Search Documents

By L. A. Mells

"A laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the applicability of a radium selective ion exchange complexer for removing radium from Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. under contract to the Department of Supply and Services using the Saskatchewan Research Council facilities located in Saskatoon, Saskatchewan.The results of this work showed the ion exchange complexer, Dowex XFS 43230.00, to be efficient in removing radium from contaminated water of uranium mining operations with the ultimate loading capacity of the resin on one type of water treated being determined as approximately 1,600 Bq/cm3 of new resin. Although this resin has potential application for treatment of effluent streams in uranium operations it has been identified that the resin efficiency and capacity is directly related to the chemistry of the water being treated and site-specific testwork is required in order to establish reliable design data for full-scale operations.IntroductionThe possible applicability of a radium-selective ion exchange complexer for removing radium from Canadian uranium mining effluents had been identified and discussed as a possible alternative to present radium removal methods during a review of disposal technology options for the National Uranium Tailings Program of the Department of Energy, Mines and Resources(1). Work by other workers(2.3) had shown the complexer to be very efficient in removing radium from contaminated water. Also, plant trials on contaminated minewater at the Mt. Taylor uranium mine in New Mexico is reported to have shown the resin complexer to be efficient under plant operating conditions.As a result, a laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the suitability of this resin for Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. (MCEL) under contract to the Department of Supply and Services using the Saskatchewan Research Council (SRC) facilities located in Saskatoon, Saskatchewan."

Jan 1, 1985

By Robert Marchand

_ North-western Quebec _ Bousquet mining district _ 21 M oz mining camp _ 100,000 t/yr (400 t/d) _ Shrinkage : 52 % _ Longhole : 40% _ Development : 8% _ 5 days/week _ 120 employees _Discovered in 1936. _12 changes of ownership. _Exploration & development : 1987 _Commercial production : 1990 _Shaft deepening : 1995 _Internal shaft : 1999

Oct 1, 2001

Infrared spectroscopic data collected using HyloggerTM technology is being used to assess the mineral composition of Archean iron ore bedrock and Cenozoic detrital units in Western Australia’s Pilbara region. Analysis of infrared spectra enables quantification of: (1) composite iron mineralogy, (2) composite clay mineralogy, (3) hydrous silicates and (4) carbonate mineral abundances. Stratigraphic and rock mass unit logging of core has identified several detrital and bedrock units recognisable across the Pilbara. However, due to alteration related to mineralisation, weathering and later stage precipitate overprinting, it can often be difficult to assess the detrital-bedrock boundary and the occurrences of specific geotechnical units in the detritals and bedrock, particularly when using non-core drilling techniques and traditional geochemical assays. Infrared spectroscopic data collected concurrently on core from several sites has shown distinct correlation against existing unit subdivisions and associated geochemical parameters. Where infrared spectroscopic data have also been collected on rock chips recovered from reverse circulation infill drilling, these correlations allow robust geological and geotechnical models to be developed based on the typical mineralogical-geochemical signatures. The geotechnical sub-units identified in core can be readily distinguished using the various iron and clay minerals captured by the HyloggerTM technology as opposed to total iron, potassium, and alumina captured by geochemical assays. Further, some of the minerals targeted by infrared spectroscopic analysis (eg gibbsite, white mica, vitreous goethite) and their ubiquitous presence as the products of weathering, assist in recognition of various ancient weathering surfaces and help to define the origin of the material, whether bedrock or detrital. Overall, HyLogging of core and chips allows important mineralogy focussed data to be captured at minimal additional financial outlay. Correlations against geochemical unit identifiers are robust both within deposits and between deposits. Significant improvements in the confidence of geological and geotechnical models are attained.

Jan 1, 2015

By P. K. Kaiser

3-D virtual reality (VR) visualization has opened new opportunities for complex 3D (x, y, z), 4D (x, y, z, t) or even nD data interpretation. The integration of common earth models (3D geologic data), mine models (3D excavations and stress), extraction models (1D time sequencing or mine sequencing) and nD monitoring data (e.g., seismic event parameters) into a common mining process model provides a platform for experts in various fields to better design, evaluate, monitor and modify mine plans throughout a mine?s life; from feasibility, through operation, to closure. Viewing seismic data in a stereoscopic VR environment within a mining process model offers data interpretation processes previously unavailable at lower dimensionality. MIRARCO has developed data analysis and viewing processes specifically designed to enhance microseismic and seismic data interpretation in a collaborative, immersive VR environment; bringing mine personnel and expert consultants together to evaluate data and make strategic decisions for cost effective and safe mining. Seismic events cause immediate hazards (rockbursts) and microseismicity causes gradual hazards through its cumulative effect in rockmass degradation. The focus of this paper is on understanding seismicity from a mine safety and mine planning perspective; in particular, how seismic migration patterns relate to the rockmass response to mining. The benefits of innovation in seismic data interpretation are significant, e.g., for hazardous work area identification, allowing better formulation of re-entry policies and workforce allocation planning, as well as allocation of effective support systems to strategic areas of elevated risk. Better understanding of the overall response of a mine to extraction also facilitates mine planning and design, assisting in reducing production costs and thus in enhancing profitability.

Apr 1, 2005

"These standards were developed by the CIM for use with the value or worth of a Mineral Property as opposed to “evaluation” where the key objective is an economic assessment or determination of the economic merit of a propertyP1 .0 BACKGROUNDPl.1 There are at present no comprehensive standards for valuation of Mineral Properties in the Canadian mining industry. The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) specifically recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties.Pl.2 On May 5, 1999 at the Calgary Annual General Meeting, CIM Council approved the formation of a Special Committee on Valuation of Mineral Properties (CIMV al) to be co-chaired by Keith Spence (Chairman of the CIM Mineral Economics Society) and Dr. William Roscoe (Roscoe Postle Associates Inc.).Pl.3 The mandate of CIMVal is to recommend Standards and Guidelines for Valuation of Mineral Properties to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges.Pl.4 The members of CIMVal represent of a mix of professional disciplines and experience in the field of Mineral Property valuation:Keith N. Spence (Co-chair), Alliance Pacific Resources Inc., TorontoWilliam E. Roscoe (Co-chair), Roscoe Postle Associates Inc., TorontoMichael J. Bourassa (Secretary), Aird & Berlis LLP, TorontoChristopher R. Lattanzi, Micon International Limited, TorontoRoss D. Lawrence, Watts, Griffis and McOuat Limited, TorontoPaul E. Lunney, Noranda Inc., TorontoCraig A. Roberts, Pacific International Securities, VancouverDavid A. Scott, CIBC World Markets, TorontoIan S. Thompson, Derry, Michener, Booth & Wahl Consultants Ltd., VancouverWilloughby A. Trythall, retired Placer Dome executive and consultant, Vancouver"

Jan 1, 2003

By Bruce Peberdy

Outline ?Building Systems ?Climatic Effects ?Thermal Effects ?Building Components ?Building Materials ?Structural Deterioration ?Maintenance Considerations

Nov 1, 2011

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By H. Gharahbagheri, S. Shafiei Zadeh, H. Hassan Nejad, Reza Roostaazad

In this paper, dissolution of vanadium from mining residue, in which vanadium is associated intimately with magnetite ore, was investigated via both bacterial ( aerobic and anaerobic) and fungal activity. Although bacterial activity was tangible, it could not reduce and dissolve vanadium in both aerobic and anaerobic experiments. However, in fungal leaching, after 30 days about 36.9% and 29.7% of vanadium was dissolved for a pulp density of 10 and 30 g/l, respectively. At the end, the concentration of metabolites usually produced by fungal activity was optimized and oxalic acid was chosen as the main agent for the leaching process.

Jan 1, 2014

By Aleksandar N. Nikoloski, Tendekayi Tapera, Glen P. O’Malley

Chalcopyrite (CuFeS2) and enargite (Cu3AsS4) are among the most important copper sulfides. At present, many known deposits of these minerals are uneconomic to process because they are of too low grade, insufficient size or too remote to be cost effectively treated with conventional technologies that can deal with their refractory nature. Therefore, developing an effective, low cost extraction process for recovery of copper from them is important. The research presented in this paper will deal with potentially cost effective strategies involving catalysed processing, studied under conditions relevant to recycle heap leach conditions. The present account summarises some of the main findings from the research program carried out at Murdoch University between 2014 and 2018 that has investigated the effects of the common leaching parameters, major and minor species present in the leach system and additives on the rate and extent of copper extraction from low-grade ores, in which primary copper sulfide minerals such as chalcopyrite and enargite were the dominant copper minerals. The study involved batch leaching tests, detailed structural and mineralogical characterisation and thermochemical modelling under conditions relevant to heap leaching. The results have demonstrated that silver in particular has a strong catalysing effect on the extraction of copper from ore under the leach recycle conditions and, at an adequate dosage, can effectively overcome surface passivation, enabling almost complete extraction of copper from chalcopyrite as well as enargite. The aim of this paper is to present the effect of the studied additives and to briefly elaborate on the mechanism of the silver catalysed leaching process. In addition, the presence of certain secondary agents was shown to lower the critical dosage of silver and promote extraction. The data from the study allowed the development of a theory for the silver catalysed reaction mechanism, which enables further optimisation and cost-effective application of this strategy in practice. INTRODUCTION Researching the extraction of copper from chalcopyrite is important as it is the most abundant copper mineral in the earth’s crust. The majority of ores containing this mineral are processed by flotation to produce a concentrate, followed by smelting and electrorefining. However, most reserves available nowadays are of low grade or limited in size, and therefore not suitable for this conventional approach. Hydrometallurgical processing via heap leaching with or without the aid of bacteria has been shown to be potentially economical. Chalcopyrite is refractory though and suffers from slow leaching kinetics and poor overall extraction, so understanding the mechanism of how it leaches has received significant attention by researchers working in this field over the past 50 years. The refractoriness, which is the main issue with the hydrometallurgical approach, is generally described as passivation of the chalcopyrite surface whereby a surface coating is formed that blocks the reaction interface or wetting of the chalcopyrite, limiting the copper extraction. Exactly what this layer is made of or how the issue could be overcome has been the subject of intense study and debate for many years. One of the limitations of the work to date is that much of the research focus has been on typical initial leaching conditions, while there has been relatively little research into how the leaching is affected under recycle solution conditions where certain metal ions (Fe, Mg, Al) have often accumulated in the liquor. This occurs because the leach solution exiting a heap contains many species from the dissolution of gangue minerals and typically this solution is returned to irrigate the heap, once the copper has been removed, leading to an accumulation of these species.

Jan 1, 2019

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By Per Hedvall, Jan-Eric Ståhl

"The main objective of this study is to introduce the new Sandvik’s production cost-model within Crushing & Screening (C&S) technology. So far, there have been different ways of determining different production costs in the industry, however, the previously published and presented methods have not been very efficient in calculating the costs per product and metric ton. Accordingly, the current study has been planned and started in collaboration with Lund University to provide an accurate and easy to implement cost estimation program to determine the costs for crushing and screening plants worldwide.The proposed model has been adapted to fit the C&S processes of different rocks/ores fractions. The result is presented as cost per ton of the end product(s).Within this paper the cost estimation results for 3 different crushing and screening plants are presented based on the information obtained from the following sources: a) documents at Sandvik SRP, b) Sandvik’s crushing & screening internal/external machines/plants data and information, c) literature studies, including the use of Sandvik’s internal/external simulation and software programs, d), visiting the crushing and screening plants ,e) interviews, information systems’ data, and, f) testing and observations by ourselves.In order to improve the level of accuracy and the validity of the attained results, simplistic Monte-Carlo simulations have been used, where needed. The achieved results, so far, have proven the reliability of the model. The calculated cost estimations have shown an accuracy over 80% when they compared with real cost data obtained from plant practices.The current cost calculation model, will offer the possibility of:•,Calculating the production costs in proposed and/or existing C&S plant.•,Making detailed cost analyses for the end product(s) in proposed and/or existing C&S plants.•,Determining the profitability of each finished product when it’s required.•,Cost optimization by potentially cutting the cost for part of C&S plant with an existing plant practice"

Jan 1, 2016

By L. Li

To accommodate the large payloads and harsh operating conditions associated with heavy vehicles in the mining industry, off-the-road (OTR) tires are typically used with heavy mining vehicles. These tires have increased abrasion and wear resistance due to their thicker tread, sidewall and bead thicknesses. Given these features, OTR tires are much stiffer than conventional passenger vehicle tires and cannot be mounted to a single-piece rim without damaging the structural integrity of the tire during the mounting process. Therefore, multi-piece wheels are used with OTR tires to facilitate mounting. While these assemblies are necessary, several instances of their failure have been reported to result in injuries or fatalities within the mining workplace. Many of these failures were specifically reported to be caused by the disengagement of the wheel lock ring - a component used to securely engage the assembly during operation. In this study, a threaded-connection locking mechanism has been proposed in place of the traditional lock ring design. The performance of this threaded-connection was numerically evaluated in a pull-out test against a conventional five-piece wheel assembly. The pull-out test was devised as a means of quantifying the engagement ability of each wheel?s locking mechanism. A high degree of modelling accuracy was maintained throughout the analysis by validating the vertical and horizontal static loaddeflection behaviour of the rim model of the five-piece wheel assembly against experimental data. Through validation, the model data were found to be within 10.5 and 4.80 %, for vertical and lateral loaddeflection behaviour, respectively. Results from the pull-out analysis found that the threaded-connection demonstrated a 113 % increase in the force required for disengagement to occur relative to the conventional five-piece design - a force of 9,550 kN in total.

Aug 1, 2013

By F. Boudreault, C. Hendricks, M. Scobie

Drilling accuracy represents an important quality control factor in minimizing dilution. Apart from geology, the factors governing drilling accuracy are largely within the control of the mine. Setup location and alignment, as well as actual drilling accuracy, can all be monitored toward their improved control. Trajectory deviation during drilling, although usually beyond the control of even the most experienced and conscientious driller, can be accounted for (if not full controlled) by down-hole surveying of blastholes prior to explosives loading. This paper reviews the available instrumentation for improved drill setup and recent field experience with several commercial systems designed for monitoring borehole deviation. It reports on a recent survey of 50 Canadian mines which use blasthole stoping and addresses the reasons for the apparent lack of interest in instrumentation: i.e. does this reflect a lack of awareness of the technology, perceived inadequacies in its performance or a predominant reliance on productivity (drilling and mucking) as a measure of operational efficiency? The survey findings supported the latter viewpoint and showed that very few Canadian mines operate drilling incentive programs that are related to drilling accuracy.

Jan 1, 1994

By Dougla McDonald, Richard Poulin

"Most mine managers in Canada today will agree that one of the keys to mining efficiency and productivity is their human resources. A5 a result, many mines develop some sort of incentive designed to tap their employees' capabilities to the fullest extent. Historically, the most common plans used have been ""piece-rate"" plans, where individual or small groups of miners are paid a financial bonus based on some measure of their productivity. Recently, however, incentive plans that take a more team-based approach have been developed in some Canadian mines. One such plan will be defined in this paper, and its popularity in the industry today discussed.Gainsharing PlansThere are two primary components to a gainsharing plan. The first is a cash incentive, which is paid to all employees and based on factors that are highly correlated with employee productivity, and key to the profitability of the mine. For example, the typical gainsharing cash incentive is based on the cost/unit of metal produced. Management (in consultation with employees in some cases) will establish the budgeted cost per tonne, and any savings in this amount is shared between the company and the employees. The second is a management philosophy and associated communication network, which is designed to foster an environment that encourages information exchanges, communication, participation, and trust between employees and management. The typical gainsharing communication network consists of two tiers of committees. The first, operational committees, include all employees working in the same department or departments which frequently interact. The employees meet monthly with management personnel to discuss problems encountered and brainstorm for solutions. In most cases, these committees will nominate a person in the group to structure the meeting to maximize its efficiency. The second, the screening committee, is a single group consisting of representatives from the various operational groups, whose primary job is to ensure that the plan is effective, and the objectives and results generated by the plan remain consistent with the mine objectives. In short, gainsharing plans tell employees that their bonus depends upon performance and then gives them the opportunity and incentive to affect that performance. The opportunity is provided by a communication network and positive management practices, and the incentive comes in the form of ""intrinsic"" rewards of participation and the ""extrinsic"" rewards of the bonus payments. Figure I will clarify the relationship between the intrinsic and extrinsic rewards."

Jan 1, 1995

By R. C. Reed, A. Akhtar

Oxidation of the third generation cast single crystal, nickel-base superalloy CMSX-10 is examined using isothermal tests at 900°C and 1000°C for times ranging from 20 hours to 100 hours. X-ray diffraction, scanning electron microscopy and energy dispersive secondary X-ray analysis were used to characterize the microstructure. It was found that the external scale formed at 1000°C is made up of (Ni,Co)O and the spinel NiCo2O4. The (? + ? ') microstructure of the superalloy transforms into the intermetallic (3 phase prior to the onset of internal oxidation. Internal oxidation results in the formation of (Ni,Co)Ta2O6 and (Ni,Co)WO4. No evidence was found for the formation of alumina (Al203), and the spinels NiCr2O4 and NiAl2O4 in this third generation superalloy. Results of the laboratory investigation are compared with those of an aero-engine turbine blade removed from service and examined earlier.

Jan 1, 2004

By Xuanxue Mo, Kaihui Yang, Steven D. Scott

Abstract -The Changning-Menglian metallogenic belt in western Yunnan, China, is characterized by the occurrences of both Pb-Zn-Cu and Cu massive sulfides in Permo-Carboniferous mafic volcanic sequences. These deposits were formed in a back-arc basin at a rifted continental margin in the Paleozoic Tethys Ocean. Pb-Zn-Cu deposits are associated with alkalic basalt, andesite, and lesser felsic volcanic rocks intercalated with limestone, which probably formed along an immature rifting segment on a continental basement. These volcanic rocks are enriched in K, Ti, LREE, and other incompatible elements, and have the attributes of alkalic within-plate basalt. An extensive unit of sulfide- carbonate-silica shale in proximity to massive sulfides contains high values of Mn, As, Mo, W, Sn, Sb, and Hg, and has REE patterns that are similar to the volcanic rocks. This, together with the graded bedding in the footwall volcanic rocks, suggests that the sulfides precipitated in a shallow, unstable, and carbonate-saturated volcanic basin. A stringer zone is traced downward for 500 m below the massive sulfide orebodies. It is characterized by an upper sericite-quartz zone and an extensive lower skarn alteration with enhanced W, Sn, and Bi. Lead isotope data show both continental basement and magmatic sources may have supplied the ore metals. Cu deposit and occurrences are hosted by tholeiitic units that represent the mature spreading segments in the back-arc basin. The tholeiitic lavas have LREE-depleted or flat REE patterns similar to MORB or back-arc mafic lavas. The cupriferous massive sulfides are overlain by an extensive unit of chlorite-magnetite or ochre, suggesting a relatively oxygenated oceanic basin. Ni and less Co mineralization is found in dolomite veins of the stringer zone. Enhanced concentrations of Ni, Co, Au, and As are found in the massive sulfides and in sulfide-rich tuffites. The geological setting and mineralization of the Changning-Menglian belt has similarities with modern back-arc basins such as the Manus Basin in the western Pacific.

Jan 1, 1999

By Andrew Bamber

A fast and objective spreadsheet-based model for the financial evaluation of innovative mining and processing strategies such as pre-concentration vs. a conventional base case is presented. The size and grade of the deposit must be chosen, from which a mining rate is selected. Expected operational data for the deposit as well as any mill testwork and results from the pre-concentration testwork are entered as input variables on the sheet, and cost and revenue impacts are calculated in the ?Output? sheet. A capital sum and operating costs for the initial mine and mill development as well as the pre-concentration facility are calculated. The net changes in capital and operating costs are calculated, and impacts on revenue through changes in metal recovery are also calculated. These outputs are used to calculate the overall impact on the cutoff grade and thus the size of the mineral reserve using a generic grade-tonnage model. The NPV and NPV profile of the two scenarios is calculated, with variations in basic parameters such as operating cost, capital requirements, metal price or grade as well as discount rate. Cost and revenue impacts are evaluated and compared to the baseline to establish a positive or negative impact overall. Different scenarios of grade, tonnage, mining rate, process performance, capital and operating cost structure can be explored using the model. Outcomes projected by the model for case studies conducted thus far have been calibrated against internal estimates by the sponsoring organizations and found to be accurate to within 30%, confirming the utility of the model in practice.

Oct 1, 2009

By Robert Cameron, Colin Ashton, John MacNeil, Leo Piciacchia

"The in pit dam construction and utilities relocation, known as the East Mine Corridor Relocation (EMCR) project, was developed to extend the life of the east side of the Base Mine pit by two veal's. This will result in the recovery of an additional 80 million barrels of oil and delay expenditures associated with the opening of the North Mine by two years. To accomplish this, a large in pit earth structure was required to provide a new embankment foundation for relocating a public highway, four powerlines, a natural gas back-up pipeline, a substation, and a conveyor train. This structure would also he required as a temporary dam 10 contain mature fine tails on the west side until mining is completed in the east mine corridor area, that will then be filled with fluid.The in pit dam, known as The Highway Berm, is 2.5 km long, 63 m high and has 42 million m3 of engineered soil added to the already existing end-dumped soil volumes. To complete the design and construction of a structure of this magnitude, in the very short time frame of two-and-a-half years, presented many new challenges. The main challenges faced were: designing while construction was ongoing; designing without the use of clay cores or sand filters; using relatively non-select overburden material; proper dewatering and base preparation; changing from construction of 50 m high spoil piles to a high specification construction operation; compacting lifts with heavy haulers; constructing during the winter; and monitoring movement of the structure with satellites."

Jan 1, 1995

By C. J. Edmonds

Of the gold mined in Canada over 90 percent is extracted from the ore by the process of "cyanidation". In this process crushed ore is treated with lime to provide "protective alkalinity" and cyanide, usually in the form of sodium cyanide. The gold is dissolved in the cyanide solution, which after further treatments for clarification, is precipitated by the addition of zinc dust. Wastes from the process consist of tailings which will contain cyanides. Water consumption, mill size, effluent quantity and quality are depicted in transparency (1). It should be noted that as far as the wastes are concerned it has been impossible to postulate a typical situation. Variation from the above data will occur. A summary of data from tailings pond effluents is presented in transparency (2). The figures in parentheses indicate the usual range of values for the parameter.

Jan 1, 1973