Search Documents

By Douglas Lay

Attention has been drawn in the publications of the Department of Mines to the view that veins of two different ages occur in the Cariboo district, namely, those of Jura-Cretaceous age and those of pre" Mississippian age. It has been further pointed out that while there is doubtless a wide distribution of veins of pre-Mississippian age in and about the Barkerville and Stanley areas, and in the vicinity of Round Top mountain and Yank's peak, there is no such wide distribution of veins carrying gold values of commercial significance. Veins of the latter type discovered to date occur almost exclusively within one or other of two comparatively narrow zones, both trending northwest and southeast, the one extending from Island mountain co Round Top mountain, and the other from a point somewhat north of Stanley co Yank's peak. In addition, there is some evidence of a third zone trending northwest from Spanish mountain, at or near the contact of the pre-Cambrian and Mesozoic rocks. In short, all the evidence from prospecting and lode-mining operations to date indicates that values are mainly restricted co zones having marked directional distribution. Moreover, it can be demonstrated that the placer deposits resulting from the erosion of the pre-Mississippian veins have a similar directional distribution, allowance being made for modifications due to glaciation. The observations offered in this paper are of the nature of a generalization which seeks to explain certain anomalies both in the vein-mineralization and in the -important auriferous-pyrite replacement deposits in limestone which have recently been discovered. For the sake of brevity, the Island Mountain-Round Top Mountain zone will be referred to as Zone No. 1, and the Stanley-Yank's Peak zone as Zone No. 2.

Jan 1, 1936

By Roger J. Goodman

"Major industrial restructuring, which started to manifest itself in the mature economies of the Western World and Japan in the 1970s, will accelerate in the 1980s and 1990s. Conventional heavy manufacturing industries will continue to lose ground to lighter processing/assembly operations and the new wave of high technology, information and service sectors. The decline in heavy manufacturing has severely impacted on the steel industries of Western Europe, the U.S.A . and Japan.World trade in metallurgical coal has shifted correspondingly, with declining demand in the mature developed countries being only partially offset by large increases in the steel intensity of the newly-industrialized countries (NICs) of the Far East, Latin America and, to a more limited extent, the Middle East and Africa. These trends will be accentuated in future years with direct implications for the distribution of metallurgical coal trade. This paper discusses, in quantitative terms, such changes in the 1980s and 1990s, and examines the implications for, and impacts on, Canadian metallurgical coal exporters.IntroductionThe twenty-year period from the early 1950 s to the early 1970s was characterized by inexorable growth in consumer demand and industrial expansion in most of the advanced countries of the western world. Long- term forecasting during this period typically used linear extrapolation techniques which , despite their simplicity, invariably ended up predicting future demand and production level s with uncanny accuracy. Times have changed!The last decade has been characterized by a n abysmal failure of our economies to respond to simple long-term, linear growth patterns. We appear to have entered a new world in transition, where we can observe a wave of dying or sunset industries reluctantly being submerged by a wave of emerging or sunrise industries.This paper is aimed a t examining the evidence for long-term industrial restructuring trend s. For want of a better word, these so -called, megatrends are then used to predict future demand level s and spatial distribution of steel development and , hence, metallurgical coal trade. It is tempting to correlate the decline in economic activity in the western world with the first Organization of Petroleum Exporting Countries' (OPEC) crisis of 1973. This crisis was probably no more than the straw that broke the camel's back, as the megatrends and embryo s of major industrial restructuring were already evident. Today these megatrends are merely more apparent and transparent than they were ten years ago.While the concept of industrial restructuring is the new economic buzz word, the process was at work, to a lesser degree even throughout the period of strong economic growth of the post-Second World War boom. Many people still remain convinced that our present-day sluggish economy is just part o f the typical , though rather more prolonged, recessionary cycle. Yet, we have always been part of a dynamic economic system and industry throughout history has been the subject of a continuous process of evolution, restructuring and reconstitution . Now the time is ripe to examine the evidence for such restructuring in order to develop coherent policies of adjustment in this transition from one industrial regime to another."

Jan 1, 1985

By D. Saramak, T. Gawenda, Z. Naziemiec, A. Saramak

"Crushing and grinding operations are burdensome to the environment due to generating large amounts of dust, noise and waste during course of comminution operations. An indirect negative contribution of industrial crushing processes is an increase of carbon dioxide emissions, which is a byproduct in energy production processes. On the other hand comminution processes in ore enrichment technology are essential due to liberation the useful minerals from the gangue, and producing the demanded particle size fractions of products. The article concerns investigation over negative influence of comminution devices on environment in terms of dust and noise emissions. Several various crushing devices were under investigations, both in laboratory and in industrial scale.The obtained results were analyzed in terms throughput and energy consumption achieved in various crushing devices. The test results allow to conclude that an intensity of dust generation for individual types of crushing devices is varied. An additional aim of this article is to link the aspect of mineral processing with its environmental impact and hence an influence of raw materials beneficiation industry on the quality of life of residents in immediate and close vicinity.INTRODUCTIONMineral raw materials beneficiation processes are an integral part of multi-stage processing of coal, iron ore and non-ferrous metals, production of aggregates, cement, or precious metals and stones. One of the common features of all beneficiation operations is their high energy consumption, which is mainly connected with various operations of feed particle size reduction. Comminution processes in ore enrichment technology are essential to expose and liberate the useful minerals from the gangue, while in aggregate production processes – to obtain the demanded particle size fractions of products. Crushing operations are characterized by a high degree of negative impact to the environment and humans, mainly due to:• High electricity consumption, which indirectly contributes to the increased emissions of carbon dioxide into the atmosphere, since CO2 is often one of the byproducts of energy production;• Relatively rapid wear of device working parts, what forces a production of spare parts and involvement of steel industry;• Intense dust pollution generated during crushing and grinding processes. This is one of the factors affecting the air quality and the consequent deterioration of the living conditions of inhabitants near mines and processing plants; and • Excessive noise emissions."

Jan 1, 2016

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By Robert D. Brown, Robert B. Parsons

"Careful tax planning and proper attention to the regulations can result in an optimum deduction ""of the 25% federal resource allowance. Introduced in the Income Tax Act in1976, in part to compensate for the disallowance of provincial mining taxes and royalties. the 25% ""resource allowance"" is a permitted deduction in computing taxable income from mining and petroleum. However, the rules relating to the deduction are complex, and the importance of the deduction which can readily exceed 25% of net income- is frequently underestimated. This month, Tax Notes discusses the basic rules of calculating the resource allowance, and suggests some tax planning aspects which may warrant consideration.May 6, 1974 - "" .. . our provinces have adjusted royalties, mining taxes and other arrangements to derive what they perceive to be a fair share for the benefit of their people. However, a provincial resource is also a national resource... I am proposing that revenues derived by provincial governments in respect of production from a… mineral resource should no longer be.\ deductible in computing the income of the operator. .. I am proposing that. .. there be an extra abatement from federal income tax in respect of taxable production income.. .fifteen points in the case of mineral profits. .. "" - The Honourable John N. Turner, Minister of Finance. June 23, 1975-"" &apos;"" to meet, at least in part, the request for some form of deductibility in the tax system for provincial resource levies... to offer more incentive to those who explore and develop in Canada. .. I am now proposing, the extra fifteen point abatement of federal taxes would be withdrawn... at the same time, I am introducing a new resource allowance, which would be an extra deduction from income equal to 250/0 of production income.. ."" - The Honourable John N. Turner, Minister of Finance."

Jan 1, 1980

By T. Hadley, Northern Minerals Ltd, C. S. Griffith, T. A. Safinski, K. H. Soldenhoff, M. Fainerman-Melnikova, A. Manis

"ANSTO Minerals and Northern Minerals have been working together since 2012 on the process flowsheet development for the Browns Range project for the recovery of the heavy rare earths (Dy – Lu, + Y). Initial efforts were directed toward defining the most efficient and direct flowsheet for the Preliminary Feasibility Study (PFS), issued in June 2014, then towards the Definitive Feasibility Study (DFS), issued in February 2015. These goals were achieved by undertaking comprehensive laboratory and continuous piloting programs. Further improvements to the flowsheet following the DFS have been made. This publication provides an overview of the evolution of the process flowsheet based on these laboratory and piloting programs from the PFS through the DFS and beyond.INTRODUCTIONNorthern Minerals Ltd (Northern) has been working on developing their flagship project at Browns Range for the recovery of the heavy rare earth elements (HRE, Dy – Lu, + Y). The project is located in the north of Western Australia as shown in Figure 1. The Total Mineral Resource at the project is currently estimated at 8.98 Mt @ 0.63% total rare earth oxides (TREO) comprising 56,663 t of contained TREO using a cut-off grade of 0.15% TREO. Of the Total Mineral Resource, 58% is classified as Indicated Resource, with the remainder in the Inferred Resource category.The deposit is characterised by breccia-hosted, hydrothermal, HRE-rich, xenotime mineralisation. The main gangue mineral associated with the xenotime is quartz. The distribution of rare earths (RE) observed for the xenotime mineralisation at Browns Range is presented in Figure 2. Extensive test work has shown that the xenotime can be readily beneficiated to between 20 – 40% rare earth oxide (REO) using a process consisting of crushing and grinding, followed by magnetic separation and flotation steps. Continuous piloting of this process was conducted on ~80 t of trench-sourced ore in late 2013 at SGS Perth, to produce ~2 t of ~20% REO mineral concentrate (MC) for hydrometallurgical testing. The composition of the MC produced during piloting is presented in Table 1."

Jan 1, 2016

By Lionel C. Kilburn

"This geological engineering method is based on jour main characteristics of mineral properties, viz; location: inclusion of valuable mineralization; inclusion of geophysical and/or geochemical targets; and inclusion of geological targets. These are subdivided into a total of 19 subcategories, which are used to determine the value of the property.The nineteen subcategories are prioritized and assigned relative value factors from 1.3 to 10. Value of each mineral claim unit is determined by applying the appropriate subcategory factors to a base value of $400per 16.2 hectare unit. Property value is calculated by totalling the values of such individual claim-units.The boundary between ore grade and sub-ore grade must be estimated for each property under valuation, thereby making the method sensitive to mineral commodity prices.A clear and disciplined sequence of decisions based on personal experience forms the basis of this method. The method utilizes all factors normally used to value a mineral property.IntroductionIt is generally accepted in the exploration industry that valuation of exploration properties is a subjective rather than objective process (Roscoe, 1986; Lawrence, 1988; Lawrence, 1989; Woodcock, 1985), and that it is greatly influenced by the experience and qualifications of the person who is doing the valuation. However, the significantly low degree of objectivity in mineral property valuation at this point in time invites effort to achieve a more quantitative engineering basis.Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand , and political-economic conditions, all of which vary with time. Therefore, any valuation is valid for only that point in time when it is made. Mineral deposits can decrease as well as increase in technical value with time."

Jan 1, 1990

By S. Caron, M. Bourassa, J. Châteauneuf, L. Tardif

"Since many years, the Yvan-Vézina gold plant custom mills and processes different ore types that show different behaviors. Because of this, cyanidation control is more complex than for a typical milling operation. In 1992, a Cyancor™ on-line « free cyanide » analyzer has been installed for monitoring and optimizing cyanidation. This implementation significantly reduced cyanide consumption for the overall cyanidation process. In order to further reduce cyanide costs, an automatic control strategy has been implemented to decrease fluctuations of« free cyanide » from their set points.This paper outlines the major steps of the project: process control audit, control strategy development, implementation and running-in period. Control strategy features include data filtering modules, adaptive PID algorithm and set points management modules are also presented. Finally, the strategy efficiency is illustrated with load-disturbance responses.IntroductionLocated in northwestern Quebec, the Yvan-Vézina plant has an average capacity of 1300 t/d using carbon-in-pulp technology. In 1991, the Yvan-Vézina gold plant was processing three types of ores (Beauchemin, Mouska and Silidor mines) and a pyrite concentrate (Beliveau mine). A cyanide reduction program was then undertaken to reduce « free cyanide» fluctuations <6>. To reach this objective, the optimum cyanide concentration was determined for each ore, a continuous monitoring method with the Cyancor™ on-line analyzer was developed and a tighter control of cyanide addition was applied. These modifications to the leaching practice significantly reduced cyanide consumption.After a while, it was observed that regulation of « free cyanide » concentrations could still be improved by the use of an automatic control strategy. Yvan-Vézina and CRM began collaborating in 1995 to develop and implement such a strategy. Results show that main disturbances of the circuit (e.g. ore mineralogy and pulp feed rate) can be significantly overcome in order to reduce their effects on the leaching operation."

Jan 1, 1998

By P. I. Laforest, M. S. Moats

"Antimony in smelted copper anodes has been shown to cause problems in electrorefining including brittleness of starter sheets. In order to improve deposit properties, a study was conducted examining the effect of anode chemistry on cathode ductility and electrolyte chemistry. Two industrial anodes with different molar ratios of As/(Sb+Bi) were used in laboratory electrorefining experiments with commercial electrolyte, and the addition of commercial glue and Avitone. The ductility of 21-hr copper deposits was evaluated by a 180° bend test. X-ray diffraction (XRD) and metallography were performed on unbent specimens to characterize the deposit structure. Increasing the anode As/(Sb+Bi) molar ratio from 0.54 to 3.8 resulted in an increase, on average, from four to eight bends to failure in cathode material produced. Significantly lower concentration of antimony (V) in the electrolyte was detected when operating with the higher molar ratio anode. The presence of (111) and (200) planes was noted in cathode material produced from the higher molar ratio anode suggesting that mixed growth character could be responsible for the observed increase in bend test results. The ductility of the starter sheet materials was improved by a higher anode molar ratio.INTRODUCTIONThe presence of antimony in copper electrorefining electrolyte has been reported to cause problems in cathode production (Hiskey, 2012; Peng, Zheng & Chen, 2012; Wang, Chen, Zhou-Lan & Lian-Sheng, 2006; Wang, Chen, Zhou-Lan, Wang, Xiao & Zhang, 2010; Wang, Chen, Zhou-Lan, Wang, Xiao & Tang, 2011; Wesstrom, 2014). To better understand the impact of antimony, laboratory scale electrorefining experiments were conducted using industrial inputs (anodes, cathodes and electrolyte). The influences of anode chemistry on the valences of antimony and arsenic in the electrolyte were monitored and correlated to physical cathode characteristics, such as a bend test to failure and crystallographic orientation.Commercially, starter sheets are produced by electrorefining impure cast copper anodes onto titanium blanks. The starter sheets are then hung in an electrorefining or electrowinning cell using loops of bent starter sheet material. These loops, in the absence of sufficient ductility, fail resulting in cathodes falling into the electrolysis cells. It is thought that the reduction in ductility can be related to anode composition; in particular, the molar ratio of arsenic to antimony plus bismuth As/(Sb+Bi). It has been stated that maintaining this ratio above 2:1 results in numerous improvements to electrorefining operations (Baltazar, Claessens & Thiriar, 1987; Kamath, Mitra, Radhakrishnan & Shetty, 2003; Krusmark, Young & Faro, 1995; Noguchi, Itoh & Nakamura, 1995; Wenzl, 2008)."

Jan 1, 2016

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By O. Hall

DISCUSSION AT QUEBEC MEETING MR. A. V. CORLETT: With drill holes radiating from a common point, is loading carried to the collars, and do you undertake to distribute the powder evenly? MR. R. V. PORRITT: When the collars of the holes, particularly the diamond-drill holes, are close together, two out of three holes are loaded only to within six or seven feet of the collars, and the intervening holes are loaded close to the collars. When the collars are farther apart, the holes are loaded close to the collars. No spacers are used, and the holes are filled solid with powder, this applying particularly to the diamond-drill holes, except, of course, where the collars are close together and some holes are not loaded close to the collars. MR. J. G. L. McCREA: I would like to enquire in respect to the various efforts made to reduce the cost of diamond drilling to the lowest point, what is. the relative cost of the solid bit to the standard bit? It would seem that the solid bit has the higher cost. MR. PORRITT: The non-coring or solid bit gives a slightly lower diamond cost than the coring bit. With the coring bit, the greatest diamond loss is on the inside stones, apparently due partly to vibration, but mainly to the core blocking against these stones. This condition, of course, does not apply with the non-coring bit. Our experience is that the non-coring bit, which drills out a much greater area, has a diamond consumption slightly less than the coring bit. The non-coring bit is sturdier, and is far less liable to damage in starting holes and in drilling through cracked or broken ground.

Jan 1, 1939

By J. Dupre, A. Gontcharov, H. Pepin

Produced by the conventional TIG welding CMSX-4 welds had been studied. It was demostrated that microstructure of welds depended on filler materials, welding parameters and joint design. Epitaxial solidification of CMSX-4 clad deposits produced a directionally solidified structure while welding with the similar filler material. Defects free clad welds were obtained by TIG welding without preheating using similar and dissimilar filler materials.

Jan 1, 2006

By Behzad Vaziri Hassas, Firat Karakas, Esra Tanisali, Mehmet S. Çelik, Ahmad Hassanzadeh

Coagulation is basically an aggregation process where particles settle under the influence of interfacial forces with electrostatic forces playing a governing role. Although particle morphology consisting of shape and roughness dictates the physical encounter of two particles, their eventual coagulation is not only influenced by columbic forces but also other interfacial forces such as hydrophobic interaction, which affects the extent of aggregation of particles through increasing the distance of interaction. Roughness is well known to increase the effective contact angle on hydrophobic surfaces and also enhance interfacial forces. In this study, the effect of morphology of particles and particularly roughness on the settling velocity and in turn coagulation tendency was investigated. Batch settling tests (BSTs) of different particle morphologies were investigated as a function of pH. Two different morphologies of silica particles were utilized with the same particle size distribution (PSD) including smooth-spherical and rough-spherical (Etched). Rough particles were prepared by acid etching technique using hydrofluoric (HF) at different time intervals (15-300 sec). Etched samples were identified and quantified by optic profilometry. Settling test results showed that the settling velocity of particles in a suspension of 2% solids in the massive settling region is significantly affected by particle morphology of the suspension. Coagulation results further revealed that aggregation of rough particles is faster than smooth-spherical particles. Coagulation results are elucidated on the basis of particle morphology and its effect on distance of separation through hydrophobic forces.

Jan 1, 2016

By W. Evans, T. Steis

"Sulphide ores under certain circumstances will react with explosives to generate an autocatalytic chemical reaction. This reaction is exothermic and results in the production of large volumes of poisonous gases and creates an unsafe, unstable condition with the possibility of a low energy deflagration or even a detonation of the loaded hole. This paper outlines the conditions that need to exist for such a reaction to take place and the precautions necessary to minimize or eliminate the problem in areas of reactive ore. A special case study involving a northern Ontario mine will be detailed.IntroductionOne of North America&apos;s leading underground gold producer&apos;s processes over 6500 tonnes of ore per day from an orebody containing high concentrations of sulphides. After six years of problem free operation, the mine experienced two serious reactions in two months between the sulphides and AMEX II, the ammonium nitrate and fuel oil explosive it uses."

Jan 1, 1995

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By T. Grammatikopoulos, A. Jordens, C. Gunning

"Exploration activity for rare earth element (REE) deposits (i.e., alkaline complexes, carbonatites) has increased significantly in the last decade. A number of deposits have been evaluated around the globe. However, new mines have not been commenced in the last few years with the exception of Mount Weld (Lynas) and Mountain Pass (Molycorp).Resource estimation of REE can follow similar guidelines to other metal projects. However, the inherent mineralogical characteristics of the REE deposits, despite their complex nature, have been generally overlooked by many exploration companies. These include variability of the ore, liberation and association of the REE minerals, and grain size, all of which can affect the processing of the ore. Each deposit appears to be different in terms of matrix and REM (rare earth minerals). Light REE bearing minerals such as allanite, monazite, bastnaesite, synchysite, and HREE bearing minerals such as fergusonite and xenotime can vary widely in composition, grain size and association (e.g., carbonates or hard silicates). On the other hand, although not really REM, zircon, Zr-silicates, titanite, fluorite, apatite, and in some cases many other common silicate minerals can carry trace to significant concentrations of REE.The evaluation of REE deposits should include an appropriate mineralogical characterization in order to quantify the REM, distribution, liberation and association by quantitative mineralogical techniques (i.e., QEMSCAN, MLA, TIMA and others); chemistry of the REM by electron probe micro analysis (EPMA), Laser Ablation ICP-MS or ToF SIMS.These techniques provide valuable data for geological purposes such as: defining quantitatively, the variability and distribution of the REM; differentiating between LREE and HREE zones to delineate ore; and metallurgical purposes to predict minerals/REE behaviour during processing. The lack of a comprehensive mineralogical characterization often leads to the wrong processing path and ultimately affects the elemental/mineral recovery."

Jan 1, 2016

By Robert B. Parsons

"The February 18, 1987, Federal Budget contains a proposed amendment which would simplify somewhat the ""successor corporation"" rules in the Income Tax Act. Despite this amendment, though, the important successor rules will continue to be relatively complex.IntroductionThe February 18, 1987, Federal Budget papers propose an income tax amendment whereby the so-called ""successor corporation"" rules would be revised by removing the present provision which limits the application of these rules to a maximum of two ""successions"". The successor corporation rules represent one of the most complicated sets of rules in the Income Tax Act. This month, Tax Notes seeks to explain these rules and the proposed amendment in simplified terms.Basically, the successor rules provide a mechanism for transferring unused exploration and development expenses from one taxpayer to another , in specified circumstances. The aforementioned limitation of two successions refers to the rule which allows a maximum of two such transfers with respect to any particular pool of deductions."

Jan 1, 1987

By Lawrence Devon Smith

What is a Failed Project? For mining projects, some key indicators of a ?failed? project are: ? Cost is more than it should be (particularly capital) ? Schedule ? It takes longer to build than expected ? It takes longer to ramp-up than expected ? It does not do what it is supposed to do ? Poor performance; output, product specifications; ? Low revenue ? High costs ? No one is happy about it: Management, Shareholders, Bankers ? Does a project fail if it does not meet expectations that were unrealistic and unattainable? ? Caution: Failure may not become evident until years later

May 1, 2010

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995