Search Documents

By F. Mercier-Langevin

ABSTRACT; Agnico-Eagle’s LaRonde mine is one of the deepest mines in Canada. Ground conditions in the deeper levels can be very challenging, ranging from hard and brittle to soft and squeezing. As a result, rock mechanics and ground control practices have had to evolve considerably to accommodate progressively deeper mining activities. This paper focuses on the deeper levels of mines and how the difficult ground conditions encountered there have influenced the mining strategy. The first section examines ground control practices and support systems in highly stressed, poor quality rock. The evolution of level layout is also presented. Finally, improvements in stope sequencing are reviewed.

Jan 1, 2010

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By André Chagnon, Héroux. Yvon

"Résumé - Cette étude porte sur l'altération de la matière organique et des argiles dans les boues carbonatés dévoniennes du facies ""F' de la Formation de Pine Point et ses équivalents stratigraphiques la Formation d'Evie et l'unité bitumineuse de la base de la Fonnation de Hom River. La matière organique se compose principalement de bituré solide et de quelques fragments de fossiles (organaclastes). La majorité des échantillons ne renfement que de l'illite et des inter-stratifiées illite/smectite.Si on compare les températures d'homogénéisation (Th = 100°C) des inclusions fluides de la sphalérite et des dolomites associées a la minéralisation aux températures estimées à partir de la réflectance de la collinite (84°C à 117°C), l'on ne peut pas conclure à la présence d'une anomalie thermique dans le district minier de Pine Point. De plus, la réflectance des organoclastes n'est pas plus élevée dans le district minier de Pine Point que dans les localités plus éloignées des gites. L'analyse des minéraux argileux conduit à la même conclusion: aucune anomalie thermique n'est décelable dans les unités échantillonnées à l'intérieur du district minier de Pine Point quelque soit l'indicateur utilisé.La kaolinite et la matière organique altérée, affichant des valeurs anomales de sa réflectance, se trouve essentiellement en présence de soufre et de sulfures. Cela suggère une origine authigène de la kaolinite et une altération de la matière organique reliées au phénomènes de minéralisation.Abstract - The alteration of organic matter and clays is studied in the Devonian Pine Point Formation carbonate muds, ""F"" facies, and its lateral equivalents the Evie Formation and the bituminous unit at the base of the Hom River Formation. The organic matter is mainly composed of solid bitumen with few fossil fragments (organoclasts). Most samples contain only illite and mixed layer illite/smectite.If we compare the Th (100°C) from fluid inclusions of sphalerite and dolomites associated with mineralization to the temperatures calculated from the reflectance (Ro) of the collinite (84°C to 117°C), we cannot detect a thermal anomaly in the Pine Point mining district. This result is based on the reflectance values of organoclasts from the mining district that are not higher than those reflectance values measured on organic matter (OM) away from the ore deposit. A similar conclusion is reached from the clay study: none of the parameters used allow us to identify a thermal anomaly in the samples from the mining district.The kaolinite and the altered OM showing anomalous Ro values mainly occur with sulfides and sulfur. This association suggests an authigenic origin for the kaolinite and an alteration of the OM due to the mineralization events."

Jan 1, 1994

By Roger Davieds

FACT: a company?s profitability (or loss) is directly related to the efficiency and effectiveness of its maintenance operation. Fact: in order to contribute in a positive manner, maintenance must understand what its true purpose is in the organization. It is easy to say our main purpose is to increase: ?equipment uptime ?OEE ?asset life cycle We all understand this; so does management.

May 1, 2010

By A. Bois-Brochu, G. Morin, G. Marin, M. C. Parr, J. Carignan

The presence of an alpha case on titanium parts produced by investment casting is problematic and has to be eliminated. The traditional techniques for the evaluation of its thickness are metallographic measurements and micro-hardness profiles. To obtain a better understanding of how the alpha case is formed with the underlying objective of limiting its depth, the present study proposes to characterize the microstructure and the chemical composition of the alpha case. Electron microprobe analyzer (EMPA) linescans were used to quantify the oxygen and substitutional elements that come from the mould and promote the alpha case formation. The chemical profiles were correlated with metallographic and microhardness measurements. For microstructure, optical microscopy (etched and polarized light analysis) was used. For phase analysis, samples were mechanically polished step by step and analysed using X-ray diffraction and optical microscopy. Furthermore, surface analysis techniques such as XPS and Auger Microscopy were evaluated but results were found to be inconclusive because the formation of the oxide layer was faster than its ablation and the matrix could thus not be analysed. The alpha case was observed on a Ti-6Al-4V step block casting.

Jan 1, 2014

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By A. Dolatmoradi

Nanocrystalline structure formations produced by severe plastic deformation in Fe-0.15C with initial ferritic-pearlitic and IF steel with ferritic microstructures have been studied through microstructural observation and microhardness measurements. It was found that the nanocrystalline region first forms near the surface of samples due to localized severe deformation. It was also observed that the nanocrystallization rate of Fe-0.15C and IF steels and the deformed layer thickness in these two materials are different with similar milling conditions. The crystallite size and structural evolution of the samples during milling was studied by employing XRD and SEM.

Jan 1, 2010

By Marc Boyer

Modern civilization, modern industry, and modern standards of living, bring into, sharp relief the present-day essentiality of metals .and minerals, and the wide and diversified use which is made of them. Any attempt, therefore, to appraise the international situation today must take into consideration the metal and mineral resources of the world. If, as some believe, the world is divided into two distinct ideologies of political belief, one unalterably opposed to the other, so that armed conflict is unavoidable, then the question of national strength in mineral resources becomes of paramount importance. If, however, it is possible to avoid war by raising the standard of living in the underdeveloped ?areas of the world, thus ensuring all peoples everywhere against the dread spectres of starvation and disease, then the development of the world's mineral resources assumes even greater importance. Today it is difficult to realize that, prior to the industrial revolution in Great Britain, only a few of the metals and minerals now in common use entered into the everyday life of the people. !iron and steel, copper, lead, tin, and zinc, usually in .their unalloyed forms, along with the more common industrial minerals, were those most widely used, and then only in limited amount. With the advance of technology in metallurgy and in fabricating skills, the list of commercial metals and minerals has expanded until today they number more than eighty.

Jan 1, 1951

By J. Bruce See

INTRODUCTION This symposium at Cu 2019 has been organised to honour and celebrate the career and achievements of Dr Phillip John Mackey, an internationally recognised expert in the production of non-ferrous metals, especially copper and nickel smelting and refining. Phillip was born in Epping, a suburb of Sydney, New South Wales, Australia on 19 April 1941 and is one of 4 children of Gilbert and Philomena (nee Bartlett) Mackey. After completing Primary School in Epping, he attended Marist Brothers High School in Eastwood, Sydney and graduated in 1957 as the Dux of the School. Phillip’s father, being on the staff of the Sydney Technical College, in Ultimo, Sydney had the opportunity in the early 1950s to meet the late Professor Sir Rupert Myers, Foundation Professor of the School of Metallurgy at the New South Wales University of Technology (later called the University of New South Wales or UNSW). Gilbert Mackey was impressed by the new young Professor of Metallurgy and encouraged his son to study metallurgy - at the time an expanding industry in post-war Australia. EDUCATION AT THE UNIVERSITY OF NEW SOUTH WALES Phillip commenced at UNSW in 1958, graduating with honours in 1963. His undergraduate education and training included a few years of part-time study while working at British Motor Corporation on sheet metal forming of car bodies. At University Phillip developed his talent for teamwork. He was a contributing writer to the University newspaper, Secretary of the UNSW Students’ Union and was active in the UNSW Metallurgical Society and co-editor in 1963 of “Metallurgical Review,” the annual journal of the UNSW Metallurgical Society. His diverse interests and curiosity about the world around him were likely nourished while at University. Upon completing his Bachelor’s degree, Phillip was awarded a Commonwealth of Australia Postgraduate Research Scholarship. He began his PhD in 1964 on the thesis topic “Studies in Heat Transfer between Dispersed Liquid Metals and Gaseous Atmospheres” working under the supervision of then Associate Professor Noel Warner, an outstanding Professor at the University. Professor Warner is now an Emeritus Professor at the University of Birmingham and is internationally respected for his pioneering theoretical and practical work on established and innovative smelting processes.

Jan 1, 2019

By Roger M. Nendick

"IntroductionThe stages of development for bringing a mill into production demand that a flowsheet for the process be developed at an early stage. Detailed engineering of the mill may then proceed without duplication of engineering effort on alternative processes. In the case of gold and silver mills, several process alternatives exist which must be evaluated before the flowsheet is finally fixed. The recently developed Carbon-in-Pulp process has added to this choice.Clearly, the major factor in determining the most suitable process is the amenability of the particular ore to a given treatment. Other factors that will also influence the choice are location, climate, power and water supplies, and available capital.Gold and silver milling processes can be divided into three main types:Gravity Concentration;Flotation;Cyanidation.Combinations of the three are frequently used; i.e. flotation followed by cyanidation of the concentrate, or gravity concentration in the grinding circuit with cyanidation of the classifier overflow. The following are the salient advantages and disadvantages of the three main alternatives.Gravity ConcentrationGravity concentration is suitable for free-milling gold ores, i.e. ores in which the gold is relatively coarse and free from sulphides. It should be noted that just because an ore is high grade, it is not necessarily free milling.Gravity concentration methods include jigs, shaking tables, spirals and more recently Reichert cone concentrators. All methods exploit the density difference between gold, which has a specific gravity greater than 15, depending on how it is alloyed, and the gangue, which usually has a specific gravity range of 2.7 to 3.5.A concentrate grade of several hundred ounces per ton might be produced, but recoveries by gravity alone are generally low in comparison to other methods. For this reason, gravity circuits are usually used in combination with flotation or cyanidation circuits."

Jan 1, 1983

By Roland Froidevaux

"The main object of ore reserve classification is to assess the reliability of an ore reserve estimate. Because traditional classification schemes fail to provide a means of calculating this reliability, the terms 'proven "" 'probable' and 'possible ' ore were introduced as an attempt to qualify it.Geostatistics, on its part, allows the quantification of the precision of any ore estimate and thus appears as an appropriate tool for ore reserve classification.However, the problem of fixing quantitative boundaries for ore classes remains. In order to be meaningful, ore class limits based on the degree of reliability should be customized to the commodity, and the type and size of the deposit. In addition, the precision of an ore estimate will be affected by the cut-off grade and the size of selective mining units.IntroductionPrimarily, ore reserve classification should be seen as a communication tool between the geologist and the mining engineer on one hand and the management and policy maker on the other. By classifying ore reserves, the geologist tries to answer the very fundamental question: ""What quantity of metal is there in the ground and how sure am I that it really exists?""The difficult y of quantifying the degree of reliability of reserves has led to the creation of a large suite of terms and definitions, with almost every mining company having its own set of definition standards. As lower-grade deposits are brought into production, the margin of tolerable error in estimates of the grade and tonnage is becoming much narrower. Consequently, the need for unequivocal definition of the reliability of ore reserves is increasingly acute. Most of the generally accepted systems of classification, however, describe the reliability of reserves in qualitative, rather than quantitative, terms."

Jan 1, 1982

By H. McLeod

Introduction In the period from 1939 to the present, Canada has experienced a remarkable industrial expansion, rising to probably seventh in rank amongst world countries. In the early part of this period, the desperate need for military supplies unloosed tremendous amounts of capital for building new factories and for expanding and converting existing facilities. Mines, factories, and other divisions of the industrial economy bent every energy toward greater and greater output. The result was an 80 per cent increase in the volume of the nation's production within a period of four years, a truly remarkable accomplishment and one in which the mining industry had a very vital part. After the critical year, 1944, the tempo of industry eased off a bit, dropping approximately 20 per cent by 1946. At this time the prospects or post-war industry were clouded by monetary and political chaos in overseas countries, by trade restrictions, and by market uncertainties. There was, of course, a pent-up demand, both at home and abroad, for civilian goods that had been curtailed during the war and for capital equipment that had been destroyed. In the midst of this world-wide uncertainty, if anyone had ventured to predict that by the end of 1950 Canada's industrial output would be back to the 1944 level and humming along at nearly twice the best pre-war pace, he would have been considered rash indeed. Yet this has been the case.

Jan 1, 1951

By Adrianus (Adrian) Halim, Tomas Bolsöy, Stina Klemo

"This paper describes the ventilation system used in underground hard rock mines in Sweden and Finland, which is very different than the system used in other major mining countries such as Australia, Canada, South Africa, and USA. The system utilizes auxiliary fans with Variable Speed Drive to distribute primary airflow to working levels instead of regulators that are commonly used in other countries. Descriptions about Ventilation on Demand in this system and ventilation regulations in Sweden and Finland are presented in this paper. This paper also quantifies a comparison between the Nordic and the system used in other countries. KEYWORDS Auxiliary fan, Regulation, Ventilation on demand (VOD), Variable speed drive (VSD) INTRODUCTION The primary objective of an underground mine ventilation system is to provide sufficient airflow to dilute atmospheric contaminants that are produced by mining activities. Typically, a mine ventilation system consists of one to four primary fans, regulators to control primary airflow distribution to levels or panels, and auxiliary fans that distribute airflow to dead-end workings via ducts. Depending on circuit geometry, underground booster fans are sometimes used. This system is widely employed in many countries such as Australia, Canada, USA, United Kingdom, and South Africa. However, mines in Nordic countries such as in Sweden and Finland employ a different system, in which auxiliary fans instead of regulators are used to control primary airflow distribution, as well as distributing airflow to dead-end workings. This paper describes the general layout of Nordic ventilation system, its VOD and heating system, its comparison with the system that is widely used in other countries which is referred as “Non-Nordic ventilation system” in this paper, and the current ventilation regulations in Sweden and Finland. The comparison was quantified by doing simulations using Ventsim Design 5 software. DESCRIPTION OF NORDIC VENTILATION SYSTEM General System Layout Figure 1 shows a schematic of typical ventilation system used in Swedish and Finnish mines. The schematic was drawn by Franzen, Myran, Larsson, and Rustan from Stiftelsen bergteknik forskning (Swedish Rock Engineering Research Foundation) and the English translation is written next to the Swedish terminologies. The system is generally a push-pull system. None of Swedish and Finnish mines use exhaust system. As shown in Figure 1, the primary airflow is distributed to levels by auxiliary fans that are bolted to a bulkhead located in the access to intake raise/shaft. These intake fans are attached to ventilation ducts that distribute airflow to all working faces. The exhaust auxiliary fans, which are not attached to any ducts and also are bolted to a bulkhead located in the access to exhaust raise/shaft, then flow the exhaust airflow into the exhaust shaft. A small quantity of this exhaust air is directed into the ramp, which acts as another main exhaust airway. The deepest level is also equipped with booster fan(s) that draw air from the intake shaft/raise and direct it into the ramp to provide fresh air in the ramp. There is no free split in this system. Figure 2 shows a schematic of a level ventilation layout in the Nordic system. Figure 3 shows a photo of these auxiliary fans."

Jan 1, 2019

By N. J. Bunce, B. Vollick, A. F. Souza, D. Bejan, P. Maharaj, C. Shamshoom

"Copper electrodeposition from synthetic and authentic acid mine drainage (AMD) is inhibited by ferric iron (Fe(III)), through re-oxidation of copper. Polarization to –2.5 V versus standard hydrogen electrode prevents the dissolution of predeposited copper from the cathode. Above pH 1, copper deposition is independent of Fe(III) concentration to approximately 25 g/L. Fe(III) is reduced to ferrous iron (Fe(II)), with a high combined current efficiency for iron and copper reduction. In a divided cell, the conversion of Fe(III) to Fe(II) is almost quantitative, with efficient transfer of acidity from catholyte to anolyte. Prospects for developing electrochemical technology for complete remediation of AMD are discussed.RÉSUMÉ En raison de la réoxydation du cuivre, le fer ferrique (Fe(III)) nuit à l’électrodéposition du cuivre à partir de drainage minier acide (DMA) véritable et synthétique. Une polarisation à -2,5 V par rapport à l’électrode standard d’hydrogène empêche la dissolution du cuivre déjà déposé de la cathode. À un pH supérieur à 1, la déposition du cuivre est indépendante de la concentration en Fe(III) jusqu’à environ 25 g/L. Le fer ferrique est réduit en fer ferreux (Fe(II)) avec une efficacité combinée élevée pour la réduction du fer et du cuivre. Dans une cellule divisée, la conversion de Fe(III) en Fe(II) est près de la quantité théorique, avec un transfert efficient de l’acidité de catholyte à anolyte. Les perspectives de développement d’une technologie électrochimique pour la remédiation complète du DMA sont discutées."

Jan 1, 2016

By S. Esmaeili

The yield strength model developed by Esmaeili, Lloyd and Poole [1] has been adapted to model isothermal aging in Cu-containing AA6xxx alloys, with (a) a moderate and (b) a very low Cu content in the solution-treated, as-quenched, condition, Isothermal calorimetry has been used to analyze the kinetics of precipitation in these alloys, While the kinetic parameters for the low Cu alloy has been derived from the present experiments, the previously determined kinetic parameters for the high Cu alloy AA6111 has been used to model the precipitation kinetics in the moderate Cu alloy. The age hardening responses of both alloys have been well predicted by the model.

Jan 1, 2005

By Abhinav Karanam, Lukas Bichler

Yttria Stabilized Zirconia (YSZ) is a promising thermal insulator for high temperature environments due to its thermal stability and chemical inertness. As was demonstrated with other technical ceramics (e.g., Alumina), addition of Single-Wall Carbon Nanotubes (CNTs) to a ceramic matrix may significantly enhance the mechanical properties of the composite ceramic. In this work, 8 mol% YSZ with 0.2, 0.5 and 1wt% CNTs composites were prepared via Spark Plasma Sintering process. The densification, Vicker’s microhardness, specific gravity and microstructure evolution of the composites were investigated. The results suggest that the addition of up to 1wt% CNTs to YSZ yielded optimal combination of the studied properties. At higher addition levels, the specific gravity decreased and clustering of CNTs occurred, leading to poor densification and a relative loss of performance.

Jan 1, 2014

By D. Racicot, T. Hanel, E. H. Chown

Over thirty plutons in the Chibougamau-Desmaraisville belt were examined briefly in the field and sampled, in addition to the few masses that have been studied in detail. The survey indicates that the intrusions may be conveniently grouped in four main categories, based on their time of intrusion. These are; remobilized basement domes, pre-kinematic intrusions, syn-kinematic intrusions and postkinematic intrusions. Basement domes, as exemplified by the Lappa rent Massif, are composed of migmatized tonalite-diorite gneiss that has undergone at least two periods of mafic dyke intrusion and at least three major deformational periods. The rise of the basement domes was accompanied by extensive mylonitization and the intrusion of syn-tectonic plutons. Pre-kinematic plutons, such the Chibougamau pluton, are diori te-tonalite in composition, and were intruded into the supracrustal pile and partly eroded before the main deformation of the belt. Syn-kinematic plutons occur principally as marginal intrusions bordering the belt (Barlow), or as discrete intrusions along structural highs (La Dauversiere), and are either hornblende monzodiorite or tonalite in composition. Post-kinematic plutons, such as Muscocho, are principally granodiorite and often porphyritic intrusions locally deforming the enclosing rocks. The close relationship between mineralization and high-level intrusions such as the pre-kinematic and some of the post-kinematic plutons is discussed.

Jan 1, 1984

By Michael DeLallo

Clean Coal Technology (CCT) ?Technologies designed to enhance both the efficiency and the environmental acceptability of coal extraction, preparation and use?. These technologies reduce emissions, reduce wastes, and increase the amount of energy gained form each ton of coal extracted and converted into energy. ?? Carbon Capture and Sequestration are an integral part of CCT either as constructed or on a future retrofit basis.

May 1, 2008

By Chris Twigge-Molecey

Demand for metals will continue to grow as global population numbers and prosperity levels steadily increase. Consequently, there will continue to be a need to design and construct new metallurgical plants. Business success in general requires projects to be financially successful and return appropriate value to their owners. However, in the metals industry, private and public sector financing sources have become very sensitive to the perceived inability of projects to contain costs and meet other business objectives. Thus, the capital for projects has become more difficult and expensive to obtain. It is instructive to note that Ernst and Young (2011) identified that: “Delivery of predictable project results bestows competitive advantage and market confidence to those corporations who successfully instill this discipline”. The implication for future projects is that they must be systematically developed to minimize perceived risks—and more importantly—to demonstrate that the risks are managed to achieve the business case. Then, provided that the project has been developed in a well-structured way, project success can again be defined as a project with: a final cost within 10% of the budget approved at the end of FEL3, when the project is properly defined and the permit conditions are agreed upon; a start-up date within three months of the definitive, scheduled startup date; production levels at 85% of design capacity within a year of starting commercial operation; production meeting the target environmental restrictions; and with zero lost time accidents during construction and startup. The plant design is one of many integrated activities required to achieve these objectives. This book represents a valuable link between the existing engineering literature that encompasses a wide range of engineering fundamental textbooks and design manuals and the project management literature such as the Project Management Body of Knowledge, or PMBOK® (Project Management Institute, 2014). It is evident throughout this book, that the design team is a small but essential part of a much larger project team comprising the project management, construction management, and construction contractor staff. Design activities must be regarded and managed as part of the integrated whole, with two fundamental links throughout the design process:

Jan 1, 2015

By Joanne G. Petrini

ISO 26000 Unique Process Unique Personality ?Almost 10 years in the making ?What type of standard is this? Different type of ISO Standard ISO 26000 Structure and Substance ?Principles ?Core Subjects ?Implementation Guidance ISO 26000 Impact ?Same old, same old? ?So Is there really anything NEW? ?Should I care??

May 1, 2011