Search Documents

By Jasmin Raymond

Ground source heat pumps are used to heat or cool building and heat water supply. Such heat pumps use the earth as a heat source or sink to efficiently provide or store thermal energy. For example, a ground source heat pump typically requires less then a third of the electric or fossil fuel energy of a conventional heater. Ground source heat pumps could therefore help reduce the energy consumption of active mines where low-grade geothermal resources are abundant. In most heat pumps, water or a water-antifreeze mixture having a temperature ranging from -6.5 to 43.5 °C is circulated through a heat exchanger at a rate of 0.000033 to 0.000067 m3/s (2 to 4 L/min) for each kilowatt of heating/cooling capacity. The groundwater that is continuously pumped to drain mines could be used to operate heat pumps. Water feeding a heat pump can alternatively circulate in a close loop network of pipes buried underground or installed in a surface water body. Retention water ponds, tailings and waste dumps commonly found at active mine sites could provide excellent environments to install the close loop system. Further research will help take advantage of the unexploited geothermal resources associated with actives mines.

May 1, 2007

By D. Van Tonder, C. Edwards

ABSTRACT Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium-bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares seven of these options on the basis of typical capital and operating costs for the solvent extraction circuit and downstream uranium processing and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.

Jan 1, 2013

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By L. C. Lien

Tower crane layout (TCL) is a typical construction site layout (CSL) problem, which is suitable for a wide range of work assignments and site conditions. Tower crane is one of the key facilities for vertical and horizontal transportation of materials, especially for heavy prefabrication units such as steel beams, ready mixed concrete, prefabricated elements and large panel formwork such as machinery and equipment, and a wide variety of other building materials within a construction site. However, it is a difficult combinatorial optimization problem to determine the locations of tower cranes with materials quantity supply and demand for engineers. Swarm intelligence (SI) was very popular and widely used in many complex optimization problems which was collective behaviour of social systems such as honey bees (bee algorithm, BA) and birds (particle swarm optimization, PSO). This study applied a hybrid swarm algorithm namely particle bee algorithm (PBA) based on a particular intelligent behaviour of honey bee and bird swarms by integrates theirs advantages. This study compares the performance of PBA with BA and PSO for a proposed hypothetical construction engineering of TCL with materials quantity supply and demand problem. Results show that PBA performs better performance than the mentioned algorithms on a proposed hypothetical TCL problem.

Aug 1, 2013

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

By L. Klatzel-Mudry, D. J. Nikols, J. D. Hughes

"The Geological Survey of Canada Paper 88-21, A Standardized Coal Resource/Reserve Reporting System for Canada, is referenced by National Instrument 43-101 for the preparation of resource and reserve estimates on coal deposits. However, for all disclosure of mineral resources or mineral reserves for coal, issuers are required by NI 43-101 to use the equivalent mineral resource or mineral reserve categories set out in the CIM Definition Standards and not the categories set out in Paper 88-21. “Because the framework is based on Canadian deposits and their tectonic regimes, the Canadian Securities Administrators believe it is not reasonable to apply Paper 88-21 to foreign coal properties. The “Resource Links” at the end of this volume provide website links to guidance documents for preparing coal resource and reserve estimates in Australia, South Africa, and the USA.”This report discusses definitions, concepts and parameters used to determine coal resource and reserve quantities, and provides a framework to facilitate consistent categorization of coal quantities found within various depositional and tectonic regimes in Canada.Coal deposits, or portions thereof, are first categorized in terms of their geological complexity <Geology Type), and probable recovery method (Deposit Type). Methods for determining quantification parameters including seam thickness, areal extent and bulk density are outlined for each geology/deposit category. Within each geology/deposit category, coal resources are further divided, based on their assurance of existence, into measured, indicated, inferred and speculative subdivisions and, according to their feasibility of exploitation, into immediate and future interest subdivisions. Coal reserves within each geology/deposit category are subdivided according to whether they are within or outside active mining areas, and may be reported on in place, recoverable and saleable bases.A wide cross-section of the coal industry in Canada contributed to the development of this reporting system. To ensure that the parameters and concepts expressed in the system continue to reflect technological and economic realities in the future, the Coal Association of Canada has established a committee to facilitate periodic reviews."

Jan 1, 2003

"Developed by CRIRSCO, IRT is a document that draws on the best of the CRIRSCO-style reporting standards. These reporting standards are recognised and adopted world-wide for market-related reporting and financial investment.The IRT is not an international reporting code and does not supersede existing national reporting standards. Rather it is a guideline that encapsulates the content of these standards for the benefit of the international mining industry and its various stakeholders.The template is a 'living document' that is continuously updated and improved as new national laws, rules, codes and guidelines are created or amended.The International Template is advisory only and where national codes already exist, these will take precedence. The International Template is intended to assist those countries that either do not have a reporting code or whose code is outdated, to produce a new code consistent with international best practice. It also provides a consolidated version of national codes that reflects their compatible international components and may thus be used in comparisons with other international reporting systems. The word 'Template' is used advisedly to indicate that this document is a model for code development and does not in itself constitute a 'code' which implies that it has legal or other regulatory force.From this point forward, the Template includes words that imply a mandatory action, such as ""requires"", ""applies"", ""must"" etc. This is to enable the Template to be easily adopted by countries and organisations wishing to do so, and does not imply that the Template itself is a mandatory reporting standard.INTRODUCTION2 In this edition of the International Reporting Template (""The Template""), important terms and their definitions are highlighted in bold text. The guidelines are placed after the respective Template clauses using indented italics. They are intended to provide assistance and guidance to readers for interpreting the application of the clauses in the Template.Indented italics are also used for Appendix 1 — 'Generic Terms and Equivalents"", and Table 1 —'Check List of Assessment and Reporting Criteria' to make it clear that they are also part of the guidelines for the application of the Template.Appendix 1 contains a table of generic terms and their equivalents, designed to avoid unnecessary duplication or ambiguity in the textAppendix 2 provides Rules of Conduct for Mineral Resource and Mineral Reserve estimators that may be considered in addition to the Codes of Ethics or Practice normally applying to members of professional institutions."

Jan 1, 2003

By Stefan Boshkov

THE ADVENT of mining at great depth has brought to the fore the question of stresses around mine openings. The many-pronged attack on this problem is certified by the accelerated appearance, in the mining literature, of articles on various topics related to this subject (1). Whereas it may be agreed that we, of the mining profession, have fallen woefully behind in research and the development of an understanding of this important facet of the general problem of mining, it must also be accepted that the analysis of the stresses in a mine structure is usually more complex than is the case in the majority of structures encountered and dealt with in civil engineering. Whereas homogeneity and isotropy are readily acceptable for most metals, such properties are but crudely approximated in rocks. Whereas the external loads on a structure in civil engineering may be readily determined, those on a mining structure are subject to ?conjecture. Whereas the limits of the structure may readily be defined in civil engineering, the boundaries of the mining structure are, in most cases, indeterminate, and subject to intelligent guesswork, at best.

Jan 1, 1956

By O. K. Mahabadi, A. Lisjak, B. S. A. Tatone, N. Vlachopoulos

"Numerical simulations are widely adopted in the design of several types of rock structures, including tunnels, caverns, rock cuts, and open pit and underground mines. In recent years, analyses based on the hybrid finite-discrete element method (FDEM) have been shown to provide a realistic representation of rock mass deformation and fracturing processes. To date, the FDEM approach has successfully yielded qualitative and quantitative results for several practical rock engineering applications, yet it has lacked the ability to consider the implementation of rock-reinforcement measures. Since rock reinforcement is often used in civil and mining applications to improve the strength and deformational behaviour of a rock mass, the ability to incorporate such features into FDEM analyses is essential to extend its applicability to a broader range of problems. The work presented in this paper represents an important first step towards developing a simulation tool that can be used for practical rock engineering applications, including the design of underground excavations and rock slopes.INTRODUCTIONRock support and reinforcement measures are often employed in civil and mining rock engineering projects in order to maintain or improve the strength and deformational behaviour of rock masses. The preferred type of reinforcement or support elements along with the preferred layout and timing of installation depend on the in-situ ground conditions, the nature of the rock mass and excavation method. Over the last two decades, numerical modelling has been increasingly used to design and attempt to optimize rock reinforcement and support systems. As such, most rock engineering-specific modelling software now offers various approaches for modelling different rock reinforcement and support elements."

Jan 1, 2015

By Mike Fontaine

The success of a project is defined by meeting the financial performance objectives of the business case within a stipulated timeframe. Early in design, little information is normally available; the uncertainty introduces risk to the project outcome. Using a range of risk management tools and techniques, a project can be developed from front end loading phases 1 through 3 (FEL1–FEL3), and project implementation (FEL4) and then into operations with an optimized probability of success. For every project element, the risk management framework embodies: establishing a context; assessing risk (identify, analyze, and evaluate); and treating risk. Embedded within design activities, this process mitigates or eliminates risks. Monitoring and control, as well as extensive communication and consultation with stakeholders, is integral to the risk management process.

Jan 1, 2015

Most of automotive magnesium applications are presently produced by high-pressure die casting processes, For further expansion of the alloy usage in automobiles, novel-manufacturing processes needs to be developed, In this study, squeeze casting of AM50 alloy was carried out using a hydraulic press with an applied pressure of 70 MPa, Tensile properties and fracture behavior of the squeeze-cast AM50 were characterized in comparison with the die cast counterpart, The squeeze-cast AM50 alloy exhibits virtually no porosity in the microstructure evaluated by optical microscopy, The results of tensile testing indicate that the improved tensile properties for the squeeze-cast samples over the conventional high-pressure die-cast parts, The analysis of tensile behavior shows that the strain-hardening rate during the plastic deformation of the squeeze-cast specimens is constantly higher than that of the die-cast specimens. The SEM fractography evidently reveals the ductile fracture features of the squeeze-cast alloy AM50.

Jan 1, 2005

By Louis Frost

"A FIRE which forced the sealing -of the east side of Dominion No. 16 Colliery in the Town of New Waterford, Nova Scotia, occurred on October 6th, 1952 (Figure 1).So far as can be ascertained, the fire was first noticed in the roof of No. 7 East Lateral, after a brushing shot had been fired in the pavement. There appears to .be no doubt that this shot •blew out, igniting a small feeder in the roof.Regular air measurements and air samples, taken over a long period prior to the fire, indicated that the ventilation was adequate, for at no time had the percentage of CH4 in the general air current exceeded one per cent in this location. The last regular monthly samples and air measurements, taken at the end of September, showed the condition of the ventilation to be:Return at the Top of No. 8 East WallQuantity .... 27,700 cu. ft. per min.CH4 .......................... 0.32 per centC02 ................................ 0.10 per centHowever, in the week preceding the fire the mine examiner on four occasions had reported small feeders of gas at the face of the brushing in No. 7 East Lateral.Figure 2 is a diagram of the working place where the shots were fired. The face brushing had been shot down at 3 :45 p.m. and cleaned up. Two 'hurdle screens' had also been erected, one close to the face brushing and the other fifteen feet from the face."

Jan 1, 1953

By I. Spector

A SHORTAGE of cement in the Prairie Provinces, together with an aggressive policy on the part of the Saskatchewan Government in bringing new industries to the province, combined to create a favourable set of conditions for the establishment of Saskatchewan's first cement plant on the outskirts of Regina. Built by Saskatchewan Cement Corporation Limited, this single-kiln plant, tl1e latest addition to cement producers on the Prairies, began operations in the Fall of 1956. Location of the plant followed the trend of building cement manufacturing facilities in market areas rather than at raw material sources. In 1957, all assets of the Corporation were taken over by Inland Cement Company Limited and the plant and quarry now operate as Saskatchewan Cement Company, an Inland division. The Regina plant's production makes up approximately eleven per cent of the productive capacity of all plants in the Prairie Provinces. At present, two types of cement are manufactured -normal portland and sulphate resisting.

Jan 1, 1960

By D. S. Speakman

The copper-zinc orebody at Sherritt Gordon&apos;s Ruttan Mine occurs in a structurally complex area of the Rusty Lake greenstone belt in northern Manitoba. Problems in interpreting drill results indicated a large deviation, and the structural complexity an erratic deviation, of drill holes. This was confirmed when a surface hole was intersected 420 feet to the left of line on the 800 level. This problem acted as a catalyst in promoting a search for a suitable down-hole survey method. The instruments investigated included magnetic multishot and gyroscopic units as well as the ABEM Reflex-Fotobor. Only the Fotobor came close to meeting the company&apos;s needs of simplicity, reliability, accuracy and ownership. In this paper, the methods of operating this instrument, as well as the data extraction and reduction techniques, are described. Data on the accuracy and repeatability of the instrument are presented, and a tabular presentation of the results of surveying on 86 holes totalling 64,000 feet of drilling is made. Preliminary statements of the results of ongoing research on causes of hole deviation are presented and recommendations for minimizing deviation are given. The use of the survey device is recommended in areas of structural complexity, for very steep or backsight holes and where expected ore intersections are missing.

Jan 1, 1978

By F. Melo, M. Pawlik

Fine coal aggregation in concentrated coal-water suspensions was studied through steady-state rheological measurements. The wettability of coal particles was modified by dry oxidation of a bituminous coal. The degree of hydrophobicity was monitored using film flotation. The rheological measurements revealed that hydrophobic coal particles aggregate in aqueous suspensions, over a wide pH range, and produce slurries with high yield stresses. As the degree of coal oxidation increases, the coal particles become more hydrophilic and such suspensions exhibit lower yield stresses values. The yield stress values for suspensions prepared from oxidized/hydrophilic coal become a strong function of pH and correlate well with the surface charge as determined through electroacoustic measurements. These results indicate that the yield stress of aqueous suspensions of coal, and hence coal particles aggregation, is strongly affected by the wettability of coal particles.

Jan 1, 2004

By S. Mathieu, R. Mennillod-Blondin, P. Cousin, N. Valle, H. Bouzahzah, P. Marion

The gold deposit of the Lapa mine has a complex mineralogical gold state with coarse and fine native gold, aurostibite and submicroscopic gold within arsenopyrite. A specific mineralogical characterization of the refractory fraction was conducted combining various techniques such as optical microscopy, electron microscopy, electron microprobe and secondary ion mass spectrometry. In parallel, the mineral processing behaviour and the recovery of the refractory gold were studied by pressure oxidation and cyanide leaching. This paper presents the mineralogical methodology developed to characterize the refractory gold distribution within arsenopyrite. These results are presented and interpreted in order to plot gold recovery versus sulphide oxidation. The comparison of the metallurgical behaviour yields predicted from the mineralogical data and the one calculated from leaching tests shows a good agreement and allows mineralogical explanations of the gold metallurgical behaviour.

Jan 1, 2011

By H. Oterdoom, S. Pilger, T. P. Bui, J. Rotarius

"Most FeNi furnaces used to rely on post-combustion and off-gas cooling inside the furnace to eliminate the produced CO gas, and control the off gas temperature. As furnace load, capacity, and thus gas volumes increased over the years, this led to increased instabilities that can cause problems in controlling the operation. Some of the large capacity furnaces nowadays work with partial or full combustion outside the furnace, more similar to the steel industry. Forced combustion with or without enriched air and other additions can support in controlling post-combustion, stabilizing and even reducing off gas amounts, and affecting composition. This paper presents some of the possibilities and advantages of having a specially designed post-combustion system for the FeNi laterite industry, but that could also be applied to other processes as well.Large Scale Furnaces In the FeNi industry, the Rotary Kiln Electric Furnace (RKEF) process is still going strong in spite of continuous hope that hydrometallurgical processes will one day make the RKEF plant obsolete. Within the pyrometallurgical plants there is a continuous trend for larger scale furnaces. The development for a number of furnaces that were started before 1985 and increased capacity by “natural growth” is given in Figure 1. Natural growth refers to the development of the plants that after having mastered a certain level of operation, were ready for a higher load that could be installed either with a new furnace on the same site, or during a revamp. The advantages of natural growth are numerous, for example: •,Deep knowledge of the ore and its’ behavior, no need for testing, and little risk of surprises. •,Mining, laboratory, equipment, etc. is all proven technology for the conditions on site. •,Starting a furnace with increased capacity is a re-start, not a green-field commissioning. •,Typically, when increasing the production capacity of an existing plant, not the entire plant is commissioned for the first time, but only a part. In the FeNi laterite industry for example, the kilns may already have had the capacity to provide enough material."

Jan 1, 2017

By C. R. Whittemore

PROGRESSIVE industrial organizations have recognized the importance of maintaining an adequate reference library of volumes covering all phases of their particular branch of industry, but it has been the experience of the writer that few engineers know how to use to the best advantage this store of extremely -valuable information which has been accumulated for their service. Nor does the average engineer appreciate the fact that it is only through the current technical literature that he can keep abreast of the rapidly developing fields of engineering. The present-day ramifications of the engineering field are of such wide scope that the human mind is not capable of storing away more than a small fraction of the information available on any particular topie; yet, from time ? to time, such information would prove invaluable. An engineer can know intimately only a small part of his own branch of engineering; but he cannot afford to neglect to take the fullest possible advantage of all that is already known in his own particular field. Technical information may be obtained by one or more of the following methods: (1) by enquiring of the individual who knows; (2) by performing the experimental investigations necessary to ascertain the facts; (3) by consulting the technical literature, where a record may be found of the work of others. This last method is the one we wish to examine. Our main consideration is the question of how to use the library, but first it is necessary to give some attention to the kind of enquiries one takes to the library, and to the nature of the sources of information available.

Jan 1, 1938

By E. G. Charlesworth, M. J. Robertson

"Abstract - Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots.Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confined largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semi­ massive sulfides within tension fractures which are folded, attenuated and fractured .An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994

By J. S. Moretzsohn, D. F. Graham

"Airborne Synthetic Aperture Radar (SAR)was acquired over the Carajás Mineral Province, within the rainforests of the Amazon, which hosts the world’s largest Fe-ore deposit(Santos, 1986). Significant chemical weathering exists in this humid environment. PrevalentAu mineralization is thought to be generally associated with deformation zones in Archean schists.Radar data have proven to be very useful as an aid to geological mapping in the tropical rainforests of the Amazon Basin in Brazil. In these densely vegetated areas, a sense of regional structural trends is obtained as a con-sequence of the sensor/terrain geometry. The top forest canopy is the main terrain reflector of X-band radar energy, and consequently is the main terrain surface feature expressed in processed radar imagery. Radar is important for extending t,he continuity of mapped structural lineaments. Differential weathering is related to variations in radar image texture which is used to infer gross lithologic variations and relative age relationships of major rock units. Specifically, quartzites and banded iron formation are highlighted in the radar imagery due to their unique tonal and textural appearance, in contrast to schists, gneisses and metavolcanic rocks. As tropical areas are typically enveloped in cloud or mist, radar data are invaluable in providing information for logistical planning of field mapping activities."

Jan 1, 1997