Search Documents

By S. Esfahani, M. Barati

Heat recovery from blast furnace slags is often contradicted by another requirement, to generate amorphous slag for its use in cement production. As both the rate and extent of heat recovery and slag structure are determined by its cooling rate, a relation between the crystallization kinetics and the cooling conditions is highly desired. In this study, slags with different basicities were studied during non-isothermal cooling. Their continuous cooling transformation (CCT) diagram were plotted and compared with each other. Then, a mathematical model was developed that predicts the amount of crystallization during cooling. The results were validated by experiments performed by Single Hot Thermocouple Technique and image analysis. A second mathematical model that calculates temperature history of slag during its cooling was coupled with the above model, to allow optimizing the slag/air ratio for both heat recovery and slag glass content.

Jan 1, 2015

By Qing-Xun Low

Ni current collector has excellent electronic conductivity and mechanica, properties. However, nicke, cannot be used in H2S-containing syngas SOFCs due to sulfur poisoning and coking. Copper coated nicke, is prepared by electrochemica, deposition. XRD, SEM, and EDX techniques are used to characterize the samples. After high temperature treatment in syngas containing, the coated samples exhibit high resistance of coke formation and sulfur corrosion compared to pure nickel. Therefore, copper coated nicke, is a promising anode current collector for H2S-containing syngas SOFCs.

Jan 1, 2010

By L. E. Young

"The Red Dog deposit of the western Brooks Range, Alaska was discovered in the 1970s. Two mineralized areas are present, the Main and Hilltop deposits. With indicated and inferred reserves of 77 million tonnes of 17.1% zinc, 5.0% lead and 82 g/ tonne silver, the Main deposit of Red Dog represents one of the world's largest zinc-lead deposit s. Since serious evaluation by Cominco commenced in 1980, a better understanding of deposit geology has been gained through 10 715m of diamond drilling and concurrent geologic, geophysical and geotechnical studies. The Red Dog deposit is of Mississippian to Pennsylvanian or Early Permian age, and straddles a redox transition in fine-grained and chemical sediments of the Red Dog structural sequence.The Main deposit has been modified by regional Mesozoic thrust faulting and isoclinal folding, resulting in complex interrelationships between silica rock, sulphide rock and barite. Multiple lines of evidence suggest the Main deposit contains both a syngenetic stratiform and a replacement component. Ore fluids were probably derived by regional lateral movement of brines through a coarse clastic footwall aquifer, then upwards along block faults to the site of the Red Dog deposit.Historical PerspectiveThe region in the vicinity of the Red Dog deposit (Fig. 1) was first prospected by J. W. Kelley in the late 1880s (Orth, 1967). The first coordinated inland exploration was conducted by the U.S. Geological Survey in 1910-1911 and 1923-1926 (Smith, 1913; Smith and Mertie, 1930). The earliest reports of zinc-lead mineralization in the region include reference to samples collected at unknown locales by Eskimo prospectors (Anderson, 1944). In 1955 stratiform pyrite was discovered 19 km west of Red Dog by I.L. Tailleur of the U.S. Geological Survey (Tailleur, 1970). The first reported visit to what is known as Red Dog was by I.L. Tailleur in 1968, who was field checking a colour anomaly noted by B. Baker, a local bush pilot (Tailleur, 1970; Moore et al., 1986) ."

Jan 1, 1989

By L. Nastac, Y. Xuan

"The metal-matrix-nano-composite (MMNCs) in this research work consists of an A356 alloy matrix reinforced with 1.0 wt. % SiC 50 nm diameter nanoparticles that can be dispersed within the molten alloy matrix via ultrasonic stirring technology (UST) and induction melting and stirring processing. The necessary ultrasonic parameters to achieve the essential cavitation for adequate degassing and refining of the A356 alloy as well as the optimum fluid flow characteristics for uniform dispersion of the nanoparticles into the A356 alloy matrix have been investigated in this study by using computational fluid dynamics (CFD) modeling with a magneto-hydro-dynamics (MHD) model and an UST cavitation model.The MHD model accounts for turbulent fluid flow, heat transfer and solidification, electromagnetic field as well as the complex interactions between the solidifying alloy and nanoparticles by using ANSYS Maxwell and ANSYS Fluent Dense Discrete Phase Model (DDPM) and a particle engulfment and pushing (PEP) model.INTRODUCTIONAluminum matrix nanocomposites can offer outstanding properties, including low density, high specific strength, high specific stiffness, excellent wear resistance and controllable expansion coefficient, which make them attractive for numerous applications in aerospace, automobile, and military industries field (Bozic, 2010, De Cicco, 2009, Elshalakany, 2014, Goh, 2006, Jia, 2013 and 2015, Liu, 2014, Reihani, 2006, and Su, 2010).As shown in literatures (Aki, 1999 and Mussert, 2002), it is highly advantageous to use nano-sized ceramic particles to produce metal matrix nano-composites (MMNCs) since similar ductility and higher strength with the metal matrix can be achieved. Currently, there are several fabrication methods of MMNCs, including mechanical alloying with high energy milling (Chen, 1997) , ball milling (Filho, 2003), nano-sintering (Groza, 1999), spray deposition, electrical plating, sol-gel synthesis, laser deposition, etc. The mixing of nano-sized ceramic particles is normally lengthy, expensive, and energy consuming.Ultrasonic Stirring Technology (UST) has been extensively used in purifying, degassing, and refinement of metallic melt (Jian, 2005, Khalifa, 2008, Eskin, 2002, Xu, 2004, and Meek, 2006) mainly because introducing the ultrasonic energy into a liquid will induce nonlinear effects such as cavitation and acoustic streaming. SiC nanoparticles are widely used as reinforcement particles due to their relatively good thermal and chemical stability. Ultrasonic vibration can improve the wettability between the reinforced nanoparticles and the metal matrix (Lan, 2004, Cao, 2008, and Yan, 2011), which will assist to distribute the nanoparticles more uniformly into the metal matrix. Ultrasonic cavitation in liquids causes high speed liquid jets of up to 1000 km/h. Such jets press liquid at high pressure between the particles and separate them from each other (Hielscher, 2005)."

Jan 1, 2016

By F. Cheuk, E. Krause, V. G. Papangelakis, G. A. Moldoveanu, S. Abendschein

Systematic studies have been conducted at the University of Toronto in order to evaluate lanthanide extraction from clay minerals from different geographical regions. It was found that rare earth elements (REE) are easily recovered into an aqueous solution via an ion exchange mechanism by leaching with electrolyte solutions containing monovalent cations under ambient conditions. In this study we assessed extraction levels of individual REEs as a function of initial clay composition and leaching conditions. It was found that, in spite of variations in clay origin, all clays consistently reached peak REE extraction levels with fast kinetics. However, terminal extractions were clay-specific. The feasibility of using seawater as a leaching solution and potential synergies with ammonium sulphate as a lixiviant was also investigated. Seawater was found to be inferior to using ammonium sulphate, and provided no observable synergy in leaching performance when used together. The aqueous phase trapped in leached clays was shown to contain significant amounts of REE, as demonstrated in clay washing tests. Techniques to improve the REE concentration in leachate through process variations were investigated. However, it was found that most techniques capable of increasing REE concentrations in the resultant leachate also resulted in reduced REE extraction.

Jan 1, 2014

By T. P. Kostek

"Historically, gear pumps and motors have been popular in the mining industry because of their competitive cost, simple yet rugged construction, ease of rebuild, and relative long life and insensitivity to contamination. However, with the ever increasing ""popularity"" of fire-resistant hydraulic fluids, both users and manufacturers of gear equipment must make special considerations to enable the equipment to continue giving satisfactory performance even with the water-containing fluids.The paper discusses 60-40 invert emulsions and waterglycolsIntroductionMuch information has been published on the specific characteristics of the various types of fire-resistant hydraulic fluids. Fluid manufacturers' literature and other publications have dealt with such specifics as fire resistivity, seal compatibility and wear rate characteristics. Gear pumps and motors have been, and will continue to be, applied successfully in hydraulic systems employing both the ""invert"" emulsions (60-40) and water-glycols as the hydraulic fluid.Because most external spur gear equipment has been designed to function with petroleum oil as the fluid medium, certain guidelines must be followed to ensure satisfactory service life. FluidsThere are a number of different types of fluids which fall in the category of"" fire-resistant"" , the most common'being phosphate esters, water-in-oil emulsions, oil-in-water emulsions and water-glycols. The two in most prevalent use today as hydraulic fluids are the water-in-oil emulsions and the water glycols"

Jan 1, 1980

By S. C. Cohen, A. F. Mikkelsen

"This paper describes the improvements made to the operation of a liquid phase, 300°C, heat transfer system in the paste plant of an aluminum smelter. These improvements were achieved by replacing the original heat transfer fluid, a synthetic aromatic, with a new technology, petroleum-based product. This new fluid, Calflo HTF, provided better thermal stability, with lower toxicity, and improved plant working conditions.The procedures for fluid selection, changeout and performance monitoring are described along with a summary of control analysis over the last three years."

Jan 1, 1993

By David Meadows, Elmer Palmer, Steve Dixon

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large “state of the art” concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By M. Cossette, V. H. Tran

"How can the durability of asphalt pavement be doubled without increasing highway budgets? Asphalt containing asbestos can provide the desired performance with additional costs being made up by longer life. The addition of a low percentage of asbestos to an asphalt mix permits a higher asphalt content without any consequent loss in stability. It is mainly the higher asphalt content that provides improved performance and durability, although the fibrous reinforcement plays a key role in preventing the propagation of micro-fissures. As well, several international studies show that, thanks to the latest production techniques, no environmental hazards need be incurred.RésuméComment doubler la durée des chaussées d'asphalte sans augmenter les budgets de voirie? L’asphalte contenant de l'amiante peut offrir les performances souhaitées et l'augmentation des couts initiaux peut être rapidement compensée par une durée prolongée. L’addition d'une faible teneur en amiante courte il l'enrobe de bitume permet des teneurs en bitume plus élevées sans subir une perte de stabilité en conséquence. C'est principalement la teneur accrue en bitume qui assure un améliorations propriétés physiques et une augmentation des performances mécaniques, ainsi qu'on prolongement de la durée. Cependant, le renforcement fibreux joue un rôle clef en prévenant la propagation éventuelles micro-fissures. Les nouvelles techniques évitent tous risques environnementaux"

Jan 1, 1991

By P. Condori, G. Rech, J. Winnett

"Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken.A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material.Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores.This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit."

Jan 1, 2012

By R. G. McDonald

"High iron solution concentrations often result in the formation of basic ferric sulfate during the high temperature oxidation of sulfidic materials such as base metal and refractory gold concentrates. Consequently, the “Hot Cure Process” followed by limestone neutralization is required to facilitate subsequent processing and/or disposal of the leach residue. The present paper discusses strategies that can be employed to influence the composition and nature of the high-iron content leach residues produced during pressure leaching.INTRODUCTION Control of iron deportment in hydrometallurgical processing remains a key challenge for a range of reasons. Strategies generally relate to the control of conditions under which iron is optimally rejected (Demopoulos, 2009). Supersaturation provides the driving force for crystallization and this can be controlled by a number of factors that include (1) pH and/or Eh control, (2) the presence of matrix anions and impurities, (3) dilution, (4) complexation and dissociation and (5) manipulation of the rate at which the metal to be precipitated is released to solution. Each of these factors is impacted by temperature. Good control of crystallization is essential to the control of precipitate properties such as the degree of crystallinity, stability, particle size and quality which covers both the extent of impurity uptake and suitability of the precipitate for waste disposal. The quality and properties of iron precipitates in turn can impact downstream processing. It is the aim of this paper to discuss the generation of iron-containing residues produced during the pressure oxidation of sulfidic ores and concentrates and how the nature of these can be controlled to potentially facilitate further processing. A brief overview of several related topics will now be given and include, where relevant, discussion of work undertaken in our laboratories. In addition, brief discussions of selected process options that enable good control of iron rejection will be provided."

Jan 1, 2016

By Daniel Hodouin, Bruno Girard, Claude Bazin

"Mineral processing and smelting operations have the reputation of being complex processes. Process operators of these unit operations have acquired from experience and basic training a superficial understanding of the relationships between process output and manipulated variables. This understanding, which is a very valuable know-how for process control and optimization as well as for operator training, is however difficult to extract. This paper describes a time series based approach that can be used to extract this know-how, which can subsequently be used for operator training. The method is illustrated with an example taken from a smelting process.IntroductionThe emergence of Total Quality Management and Statistical Process Control philosophies in the North American industry (Brown, 1991 ), as well as the increasing popularity of the IS0- 900x standard accreditation, provide a strong incentive to review the training procedures for plant operators. The importance of employees training is acknowledged in two of the 14 points of Deming's road to quality (Deming, 1982) as well as by control engineering consultants (Hendricks et al., 1994). However guidelines for the operation of industrial processes are often transferred from an operator to another one with allowance for flexible interpretation of many operating rules. Such transfer is typical of complex industrial processes to which particulate processes of ore dressing and extractive metallurgy belong.Capturing the knowledge of experienced operators is often a difficult task. Cognition engineers are able to extract this knowledge and transfer it into rules that ultimately are implemented into expert systems. Cognition engineers are however not always available and plant supervisors may prefer to keep training as an internal liability. Another difficulty through interviewing of the process operator is its lack of willingness to transfer what he has learned by hard working to other people, whose ultimate goals are to develop computerized applications that may replace him in a near future, or reduce its importance in the production line.This paper shows that time series can be advantageously used to capture the average process understanding of plant operators and to help reviewing training procedures. The method s illustrated with data collected during normal operation of electric arc furnaces and it is shown how the approach has led to a fruitful discussion between process engineers and operators that ultimately provided savings of more that $200,000 per year per furnace. There are 9 furnaces in the studied foundry. Such savings are not the results of application of advanced control strategies nor of ""miracle press button software», but of an improve awareness by engineers and operators of the importance of properly defining the operating procedures to control a process."

Jan 1, 1996

By V. V. Pankov, W. R. Chen, L. R. Zhao

Diffusion nickel aluminide and overlay NiCrAlY coatings were deposited on single crystal Ni-base superalloy CMSX-4 substrate using the chemical vapour deposition and cathodic arc evaporation techniques, respectively. The NiCrAlY coating underwent a post-deposition heat treatment in an argon atmosphere at 1100°C for 2 hours. All the coated specimens were subjected to furnace cyclic oxidation testing at 1000°C up to 1500 one-hour cycles. The morphology, elemental composition and phase constituents of the oxide scales formed on the coating surface were analyzed using scanning electron microscopy, energy-dispersive spectroscopy and X-ray diffraction. It was observed that the diffusion aluminide coating experienced accelerated weight gain at an early stage of the test (150-400 cycles), whereas the overlay NiCrAlY coating fabricated by cathodic arc evaporation maintained steady-state weight gain throughout the entire 1500 cycle test duration. This difference in oxidation behaviour between the two types of coatings is attributed to the early development of nickel-aluminum spinel on the surface of the diffusion aluminide coating, in contrast to the stable aluminum oxide scale formed on the overlay NiCrAlY coating during cyclic oxidation testing.

Jan 1, 2015

By P. E. Weidmark

"Energy, Mines and Resources Canada has published the first in a new series of reports that will examine selected mineral products that are imported.""Vanadium - An Imported Mineral Commodity"" looks at one of the 32 raw materials for which Canada currently is totally dependent on foreign sources of supply. Vanadium is used in Canada mainly as an alloying element in the manufacture of high-strength, low-alloy (HSLA) steels.The series will examine the supply systems for various selected imported non-fuel minerals, as an aid to developing policies that might lead to reduced dependence on external sources. Each report in the series will address a numberof questions:What countries do the mineral and its principal sub-products come from?How do they get to Canada?What are they used for?How vulnerable is the supply chain to disruption?Are there alternative sources?Are substitute materials available?In summary - how serious is Canada's supply problem for the mineral in question, and what should be done about it?Mineral Bulletin MR 188, ""Vanadium - An Imported Mineral Commodity"", is available for $3.00 ($3.60 outside Canada) from authorized government bookstore agents and many other bookstores, or by mail from the Canadian Government Publishing Centre, Hull, Quebec, KIA OS9."

Jan 1, 1981

By Francis Dakubo, Courtney Young, Avimanyu Das

"Hydrometallurgy of copper ores typically involve acid leaching followed by solvent extraction and electrowinning (SX/EW). EW is the final purification stage in which a voltage is applied across two electrodes causing the copper ions to reduce and deposit on the cathode. Applied voltages are near 2 volts with current densities around 300 amps/m2. In this study, research was undertaken to decrease the energy consumed in the EW process. To do this, various cell designs were constructed and tested in which a membrane was used to separate the cathode and anode compartments with concentrated solution from SX serving as catholyte and raffinate from SX serving as anolyte. Therefore, copper in the concentrated solution would be deposited on the cathode while ferrous in the raffinate would be oxidized to ferric at the anode. Because it is assumed that ferric acid leaching is used, resulting ferric would be recycled to the leaching process. A positive side effect of the envisioned process would be the elimination of oxygen evolution at the anode and thus the prevention of acid-misting. After a cell design was selected, it was used to test a number of variables: flowrate, concentration, temperature, ion-exchange membrane, and applied voltage. Following experiments in which variable ranges were determined, statistical modeling was conducted using STATEASE software. Optimal results indicate the voltage can be decreased to 1.5-1.7 volts with current densities of 300-400 amps/m2. Significant reduction in the energy consumption was accomplished by reducing the applied voltage. Furthermore, current efficiencies and copper production rates was increased by application of the membrane.INTRODUCTIONLeaching of copper ores is achieved using mostly sulfuric acid. The copper pregnant solution is contacted with an organic solvent or resin adsorbent which picks up copper ions as in Equation 1:"

Jan 1, 2016

By G. R. Haiden, E. Henderson

"An LHD teleoperation and guidance system, developed at the Ontario Division of Inco Limited, has been demonstrated in operation at Copper Cliff North Mine (CCNM) since late September, 1993. The tests performed to date have evaluated the feasibility and production viability of multiple LHD operation, from surface by one operator.The systems technology required to accomplish this consists of an electronic monitoring and control package mounted on the LHD; a high bandwidth mining computer network capable of providing radio frequency coverage; and an operator control console which provides an operator workstation for multiple LHD operation.This paper discusses the systems required to accomplish the task of LHD teleoperation and guidance, the benefits of multiple machine operation and future research and development directions. IntroductionSince underground mining began, persolU1el have entered the mine workings to mine ore. Today, however, the rapid advancement of modem telecommunications, computer hardware and software technology has opened the door to remote mining technology that was considered unfeasible a few years ago. This paper discusses the ingredients of remote mining technology that have been developed at Inco Limited.Figure I represents an historical view of the application of electronics to LHD operation at Inco Limited. In 1980, the first radio remote controls for the operation of LI-IDs in large open stopes were tested. The successful application of this technology at Inco went hand-in-hand with the development and application of the Vertical Crater Retreat mining method. The combination of these two advances had a very positive effect on the productivity in the mid-eighties at Inco. In 1991, the Mines Research Department of the Ontario Division advanced remote control technology by developing a high capacity underground mining telecommunications system. This system is capable of moving voice, data and video information throughout the mine workings. The system is based on broadband communication technology found in most automated factories, with the added benefit of providing the information to and from mobile equipment through radio interfaces. The first test of the system consisted of an operator teleoperating a single LHD (on the 3000 ft level) from the surface. The next test on September 13, 1993, demonstrated the first production application of multiple LHDs being run from surface with a single operator."

Jan 1, 1994

By D. A. Stokes

"In October of 1980, Fording's 15 000-ton capacity clean coal silo was put into operation. The silo was unique in that it was designed to allow the mass flow of material, coupled with a sophisticated computer-controlled dynamic loadout/weighing system.On May 1, 1982, an explosion, attributed to a methane buildup, devastated the top of the silo. .As a contingent plan to minimize the effect of the production loss the conveyance to the silo top was reconstructed and the silo' was back in operation by mid-June 1982, although the silo top was left open to prevent further methane buildup. As dust emissions occurred during loading ofthe silo, an extensive study was undertaken to establish dust control for the silo, while at the same time providing methane detection and control.The study, conducted for Fording by the Cambrian Engineering Group of Calgary, involved an extensive search and investigation of existing coal silos. The study concluded that there IS no universally accepted method of controlling methane emissions in coal silos.The study also produced a unique conceptual design for handling methane, while at the same time, protecting the environment . Fording's Clean Coal SiloThe silo, located at Fording Coal's Fording River metallurgical coal operation, is utilized for the storage and load out of cleaned thermally-dried metallurgical coal.The silo was constructed in 1979 and 1980 to reduce unit train loadout times and to facilitate the handling of “special shipments"" of coal. The silo went into operation in October 1980, under manual control and utilized computerized, automated loading by February 198I.The silo is 21 m in diameter and 76 m high, with a nominal capacity of IS 000 live tonnes. The coal storage portion of the silo is 21 m in diameter and 48 m high, utilizing 2 steep-angled hopper outlets allowing mass flow of the stored coal during train loading. Each hopper has a control gate and a discharge chute, one chute for bulk loading, the other for trim loading of coal into the rail cars."

Jan 1, 1986

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By Janice Zinck, Ian London

In recent years, the secure supply of critical and technology metals has become increasingly important tomajor industrialized economies that seek to sustain their industrial base and develop advanced technologies, such as clean energy. Canada, with its significant reserves of rare earth element (REE) and other metals, has an opportunity to supply some of the global demand for these materials. However, to transition from promising mineral deposits to marketable products, investment in strategic research and development (R&D) and expertise is needed to address the complex technological challenges around the production, separation and processing of these metals, and to better understand the global market for these key commodities. To this end, in its April 2015 budget, the Government of Canada committed to invest $23M over 5 years to accelerate production of REE and chromite/ferrochrome. The goal of this program, developed in close association with industry, is that Canada contributes a sustainable supply of REE to the global market. The research and development program will provide the technological capacity to establish a Canadian REE industry. This paper will discuss REE R&D advances achieved in the first year of the program in areas of mineral characterization, beneficiation, leaching, separation and environmental management and will highlight the Canadian model of collaboration where industry (e.g. prospective producers, technology companies), government, academia and other stakeholders work closely to ensure that the R&D is targeted, innovative and effectively deployed and commercialized.

Jan 1, 2016

By M. Romana

"RMR geomechanics classification is being used all over the World as a useful tool for tunnel predesign and construction. Bieniawski (1989) provided guidelines for tunnel excavation and support, according RMR numerical values; guidelines which are now included in almost all tunnelling books, regulations, and Internet portals. But in the last 25 years tunnelling techniques have changed and some of the guidelines have become obsolete.. The conditions of tunnels for the 1989 guidelines application were: horseshoe shape; 10 m width; vertical stress < 25MPa; construction by drilling and blasting. Actually a substantial number of tunnels are mechanically excavated. The tunnel themselves are now bigger: a span of 14 m. is very common for transportation tunnels. The guidelines included the following concepts: excavation method, rock bolts (20 mm diameter, fully grouted), shotcrete, steel sets. There is an increasing gap between the 1989 guidelines and the practice: in many tunnels different to-the-case excavation and support requirements are established. Bieniawski himself has published a paper (Lowson & Bieniawski, 2013) with different guidelines based in Lowson’s practice, with no explanations and/or justification.In this paper a new set of RMR tunnelling guidelines is proposed taking account of the actual industry conditions, and increased safety regulations. The 5 classes’ limit RMR:values (80,60,40,20) are no more useful actually: Values of RMR (70, 50, 30) are used in practice to define quite different tunnelling techniques. Consequently a 10 subclasses system is proposed. Each subclass covers a span of 10 RMR points. As the number of mechanically excavated tunnels has increased a new correction factor is necessary, according the excavation method.The proposed 2014 RMR guidelines are for tunnels 10 to 14 meters wide, the world practice for new roads/railways tunnels. Many tunnels for water/ services are smaller with smaller support needs. Wider than 16 m caverns are out of the RMR system.It is not possible, nor desirable, to propose only a value for support in each subclass. The new guidelines propose an interval of values for certain types of support. More pessimistic values must be chosen for wider tunnels, tunnels with lower RMR values in each class and cases when a higher safety factor is asked for. More optimist ones are chosen for narrower tunnels, and higher RMR values. Some alternatives are almost complementary, others are contradictory. Sometimes several different techniques are proposed Guidelines are not automatic options. Good engineering judgment must be used when choosing between the different alternatives. Guidelines are not mandatory suggestions."

Jan 1, 2015