Search Documents

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By Lassi Klemettinen, Ari Jokilaakso, Dmitry Sukhomlinov, Pekka Taskinen

The solubilities and distributions of molybdenum and iridium in iron silicate slag and copper-iron mattes were studied using an equilibration-quenching technique and subsequent direct phase composition analyses by EPMA (Electron Probe X-ray Microanalysis) and LA-ICP-MS (Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry). The equilibrations were carried out on a wide matte grade interval, ranging from 55 wt-% Cu to 75 wt-% Cu, in pSO2 = 0.1 atm at 1300°C. The results in equilibrium with a solid iridium-molybdenum alloy indicated an iridium solubility of 150–500 ppmw in the sulphide matte, depending on the matte grade, and a molybdenum solubility of 100–600 ppmw. Iridium was distributing predominantly in the sulphide matte with the distribution coefficient of 10+3 - +4 but molybdenum deported predominantly in the slag with Lm/s(Mo) = 0.02–0.1. The effects of alumina and lime additions in the smelting slag were also examined. INTRODUCTION Iridium is a highly siderophile element (HSE), which means that it is incompatible with the sulphide forming elements and possesses a small solubility in mattes, such as copper- and nickel-iron sulphide melts. Molybdenum behaves only modestly in that way (Walker & Li, 2008; Righter et al., 2017). They both are known to be trace elements accompanying copper and nickel sulphide ores. No solubility data, however, are available for them in copper-rich sulphide mattes. Geochemical data on the behaviour of Ir and Mo deal mostly with low-iron silicate systems, e.g. basaltic melts, and high-sulphur sulphide solutions and mattes (Ertel et al., 2008; Fonseca et al., 2007). They also indicate that Ir and Mo dissolve in silicate melts primarily as oxides and not as electrically neutral metal species. Most geological data of iridium focus on high-sulphur systems of the monosulphide composition and typically Fe-Ni mattes where copper is a trace element (Fleet et al., 1996; Sattari et al., 2002). Direct solubility measurements for mattes and iron-lean silicates have also been made using pure Ir or an Ir alloy as the saturation phase (Borisov & Palme, 2000; O’Neill & Eggins, 2002; Makovicky & Karup-Møller, 1999; Ertel et al., 2008; Mungall & Brenan, 2014). A recent summary about the solubilities of HSE’s in iron- and sulphur free silicates is available in Laurenz (2012). The thermodynamics of molybdenum partitioning between oxides and Fe-S-O melts was studied by Mengason et al. (2011). Their results indicate strong accumulation in the iron-rich sulphide in reducing conditions (pO2 = 10-9.6 atm in Ni-NiO equilibrium at 1050°C). Molybdenum dissolves in iron-lean silicate melts as MoO3 species in oxygen pressures above the Fe-FeO equilibrium and as MoO2 in more reducing conditions (Farges et al., 2006; Righter et al., 2017).

Jan 1, 2019

By J. E. Armstrong

"Pinchi Lake and Bralorne Takla mercury mines; Canada's only producing mercury mines during the past war (1939-1945); occur within the Pinchi Lake mercury belt. This belt is in central British Columbia; and is approximately 150 miles long extending from southeast of Fort St. James northwest to the headwaters of Omineca river.During the field season of 1937 cinnabar was discovered by J. G. Gray of the Geological Survey in Permian limestone on the north shore of Pinchi lake, where the main showings of the Pinchi Lake mercury mine were later developed. Following the publication of Gray's report claims were staked in the spring of 1938, and later that year were optioned to the Consolidated Mining and Smelting Company, and in June 1940 a reduction plant with a rated capacity of SO tons a day was brought into operation. In 1943 the plant had a capacity of more than 1,000 tons a day. The grade of ore treated was reported to average S to 10 pounds of mercury a ton, and production during the years 1940 to 1944 exceeded 4,000,000 pounds. The Bralorne Takla mercury mine, which is 90 miles northwest of the Pinchi Lake mercury mine, was brought into production in November 1943 with completion of a 50-ton mill. During the next 10 months more than 100,000 pounds of mercury were recovered, and the grade of the ore was reported to average 15 to 20 pounds of mercury a ton. During the war, production from these two properties was far in excess of Canadian requirements, and Canada was able to supply the United Kingdom and United States with part of their need.s. Both properties ceased operations during 1944, and, due to an excessive supply of mercury, have not yet reopened. The Pinchi Lake mercury belt lies along a northwest-trending major fault zone called the Pinchi fault zone (Fig. 1). This zone is approximately 150 miles long and varies in width from 200 to 1,000 feet . It forms the northeastern edge of a northwest trending fault belt up to 10 miles or more wide in places. In general the northeastern margin of the Pinchi fault zone represents the contact between closely folded, stratified Permian rock:s on the southwest and Mesozoic formations and Omineca intrusions on the northeast. It seems probable that the fault zone marks the site of major thrust faulting from the southwest and that the Permian rocks moved up with respect to the Mesozoic formations. Intense faulting occurs in the Permian rocks within the fault zone. There the more important faults trend north and northwest, dip steeply west and southwest, and may join a major low-angle thrust fault at depth."

Jan 1, 1954

By S. Sundararajan, J. Brousseau, P. Bocher, M. Galopin, N. Barka

This research is committed to the prediction of the hardness profile produced by induction heating, using a computer-modeling software. The paper presents the simulation of the induction hardening process to analyse the sensitivity of the induction parameters on the hardness profile of a low alloy steel specimen. The developed numerical model includes the coupling effect between electromagnetic and thermal fields, and takes into account the non linear behaviour of the material properties. The study applies an enlightened experimentation method to build the feasible domain of the process and to achieve predictive empirical modeling. The ultimate goal is to replace the trial and error method that is usually used for the development of new parts, by costless experiments with the numerical model. Further development of this approach will lead to the computation of the residual stresses and finally to the assessment of the mechanical properties of the part. The end result will be the ability to shorten the development time and to improve the quality of the hardened part.

Jan 1, 2006

By John Taylor

"The Highvale Mine in Alberta is owned by TransAlta Utilities Corpora/ion and operated by Mana/fa Coal Lid. It is the largest coal mine in Canada and in 1982 supplied 8.6 million 1onnes of sub-bituminous ""B"" coal to TransAlta's Sundance Ceneraling Plan/. Annual produclion is scheduled to increase in 1983 when the firs/ unit of the new Keephil/s Generating Plant comes on stream and is expec/ed to exceed 11 million tonnes by 1985 when the second unit is commissioned. Coal is mined from several pits in a multi-seam operation. Comprehensive maintenance, drainage and environmental programs form a major part of the operation.IntroductionThe Highvale Mine is located eighty kilometres west of Edmonton, Alberta on the south shore of Lake Wabamun (Fig. I). The mine is owned by TransAlta Utilities Corporation (T.A.U.) and is operated by Manalta Coal Ltd. In 1982, 8.6 million tonnes of coal were supplied to T.A.U.'s 2100 MW Sundance Generating Plant, making it the largest producing coal mine in Canada. By 1985, with two 375 MW units on line at T.A. U .'s new Keephills Generating Plant, annual production is estimated to exceed eleven million tonnes. The generating plants accept crushed unwashed coal from the mine via the coal handling plant system conveyor belts. The coal is classified as sub-bituminous ""B"" and has an average heating capacity of 18.6 MJ I kg.HistoryPrior to 1943 only small scale mining took place in the Highvale area. Between 1943 and 1961 two strip mining companies, Mount Royal Collieries and Continental Collieries operated on the present mine site. Both operations excavated coal along the south shore of Lake Wabamun."

Jan 1, 1985

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By J. A. Finch, A. M. Elmahdy

Blending frothers is becoming common in flotation practice apparently enhancing performance. However, there have been no studies to understand the blend mechanism. In this paper, the effect of two frother blends ofF150 (polyglycol) with MIBC or pentanol (both alcohols) on bubble size, gas holdup and froth height is reported. The blends focused on a small addition of the polyglycol to the alcohols as base frother. The tests showed that the bubble size at blend concentration below the critical coalescence concentration (CCC) of the base frother was decreased but was significantly larger above the base CCC. Froth build-up showed a strong synergistic effect.

Jan 1, 2009

By H. Utsunomiya

Most magnesium alloy sheets show low deformability in rolling. Edge cracks and transverse fractures are common difficulties. In addition, rolled sheets show well-developed basal texture <0001>//ND. The texture causes high anisotropy in mechanical properties and low formability in subsequent metal forming. Differential-speed rolling, where the upper and the lower rolls rotate at different speeds, introduces shear deformation through the thickness. Not rolling texture but shear texture evolves in the sheet so that the asymmetric rolling can be a method of texture control. However the primary slip system of the hcp alloy, is basal, the shear texture should be also basal. Differences between the two basal textures, i.e., the rolling texture and the shear texture, have not been understood completely. In this study, conventional (same-speed) rolling and differential-speed rolling have been applied to commercial AZ31B sheets at 623K. Microstructures, textures and mechanical properties of the rolled sheets before/after annealing are compared. It is found that the basal texture is more pronounced by the asymmetric rolling. On the other hand, the asymmetric rolling is effective to decrease the grain size and the planar anisotropy.

Jan 1, 2006

By S. F. Guo, B. W. Zheng, X. L. Huang, S. W. Qi

"The study of mechanical characteristics of rock discontinuities under different shear deformation velocities is an important premise of rock slope dynamic response analysis. According to disposing and calculating the experimental results of previous research about peak shear strength of rock discontinuities under different shear deformation velocity of constant normal loading, the law of influence of shear velocity on the total friction angle is studied. Based on the research results, it can be found that the total friction angle of rock joint specimens varies in the form of negative logarithm with the variation of shear deformation velocity. It’s also indicated that the total friction angle of rock joints decreases with the increase of shear deformation velocity for rock joints of relative strong homogeneity and isotropy. However, the total friction angle of rock joints increases with the increase of shear deformation velocity for rock joints of relative strong heterogeneity and anisotropy and the latter amplitude of increase is less than the former amplitude of decrease. The physical property and microscopic geometry of rock joints play an important effect on the increase or decrease tendency and amplitude variation of total friction angle with the increase of shear deformation velocity.INTRODUCTIONThe rock slope dynamic response is largely restricted by rock discontinuities. Hence the study of dynamic characteristics of rock discontinuities, especially the dynamic shear characteristics is an important premise of rock slope dynamic response analysis (Qi et al., 2007). Seismic load is both dynamic load and cyclic load (Liu et al., 2011). Under the dynamic and cyclic shearing actions of seismic load, the rock slope which is stable under the condition of static load may slide along the rock discontinuities whose shear strength reduce and then the earthquake landslides occur. The strength degradation and deformation mechanism of rock discontinuities under the dynamic and cyclic shearing actions is one of the key problems to be solved in the work of earthquake prevention and control of engineering slope. Based on the above understanding, predecessors conduct some researches which focus on the shear behavior mechanical characteristics of rock joints under cyclic shearing actions (Plesha, 1987; Hutson & Dowding, 1990; Jing et al., 1992, 1993; Huang et al., 1993; Qiu et al., 1993; Homand et al., 2001; Lee et al., 2001; Jafari et al., 2003; Liu et al., 2011, 2013). However, there are a few researches about the mechanical characteristics of rock joints under different shear deformation velocities because of the restriction of shear apparatus. Crawford and Curran (1981) conducted a series of one-way cyclic direct shear tests on four kinds of natural rock joints under different shear deformation velocities varying from 0 to 200 mm/s. The tests showed that at low normal stresses the peak shear strength of soft rock joints exhibited an increase up to a certain velocity, after which it remained essentially constant. For rock joints of intermediate hardness, the peak shear strength was essentially independent of shear deformation velocity; whereas for hard rock joints, the peak shear strength of which showed a significant variation with the shear deformation velocity. Jafari et al. (2003) carried out a series of conventional triaxial tests on artificial rock joints of regular saw-tooth shape with axial loading rate from 0.05 mm/s to 0.4 mm/s."

Jan 1, 2015

By R. H. McCorkell

Radon emanation rates. J. and compositions of materials from the Canadian Certified Reference Materials Project (CCRMP) indicate that the fraction of the Rn produced that escapes, E, is usually 1% to 8% and the 238U decay chain is nearly in secular equilibrium. For some Chinese ore standards, E values are higher than f or the CCRMP materials. Standard ore tailings have 2/oPb concentrations higher than expected from their 226Ra concentrations and Rn escape rates (12 - 34%) . Biological materials have E ˜100%, their ash E ˜0%. Pelletizing ore powders at 20 000 lb/in2 reduces J by only 20 - 40% but only 2% of Rn escapes from pressed Li2B4O7 pellets and 0.01 - 0.04% from fused Na2B4O7 or Li2B4O7 discs. Large, difficult-to-explain random variations in J are observed in some situations but several highly reproducible ways of measuring emanation rates have been found.

Jan 1, 1986

By R. K. Kandasami

"Naturally occurring geomaterials such as sandstone, limestone and other soft rocks, residual soils are composed of a particulates held together through a cohesive matrix, usually composed of argillaceous or siliceous cementing agents. Geo-materials such as these have been reconstituted in the laboratory using ordinary Portland cement in lieu of the naturally occurring cohesive matrix, in addition to using sand particulates. This cohesive frictional granular ensemble is an ideal model material for understanding the mechanical behaviour of transitional geomaterials such as soft rocks. An important consequence of this cohesion that pervades the inter particulate system is the enhanced tensile strength when compared to a purely granular ensemble. The assessment of strength of these soft rocks and cemented sands is often understood in the framework of continuum mechanics, i.e. considering the cemented sand to be a continuum, and performing simple elemental tests such as uniaxial compression or tension tests. A simple model to describe the behaviour of these cemented sands has been to use elements such as springs, sliders, and dashpots in parallel to describe the existence of a cohesive and frictional component of strength (Jiang et al. 2007). In the framework of continuum mechanics, the mechanical response of these cemented sands have been modeled using traditional plasticity theory, for example utilizing variants of the traditional Mohr Coulomb model, Modified cam clay (Sun and Matsuoka 1999) etc. The typical sand models are amended to include the effects of cohesion, as proposed by Lagoia and Nova (1995).The mechanical response of cemented sands is understood to be transitional to the behaviour of a typical particulate assemblage and a quasi-brittle material. However, the effect of length scale in these material systems has not been investigated. This paper presents a series of uniaxial compression experiments conducted on weakly cemented sand specimens of various sizes. The effect of length scale in these weakly cemented sands is investigated through unconfined compression tests."

Jan 1, 2015

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By Lorant B. Geller

Sixteen miners died tragically at the Paymaster gold mine at Timmins, Ontario in February, 1945, when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (Investigations, 1947) aimed at avoiding future disasters of this kind. One consequence was the development, and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the nondestructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990 and 1992, Geller and Kitzinger, 1991, Geller et al., 1993). Since the mid-1990s particular attention was paid to the design and operational results obtained from the computer- controlled portable MagnographJ II wire rope tester (Geller et al., 1995 and 1998). In the present article the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the PermaScanJ testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remotecontrolled instrument described in this paper has now been in operational use for more than 4 years.

May 1, 2003

By A. Nielsen

"The Polaris mining operation (Fig. I) is located on Little Cornwallis Island in the Canadian Arctic, an area with a very limited shipping season and a hostile climate. The operation consists of the underground works, barge-mounted concentrator facilities, concentrate storage and shipping facilities, a personnel accommodation complex and an airstrip.The electrical energy for the operation is provided by four 2.3 MW diesel-generators installed on the barge. The power is distributed through a 4.16 KV system connected directly to the generators and to the large motors. All other loads are supplied at 600 V or 120 V.The power plant has been designed as a Total Energy System with maximum energy efficiency and thus designed for maximum heat recovery. The waste heat recovered on a year &apos;round basis is expected to be sufficient for the process heating and drying as well as the space heating for offices and accommodations. The engine cooling system consists of two glycol-water loops, a "" cold"" loop for charge air and lube oil cooling and a ""warm"" loop for jacket water cooling. Each loop is complete with heat exchangers f or heat recovery and out-door forced air radiators to dispose of excess heat. A water loop in the concentrator area transfers the heat from the jacket water loop and the exhaust gas boiler to the space heating equipment, the process and the heating system for the accommodations. Part of the exhaust gas is diverted to the concentrate dryers.IntroductionThe Polaris Mine is a highly mechanized, trackless mine with access through a decline. Drill equipment is electrically powered to minimize fumes and heat. Dry development and production drilling eliminates the need for an underground water supply system.The concentrator, power generators, work shops and auxiliary facilities are located on a barge which is beached in a prepared berth on the shore of Crozier Strait. Oil storage tanks, concentrate storage and accommodation buildings are built on shore. The concentrate storage building ha s a 12-month capacity and is fed from the concentrator by a conveyor system.The accommodation building houses up to 240 people, includes administration office, dining and recreation facilities. The complex is housed in on e interconnected building with public use areas alternating with accommodation units.At full production annual concentrate shipments will amount to about 220,000 wet tonnes. This will be accommodated by about 8 shipments during the regular shipping period-August 15 to October 15. Re-supply of general cargo and fuel will be carried out annually in about 3 shipments within the same period."

Jan 1, 1984

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

By S. Komar Kawatra, Youlian Zhou, Joseph A. Halt

"Bentonite clay has been the most common binder for iron ore pellets. Although bentonite increases pellet strength and durability, it has several disadvantages. For example, its use increases the cost of pellets and decreases pellet purity due to its composition and the higher levels of flux required to meet basicity limits. Several new types of binders have been proposed to replace clay. The binders include starch, modified humic acid (MHA), and dispersants. These binders were used to pelletize a magnetite concentrate from the United States. Typical doses of each binder type were 0.05-0.1 % starch, 0.5-0.75 % MHA, and 0.05 % dispersant. At these doses, the pellets exceeded the minimum recommended values for wet drop, dry compression strength, and fired compression strength. Pellets made with the MHA and dispersants had the lowest abrasion rates of the new binders, and were comparable to pellets made with bentonite clay. In this paper, we compare the new binders, considering pellet quality and the advantages and disadvantages of each binder type.INTRODUCTIONIron ore pelletizers need binders in order to make good quality iron ore pellets. The typical binder is bentonite clay, an alumino-silicate material. Bentonite increases the ballability and strength of iron ore concentrates, but reduces pellet iron grade and reducibility. As high quality bentonites can be expensive to ship, low quality bentonites are often used at significantly higher doses – this reduces iron grade and reducibility even further. Thus, several new types of binders have been proposed to replace bentonite clay.In this paper, we present several new binders for iron ore pellets: starch and modified humic acid (MHA). These have been tested alone and in mixtures with dispersants, or else with bentonite clay. Starch, MHA and their mixtures are briefly described below."

Jan 1, 2016

By A. Kapoor

Gold mill effluents contain toxic pollutants such as cyanide (CN), thiocyanate (CNS), ammonia (NH4-N), and a variety of toxic metals. Various practical and economical technologies are in use for the removal of CN and toxic metals from gold mill effluents, however, the removal of CNS and NH4-N is challenging. The presence of CNS and NH4-N may make effluents toxic to aquatic life. The new Canadian Metal Mining Effluent Regulations will require mine effluents to be nontoxic. As a result, there is a need to develop practical and economical technology for CNS and NH4-N removal. The Mine Effluents Program in the Environment Group is presently evaluating biotechnology processes for the removal of CNS and NH4-N from gold mill effluents. The processes being evaluated are attached growth systems such as a Rotating Biological Contactor (RBC) and completely mixed suspended growth systems such as a Sequencing Batch Reactor (SBR) operating in a batch mode. The research to date at MMSL has shown that the RBC is very effective in removing CNS and NH4-N from simulated effluents. The NH4-N removal project showed that the RBC is capable of removing 0.8 g NH4-N/m2 of RBC disk area per day at an average temperature of 4.5 oC and hydraulic loading rate of 0.02 m3/m2/d. The RBC was also found to be very effective in removing CNS (feed = 200 mg/L and effluent < 1 mg/L) at 8 oC and a hydraulic loading rate of 0.02 m3/m2/d. The SBR was effective in removing CNS and NH4-N (generated from CNS degradation) at SBR operating conditions of two-12 h treatment cycles and a temperature of 12 oC. The end product of CNS and NH4-N oxidation was NO3-N, which is relatively non-toxic.

Nov 1, 2002

By P. Molera

"In Catalonia, between the 10th century and 1878, some installations were developed which at first were called ""factories"" and later ""fargas"", since they manufactured iron and steel of low carbon content. Because of its excellent quality, the fame of this metal spread from Catalonia to many countries. Fargas were started in Corsica, the Low Countries, Germany, Oriental India, Madagascar, Finland and along the rivers Orinoco and Mississippi among others. The extractive process used in these fargas has passed into history as the ""Catalan Farga Process"", ""Catalan Process"", or just ""Farga Catalana"". With this technology, raw material was obtained for the fabrication of tools, nails, weapons, grilles, etc. to supply the national and export markets. Aside from meteorites and native iron, found as metallic nodules in basalts in Greenland and Palestine, the ancient civilizations, which had no means to reach the fusion temperature of iron (1535°C), obtained iron by a direct process. Similar processes were used until quite recently (1930s) by certain tribes in Central Africa; holes in the ground were filled with iron ore and coal, and combustion encouraged by blowing air by mouth or with bellows made of animal skins. Thus without melting the iron it is possible to reduce the mineral and obtain a porous and impure metallic mass, which is purified on forging by mechanical squeezing. With a process very likely similar, the famous column at Dehli weighing 6.4 m.t. was built about 300 B.C."

Jan 1, 1999

By Marco Quirion

The Daniel-Johnson dam, formerly named Manicouagan-5 (Manic-5), is located 800 km northeast of Montreal (Quebec) in Canada. This is the largest multiple-arch concrete dam in the world consisting in 13 arches and 14 buttresses. Since its construction in 1969, various type of cracks have appeared on both downstream and upstream faces of almost all the arches of this concrete dam. As a part of the Daniel- Johnson’s dam safety assessment program, Hydro-Québec is currently performing structural analysis of the dam with advanced numerical models to better understand and predict the dam behaviour. Because the buttresses transmit all the arch loads to the rock mass, determination of the properties of the dam foundation should not be neglected in dam global safety analysis and also to insure that reliable input parameters are used in the dam numerical simulations. This paper summarizes the past and the more recent investigations of this foundation used to assess its safety and stability. Moreover, the use of rock mass classification to estimate the deformation modulus, based on empirical equations, gives values in the range of 30 to 40 GPa that are higher than expected values. Using those values in the numerical simulations for dam structural analysis gives an excellent correlation with displacements monitoring of the buttresses.

Jan 1, 2015

By J. W. Coetzee, H. E. Deist

Carbon-in-pulp (CIP) and Carbon-in-leach (CIL) processes are used extensively in the gold mining sector to recover aurocyanide from solution. This paper discusses the modelling of these operations, using various simplifying assumptions, in order to simulate the effect of changing operating conditions on the dynamics of the system. It is assumed that the adsorption and leaching rates are a function of concentration difference between the source phase and recipient phase. The simulation was set up using Matlab&apos;s Simulink interface. Plant variables are solved using a medium scale Newtonian search algorithm in Matlab, where the differences between the actual and predicted plant outputs are minimized on a continuous time-line.

Jan 1, 2005