Search Documents

By M. J. Sapko, R. W. Watson, E. S. Weiss

The relative incerdivity of several blasting agents was evaluated in the Bureau's Bruceton Experimental Mine (BEM) . The minimum charge weights resulting in the ignition of predispersed oil shale dust clouds were measured for each of the explosives. A 400 g unstennned charge of ANFO (ammonium nitrate-fuel oil) was sufficient to initiate an oil shale dust explosion, whereas a 1000 g unstenuned charge of an emulsion blend did not ignite the dust even with the addition of 4% methane gas. Several stenuning materials were evaluated in the BEM for their effectiveness in preventing the ignition of near stoichiometric methane-air mixtures. Water stenuning was superior to all other inhibitors tested against methane. Explosibility testing of fine sulfide ore dust in a 20 L chamber and in the BEM show that the dust is capable of propagating an explosion given nominal concentrations of 700 to 800 g/m3. Results are encouraging and irrlicate that there is merit in pursuing explosive composition as a means of reducing ignition probability of oil shale and sulfide dust clouds generated during nonnal blasting operations. The proper selection of explosives and stenuning materials should significantly reduce the probability of secondacy dust explosions in oil shale and sulfide ore mining.

May 11, 1988

By J. Zou

Open-cut method is most widely used for shallow utility lines installation. In urban areas, unexpected utility lines buried underground potentially turn open-cut construction into a highly risky operation, increasing the construction cost while presenting additional safety hazards. Examples include: breaking existing water main leads to flooding the downtown area; hitting an unexpected gas line causes an explosion. To prevent those accidents, the current practice is to stake out the underground utility lines before the open-cut construction based on the as-built information collected from various utility companies and government agencies. However, the as-built information is not always complete and accurate. To verify the locations of some important utility lines and protect them against damages caused by open-cut construction, new techniques and technologies are used but have their limitations in revealing underground utility lines, such as hydro vacuum method and ground penetration radars (GPR). The emerging technology of ultra-wide band (UWB) radar holds the potential to provide a cost-effective, non-destructive detection method. In this paper, a critical review of current practices and established methodologies is given. The functionality and working mechanism of UWB radar technologies are described. Application potential in open-cut construction is demonstrated by conducting lab experiments. Testing set-ups for detecting unexpected utility lines in soil along with preliminary results are presented. The effects of soil moisture content on the detection range are discussed. Research findings are summarized and constraints are discussed in conclusions.

Aug 1, 2013

By G. R. Baiden

"An Automatic Haulage Truck (AHT) has been developed for manless tramming of run-of-mine material in an operating mine. The AHT has a 70-ton capacity and uses an electric trolley system in combination with a computer control system to operate the vehicle. The purpose of the AHT was to provide a high capacity, high productivity material transfer system where conveyor belt applications are not immediately practical.The AHT project was started in 1983 at Inco Limited, Ontario Division as a result of the need for rapid material transport to match increased extraction rates resulting from bulk mining methods. The original concept was to use a continuous loader with the truck. However, in order to minimize development problems the truck project was considered a stand-alone project.The AHT project consisted of concept development, preliminaryand detailed design, manufacture, surf ace testing and mine implementation.The AHT was manufactured and ready for testing in 1988. At this point the truck was first moved onto the test track for debugging. This proved successful and in 1989the decision was made to install the AHT at Little Stobie mine on 2000 level. Commissioning of the system was started in 1990and at present a fully functional automated haulage system is in place at Little Stobie mine producing 3000 tons/day.This paper describes the project presenting results achieved to date."

Jan 1, 1992

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998

By Robert B. Parsons

"Starting January 1, 1987 employers, employees, and other taxpayers are confronted with a new set of rules dealing with the taxation of travel and housing benefits relating to isolated posts in Canada, and tax deductions relating thereto. The new rules may not be the simplest in the world, but they are reasonably fair and at least offer a hitherto unknown degree of certainty as to how such allowances are to be treated. IntroductionThe first shoe fell on February 26, 1986 when Finance Minister Michael Wilson' s first budget presented the framework for the future tax treatment of travel and housing benefits (so-called ""northern allowances"") provided to residents in remote regions of Canada. The second shoe fell some ten months later on December 22, 1986 when the Minister of Finance filled in the earlier announced framework with detailed rules. We now have a complete picture of the tax treatment of northern allowances. Here is what the picture looks like with effect from January 1, 1987.According to Revenue Canada, the net housing benefit to employees will be equal to the value of the accommodation provided, less any rent they have paid. In major centres such as Yellowknife and Whitehorse, having a developed rental housing market, the benefit amount will be based on the fair market value of the rental accommodation in that location. In other areas, employers will be required to value the housing benefits and, to assist employers, Revenue Canada has provided the following guidelines: Common shelter- $100 per month including the value of subsidized utilities Apartment! duplex-$270 per month excluding the value of subsidized utilities, or $400 per month including the value of subsidized utilities House-$450 per month excluding the value of subsidized utilities, or $650 per month in- c1uding the value of subsidized utilities.The amounts established as the values of accommodation will be adjusted annually after 1987 based on the housing component of the Consumer Price Index."

Jan 1, 1987

By M. Savella

The Runruno Gold Project is located on the island of Luzon, approximately 200 km north of Manilla in the Philippines. The mine is a surface mine operation and use the proven BIOX® and carbon in leach processes to recover gold, and the ASTER™ process for detoxification of the CIL residue prior to discharge to the Residue Storage Impoundment (RSI). Work to date has defined a mineral resource of 1.39 million ounces of gold, and the operation will produce 96,700 ounces of gold per annum over a mine life of 10.4 years. The BIOX® circuit is designed to treat 140,000 tpa of concentrate with a design capacity of 404 tpd of concentrate at a design sulphide sulphur grade of 17% S2-. The Runruno project is the first BIOX® plant to implement the Generation III BIOX® design principles. As part of the Generation III BIOX® program Outotec supplied a turnkey, containerised metallurgical laboratory to facilitate the first four stages of the BIOX® and ASTER™ inoculum build up requirements. BIOX® inoculum build-up was started during early January 2015 with 5 litres of stock cultures shipped from South Africa. The BIOX® culture was successfully adapted to concentrate produced from the mini plant during March 2015. The ASTER™ inoculum build-up commenced during early August 2015 utilising 27 litres of ASTER™ bacterial inoculum already adapted to similar process conditions expected during commercial operation. This paper will detail the various stages of inoculum build-up through to commissioning and ramp-up of the BIOX® and ASTER™ Processes at the Runruno Gold Project. The paper will highlight some of the factors affecting the commissioning process as well as the improvements seen through the introduction of the Generation III BIOX® design principles.

Jan 1, 2017

By A. Montera, M. Loken

"The process of blending consistent and predictable feed for the roasters is critical for optimizing product quality and controlling production costs. To assist in this process, online PGNAA slurry analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100 % of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their full stream, elemental slurry analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company, consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced.The Strathcona Mill receives ore from Nickel Rim South, Fraser, and third-party miners to produce two concentrate streams. One is a nickel-copper concentrate for use by the Sudbury Smelter; the other is a copper concentrate which goes to other Glencore operations for smelting and refining. The Sudbury Smelter converts the mineral concentrate into a high grade matte containing nickel, copper, cobalt and platinum group metals. This matte product is shipped to Glencore's Nikkelverk refinery in Norway for further processing. In 2015, the Sudbury INO Smelter completed the first phase of the Process Gas Project (PGP); a series of process changes and capital investments designed to reduce sulphur dioxide (SO2) emissions in accordance with Ontario Regulation 194. A critical element of the planned emissions reduction was the elimination of a higher percentage of sulphur contained in input concentrate streams, which can then be captured and converted to sulphuric acid."

Jan 1, 2017

By J. Keith Haddock

"Introduction The Coal Valley Mine is operated by Luscar Stereo (1977) Ltd. with the Alberta Energy Company having a minority interest. The mine produces 2.0 million tonnes of bituminous thermal coal per year. Deliveries include 1.5 million tonnes to Ontario Hydro and 0.5 million tonnes to the export market via bulk handling facilities on the west coast near Vancouver, B.C. There are a number of mining methods utilized at the mine including open-pit by truck and shovel, strip mining with large draglines and stripping with scrapers. The mine is located 100 km south of Edson, Alberta. Geology The coal measures are concentrated within a 210-metre int~rval of the Paleocene section. The coal seams were originally named by the mining companies in the earliest days of development of the area and these names continue to be used today. Of the five main seams, only three are presently economic to mine based on quality, thickness and depth of cover. These are the Val d'Or, Upper Silkstone and Mynheer. The Coal Valley Mine is located in the structurally deformed foothills area of Alberta and the structure of each mining area is therefore very complex. The general bedding strike is 305 degrees azimuth but major thrust faulting and folding has extensively deformed the natural seams as a closer examination will show. The Mynheer Seam, located at the base of the coal measures, ranges in thickness from 5 m to 10 m and has numerous bentonite and shale partings. Because of inherent geological features, the Mynheer Seam has been subdivided into two zones, the Mynheer 'A' and the Mynheer 'B', and the mining of coal in these zones has necessitated the utilization of distinctly different mining methods. The structural regime of the Mynheer 'A' zone consists of an overturned asymmetrical anticline crest containing a steeply dipping major thrust fault which has raised the seam above the present topographic level. Further extensive shearing and rotation of the coal has resulted in the coal taking a 'pod' shape. The Mynheer 'B' Zone is a continuation to the southeast along strike from the Mynheer 'A' Zone. The bedding dips to the southwest at an average of 12 degrees and is interrupted at the south end by a transverse fault and to the north by its outcrop at the surface."

Jan 1, 1985

By F. P. Agterberg

"IntroductionTHE KNOWLEDGE about the mineral resources in a region ranges from relatively precise ore-reserve estimates for known deposits to probabilistic estimates concerning the speculative resources which may be discovered in future at greater depths and in the less-explored parts of the region. Previously developed probabilistic methods for regional resource evaluation (1) are based on the following two assumptions.(1) The probability that a specific block of rock, or part of a region close to the topographic surface, contains undiscovered deposits can be estimate d by weighting selected geological, geophysical or geochemical parameters for that block. The weights are computed by considering similar environments which are known to contain deposits.(2) Some of the characteristics of the undiscovered deposits, such as ore tonnages and average grades of metals contained in the ore, can be evaluated by considering probability distributions f or known deposit data. These methods were initially applied to Precambrian deposits in the Abitibi Volcanic Belt of the Canadian Shield (1).Since 1972, statistical methods for quantitative resource evaluation have been applied to the occurrences of the mainly Paleozoic base metal deposits in t he Canadian Appalachian Region. The objectives of this project (Project Appalachia) have been discussed by Leech (2) in a paper that introduces 8 papers with results of the exploratory data analysis. Project Appalachia represents an effort to develop and apply methods of combining information and concepts from regional geology, metallogeny and geomathematics for computer- aided regional mineral resource evaluation."

Jan 1, 1977

By W. J. Kuit

Since closure in 1968, the Wedge Mine, situated adjacent to the Nepisiguit River in New Brunswick, has been flooding with acidic water containing toxic levels of heavy metals. Cominco Ltd. has undertaken a series of pollution control measures to mitigate the threat posed to the river quality. Included has been a successful treatment campaign in 1976 which discharged in excess of 30 million gallons of high-quality effluent from the accumulated volume of mine water. The sources of contamination have been identified as actively leaching waste dumps. A comprehensive program of permanent corrective measures has been prepared which will culminate in mine backfilling. Once completed, the unacceptable burden of water treatment in perpetuity at a non-producing property will be removed.

Jan 1, 1977

By Chuan-Jian Zhong

Gold-based nanoparticles in the size range of a few nm have attracted increasing interests in catalysis, sensors and biomedical applications. The study of the unique catalytic properties of nanosized gold was inspired by the pioneering work of Haruta on the nanogold-catalyzed CO oxidation (1-4). There have been a number of excellent reports discussing both fundamental and application aspects of gold nanoparticles in catalysis (3-8). Our work reported herein is aimed at investigating the preparation and application of gold and its alloy nanoparticles for potential applications in fuel cell catalysis. Fuel cells operating by electrochemical oxidation of hydrogen or methanol fuels at the anode and reduction of oxygen at the cathode are attractive power sources due to their high conversion efficiencies, low pollution, lightweight and high power density. While methanol offers the advantage of easy storage and transportation in comparison with hydrogen fuel cell, its energy density (~2000 Wh/kg) and operating cell voltage (0.4 V) are much lower than the theoretical energy density (~6000 Wh/kg) and the thermodynamic potential (~1.2 V). The poor activity of the anode catalysts and inefficient activity or issue related to "methanol cross-over" at the cathode electrode are associated with the loss of about one-third of the available energy at the cathode and the other one-third at the anode. Extensive studies have been focused on Pt-group metals (Pt+Pd+Rh+Ru+Ir (PGM)) for both anode and cathode catalysts. A major problem is the poisoning of Pt by COlike intermediate species (9,10). Recently, oxide-supported gold nanoparticles in the <10 nm size range have emerged as one of the best catalysts for CO oxidation (1-3,11), and for water gas shift reaction in reforming stage using 5 nm Au on Fe2O3 (6). Gold and its alloy with other metals in the nanosize range present new alternatives (2,12). Whether the unique properties of gold nanoparticles can be exploited for addressing these problems is a focus area of our work. The ability to harness the large surface area-to-volume ratios and the unique surface sites of nanoparticles in <10 nm size range, especially in heterogeneous catalysis, constitutes a major driving force in fundamental research and practical applications of nanoparticle catalysts. It is this size range over which the metal particles undergo a transition from atomic to metallic properties. The understanding of factors controlling the morphological and surface reconstitution associated with such a size range is of fundamental importance to the ultimate exploration of nanostructured catalysts. We have been investigating the interfacial structures and properties of core-shell types of nanoparticles consisting of gold or alloy nanocrystal cores and organic monolayer shells that were prepared by twophase synthesis (13) and processing (14) protocols. Important attributes of such nanoparticles include controllable size monodispersity, processibility, and stability towards size- and composition-tunable catalysis (15-21). Some of these attributes were studied for understanding their electrocatalytic properties in the oxidation of methanol and reduction of oxygen, which are of fundamental interest to fuel cell technology.

Oct 1, 2003

By Michael R. McPhie

Topics of Discussion 1. The Global Mining Initiative (GMI) and MMSD North America (Brief) 2. Task 2 of MMSD North America ? A Test for Sustainability 3. The Seven Questions and their Application 4. Key Recommendations and Next Steps GMI = Global Mining Initiative Significant international collaborative effort supported by more than 30 of the world?s largest mining/minerals firms which sought to involve all communities of interest. Three major streams of activities: 1. Mining, Minerals and Sustainable Development Project (MMSD) ? 4 regional Process (North America, Southern Africa, South America, Australia) 2. Creation of ICMM (formerly ICME) 3. Major conference in Toronto in May, 2002

May 1, 2002

By M. R. Swaan, G. J. Stewart

"ABSTRACTThe application of failsafe techniques to ask the ""What if"" questions about any process has been well established in the chemical industry for many years. The unusual number of fatalities that occurred in Ontario during 1986-87, prompted Inco management to look at the Fail Safe techniques as a method of improving safety performance.INTRODUCTIONOne of the major areas at any time for potentially disastrous accidents is the shaft, where all men and materials must travel. In April 1987, Inco&apos;s Thompson Mine&apos;s first Fail Safe Team was established to look at its shaft operations. The initial group of eight people was made up of hourly equipment operators, mine foremen, engineering, maintenance and the superintendent. This group took the name of Shaft Risk Analysis Team or SRAT.The many tasks or jobs that are performed in a shaft prompted the team to divide the work under six major headings; slinging, moving men, skipping, dewatering, shaft inspections and moving materials. Each of these areas contained many different tasks which are interrelated. The only way to understand this interrelationship was to flow chart the steps that actually occur in getting any job done.The flow charting is done by the foreman and operators using existing standard manuals and their experience of what actually takes place. In many cases, it soon became apparent that they had been ""working around"" many problems created by their standards. Fine tuning of these flow charts takes place at the weekly meetings, where input from all involved leads to a better understanding of the actual job being analyzed and its potential hazards. Two major points need to be emphasized in getting good flow charting at a mine:I. It must never be blame oriented or you will never discover how the jobs are actually done and hence you won&apos;t know what to improve.2 . All team members must have equal voting rights in deciding how to put the charts together so that they have ownership of the finished product. It is far too easy to end up with amanagement view of the way it should be. Many different techniques or methods are being employed to improve the tasks and reduce the risks associated with any job once the basic flow chart is established. The ones found to be the most useful are highlighted."

Jan 1, 1989

By T. G. Carter

"Damaging seismicity associated with deep faulting in both mining and civil excavations not infrequently occurs without warning, and often before proper mitigation measures have been put into place. Severe squeezing is also a common problem for excavating through deep major faults. While both problematic conditions are difficult to predict and characterize, there is often a need at pre-feasibility and feasibility level to more reliably estimate the possible level of risk posed by such geologic structures. This paper introduces some structural geologic techniques that have potential application for both mining and civil applications for aiding forewarning of the extent of these types of problem.INTRODUCTIONEncountering adverse faulting at depth in deep excavations, whether for mining or civil purposes can create serious economic and safety impacts. For deep mines or for deep tunnel projects, measures are available for aiding prediction of the extent of possible influence that large scale faults could create, but these techniques are rarely if ever applied as part of routine site investigation programs, or even as part of risk assessment evaluations. Several well established structural geologic methods of palao-history reconstruction have potential application for aiding forewarning of the extent of these types of potential problem by allowing estimates to be made of:• controlling stress orientations that might engender reactivation movement;• principal stress magnitudes that could lead to failure initiation, and• probable mechanisms of fault deformation - brittle (bursting) or plastic (squeezing).This paper explores several structural geological and rockmass characterization techniques that have application for unravelling fault structure of importance to deep engineering projects. Their application for mining or tunnelling purposes is advocated in conjunction with conventional rockmass characterization assessment approaches using GSI, RMR and/or Q to aid early recognition and definition of potential adverse ground condition behaviour associated with intersection of significant faulting at depth."

Jan 1, 2015

By K. Adham, T. Buchholz

"Significant capacity increases to meet new production demands can often be fulfilled through debottlenecking of an existing production facility, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. To achieve that goal, it is important to model and calculate the existing ultimate capacity of each processing plant area, and that of each key equipment sector within the plant areas. This paper describes a methodology of how process modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the sweet-spots (minimum cost points) for a plant expansion – leading to a road map of the subsequent debottlenecking project implementation.The debottlenecking technique is presented through a generic work-flow narrative which can be applied to different mineral processing studies, starting with establishment of heat-and-mass balances, drawing a bottleneck diagram, brainstorming capacity increase options, and preparing a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients.INTRODUCTIONWith the softening of the metals and minerals prices, and the escalated costs of building new processing plants, it is now economically more viable to improve and debottleneck the existing facilities, rather than build new ones. However, spending new money on old plants requires careful considerations, in order to identify the most economically advantageous incremental steps of improvement and the best potential returns on investment. Process modeling, hand in hand with plant measurements, can identify the best scenarios to balance the three aspects of plant capacity (nameplate, utilization and yield), both at the global and the individual system and subsystem levels."

Jan 1, 2016

By E. Onal, C. Craddock, A. Chapman, M. R. Endsley

ABSTRACT Mining equipment operators must interpret and respond to complex information delivered by technology-centric rather than user-centric systems. The ability to achieve high situation awareness (SA) in the face of this data overload is a key challenge to effective decision-making and information exploitation. Incidents attributed to human error that compromise safety and result in loss of revenue, or even life, are often the result of system designs that overload human cognitive capabilities. This paper defines SA as it relates to the operation of mining equipment and describes the design and preliminary evaluation of a new electric shovel operator user interfa

Jan 1, 2013

By Jack Parker

"The original design of mine openings and pillars at White Pine was based upon traditional assumptions; i.e., that the principal load is due to the weight of overburden, and that horizontal stresses are equal to one-. third of the vertical.Beginning January, 1964, borehole deformation measurements confirmed suspicions that the principal stress is horizontal and several times greater than the vertical.Vertical stress appears to be directly related to depth, but lateral stresses vary considerably in direction and magnitude. The direction of major principal stress lies parallel to the bedding and is apparently parallel to tension joints. Lateral stresses appear to originate from an igneous intrusive.Mining induces stresses which add to the primitive stresses, in some areas precipitating failure. In this paper, rock failures are illustrated, methods of measurement and typical results are given, and measures to counter or utilize the lateral stresses are described."

Jan 1, 1966

By D. Tao

The adverse effects of clay particles on coal and mineral processing processes such as gravity separation, flotation, filtration, and thickening are well known in the mining industry. In particular, the presence of ultra-fine clay particles deteriorates froth flotation performance, which has been attributed largely to slime coatings that inhibit bubble attachment and to adsorption of the frother and/or collector by the clay particles. The present study was conducted to evaluate the performance of clay binding agents developed by Georgia-Pacific Resins, Inc. in enhancing coal and mineral flotation performance. Mechanical and column flotation tests were carried out using coal and potash samples. Process parameters investigated include slurry solids percentage, impeller rotation speed, binder dosage, collector dosage, etc. Flotation results show that use of GP reagents significantly enhanced flotation efficiency under different conditions. The required binder dosage and conditioning time was about 1 lb/t and 0.5-1 min, respectively. More significant improvements in process performance were observed at higher solids percentage and higher impeller rotation speed.

Jan 1, 2006

By P. W. A Severin

"The Sturgeon Lake deposit, a partly eroded lens of massive sulphides with an underlying sulphide stringer zone, is one of five orebodies that occur in the Sturgeon Lake area of northwestern Ontario within volcaniclastic rocks of the Archean Wabigoon Subprovince in the Superior Province of the Canadian Shield.The Sturgeon Lake Cu-Zn-Pb-A g-Au deposit was discovered in October 1970 as a result of an I.P. survey. Production from this open-pit mine began in March 1974 and continued until the ore was exhausted in March 1980.The Sturgeon Lake property is underlain by basaltic volcanics, minor amounts of mafic lapilli tuff and rhyolite volcaniclastics. A quartz crystal-bearing rhyolite occurs at the top of the felsic volcaniclastics and is ""capped"" by the Sturgeon Lake massive sulphide deposit. The felsic volcanics have been intruded by a crudely layered sill-like, carbonatized mafic intrusion. Recent work suggests that the felsic rocks that underlie the Sturgeon Lake deposit are lateral equivalents of those in the vicinity of the Mattabi Mine and are not correlative with the dacitic volcaniclastics that underlie the Lyon Lake and Creek Zone deposits. Hydrothermal processes that resulted in the formation of the Sturgeon Lake orebody have resulted in a depletion of Na2O, CaO and FeO and an increase in MgO, K2O, copper and zinc. In the vicinity of the sulphide stringer zone, the rhyolites are ""bleached"" due to silicification and sericitization. The rocks lying immediately below the massive sulphides are locally strongly chloritic.The Sturgeon Lake deposit may have formed on a top ographic high which prevented mafic flows and dacitic volcaniclastics that underlie the Lyon Lake and Creek Zone deposits from inundating the Sturgeon Lake fumarolic vent from the west. Continued or resurgent activity from the Sturgeon Lake fumarole may have resulted in the formation of the Lyon Lake and Creek Zones as more ""distal "" deposits in topographic lows. The Sturgeon Lake, Lyon Lake and Creek Zone deposits were subsequently overlain by mafic tuffs and flows."

Jan 1, 1982

By D. R. E. Whitmore, J. M. Harrison

There are five logical stages in the search for orebodies in virgin territory, namely: (1) reconnaissance inventory of geology, and related investigations; (2) development of broad concepts as a basis for selecting regions of potential mineral deposits; (3) assessment of criteria leading to specific localities within these regions; (4) geo-physical and geochemical studies that will delineate small anomalous areas; and (5) stripping, drilling or other means of locating ore. In addition, the development of new means of extracting mineral resources and the finding of new uses play a vital role in our mineral industry. The continued growth of this industry will be largely governed by our ability to develop or to adapt new concepts and techniques, and to produce a greater number of scientists and engineers. It should always be remembered that more than one-third of Canada's exports are dependent upon our ability to find, develop and economic-ally exploit new orebodies.

Jan 1, 1967