Search Documents

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985

By M. R. Dion, K. Frenette, R. K. Jonas, S. Simard, F. Robichaud

"In 2011, a site study indicated that the application of Honeywell’s Multivariable Predictive Control Technology (MPC) to the Goldex processing facility would provide significant opportunities for improvement. Grinding MPC was implemented in the SAG Mill in June 2015. This pilot application, called Phase 1, featured one of the first Multivariable Predictive Controllers to be installed in a Canadian mineral processing plant. Since the implementation of MPC, gold recovery from the gravity circuit has increased. MPC contributed to a decrease in flotation feed particle size (120 to 112 µm) and an increase in the SAG feed tonnage (8.5% increase). MPC also increased and stabilized the % solids of the SAG feed, which can have an impact on cost reduction (mechanical maintenance). Additionally, MPC increased productivity, providing grinding operators with more time to perform other tasks. Further anticipated benefits include the standardization of the grinding circuit operation from one team to the next, thereby minimizing circuit disturbances resulting from different operating philosophies. This paper will discuss the advanced control project development and justification, the technology and rapid implementation process, the performance results and the benefits obtained.IntroductionGoldex is an underground mine located near Val-d’Or that is owned and operated by Agnico Eagle Mines Limited (AEM). Between 2008 and 2011, mining focused on the Goldex Extension Zone (GEZ). In 2011, the project was halted due to geotechnical problems; operations ceased until late 2013. Goldex operations resumed in September 2013 with the M and E zones, for which there were 0.7M gold ounces of proven and probable reserves, 2.1M ounces of measured and indicated resources and 1.2M ounces of inferred resources, totalizing 4M ounces. Life expectancy was extended until 2024."

Jan 1, 2017

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

By A. H. Mumin, A. K. Somarin, K. S. Oran

"Synvolcanic structures played a fundamental role in the genesis, morphology, and siting of volcanogenic massive sulfide ores and associated hydrothermal alteration in the Archean South Sturgeon Lake caldera complex. The most voluminous and persistent hydrothermal venting and massive sulfide deposition occurred along synvolcanic rifts and grabens associated with faults and tectonic fissures that created permeable fracture zones deep enough to access the underlying hydrothermal reservoir. The type of fracturing is highly variable and changes with the composition, competency, degree of consolidation, and alteration of host rocks. Synvolcanic structures and fracture styles also vary according to the amount and type of tectonic movement, including extension-related collapse, shearing and faulting perpendicular to the principal direction of extension, and orthogonal faulting and shearing. Permeable conduits were created by tension fracturing along fault zones, brittle deformation at the intersections of orthogonal faults, and by extensional fractures in stockworks. In texturally uniform footwall rocks, the distribution of alteration zones was controlled by the morphology of the structural conduit. In rocks with vertical and/or lateral facies, permeability, and competency changes (e.g., Lyon Lake graben), there was an additional stratigraphic control over fluid migration. Some crosscutting synvolcanic structures, alteration zones, and intrusions appear as stratiform units at the present erosion surface due to regional deformation and the present attitude of the volcanic stratigraphy.Hydrothermal mineral assemblages (e.g., quartz, carbonates, chlorite, pyrite, chalcopyrite) infilling structurally induced fractures provide good evidence of fluid migration pathways. However, mineralogy can vary significantly according to the fluid characteristics, host rock geochemistry, and subsequent metamorphic history of the area.Clearly, one of the best methods for locating volcanogenic massive sulfide deposits is to delineate the attitudes of synvolcanic structures, and explore those that show evidence of associated high-temperature hydrothermal mineral assemblages. Excellent exploration targets occur where synvolcanic structures with hydrothermal alteration intersect paleo-seafloor horizons."

Jan 1, 2007

Improved Process & Practices Result In: ? Reduction of undesirable downtime, & expensive secondary damage ? Improved equipment performance & health ? Extension of equipment life, & reduction of operating costs ? Safety and environmental performance improvement Equipment knowledge capture and consistently applied

May 1, 2010

By CIM Environmental, Social Responsibility Society

Within the mining industry, the pathway from exploration, to planning, construction, operation and closure has become more complex over the last few decades. The current financial, environmental and social influences present the mining industry with unprecedented challenges and opportunities. In addition, international environmental and social reporting standards and codes are becoming increasingly robust. The reporting requirements provide an added impetus for issuers to effectively manage environmental and social impacts and risks. Reporting requirements also provide the opportunity to be transparent. The intended audience for these Environmental, Social and Governance (ESG) Guidelines for Mineral Resource and Mineral Reserve Estimation includes practitioners, industry participants at all levels of skill and experience, corporate management and board members, government agencies, academic institutions and interested parties. For practitioners, this document provides underlying key principles of environmental, social and governance practices. The ESG Guidelines provide guidance for those using environmental, social, governmental and governance information when preparing and implementing mineral exploration programs and contributing to the preparation of mineral resource and mineral reserve estimates for mineral properties that are either at the study stage (i.e., scoping / preliminary economic assessment, pre-feasibility, or feasibility studies) or in operation. The guidelines can also be used to help mineral resource and mining companies apply good practice to manage their environmental and social risks and opportunities. Companies can identify and retain appropriate professionals to prepare environmental and social materials to support company studies. The guidelines are also a resource for companies developing effective environmental and social management strategies at any project stage. This document is not intended to be prescriptive and is not intended to provide exhaustive guidance on what to consider in terms of environmental, social, legal and governmental modifying factors in the preparation of MRMR estimates. Rather, it is intended as general guidance to assist companies and practitioners in considering and applying these modifying factors for MRMR estimates. This document is also not intended to guide environmental and social impact assessment (ESIA); however, the measures needed to manage impacts help inform the constraints and costs for defining mineral resources and mineral reserves and inform the costs and schedules of mineral project studies. All documentation of MRMR estimates made by an issuer and intended to be, or reasonably likely to be, made available to the public in a jurisdiction of Canada must comply with the requirements of National Instrument 43-101 Standards of Disclosure for Mineral Projects (NI 43-101), as amended from time to time (Canadian Securities Administrators, 2016a and 2016b). Disclosure is not addressed in these ESG Guidelines. Determination of what to include in disclosures is defined in the applicable Securities’ legal frameworks. Appendix A presents a summary table showing the linkage of the principles and topics in these ESG Guidelines to the potential effects on project costs, schedules, government permits and approvals, social licence to operate and financing.

Sep 8, 2023

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By Stratton-Crawley R., G. E. Agar

"A study has been done of the scale-up of laboratory bench-scale flotation to continuous plant circuit performance. It was found that the impellor speed and the air flow rate influenced the results and in this case extreme values of these operating variables were required in order to reproduce the plant rougher results in the laboratory. Despite the experimental uncertainty introduced by these extreme values, it was demonstrated that the plant performance could be predicted and experimentally reproduced with bench-scale tests.IntroductionThe mineral processing industry relies heavily on batch flotation testwork to design flowsheets, evaluate reagent s and compare various types of ore. The batch tests are generally regarded as being directly comparable within themselves, but quite often they relate poorly or not at all to continuous circuits. Obviously this dilemma generates considerable uncertainty with wide-ranging ramifications. One of the manifestations of this unfortunate situation is the commonly expressed opinion that ""it may work that way in the laboratory, but it will never work that way in the plant"".In a previous publication, a method was described whereby the results of batch bench-scale tests could be used to simulate a locked cycle flotation test series. The work to be described here is a continuation of that investigation with an extension to the simulation of an actual plant circuit. It would have been preferable to progress from laboratory batch data to a continuous pilot plant and then finally to a full-scale plant operation. However, because that possibility did not present itself, an attempt will be made to show that the performance of an existing plant circuit can be successfully simulated from batch data. The success of the procedure can be judged by the agreement among the plant results, a locked cycle test and the predicted results based on batch tests."

Jan 1, 1982

By E. Henry, C. Mayer, H. Rott

Hangingwall deformation monitoring at Kiruna mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening toward the town of Kiruna. In the quest for more effective monitoring techniques, LKAB decided to evaluate the ability of satellite-borne synthetic aperture radar (SAR) interferometry to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the mining industry. This paper describes the basic principles of SAR interferometry and describes how subsidence is monitored at Kiruna mine. The encouraging results are discussed as well as the benefits (continuous deformation mapping, low cost, fast, etc.) and limitations (sensitivity to snow and vegetation cover) of the technique.

Jan 1, 2004

By Jochen Petersen, Diane Taggart

"At an average of 90.3% (for the period of 1 January 2009 to 30 September 2011), Zincor’s zinc recovery was well below the industry standard of 96%. The losses through the residues, in particular the iron residue, were the biggest contributors to the overall zinc loss. It was believed that this loss could be decreased with the implementation of seed recycling. A plant trial was run to test the implementation of a seed recycle. The rate of seed addition through recycle was increased over a 4-week period. The presence of seed decreased the insoluble zinc loss by providing additional surface area for iron to precipitate onto, and reducing coating of unleached neutralising agent. The soluble zinc loss was also decreased at low and moderate seed recycle volumes. The improvement was attributed to agglomeration growth of the recycled particles, which improves the dewatering characteristics of the precipitate. In contrast, the soluble zinc loss increased at high seed recycle rates. This result was attributed to particle crowding and a low wash ratio.INTRODUCTION The Zincor refinery, which closed in December 2011, was situated just outside of Springs in the Gauteng Province of South Africa and employed the conventional Roast-Leach-Electrowin process, which accounts for 75 to 80% of the annual primary zinc production in the world. The refinery fed up to 220 000 t/a of zinc sulphide concentrate. The major portion of the raw material was sourced in Southern Africa from the Rosh Pinah and Black Mountain mines. Between 20 000 and 40 000 t/a of material was imported to make up the deficit and to improve the grade of the feed material. The iron contained in the zinc concentrates, at an average of 6.03% (for the period of 1 January 2009 to 30 September 2011), resulted in the formation of zinc ferrite during roasting, which is insoluble under atmospheric leach conditions. At Zincor, most of the zinc ferrite was dissolved in the residue treatment plant at elevated temperature and high acid strength. The leach liquor from this aggressive leach contained between 15 to 30 g/L of iron, mostly in the ferric form, and was known as the hot iron solution (HIS). The presence of iron in the liquor had an adverse effect on the zinc operation, particularly on the current efficiency in the electrowinning circuit. Therefore the iron needed complete removal."

Jan 1, 2016

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By Rick Wilkins

The stability of steep embankments is a major safety issue in open pit mining, highway passes, and earth filled dams. A failure in any one of these situations could mean a loss of very expensive equipment, a long term inconvenience, and more importantly, a loss of life. These possible catastrophes could be avoided by installing a reliable real time monitoring system. Robotic total stations (RTSs) give one possible cost effective solution to creating a near real time monitoring system. Repeated surveys at predetermined time intervals can automatically generate warnings if slope movements exceed a preset tolerance level. The variation in atmospheric refraction, combined with possible instabilities in reference targets, can make a monitoring system based on RTSs produce false alarms. A methodology has been developed at the Canadian Centre for Geodetic Engineering (CCGE) for reducing these systematic error effects. The methodology has been realized in the creation of a software package that has been successfully implemented at large earthen dams in California and at an open pit mine operation in British Columbia.

May 1, 2002

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

By F. Dai

Granitic rocks usually exhibit strongly anisotropy due to pre-existing microcracks induced by geologic loadings. The understanding of the rock anisotropy in mechanical properties such as tensile strength is critical to quarrying and stabilization of underground structures. In this paper, Brazilian tests are conducted in combination with MTS material testing machine and split Hopkinson pressure bar (SHPB) system to measure both static and dynamic tensile strength of anisotropic Barre granite. Samples are cored and labeled using the three principle anisotropic directions of Barre granite (BG). These directions are also chosen as the loading directions for the Brazilian discs. For dynamic tests, pulse shaping technique is used to achieve dynamic equilibrium in the samples during the test. Finite Element Method is implemented to formulate equations that relate the failure load to the material tensile strength employing a orthotropic model for Barre granite. For samples in the same orientation group, the tensile strength shows clear loading rate sensitivity. The tensile strengths exhibit clear anisotropy under static loading; while less anisotropy under dynamic loading. The tensile strength anisotropy of Barre granite is interpreted as interactions of the pre-existing microcracks.

May 1, 2009

By Jérôme Girard, Shiu Kam, Sue Longo

"Historically, tailings management in a northern climate has involved the deposition of tailings into the Tailings Management Area (TMA) as conventional slurry. This type of system is obviously viable but presents challenges that are difficult to manage as circumstances change over the life of mine. These issues can include:? Increases in mill throughput, and? Life of the TMA for the life of mine.This case study will present how thickened, high-density, non-segregating tailings are used as an alternative to conventional slurry disposal to achieve greater storage capacity and enhanced environmental performance for a gold tailings facility in a northern climate. This paper will focus on how this change in deposition strategy accommodated the increased throughput of the mill and the increased life of mine. Specifically, the paper will discuss the addition and integration of new processes to the exiting mill system to accommodate the tailings management issues. It will highlight the challenges from laboratory testing to pre-feasibility to the engineered design of the thickened tailings system implemented at Musselwhite Mine.BACKGROUNDGoldcorp Canada’s Musselwhite Mine, in Northwestern Ontario (120 km north of Pickle Lake), is an underground gold mining operation that began production in 1997. The current mill throughput is about 4000 tpd (1.4 Mtpa). Gold extraction is based on a CIP process with cyanide destruction.The existing tailings management area (TMA) is located about 2 km southwest of the mill complex. The TMA is contained by high ground to the north and to the west and flanged by a moraine ridge along the south side. A number of dams have been constructed along this ridge. The dams were first built in 1996 and subsequently raised in 2000 and again in 2005. Excess tailings pond water is discharged to a polishing pond then released to the environment via a wetland.The TMA was originally designed to contain 13.7 Mt of tailings under a ponded surface for closure. The water cover was to inhibit adverse long-term environmental effects because the tailings contain pyrrhotite and other sulphide-bearing minerals that are potentially acid generating. The design was modified during Stage 3 Construction in 2005 to expand the storage capacity to 17.3 Mt (Golder, 2005). As of end of 2009, over 16 Mt of tailings had been deposited in the TMA. The slurried tailings were historically deposited at 50% solids."

Jan 1, 2011

By Robert E. McIvor

The Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By Don Thompson

It isn?t a lie if you don?t tell the whole truth The pictures National Geographic didn?t print Other photos National Geographic didn?t print?

May 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

May 1, 2009