Search Documents

By C S. Stevens

This paper describes the problems encountered and the steps taken to solve them in milling an ore containing relatively large amounts of pyrrhotite. A complex and greatly lengthened flotation circuit was required to recover the pyrrhotite. A very low pH had to be maintained in the cyanide circuit in order to get good recovery of the gold and maintain reasonable cyanide recovery. Introduction D ELNITE Mines Ltd., a gold mine situated about 5 miles by road south and east of the town of Timmins, Ontario, is serviced by two shafts. No. 2 shaft extends from surface to the 2875-ft. level, and No. 3 shaft, an internal winze, extends from the 2875-to the 5275-ft. level. No. 2 shaft was stopped at the 2875-ft. level because of a heavy band of chloritic schist which necessitated a drive to the north for 1000 feet, where No. 3 shaft was sunk. The latter bottomed in the schist at the 5275-ft. level. From the 2500 to the 2875-ft. level in No. 2 shaft, the ore was

Jan 1, 1965

By Arthur M. Whiteside

Discussion of the laws bearing upon the economics of mining in this province at once resolves itself under three headings: (a) The rights and obligations of holders of mineral bearing lands; (b) Taxation of mines; (c) Regulation of methods adopted in financing mining operations. Titles: The law relating to titles is contained in the Mineral Act, Placer Mining Act and Coal Mines Prospecting Act. Origin: Mining laws in force in this province and elsewhere on the continent had their origin in the rule-of-thumb regulations adopted by prospectors themselves, when, far from the centres of civilization and the seats of the courts of justice, they found it necessary, for mutual protection, to fix the conditions of possession by right of location, and to prescribe the duties to be performed in order to enable the individual to maintain his ground against all comers. These regulations have been codified and added to by legislatures, until we find adequate protection and safeguard to property in the laws of this province.

Jan 1, 1924

By Marcin Ziemski

This paper reports on an energy efficiency analysis completed as part of a research project looking at energy reduction opportunities in minerals processing operations. The plant discussed is a gold production facility owned by Newmont Gold in the Tanami region of central Australia. Due to its remote location, lack of nearby gas pipeline or power grid, the operation has been completely dependent on diesel fuel for its electricity generation and transport needs. The mine and processing plant use electrical power at a rate of 12MW to 18MW, resulting in a monthly electricity cost of over US$1.5M. The high cost of diesel combined with an impending power generation capacity shortage drove Newmont to undertake the energy efficiency study. An energy audit of the plant showed opportunities for significant energy savings through the strategic use of waste heat, fuel replacement alternatives and renewable energy sources.

May 1, 2007

By John C. Lyons

"The Wabana iron ore deposits occur as flat-dipping beds of oolitic hematite and chamosite, of Lower Ordovician age, which outcrop for 3 miles along the northwest coast of Bell Island, Conception Bay, Newfound-land, about 16 miles from St. John's.The deposits occur in three zones, Upper, Middle, and Lower beds, separated respectively by 30 feet and 215 feet of shale and sandstone. They are primary sediments laid down in a shallow tidal basin by the precipitating action of a marine environment on iron-rich fresh waters flowing into the basin.The ore-bearing zones, while of wide areal extent, are not uniform beds of hematite that can be mined wholesale. The action of waves and currents during sedimentation; the delta pattern, velocity, and transporting power of streams flowing into the basin; the contours and oscillations of the sea bottom on which the sediments were laid have all been fundamental in the emplacement of richer and thicker mineable sections, and of lean zones so intercalated with shale as to be unmineable.The preservation of the deposits is due to their location in the Conception Bay syncline and to a considerable upthrust of the country east of the bay in post-Ordovician time.The hematite deposits were first recognized as such in 1892, and soon after were acquired by the Nova Scotia Steel and Coal Co. They are now being mined by Dominion Wabana Iron Ore, Limfred, a wholly owned subsidiary of the Dominion Steel and Coal Corporation, Limited. Production started in 1895, and up to the end of 1955 totaled 58,588,516 long tons of hematite ore, having an average dry analysis of about 51 5 per cent iron, 11 8 per cent silica, 0·9 per cent phosphorus, and l ·5 per cent moisture. About 40 per cent of the total tonnage mined has come from surface stripping and on-shore mines. These areas have now been almost completely depleted, and operations are confined to submarine mines extending for two miles off shore under the waters of Conception Bay. Three sub-marine slopes are currently in operation, Nos. 3 and 4 working in the Lower Bed and No. 6 in the Middle Bed. A general picture of the workings is shown in isometric projection in Figure 1. Submarine mining has been entirely by the room-and-pillar method, with an extraction of 60 per cent. The deepest workings, at a vertical depth of 1,850 feet below sea-level, have a rock cover of about 1,500 feet. No mining is done in areas where the rock cover is less than 200 feet. To date mining has explored six square miles of a potential area that may exceed 50 square miles."

Jan 1, 1949

By A. M. Gaudin

Introduction The discovery of artificial radioactivity, that is, of radioactivity of acorns other than those which are naturally radioactive, has increased vastly the possibility of using radioactivity as an analytical cool. The incomparable value of radioactive atoms, which are commonly termed tracers, arises from the extreme sensitivity of this analytical method. To get an idea of this extreme sensitivity it may be useful co recall that gravimetric analytical methods will not permit the weighing of anything much lighter than one-hundredth of a milligram of material. Under the most favourable circumstances, this represents an uncertainty in the answer of 1016 acorns, or 10,000,000,000,000,000 acorns. Accurate spectrographic methods possibly have a sensitivity 10,000 times greater than this, but the uncertainty is still of the order of 1012 atoms. The tracer permits ascertainment of decay of a single atom so that its sensitivity, without half trying, can be several orders of magnitude greater than that of any other method available co chemists. In addition co the sensitivity of tracers to which reference has just been made, tracers have another property which makes them unique. A radioactive atom is almost exactly like the corresponding non-radioactive acorn m regard to its electronic structure, and therefore in regard to its chemical properties. The nucleus is different, but the nucleus does not participate in chemical reactions. Therefore, a tracer acorn behaves like an ordinary atom until such time as its nucleus undergoes a catastrophic decay. This unique property permits one to use tracer acorns as atomic spies and therefore to follow the behaviour of acorns of a certain kind among their own kind. In other words, the tracer method permits us to study and measure what we call self-diffusion. All of the uses of tracers that have been made depend on the two properties co which reference has been made.

Jan 1, 1949

By S. E. Jackson, L. J. Cabri

Quantitative determination of gold at sub-ppm concentrations in sulphide minerals is an important component of deportment studies for sulphide-gold deposits. Laser Ablation Inductively Coupled Mass Spectrometry (LA-ICP-MS) analysis is preferred for this application because it rapidly and cost-effectively provides spatially resolved (<20 pm), low ppb concentration data for gold and other elements in mineral grains. Recent advances in LA-ICP-MS analysis include the development and application of elemental mapping. Raw signals from multiple line scans or lines-of-spots are deconvoluted and calibrated to generate elemental maps which provide detailed information on spatial variations of gold and other elements within and between grains.

Jan 1, 2011

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By Z. Trojanová

Mg micropowders generated by gas atomisation of a magnesium melt with argon were mixed and ball milled with ceramic nanoparticles prepared by laser-induced gas phase reaction. The materials were then hot extruded. Specimens were deformed in tensile as well as compression tests at temperatures between 20 and 300 °C at a constant initial strain rate. The flow stress is significantly influenced by the test temperature. The yield stress decreases with temperature. This decrease and the flat character of the stressstrain curves at elevated temperatures indicate possible contributions of softening processes. The materials studied exhibit high-damping characteristics. The results are analysed and possible mechanisms are discussed.

Jan 1, 2006

By Jian-bin Xie, Lin-fang Shen, Zhi-liang Wang

"In order to research temperature field for construction of connecting passage in Metro using artificial freezing method, the finite difference software FLAC3D is employed to numerically simulate construction process of connecting passage. During construction, the overall distribution of temperature field around connecting passage, the relationship between soil temperature and freezing time, the distribution and variation for the thickness of freezing wall are studied from the perspective of numerical analysis. The results show as follows: after 55 days’ freezing, the soil temperature surrounding connecting passage is about -24 oC ~ -28 oC, and the minimum thickness of freezing wall is about 4.0m, which is larger than the design value 3.1m. So construction conditions have satisfied to the excavation of connecting passage and pumping station. During the excavation of connecting passage, soil temperature has almost no obvious change and the thickness of freezing wall remains constant mainly. After 45 days’ normal thawing, the temperature of freezing wall rises 12 oC approximately. And the soil temperature rises faster at the beginning of the normal thawing stage. In the whole process of construction, the frozen area is about 5m outside the edge of connecting passage, and the cooling area is about 10m outside the edge of connecting passage. INTRODUCTIONThe first recorded application of the artificial freezing method is on a mineshaft project in 1862, and it has been widely used in foundation pit engineering, subway tunnels, mine shaft engineering and so on (Wang Zhiliang, 2010; Zhang Juanxia, 2012; Qiu Fan, 2007; Zhou Xiaomin, 1999). This method has many advantages of enhancing soil strength; decreasing permeability and adopting various unstable soils (silt clay, sand, gravel, etc.). It has been applied successfully in metro engineering construction in Beijing, Shanghai and Nanjing. According to incomplete statistics, the construction of connecting passage using artificial freezing method accounted for 98% in Shanghai metro (Qiu Fan, 2007)."

Jan 1, 2015

By Washington Luiz Mafra

Every year the conventional direct reduction processes ? Midrex and HYL III ? increased their market share in the world steel production, even though they are only economically feasible in countries where natural gas is available at competitive prices. In this context, the new Midrex projects are based on large reactors (Megamod - 1.5 to 1.8 Mt/y of DRI), reduction temperatures of the metallic burden up to 850oC, with bustle gas temperatures between 960oC e 1050oC. Thus, the requirements of metallic burden performance, as well as the evaluating methods, usually based on ISO standards, need to be reviewed. It is well known that the standards usually applied to quality evaluation do not reflect the performance of metallic burden inside the reactors. This paper describes the different methods of evaluating the disintegration under reduction of DR pellets based on ISO 11257 standard. This is the most important method used by pellet producers and customers for evaluating DR feedstocks. The different methodologies tested to evaluate the disintegration under reduction had varying results, evidencing the relevance of the method and the quality of the pellet. Nevertheless, validating the method in an industrial reactor is still fundamental.

May 1, 2007

By W. D. Sinclair, R. J. Cathro, E. M. Jensen

"The Cash is one of the largest porphyry copper-molybdenum Deposits found in Yukon to date. It is 80 km northwest of Carmacks, within the unglaciated portion of the Dawson Range, and is associated with the Big Creek fault, an important tectonic feature. Part of the mineralized zone is blanketed by up to 70 m of alluvial drift . The remainder is covered by a relatively thin residual soil layer. The mineralized zone, however, was not detected by conventional stream-sediment sampling because pathfinder elements, such as Cu and Mo, have not been geochemically dispersed into the main drainage system. The deposit was discovered by a combination of soil analysis and inspection of rock fragments from small pits.Twenty widely spaced, shallow drill holes have outlined an areaover 2700 m long and 550 to over 1000m wide that grades more than 0.1% copper equivalent (% CuE = % Cu + (5 x % MoS2)). Two smaller zones grading over 0.4% copper equivalent occur within the larger area. The limits of the widest end of the deposit have not been delineated.The Cash deposit is fairly typical of high-level, calc-alkaline porphyry copper-molydenum occurrrences in the Canadian Cordillera {cf, CIM Special Volume 15) and is representative of most prospects in the Dawson Range. It is associated genetically with a subvolcanic complex of small, irregular stocks and dykes of feldspar porphyry and related breccias of Late Cretaceous age. Copper and molybdenum sulphides occur along fractures, in quartz veinlets and disseminated in feldspar porphyry and in older metasedimentary and intrusive rocks. Higher-grade zones of copper and molybdenum have associated potassic alteration. Phyllic alteration is, in part, superimposed on potassic alteration. Argillic alteration occurs locally.This paper describes the history of the discovery and the geochemical and geophysical characteristics, together .with the regional geology, and the nature and distribution of the host rocks, hypogene mineralization and hydrothermal alteration."

Jan 1, 1981

By S. Hopkins, R. Preston, S. Gillis

"This paper examines typical visual inspections of operational soft rock mine shafts and discusses some of the challenges involved, many of which are associated with inconsistent inspection practices. The paper presents the development of a more standardized approach to periodic shaft inspections that supplement the more frequent inspections performed by shaft crews at the mine. This approach helps to keep an accurate record of changing conditions, compare conditions between multiple mine sites, as well as prioritize and plan potential remedial work. INTRODUCTION Shaft inspections, whether they are performed daily or weekly by members of the shaft crew at the mine, or periodically by consultants, traditionally involve a visual inspection undertaken with personnel traveling on an inspection deck on the conveyance, taking notes and photos. Inspections are typically required by mining regulations and carried out to identify and address hazards before a safety incident occurs that could cause harm to people or damage to property, as well as to help plan required maintenance work. Depending on the site, there can be many challenges associated with inspections in the shaft, especially compared to a typical inspection at surface. Some of these challenges are associated with the shaft environment itself, while others are related to the subjectivity of inspections and a lack of standardization, particularly between multiple sites within the same operating company. Recognizing these challenges, a more consistent and repeatable approach to shaft inspections in soft rock mines is evolving. This approach involves reviewing available historical data, comparing sites with similar conditions, establishing survey control, documenting observations and measurements with locations, and updating as-built or condition drawings. Part of this standardized approach is the implementation of an innovative 360-degree camera with a high-power lighting system that can be used either remotely or alongside personnel completing a traditional visual inspection. The system uses six cameras to take photos at a rate of 15 frames per second, with the image data subsequently processed and stitched, then joined into a high-resolution video. This tool improves time-efficiency, objectivity, and repeatability of inspections."

Jan 1, 2019

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By William C. Martin

"Consolidated Sudbury Basin Mines Limited owns two mines, 4 miles apart, near the southwest end of Sudbury Basin. The Errington mine lies close to the north boundary of Creighton Township and about 18 miles by car from Sudbury. The Vermilion Lake mine is in Fairbank Township, on the south side of Vermilion Lake.The first discovery of base-metal mineralization within Sudbury basin was made by James Stobie in 1897 at Stobie Falls on the Vermilion River, half a mile west of the Errington mine. A few years later Alphonse Oilier made a discovery of massive pyrite with base-metal sulphides near the west end of the present Errington workings.No work of consequence was done on these discoveries until 1924, when Joseph Errington acquired options on a large acreage of ground which was later taken over by the Treadwell Yukon Company Limited. After considerable diamond drilling this company sank No. 1 shaft in 1926. In the next three years, a large amount of underground development was done, a pilot mill was constructed and operated for two years. All operations ceased in 1931 with the fall in metal prices. While in operation the pilot mill treated 186,172 tons of ore the average grade of which was 1·07 per cent copper; 1 10 per cent lead; 4·60 per cent zinc; 0·03 ounces gold; and 1 70 ounces silver.Up to the time of closing in 193 l there had been completed at the mine 26, 790 feet of lateral work and 75,500 feet of surface and underground diamond drilling. The company records, however, showed no figures on ore reserves, except broken ore in stopes amounting to about 60,000 tons. A study of the plans, prior to reopening the mine in 1952, showed 1,450 lineal feet of ore (at 1952 prices) opened up by drifting on the 300-foot and 500- foot levels. It is clear that no comprehensive picture of the structure was had at this time. The orebodies were considered to be very irregular pods scattered through masses of quartzite-carbonate in a sheared zone about 800 feet wide. In some way the ore was believed to be related to the tuff-slate contact zone. With this picture it was impossible to make a reasonable ore estimate or even gauge the tonnage potentialities with any feeling of reliability."

Jan 1, 1949

By M. E. Holter

"Five main lignite seams occur in the Tertiary Ravenscrag Formation in the Eastevan area, at depths of 100 feet or less. They are named, in ascending order: the Boundary, Estevan, Souris, Roche Percee and Short Creek seams. A total sequence of approximately 250 feet is represented by the coal beds and interstratified clays, silts and sands. Strata dip to the southeast at 25 feet per mile or less and trike northeast. Large areas underlain by coal seams at shallow depths are delineated. Reserve calculations are dependent on detailed information on seam thicknesses and feasible stripmining depths. The stratigraphically higher seams are thinner on the average than lower seams and this, together with the increase in elastic size fractions in higher strata, suggests a retreat of a Tertiary marine margin to the south during the closing depositional history of coal seams and associated strata."

Jan 1, 1972

By L. M. Pidgeon

Abstract The production of metallic calcium, by reduction of lime with aluminium, was investigated. Using a modified form of the effusion method, the vapour pressure of calcium above the reaction: 4CaO + 2Al ~ 3Ca + CaO.AI203 was determined and found to vary from 1.0 to 1.3 mm. Hg from 1,150° to l,200°C. From the magnitudes of the various thermodynamic quantities involved, together with a consideration of the known chemical characteristics of the reaction, it was suggested that the reaction proceeded by reduction of lime with aluminium vapour. INTRODUCTION The conventional production of metals by reduction of their ores by carbon (or carbon monoxide) may be represented by the equilibrium: MO+ R [] RO+ M . . . . . . . . . .(1) where MO represents the metal oxide, and R the reducing agent (carbon or carbon monoxide). The free energy change ?F° associated with the reaction is given by -?F° = RTlnKp . . . . . . . . ... . (2) where R is the gas constant, T the absolute temperature, and KP the equilibrium constant. It should be noted that ?F° represents ? the standard free energy gained by the system and hence -?F° is the free energy gained by the surroundings - and that as ?F° increases K must decrease, and conversely. For metals above manganese in the electromotive series, the ?F° associated with reaction would quantity and from it can be seen that this corresponds to a small fraction for K. The equilibrium pressure of the oxide of carbon represented by RO is then too near its concentration in the furnace gases for the reaction to proceed in an internally fired furnace. For the practical reduction of such metals, fuel fired furnaces are inadequate. Electric furnaces may be used to give higher temperatures with lower concentration of carbon oxides and the reaction may still proceed. However, for many metals such as calcium and aluminium the formation of stable carbides or acetylides may prevent production of the metal by this reaction. In this case, either electrolytic methods must be used, orrecourse must be had to reducing agents other than carbon. It is the latter method which is under consideration here.

Jan 1, 1948

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004