Search Documents

By J. Fellowes, Z. Liang, J. Robson, M. Kenyon

"Dispersoids play a significant role in the recrystallization and texture development for wrought Al-Mg-Si (6xxx series) alloys by inhibiting grain boundary motion. It is therefore important to understand the precipitation kinetics of such particles. It is the additions of Mn and Cr in Al-Mg-Si based systems that can lead to dispersoid phases being formed. These phases are currently thought to nucleate on ß’-Mg2Si via an intermediate semi-coherent precipitate. Scanning transmission electron microscopy (STEM) has been conducted to study the precipitation of a-Al(CrFe)Si and a’-AlCrSi dispersoids. Corresponding electron dispersive spectroscopy (EDS) has been used to distinguish the dispersoids. The volume fraction and size distribution of dispersoids has been measured as a function of distance across a grain. Electron probe microanalysis (EPMA) has been conducted to study the inhomogeneity of elements in the cast structure and the effect on dispersoid precipitation. Dispersoid free regions have been observed in the microstructure correlating to regions depleted in the dispersoid forming elements.INTRODUCTION Al-Mg-Si (6xxx series) based alloys are increasingly being used in the automotive industry. The primary reason is to reduce the weight of vehicles, resulting in a reduction of CO2 emissions and increased fuel efficiency. The demand for 6xxx series is predicted to increase over the coming decade. Due to the high cost and CO2 emissions produced by raw extraction of aluminium, close loop recycling of these alloys becomes a more important process. However recycling of automotive alloys can be difficult due to pick up of impurity elements such as Mn, Cr and Fe. The addition of these elements can form dispersoid particles during early heat treatment processes. Although a controlled population of dispersoids is necessary to control the grain structure during thermo-mechanical processing, a significant change to the dispersoid population due to a composition change could profoundly influence the final microstructure, affecting the final properties of the material. More research is required on the precipitation and effect of additional minor alloying elements; in order to increase the 6xxx series alloys recyclability."

Jan 1, 2018

By Du Xinfeng

The resource quantity of the low rank coalbed methane (CBM) accounts for 47% of the total resource quantity of CBM in China. Compared with the exploration and development of the high rank CBM in Qinshui Basin, China and the low rank CBM in Powder River Basin, USA and Albert Basin, Canada, the exploration and development of the low rank CBM are still in the initial test stage. In this paper, on the basis of analyzing the mining geological conditions such as that the Huanglong Jurassic Coalfield is largely situated in the hills and gullies zones, and the coal reservoir has the features such as the low metamorphic degree, large coal seam thickness, simple coal matrix texture, high permeability and small CBM content and so on, it discusses the key technologies such as the development pattern of CBM, well location arrangement, drilling and well completion technology and fracturing technology and so on. It indicates that the underbalanced drilling and the cavity well completion based on the reservoir protection will be the development directions of the CBM development technology in this area.

Aug 1, 2013

By Tim Watson

Andacollo Hypogene Project ?Overview Project description: Sulphide copper concentrator Throughput:55,000 tpd Location: Approximately 50 km from La Serena Elevation: Approximately 1,000 m ASL Start feasibility study: July 2005 Start of construction: May 2007 Construction completion: December 2009 Final cost(1,2,3):435 Million US $ (1) Excludes third party costs, 220 kV power line (2) Cost is based on a Chilean Peso to US Dollar foreign exchange rate of 535 to 1 (3) Does not include US$40.3 million for the Elqui River Pipeline Project or US$8.0 million for the stock pile cover

May 1, 2010

By A. Saki, P. Gebski, W. Ying

Industrial smelting furnaces are subjected to significant structural changes and deterioration caused by the conditions under which they operate. The current methods for the structural assessment of furnaces include visual inspections, analysis of thermal data, acousto ultrasonic-echo (AU-E) of the refractory lining and surveying of the key structural elements. Acoustic Emission (AE) non-destructive testing (NDT) technique has proven its capabilities for continuous monitoring of industrial installations and structures. Recently, Hatch Ltd. has been successful in applying acoustic emission for monitoring furnace tapblocks, and expanding the scope of the acoustic emission monitoring to the structural integrity of the entire furnace. The capability of detecting emissions related to the fracture development in the furnace shell, movement of the refractory, electrode arcing, combined with efficient source location algorithms makes an acoustic emission system a comprehensive tool for the real-time furnace integrity monitoring. In this paper the concept of such state of the art system for structural integrity assessment is presented. The initial results of the acoustic emission monitoring together with data analysis techniques are discussed.

Jan 1, 2011

By T. Krumins, L. Zunti, R. Frischmuth

Mercury is known to occur in sulphide-bearing refractory gold deposits in the form of sulphide minerals or elemental inclusions. These deposits typically require an oxidative pre-treatment process, such as pressure oxidation or roasting, to achieve economic gold recovery. However, these processes also have the potential to liberate mercury, a portion of which may then be released to the environment through gaseous emissions. Mercury emissions from mine processing operations have been of particular interest in recent years, as governments impose lower emission targets and organizations adopt better industry practices to reduce the environmental and health aspects of releasing mercury into the environment. This paper describes various mercury removal technologies with respect to pressure oxidation gas handling circuits, with a focus on key design variables and technology selection criteria.

Jan 1, 2014

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015

By N. Erarslan, M. Ghamgosar

The size of rock fragments depends on the nature of the loading applied the strength of the minerals and the texture of the rock. Research in the literature demonstrates that there is a distinct difference in the rock fracturing process for static and cyclic loading. The tensile strength of brittle rocks is also one of the most significant parameters influencing the rock fracturing process and the propagation of micro-fractures on the crushing, blasting and cutting of rock. The Brazilian indirect tensile test, one of the methods approved by the International Society for Rock Mechanics (ISRM), has been used to determine rock fracture behaviour under different cyclic loading modes. In this study, the dimensions of Brisbane Tuff specimens have been selected according to the method outlined by the ISRM. The main aim of this study is to evaluate the effect of cyclic loading amplitude and frequency on the Fracture Process Zone (FPZ) at the micro-, meso- and macro-scales. The post-failure behaviour of the Brisbane Tuff specimens was obtained under cyclic loading with frequencies varied from 1 to 10 Hz. The amplitude was varied from 10% of Ultimate Tensile Strength (UTS) up to 80% UTS. Laboratory investigations of rock fragment size revealed that different loading frequencies and amplitudes produce different FPZ dimensions. Multivariate Analysis of Variance (MANOVA) results demonstrated that the FPZ dimension is relatively sensitive to the frequency change. Fragment size analysis showed that the FPZ is a consequence of the initiation, propagation and coalescence of micro-fractures and depends on the nature of the loading. Laboratory evidence showed that the FPZ dimension, for the cyclic tests performed on Brisbane tuff, is ranged from 0.07 to 20 mm. The achievement of this study highlights a key finding in the understanding of fracture patterns and propagation models in the FPZ under cyclic loading, which is the dominate mechanical action in the oscillator disc cutter (ODC).

Jan 1, 2015

By Bryan Wilson

Background ?Nickel Rim South Mine started production ramp-up in Q2, 2009. ?The main dewatering pumps were put into use in August 2009. ?3 Feluwa?multisafe?positive displacement pumps ?1700m single lift pumping ?Reliability has been an issue due to the amount of slimes and fibers (from shotcrete) at the pumps. ?Critiqued internal dewatering system to solve some issues we were having with our sumps Findings 1.Much of the final dewatering system was not in place. a)Temporary pain. Difficult to say something is not working when the system was not yet in place as per design. b)Not enough capacity to handle slimes within the system. 2.Need to address issues with the final design: a)Ongoing costs: The end design has operating costs of $2.5 million b)Scoops in Sumps: The end design relies on scoops to be used for cleaning the sumps c)Slimes Recovery: The system mixes 3 different products in the sumps along with the fibers d)Pump repair costs: The existing Tsurumi pumps are too light duty for our slimes

Nov 1, 2011

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By R. R. Song, Q. Li, H. Xing, X. C. Wei

Geomechanical modelling of fault stability is an important part of CO2 capture and storage (CCS) research program to ensure its viability and long-term safety. Storage of CO2 in deep subsurface reservoirs requires estimates of sustainable fluid pressures that will not induce fracturing or fault reactivation which could cause fault slip. More importantly, fault slip gives rise to seismic waves, which inflict severe damage to the cap rock of the reservoirs and may result in leakage pathways for the buoyant plume and thus compromise the integrity of seal formations. In this study, we generated a numerical model tuned towards conditions usually encountered in the Shenhua CCS demonstration project in Ordos basin. In particular, with the purpose of evaluating the sensitivity of the parameters as well as their relationships with the moment magnitude of the seismicity, a variance-based sensitivity analysis was adopted for importance ranking of the uncertain input parameters of the given model. However, such flow models could involve one or several spatial inputs, for instance, fault dip, distance between fault and the injection well, friction angle of fault, permeability of fault, Young's Modulus of fault, injecting pore pressure and the stress field. Studying the sensitivity to each of these spatial inputs motivated the present work. The results led to the following conclusions: fault depth and fault dip significantly affect the behavior of the fault and the fault slip becomes violent with the fault depth increasing and fault dip decreasing. Furthermore, the results indicate that slip time increases with the fault dip decreasing and decreases with permeability of fault increasing. In addition, the calculation of seismic moment and moment magnitude of an earthquake demonstrates that it rises significantly with the decrease of fault dip and the increase of fault depth, and it decreases with the rising stress field. The results show that variations of the only controllable parameter injection pressure do not show great influence to the fault behavior compared with other geological factors, which imply site selection is extremely important for the CCS projects.

Jan 1, 2015

By J. Janeson

Wall control at the Pipe Open Pit is of primary importance in ensuring the long-term stability of the operation, while keeping costs to a minimum. Blasting techniques have been adapted to the variations in competence and structure of the wall rocks. A portion of the perimeter wall is being developed in incompetent peridotite . A recent change in pit slope design provides a wide safety berm on alternate benches. A support program which consists of pinning the crests of wide berms with vertical reinforced concrete dowels and horizontal bolting of walls shows evidence of increasing the stability of the pit walls. This paper describes the blasting and support techniques which are contributing to successful wall control in the Pipe operation.

Jan 1, 1979

By Olivia Gamache

When working in remote and extreme environments, projects are faced with new challenges for engineering and project execution. This is heightened when also working in countries with a developing environmental regulatory framework, small skilled workforce available for recruitment, and minimal infrastructure such as power, roads, and water. There is an increasing realization that social and environmental aspects need to be built into project execution. Giving proper attention to these issues during project development and execution, and maximizing opportunities is an ongoing challenge.

May 1, 2013

By M. K. Walter

"The underground operations of Kidd Creek Mines uses an average of 450 U.S. gpm water during regular operations, and discharges an average of 800 U.S. gpm through consecutive staged pumping lifts of 1200f t.Water is used as a flushing medium for the drilling operations and as a dust suppressant for drawpoint mucking. The water retains an average of 5% suspended solids by weight which is removed underground before being pumped to the surface. This paper outlines the treatment of the mine water for the removal of suspended solids which are chemically treated to settle out as a sludge product of 60% solids by weight. This process reduces the sludge handling operation by 50%. The sludge is systematically disposed into the ore passes.IntroductionThe Kidd Creek minesite, located 27 km north of Timmins, Ontario, produces 4.5 million tonne s of copper, lead, zinc and silver ores annually from its No. I and No.2 underground mining operations. Both mines use a sublevel blasthole stoping method of extraction.Water from the underground operation passes through a series of surface settling ponds, where it is treated to remove heavy metal ions from solution. A blend of the pond effluent with fresh water from Kidd Creek, supply the underground with water at an average rate of 450 U.S. gpm. Water flows from the production zones through coarse sumps and into a main pumping station. There are five main pumping stations underground, three in No. I Mine and two in the No.2 Mine.The No. 2 Mine pumping stations are located on the 4800 level and the 3600 level. All water below the 3600 level to the shaft bottom is controlled from the 4800 pumping station. The water from the 4800 pumping section is combined with water from the remaining levels of the No.2 Mine at the 3600 pumping station. Water from the 3600 pumping station is pumped to the 2400 pumping station in No. I Mine.The No. I Mine pumping stations are located on 2800, 2400, and 1200 levels. All water below the 2400 level to the shaft bottom is controlled through the 2800 pumping station. This water is pumped to the 2400 pumping station. The 2400 pumping station also controls the water below 1600level to 2400 level."

Jan 1, 1988

By R. Saulters, M. Garshasb

The Transportable Moisture Limit (TML) is the copper concentrate moisture content beyond which liquefaction may occur during shipping. This study indicates that TML is a function of mineralogical characteristics of concentrate, which in turn may directly affect moisture retention properties. A comprehensive mineralogical and chemical analysis was conducted to determine the impact of composition and mineral content on concentrate’s TML. The analysis indicates that the high TML value is associated with particular minerals such as gypsum, swelling clay, muscovite and pyrite. Since higher TML values allow higher moisture contents for shipping, this property is desirable for concentrate inventory management and shipping flexibility. Scarcity of minerals that may increase TML contributes to limitations of shippable inventory. INTRODUCTION TML is the maximum moisture content of copper concentrate beyond which liquefaction may occur. Moisture content above the TML is considered a shipping hazard as it may result in loss of lives and cargo. The details of TML testing are given in ISO 12742:2007 (ISO 12742). In principle, TML is 90% of the Flow Moisture Point. The method of testing for Flow Moisture Point and TML is based on procedures that provide pulsations that simulate the cyclic force of ocean waves to determine moisture levels at which the onset of concentrate flow may occur. International Maritime Organization (IMO) provides guidelines for developing and approving TML testing and moisture determination in the context of its Moisture Management Plan (MMP) for shipment of copper concentrate cargoes (IMO 2013). The IMO regulations are specifically provided in MSC.1/Circ. 1454 “Guidelines for developing and approving procedures for sampling, testing and controlling the moisture content for solid bulk cargoes which may liquefy”. Since each port has its own operational characteristics, resource availability, peculiarities of governmental structure, and desired methods of interaction with the authorities, it is necessary to adopt the IMO guidelines to the local requirements. In order to establish a TML and MMP measurement system, it is required to implement and follow proper guidelines for the relevant procedures. For example, sampling procedures are developed in accordance of ISO 12743, “Copper, lead, zinc, and nickel concentrates – Sampling procedures for determination of metal and moisture content”. Moisture content of copper concentrate samples are determined in accordance with ISO 10251, “Copper, lead, zinc, and nickel concentrates – Determination of mass loss of bulk material on drying”. To assure strict adherence to the MMP procedures, the overall system needs to be integrated into the site QA/QC system, which would make them auditable and certified in accordance with standards such as ISO 9001, ISO 17025, and ISO 17020.

Jan 1, 2019

By T. Negeri, M. Boisclair

"A hybrid process consisting of flotation and magnetic separation has been developed to concentrate multi-phase rare earth minerals associated with a carbonatite ore that contains a significant amount of niobium. Fine grinding to a d80 of <65 microns was required to obtain acceptable separation of 92% of the contained total rare earth oxide (TREO) and niobium in half the feed mass. Whereas it was possible to obtain 85% of TREO in 28% of the feed mass through staged cleaning, it was demonstrated that at least 87% and 85% recoveries of TREO and Nb respectively could be achieved in 16% of the feed if the rougher-scavenger concentrates were calcined, quenched, reground to <25 µm and then magnetically upgraded. The paper discusses the overall concept of the flowsheet and the experimental strategies that led to this progress. INTRODUCTIONOut of the approximately 250 minerals known to contain rare earth elements (REEs), only about 60 of them contain REEs in significant amounts. Over 95% of the world’s rare earth oxides (REOs) are believed to occur in the form of three minerals (Pradip & Fuerstenau, 1991) namely bastnaesite (Ce,La,Y)CO3F, monazite (Ce,La,Nd,Th)PO4 and xenotime Y(PO)4. An estimated 51.4% of global REO resources are hosted by carbonatite deposits with the same three minerals as major constituents (Weng et. al., 2015). Any one of the REEs or commonly all of them can be found in these minerals (Ravnaas, 2010). As the demand for critical REEs increases due to the ever increasing applications in advanced technologies, many deposits containing other forms of REE minerals will have to be developed. REE minerals are extensively dispersed and intergrown with several oxides, silicates, carbonates, and phosphate minerals. Consequently it is possible to liberate them only at fine grinding and is thus difficult to separate and produce high grade rare earth mineral concentrates. Most of these minerals contain other important elements such as tantalum (Ta), niobium (Nb), uranium (U), and thorium (Th) in varied quantities. REE minerals in the same ore may exist as carbonates, fluorocarbonates, niobates, silicates, phosphates etc. in association with gangue minerals belonging to different mineralogical groups."

Jan 1, 2016

By L. A. Melis, K. S. Fraser

"This paper describes the development of a milling circuit for the complex Midwest orebody, containing a high-arsenic uranium ore typical of that found in northern Saskatchewan. The results of preliminary bench-scale test work are summarized. Data from a pilot-plant program carried out at the Ontario Research Foundation are provided for the selected mill flowsheet. Also described are waste circuits which have been established to produce effluents of acceptable quality. Pilot-plant testing of sub-aerial tailings deposition is also described. The applicability of manufacturers&apos; equipment for the various circuits in the flowsheet is discussed.IntroductionThe Midwest uranium deposit is in northern Saskatchewan, 700 km north of Saskatoon, near the eastern edge of the Athabasca BasinDevelopment work on the project is directed by Canada Wide Mines Ltd., a subsidiary of Esso Resources Canada Limited. Participants in the project are Esso Resources Canada Limited, Numac Oil and Gas Ltd., Bow Valley Industries Ltd ., Mink Mining Corporation and Midwest Mining Corporation.The deposit consists of a series of flat lenses of massive ore overlain by a halo of lower-grade sandstone ore. The massive ore is formed of pitchblende and nickel arsenides, along with clay, and averages about 10% U and 9% Ni, The principal minerals are pitchblende (UO2-UO3), coffinite (U(SiO4)1-x(OH)4x), gersdorffite (NiAsS), niccolite (NiAs) and rammelsbergite (NiAs2). The sandstone ore, a friable clay-rich sandstone with sooty pitchblende, averages about 0.4% U and 0.6% Ni. Typical expected mill feed analyses are given in Table I.A bench-scale development program ore was carried out during the period from August 1978 to May 1981 in the laboratories of Lakefield Research of Canada Ltd. (Lakefield), (Lakefield, Ontario), the Colorado School of Mines Research Institute (CSMRI), (Golden, Colorado) and, to a lesser extent, the Ontario Research Foundation (ORF), (Mississauga, Ontario) and the Saskatchewan Research Council (SRC), (Saskatoon, Saskatchewan). Direction of the development studies was shared by Canada Wide Mines Ltd. and its metallurgical consultants, A.H. Ross and Associates. Input was received from Envirotech, Enviroclear, Interox America, and Knight and Piesold Ltd."

Jan 1, 1983

By J. C. Mitcheson

Mr. President, Mr. Mayor, Ladies & Gentlemen: IT GIVES ME great pleasure to have the opportunity, today, to speak on behalf of all the constituent. bodies of the Common-wealth Council of Mining and Metallurgical Institutions. For the past month we delegates have been right royally entertained across the length and breadth of Canada by Provincial Governments, City Councils, and other equally generous public organizations and private corporations. On this occasion, however, the President of The Canadian Institute of Mining and Metallurgy, our good friend Dr. H. J. Fraser, has been our host at the enjoyable reception preceding this Institute Luncheon, which luncheon was sponsored by our official host, The Canadian Institute of Mining and Metallurgy, one of our .constituent bodies.

Jan 1, 1957

By Piotr Malkowski

Studies on the properties of rocks heated to high temperatures are rather rare. Such research is occasionally conducted for example; in areas around nuclear power plants. The national Polish coal gasification (underground coal gasification, or UCG) project has, however, forced the analysis of the geomechanical properties of heated rocks in the vicinity of a designed geo-reactor. Ukrainian experience with UCG show that rocks up to 2 m from the burned coal seam be at a temperature > 600ºC. Such a high temperature will undoubtedly influence their physical properties. This paper presents studies on the strength and deformation properties of carboniferous rocks in the Upper Silesian region, where the UCG process is planned. Three types of rocks were tested: claystones, mudstones and sandstones. Laboratory tests of these rocks evaluated compressive strength, elastic modulus and weight loss. An evaluation of the results of the tests comparing the thermal conductivity of rocks and their specific thermal capacity was then carried out. All of the rocks studied were heated to 300, 600 and 1000ºC, and also evaluated at room temperature. This procedure shed new light upon the behavior of heated rocks in relation to their distance from the designed geo-reactor. The test results presented were developed within Research Task No. 3 ?Developing a technology of coal gasification for efficient production of fuels and electric power?, financed by The National Centre for Research and Development under strategic research and development programme ?Advanced Technologies for Energy Generation.?

Aug 1, 2013

By M. Mbonimpa

Field experimental cells were constructed in 2007 to assess the performance of different cover scenarios for the reclamation of the Parc 1 tailings disposal facility at the Westwood-Doyon Mine site (Abitibi, Quebec). Three configurations of cover with capillary barrier effects (CCBEs) with different thicknesses and material types for the moisture retention layer (MRL) were studied. MRL with 80 cm till, 40 cm till, and 40 cm clayey silt were used for cell nos. 2, 3, and 5, respectively. The capillary barrier layer (CBL) and drainage and protection layer (DPL) of the CCBE consisted of 30 cm gravel. A reference cell without cover was also constructed to compare the geochemical performance of the CCBEs. Due to an unexpected flooding in the leachate exit area of the cells in spring 2008, the cell instrumentation for hydrogeotechnical monitoring was postponed to spring 2009. Changes with time in volumetric water content, suction, soil oxygen concentration, and temperature were measured at different depths. This paper presents and discusses preliminary results obtained from spring 2009 to autumn 2010. In all cases, the degree of saturation Sr is lower in the CBL than in the MRL, indicating the presence of capillary barrier effects at the interface of these layers. Cell nos. 2 and 5 showed hydrogeotechnical behavior typical of an effective CCBE, with Sr maintained above 85% in the MRL and lower than 30?50% in the DPL and CBL. Based on the obtained results, and as expected, MRL thickness and the type of construction material used appear to affect the hydrogeotechnical behavior of the CCBE. Oxygen concentration profiles through the CCBEs were used to estimate the oxygen flux, and results indicate that cell nos. 2 and 3 performed better than cell no. 3. CCBE performance is currently being investigated using the geochemical monitoring data.

Aug 1, 2013

By Georgy A. Cherkashov, Andrey V. Efimov, Yury S. Borodaev, Nadezhda N. Mozgova, Sergey G. Krasnov, Tamara V. Stepanova, Alexander M. Ashadze

"Abstract - A horizontal mineralogical-geochemical ore zonation with a southeast to northwest trending succession of Cu and Fe (Zn) main zones has been discovered in the Logatchev hydrothermal field (14°45??N Mid-Atlantic Ridge). The major minerals are pyrite, chalcopyrite, bornite, isocubanite, digenite and chalcocite. Zn-sulfide, marcasite and covellite are less abundant. Rare minerals are native copper, zincian copper and cobalt pentlandite (first found in oceanic massive sulfides), Cu and Cu-Co-bearing Fe-disulfides. Two groups of the main sulfide assemblages with different copper contents are recognized: Group I comprises assemblages with primary sulfides (isocubanite, chalcopyrite, pyrite and Zn-sulfide; Cu up to 35 wt% in Cu-bearing minerals); Group II contains assemblages with secondary Cu-rich sulfides (bornite, digenite, chalcocite; Cu ~60 wt%) as well as rare minerals (cobalt pentlandite, native copper and zincian copper). The assemblages of Group I formed at a temperature of about 300°C; the sulfur fugacity (log fs2 atm) at 300°C is probably 9.9. Relations between minerals of this group are contradictory, attributed to non-equilibrium environments, and no unified sequence of crystallization of minerals has been determined. Minerals of Group II replace, rim or cross the assemblages of Group I. Group II minerals crystallized in a distinct sequence (cobalt pentlandite-bornite-digenite- chalcocite-native copper), with increasing copper content from the start to the end of the depositional sequence. This may correspond to pH from 7 to 8 near Eh = -0.2 at 250°C. Minerals of this group were generally formed under hypergene alteration processes. Compositions of ore minerals were studied by means of electron microprobe analysis (EMPA) (150 analyses). Narrow composition fields were revealed in all main sulfides, which comprised known experimental data. ZnS contains 6.0 to 28.0 mol.% FeS, which is close to data known for other hydrothermal massive sulfides from the Mid-Atlantic Ridge (MAR). A common admixture in ZnS is Cu (0.16 to 1.32 wt%). Rare grains of unusual anisotropic Fe-disulfides, (Fe0.95Cu0.05)S2 and Cu(Fe,Co)9S20, were found among the ore minerals."

Jan 1, 1999