 50%up to 100% along with an improvement of the leaching kinetics when using planetary ball milling. XRD spectra showed the disappearance of the covellite peak from (101) face, thus suggesting the amorphization of covellite associated with the use of planetary ball milling. XAFS results showed that the coordination number of Cu changed from 6 to 3, thereby confirming the effectiveness of the mechanochemical effect.INTRODUCTIONDuring the last decades, while the copper grade in copper ores has been decreasing, the concentration of impurities such as arsenic tends to increase, thus requiring for the processing of low grade copper ores. For a suitable processing of copper minerals, hydrometallurgical processes are preferable due to the lower costs, the lower environmental impact and the easier implementation (Watling, 2006). However, for an economical recovery of copper, the leaching performances must be improved.Among the recent advancements in leaching technologies, the mechanochemical activation allows for an improvement of the leaching performances by means of high-intensity grinding(Mohammadabad et al., 2016). In the first place, the improvement is the result of the dramatic decrease of particle size, which results in an increase of the mineral surface area and the consequent enhancement of leaching kinetics. Furthermore, the intense mechanical stress due to the high-intensity grinding could induce the rupture of the crystal structure producing a decrease of crystallinity. Such changes of the mineralogical structure, also known as mechanochemical effect, can lead to more leachable mineral, thereby resulting in a greater dissolution of copper. Last but not least, whereas the mineral surface might undergo passivation during leaching, the high-intensity grinding can continuously refresh the surface of the mineral, thus exposing portions of unleached bulk mineral."

Jan 1, 2017

By C. Prévost, V. Leclerc, R. Pinto, M. Ruel

"A buffer’s ability to dampen production variations is directly related to its size. Small buffers cannot handle large variations in production, resulting in production losses when their inventory is depleted or saturated. This paper presents a predictive control algorithm used to regulate the inventory in a buffer of limited size, subject to large production variations caused by an upstream batch process. The algorithm was designed to manage the acid flow rates in an acid regeneration process, servicing batch leach reactors at Rio Tinto Fer et Titane, in Sorel-Tracy, Québec. The objective was to increase production by reducing equipment downtime caused by imbalances in the acid tanks servicing the leach reactors. The controller attempts to maintain acceptable acid tank volumes by optimizing the leach reactors acid/slag ratio and reaction time as a function of anticipated acid needs, all while maintaining product quality.INTRODUCTION Some beneficiation processes in extractive metallurgy require processing bulk material in batches. Typical examples of metallurgical beneficiation batch processes are smelting, leaching, electrowinning, elution and carbon-in-pulp. These processes are often situated midstream in an ore beneficiation flow sheet and either receive or transfer ore to continuous processes. Batch processes, by their very nature, introduce large variability in the flow sheet, because they process large finite quantities of material at nearly periodic time intervals. In order to dampen variations in production, various buffers–tanks and stockpiles–are utilized to accumulate ore upstream and downstream of batch processes. A buffer’s ability to dampen production variations is directly related to its size (Phillis & Gumede, 2011). Small buffers cannot handle large production variations, resulting in equipment downtime when their inventory is depleted or saturated (Everett, 2010, Berton et al., 2013). Consequently, the batch equipment production rates must be adequately managed to minimize production losses, attributed to depleted or saturated inventories, while maintaining product quality. Algorithms that anticipate or predict future production variations are often utilized to regulate buffer inventories, subject to large flow rate variations (Salvo et al., 2002; Bonvin, 2013). This paper presents a predictive control algorithm used to maintain an acceptable volume in a spent acid tank servicing several batch leach reactors. The algorithm is implemented at the acid leach plant of Rio Tinto Fer et Titane, in Sorel-Tracy, Québec."

Jan 1, 2017

By Gary Walters, Matthew White, Thomas W. Gonzales

The copper smelting industry has transitioned into the 21st century compliant with environmental regulations, new smelter installations and brown field expansions. The industry faces new challenges as copper in concentrate grades have decreased while contained impurities have increased. A new benchmarking survey was undertaken to update the last survey of 2016 for operating copper smelters in the world. The information collected was separated based on primary smelting technology rather than by geographical location and supplemented from published literature. Each smelting technology’s unique use of specialized process equipment, concentrate smelting capacity, and impurity flexibility are discussed INTRODUCTION The 20th century was a remarkable time for the growth of copper smelting. Electric, blast and reverberator furnaces dominated the smelting technology well past WWII. In the 1970s, SO2 regulations and high energy cost drove the development of new primary smelting technology. Technological advancements decreased energy consumption and enriched sulfur dioxide concentrations of the process off-gas to levels where sulfur capture in sulfuric acid plants was economically viable. The new smelting technologies began to replace reverberatory and electric furnaces starting in the late 1940s. A new paradigm in copper smelting was established and the enabler was then Outkumpu’s® flash smelting technology from the 1940s through to today. Now, Outotec had become the dominant primary smelting technology with over 44 copper flash smelting furnace installations world-wide. Figure 1 shows the historical installation statistics of primary smelting technologies over the last 70 years (ICSG 2018). The dominance and acceptance of the Outotec® smelting technology from the 1940s to current can be seen. Isasmelt® technology for copper was introduced in the 1970s and did not see advancement in new installations until the 1990s through today. Isasmelt® has 12 world-wide copper furnace installations to date. Mitsubishi® also introduced continuous smelting and converting technology in the 1970s, but had no new installations until the 1990s with a total of 5 copper smelters. Outotec Ausmelt® smelting technology had 3 installations in the 1990s and totals 10 furnaces. Most recently the Chinese technology of Bottom Blown and Submerged Lance Smelting began commercial operations in 2005 for total installations of 11, mostly in China. Other technologies, such as, El Teniente, Noranda, Inco, and Vanyukov furnaces have contributed to the overall global smelting capacity, but have not penetrated the smelting industry to challenge the existing dominant smelting technologies. The technology distribution in Figure 1 also shows flash smelting technology for sulfide concentrate domination untill 2000, bottom blow technology has become the preference in China. Currently, China is the only country building new smelting capacity. Isasmelt® technology also seen a large increase in installations in the current decade.

Jan 1, 2019

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By G. Armand, A. Noiret, D. Seyedi, J. Morel

"Clay formations in their natural state exhibit very favorable confining conditions for repository of radioactive waste because they generally have a very low hydraulic conductivity, small molecular diffusion and significant retention capacity for radionuclides. Nevertheless, one concern regarding the hydromechanical behavior around drifts in such claystone is the associated pore pressure field disturbance during excavation works. In the short term, the very low permeability leads to an almost “undrained” condition, meaning that the stress change due to face advance will create volumetric strains leading to an increase or decrease of pore pressure. If the effective stresses reach the failure level, the induced damage around these excavations might change the favorable properties of such formations. To demonstrate the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW) in the Callovo-Oxfordian claystone (COX) formation, the French national radioactive waste management agency (Andra) started in 2000 to build the Meuse Haute-Marne underground research laboratory (M/HM URL). The present paper illustrates observed pore pressure changes during excavation of drifts (˜5 m diameter), of micro tunnels (˜0.7 m diameter) and a borehole (˜0.15 m diameter). All these openings are parallel to the major horizontal stress at the main level of the M/HM URL. In drifts parallel to the major stress (i.e., when the initial stress field in the drift section is quasi-isotropic) an important increase followed by a drop of pore pressure is observed in the horizontal plane at the drift wall. These observations emphasize the impact of the in situ stress state and rate of excavation on the pore pressure and provide important insight of the hydro mechanical behavior of the COX claystone and the relationship between pore pressure and excavation induced fractures zone."

Jan 1, 2015

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By Q. Shi, Q. Feng

"The influence mechanism of chlorite on the flotation of pyrrhotite was investigated through flotation tests, Zeta potential measurements, optical microscope photos, solution ion measurements and absorption measurements. It is observed that, the addition of chlorite influences the flotation of pyrrhotite seriously. The IEP (isoelectric point) of pyrrhotite and chlorite is 7.6 and 4.3 respectively, in the condition of slight alkalinity, both pyrrhotite and chlorite are negatively charged, and the hetero-aggregation will not occur. With the existence of oxygen in solution, the iron ions are dissolved from pyrrhotite surface because of the oxidation of pyrrhotite during pulp conditioning. The dissolved iron ions adsorb onto the surface of chlorite in the forms of iron hydroxyl and iron hydroxide, and the adsorption results in the opposite charge of chlorite surface. As a result, the hetero-aggregation between pyrrhotite and chlorite occurs. The adsorption of chlorite changes the surface property of pyrrhotite and restricts the adsorption of amyl xanthate onto pyrrhotite surface, and then decreases the flotability of pyrrhotite.INTRODUCTIONIn sulfide ores processing, magnesium silicate bearing gangue minerals often report to the concentrate causing downstream processing problems as well as increased smelting costs. Talc,chlorite and serpentine are gangue minerals commonly encountered in complex sulfide ores (Engel, Middlebrook, & Jameson, 1997; Pietrobon et al., 1997; Witney & Yan, 1997; Chen, Grano, Sobieraj, & Ralston, 1999a, 1999b; Bremmell, Fornasiero & Ralston, 2005; Senior & Thomas, 2005; Wang, Somasundaran, & Nagaraj, 2005; WieseHarris & Bradshaw, 2007). All of them are characterized with uniform crystal structures consisting of silicon-oxygen tetrahedron and magnesium-oxygen octahedron. The magnesium-oxygen octahedron layers are broken during the liberation of serpentine to expose the magnesium-oxygen bonds with strong ionicity and hydration, which results in natural hydrophilicity of serpentine. In water, the hydroxyl on serpentine surface ruptures and dissolves into the aqueous phase while the Mg2+ remains, resulting in surface positive charge (Tao, 2012). As serpentine has a positive potential at alkaline condition, it is therefore likely that it will attach through electrostatic attraction to the negatively charged mineral surface and reduce both the flotation rate and recovery of target minerals (Lu et al., 2011). For talc, characterized as good natural hydrophobicity, the liberation comes from the interlaminar fracture to remain molecular bonds on surface with weak hydration. Being naturally hydrophobic, talc easily reports to flotation concentrates, thus reducing concentrate grade (Shortridge, Harris, Bradshaw, & Koopal, 2000; Beattie, Huynh, Kaggwa, & Ralston, 2006). Meanwhile, both molecular bonds and magnesium-oxygen bonds are exposed on chlorite surface when liberation occurs, resulting in moderate natural hydrophobicity between serpentine and talc (Tao, 2012). And thus the mechanisms of influence of chlorite on sulfide ores are more difficult to study."

Jan 1, 2016

By B. McFadzean, I. Achaye, T. Chidzanira, J. Wiese

"Froth stability has an overriding effect on metallurgical recovery and grade for many ore types. Froth recoveries of less than 10% are common for low stability froths such as those in sparsely mineralized ores or in cells at the back end of flotation circuits. It is well known that, aside from chemical factors such as frothers and electrolytes, the mineral particles themselves have the dominant influence on froth stability. The particle properties of size and hydrophobicity are expected to have the greatest effects on froth stability. The aim of this study was to understand the effects of particle size on froth stability and to quantify these relationships.The study compared a synthetic ore of pyrite and quartz, with carefully controlled size ranges and hydrophobicity, with conventionally milled platinum-bearing UG2 ore and the bulk reverse flotation of hematite ore. A novel bench-scale continuous column flotation cell and continuous mechanical hybrid cell with large relative froth volumes, as well as a three-phase froth stability column were used to characterize the froths.It was found that froth stability could be related to the concentrate particle surface area by a Langmuir-type relationship. This is indicative that the mechanism by which particles stabilize the thin films in froths is similar to the mechanism by which surfactants lower surface tension. Different froth stabilities were found for different ores and this was thought to be the result of different particle sizes and distributions, which resulted in different packing densities in the thin films and Plateau borders. Interestingly, there was a clear relationship between the feed particle size and the froth stability even though froth stability was dependent on the concentrate particle surface area. It seems that the feed particle size is a good predictor of the surface area of particles in the concentrate. Concentrate particle size did not show a clear relationship with froth stability since it was already shown that it is both the size and the amount of the particles in the froth that contribute to the stability.INTRODUCTIONThe stability of the froth in froth flotation is important to the recovery and grade of the valuable mineral. Too stable a froth and the grade is reduced; not stable enough and the recovery may be compromised. Platinum-bearing ores with fragile, poorly mineralised froths are known to have froth recoveries that are routinely less than 10% (Crosbie et al, 2009). There are a number of chemical, physical and operating parameters that can affect froth stability, including reagent dosages, air flow rate, pulp density and particle properties. Arguably, the largest contribution to froth stability is from the particles that stabilise (or destabilise) the thin films in froths. Particle size, hydrophobicity and shape all affect froth stability to some extent."

Jan 1, 2016

By T. Boiselle, C. Gielen, P. Henry, J. M. Bier

"Hydrometal is specialized in the production of zinc sulphate from complex secondary raw materials. Electric Arc Furnace (EAF) dust is one of the more interesting potential sources to produce zinc sulphate. In order to minimize waste quantities generated from EAF dust treatment, our R&D team has developed and patented a new process to recover the Fe contained in the dust as iron oxide product to be used and sold into the pigment market. The process is based on a specific reductive leaching step of the zinc ferrite contained in EAF dust, followed by a purification step to remove impurities (Ni, Cr, Cu...) and finally the controlled precipitation of the iron oxide. The aim of the iron precipitation step is to obtain the right shape and length of crystals in order to guarantee the right color and tinting strength of the pigment. The innovative aspects of the process results in the controlled oxidation of the iron to get the right crystal size and good purity material. The iron product can be valorized as red or yellow pigment often produced by the Penniman-Zoph process.INTRODUCTION A Few Words about HYDROMETAL Hydrometal SA (Engis, Belgium) is a subsidiary of Jean Goldschmidt International SA (JGI) in Brussels. JGI is mainly involved in metal trading activities (Goldschmidt, 1995). In 1985, JGI acquired the leaching circuit of a Belgian electrolytic zinc producer located in Engis, a few kilometers south of Liège, near the river Meuse and it was decided to name this plant: SA HYDROMETAL. Hydrometal is well connected by water, rail and road from its central location in the industrial region of Liege, in the heart of Europe. The company received in 1997 an additional license to process and recycle toxic and hazardous waste. Figure 1 shows a picture of the plant."

Jan 1, 2016

"There are a number of disciplines in the minerals industry for which concern has been expressed regarding the sustainability of human capital. The boom-bust cycles that occur in the industry, the trend in tertiary education towards consolidation or in some cases cessation of minerals related programs and the increasing frequency of fly-in fly-out operations can all contribute towards a decline in the number of professionals with basic skills in process mineralogy. This paper describes approaches taken by the authors to incorporate process mineralogy into three levels of education, namely undergraduate, recent graduate and experienced professionals. The primary objective in designing the learning activities is the development of authentic learning experiences that provide participants with relevant skills in process mineralogy. Selected examples of approaches used by other education groups globally to address this issue are also provided.INTRODUCTIONThe boom and bust cycle of the mining industry has trickle down effects in tertiary education in terms of the ability of universities to consistently provide high quality graduates with relevant skills. When the commodity price surged in 2002 skills shortages in critical resource related professions were reported and despite investment in skill development there was a view from employers that not enough young people were graduating from relevant education programs (PricewaterhouseCoopers, 2012). At the time this signalled positive growth for engineering disciplines catering to the mining industry, however during the downturn cycles, most recently since 2012, graduates exiting from the discipline can find employment difficult and this contributes to reduced enrolments in subsequent years. From an AusIMM (Australasian Institute of Mining and Metallurgy) members’ employment survey conducted in 2013, more than half of the graduates exiting from disciplines related to mining and minerals were not confident of finding employment (AusIMM, 2013). In the long term the concern is not only how to sustain enrolment and graduate numbers but also to provide the opportunity for students to acquire the professional skills that they require to make them attractive to industry.Maintaining and sustaining core competencies in the minerals discipline is an ongoing challenge. There have been a number of recent papers on this issue presented at international conferences (e.g. McCaffrey et al, 2014; Drinkwater and Napier-Munn, 2014) and there is general agreement that one of the ways in which the deficit in foundation concepts can be addressed is through workplace development. Drinkwater and Napier-Munn (2014) presented data from a survey of industry professionals that indicated that more than 90% of respondents undertook on average 30 days of training each year of which approximately 5 days was professional short courses."

Jan 1, 2016

By Shantanu Patel, C. Derek Martin

"The objective of this work is to develop a practical numerical approach for applying the confining pressure to discrete element cylindrical triaxial tests. A layer of membrane particles with very low stiffness and extremely high contact bond strength was created around the lateral boundary of the cylindrical numerical specimen. To prevent the membrane particles from penetrating into the rock specimen on application of confining forces and to provide a smooth boundary surface, the space between the membrane and rock particles was filled using small-diameter packing particles. The results of this method were compared with those of rigid boundary method with confining pressure of 20MPa. The results obtained show that new approach gives both peak strength and post peak response that are in closer agreement with laboratory findings. BACKGROUNDThe discrete element method (DEM) has become the cornerstone for simulating both intact material and discrete fractures for low porosity strong rocks (ISRM Classes R3 to R6). Despite the advances in its application, simulating realistic behaviour of intact rock using the DEM remains a challenge. The bonded particle model was introduced as a potential solution for simulating the complex mineral grains in strong rock and other granular materials (Potyondy and Cundall, 2004; Utili and Nova, 2008; Salot et al., 2009). While some issues were resolved, a remaining challenge is the lack of the bonded particle model to simulate the brittle response commonly observed in strong rocks during the triaxial compressive test. Such behaviour is shown in Fig. 1 for Lac du Bonnet Granite at a confining pressure of 20MPa."

Jan 1, 2015

By Alireza Sarafi, Alijan Aftabi

"A hydrocyclic system used for mineral separation at the laboratory scale results in the separation of more than 90% of micas. The system functions only by water and might offer advantages where other methods of mica separation are not available. INTRODUCTIONVarious methods for the separation of micas, wollastonite, and garnet, e.g., screening, flotation, magnetic separation, and heavy liquids, are well known (e.g., Spence, 1929; Bates,I960; Gillson et al., 1960; Benjamin, 1971; Connor and Kolhnar, 1991; Collings and Andrews, 1991). However, where these methods are not available, the separation of micas by a hydrocyclic system developed by Sarafi and Aftabi (1991) may prove to be economic. This note is a brief description of the hydrocyclic system. Minerals and MethodFor testing the recovery of mica and other minerals from different rocks (garnet-mica schist, skarn, and pegmatite), standard minerals were tested first, and then rock samples. Pure mineral standards were prepared from coarse-grained samples of pegmatite, mica schist and skarn; the grain size of the minerals separated was more than I cm. The Hydrocyclic System and Mineral SeparationThe hydrocyclic system is shown schematically in Figure 1. In the first step in mineral separation, mineral and rock samples were crushed, milled, and then sieved to minus 250 plus 125 microns. Approximately 10 gm to 25 gm of the sample were inserted in decanter Dt • The motor pwnps, M1 and M2, were then turned on and the water valve rl was opened. At this time, water was flowing turbulently (30 em3/sec. to 50 em3/sec.) and minerals were separated according to their crystallographic nature, density and!or habit. The fInal separation was done by exit valves r2, r3 and r4, while the motor pwnps were still operating. After each experiment, the rt , r2' r3 and r4 valves were closed and the motor pumps were turned off. Following this, minerals in each decanter and the mter were collected, dried and weighed. The whole time of the experiment was optimized to be about 10 minutes, but varied from 3 to 15 minutes for micas and garnets. respectively."

Jan 1, 1994

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By Bergh. L. C.

On line monitoring and diagnosis systems of process operating performance are becoming an important part of industrial programs, leading to improve process operation and therefore product quality over time. In processes, such as the contact section of a sulphuric acid plant, a large number of input variables, highly correlated, are presented. These characteristics usually pose more difficulties in modelling the process for monitoring and diagnosis purposes. Multivariate statistical projection methods, such as Main Component Analysis, have been proposed to effectively deal with these situations. The application of these ideas to a section of a 2350 MTD sulphuric acid plant, located at the Caletones Smelter, including dry tower, gas blowers, catalytic reactor and S03 absorber processes, is discussed here. A PCA model with eight main components is used for monitoring and diagnosis of more than seventy operating variables. Hottelling's T2 and Q residuals test were used for detecting measurement problems in relevant variables, and for identifying which set of variables were responsible for driving the process outside its normal operating region. Furthermore, considerable information for the correction of the tested operating problems was given by the use of these techniques.

Jan 1, 2007

"Coupon testing has been used to investigate stress corrosion cracking (SCC) of rockbolts in a laboratory based experimental program. This program has focused on the use of ASTM G39 three- and four-point bent beam coupon specimens, immersed in an acidified sodium chloride test solution containing hydrogen sulfide. The specimens were loaded to a range of stresses from zero, to just above the materials yield strength. It was found that only specimens above an applied stress of 580MPa failed by means of SCC, showing that rockbolts loaded to near their yield strength may be susceptible to SCC in-situ.INTRODUCTIONStress corrosion cracking (SCC) is a failure mechanism that affects material through the growth of hairline cracks when exposed to a corrosive medium while under stress (Jones and Ricker, 1999). SCC has been found to affect rockbolts in the Australian underground coal mining industry and has the capacity to cause the catastrophic failure of ground support systems, potentially leading to falls of ground in underground excavations, injury or death to mine personnel, damage or loss of equipment, and loss of productivity through the loss of roadway access (Crosky et al, 2002).Coupon testing utilises small scale samples that are intended to be indicative of the behaviour exhibited by a material in-situ (ASTM G39). The small scale, and usually high surface area to volume ratio of coupon specimens mean that they corrode at faster rate proportional to their mass, greatly reducing testing times. The small scale of the specimens allows them to be more easily prepared and handled, loaning them to mass manufacturing techniques.A previous study conducted by Vandermaat et al (2012b) into the use of three- and four-point coupon testing in-situ in an underground coal mine failed to result in SCC of the specimens. This paper serves as a follow up laboratory investigation in order to understand why these specimens did not fail. Previous studies into the SCC in rockbolts carried out by Gamboa and Atrens (2003) determined that rockbolt steel has a critical stress threshold of approximately 90% of the material ultimate tensile strength (800-900MPa). This study will focus on this critical stress threshold as a possible explanation for the lack of failure in the in-situ specimens (Vandermaat, 2012b)."

Jan 1, 2015

By B. McFadzean, J. Taguta

In order to recover minerals by flotation, the sub-processes of collector adsorption onto the valuable minerals followed by bubble-particle attachment should occur efficiently. This paper investigates both of these sub-processes for various thiol collectors and their mixtures onto base metal sulfide minerals. The aim of the work was to investigate whether there is a correlation between the strength of the collector interaction with the mineral and the subsequent bubble-particle attachment. The collector-mineral affinity was measured experimentally using an isothermal titration calorimeter in order to determine the molar enthalpy of adsorption for each collector-mineral system. The bubble-particle attachment was measured using a microflotation device which essentially determines the hydrophobicity of the mineral. Sodium ethyl xanthate (SEX) and sodium diethyl dithiocarbamate (DTC) and mixtures thereof were used as collectors with either single minerals or binary mixtures of pyrite and chalcopyrite, respectively. The adsorption enthalpies of the collectors were interpreted with reference to the chemical structure of the collector molecule and showed that the greater the positive inductive effect of the collector, which may be qualitatively related to their pKa, the greater their affinity for the mineral surface. In the microflotation studies, recoveries were strongly related to the alkyl chain length but there was no correlation between the enthalpies of adsorption and the flotation recoveries. When mixtures of collectors were used there was clear evidence of synergistic effects and in the case of DTC/xanthate mixtures it is possible that this synergism is related to a DTC promoted oxidation of xanthate to dixanthogen. When mixtures of pyrite and chalcopyrite were used the flotation recovery and enthalpy of adsorption of SEX onto the individual pyrite particles in the mixture increased substantially compared to the case of pyrite alone. Mechanisms are proposed to interpret these important observations.

Jan 1, 2016

By A. Makinen

There is an increasing trend between increasing consumption of water and the production of metal concentrate. Along with this trend we see that ore grades are declining and getting more complex to concentrate around the world. This will not only complicate processing but also generate new requirements for the management of water and waste streams on mining sites. The mining industry is a large user of water and its water consumption is growing rapidly. The processing of lower quality ores requires greater volumes of water. For these reasons, the need for efficient use of water and water management at mine sites is becoming more urgent. The perception of water in the mining industry has changed from thinking about it only in terms of "water treatment" to actually seeing it as a valuable resource, a resource that needs proper management. This resource management needs to involve various aspects, such as optimizing water usage of the entire mine or concentrator site, minimizing fresh water usage, minimizing or eliminating waste generated in water treatment and implementing practices for water reuse and water recycling. This paper presents trends and new developments relating to waste and water management in the mining industry.

Jan 1, 2015

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015