Search Documents

By L. M. Amaratunga, G. G. Hein, D. N. Yaschyshyn

Fine tailings produced in the milling process have traditionally been disposed of in tailings ponds. Attempts have been made to use these fine tailings in backfill, however, to date the majority of backfill operations have utilized only a small percentage of fines. The remaining fines are, therefore, being sent to tailings ponds creating a waste disposal and environmental problem. This disposal practice is even more acute in the gold milling industry where fine grinding, required for value liberation, results in the production of large quantities of fine tailings, of which a large percentage cannot be used in backfill. Through Cold-Bond Tailings Agglomeration (CBTA), these fine tailings can be agglomerated into pellets which can then be used as a coarse aggregate in back-fill. This paper presents the results of using these pellets to create an Agglomerated Tailings Paste Fill (ATPF) made entirely of fine gold mill tailings and cementing binders. Through this process, supplementary imported aggregates such as sand, gravel, rock-chips are not required while still maintaining adequate back fill strength. By using this CBTA technology, fine tailings are diverted from tailings ponds and becomes utilized as a value added resource in the form of aggregates for use in paste fill.

Jan 1, 1997

By T. Holmes, S. Davison

"The Special Standard Surge bin at Agrium’s Vanscoy Potash Operations (VPO) has been plagued with flow problems and wear, and corrosion issues for it’s entire working life. Investigation showed that the carbon steel construction, bin geometry, and resultant funnel-flow pattern were directly responsible for production losses and disproportionate maintenance and capital costs. Potash enters this bin at between 140°C and 165°C, but the stagnant potash outside the active flow channel was much cooler, allowing moisture to migrate toward the outer regions, which caused corrosion of the walls and reduced live capacity as the potash in this area hardened and built up on the walls over time.A 2013 inspection revealed holes and paper-thin areas in the lower cylinder wall sections and in the conical hopper. The only thing preventing major leaks and even a potentially catastrophic failure was the buildup of stagnant hardened product on the cone walls. It was concluded that the cone had reached the end of its life and required replacement. VPO’s original plan was to replace the cone in kind and repair the cylinder as necessary; however, a failure-mode and bin-performance investigation combined with a lifecycle- cost analysis indicated it would be better to redesign the hopper.For success in retrofit projects, it is essential at the design stage to consider the bulk solid flow properties and the operating environment involved. Because education in this area is not offered at a university level, engineers often do not fully appreciate the effects of the flow properties of bulk solids on bulk material handling equipment.Jenike & Johanson conducted flow properties tests on samples of potash and using the data, redesigned the bin and the feeder. After the modifications, VPO’s surge bin provides safer, more reliable operation with a much longer predicted working life. Using this retrofit as an example, we aim to provide a general understanding of bulk solids flow theory and highlight the importance of customizing the design to the appropriate flow properties in the cost effectiveness, reliability, and safety of a bulk material handling system."

Jan 1, 2016

By Francis Perron

The Directive 019 on mineral industry, which was officially adopted in 1989, is the main tool used by the Quebec Ministry of Environment for the environmental evaluation and control of mineral exploitation projects presented for approval. This document contain the environmental guidelines which must be met by all the mineral companies during and after exploitation. The Directive 019 also contain all the information required by the Quebec Ministry of Environment in order to fully analyse the environmental impacts caused by the mineral projects proposed to the Ministry for approval. The proposed modifications of the Directive 019 cover many new topics that were not addressed in prior editions, these include : water recirculation, groundwater protection, tailings management and post exploitation environmental controls.

Nov 1, 2002

By H. W. Smith, C. L. Lewis

"A process control computer has been installed in the Lake Dufault concentrator to: (a) control the on-stream X-ray analyzer and convert chart readings to elemental percentages, (b) calculate the flow rates required for the most important flotation reagents, using the amount of material entering the process, the analyses and the slurry pH, and (c) set the reagent feeder to these flow rates automatically. Although this project was largely experimental, to gain knowledge and experience in flotation process control, the objectives have been met and fully automatic computer control is now the normal mode of mill operation.This paper describes project planning and defines the system with respect to both control design and functional design. System operation -as seen by the mill operator -is detailed. Implementation of the system is described and the system is discussed in terms of its success, economic justification and future plans."

Jan 1, 1969

By C. R. Fast, G. C. Howard

The loss of fluid to the formation adjacent a fracture governs the areal extent of the fracture and the success of hydraulic fracturing as a production stimulation technique. The three flow mechanisms which control this loss are the result of the viscosity of the fracturing fluid and the permeability of the formation to the fracturing fluid, its wall building properties, and the combined effects of viscosity and compressibility of the reservoir fluid. The effects of these flow mechanisms can be evaluated in terms of a fracturing fluid coefficient, the fundamental concepts of which are developed in the paper. The fracturing fluid coefficient, which may be used in calculating the areal extent of fracturing, affords a direct measure of the effectiveness of fracturing fluids. The area of hydraulically created fractures is in-creased as the coefficient is de-creased. The fifteen-fold variation noted in this coefficient for the commercially available fracturing fluids tested resulted in a six-fold difference m the calculated areal extent of the fracture system.

Jan 1, 1961

By E. J. Marcotte

"INCO LIMITED'S Shebandowan Mine and Mill is located in a scenic tourist and cottage area near the western tip of Lower Shebandowan Lake, approximately 90 Km west of Thunder Bay, Ontario. This nicely designed complex is a positive indication that mining operations can co-exist in harmony within the natural environment.The Shebandowan complex processed nickel-copper ore from 1973 to 1985, inclusive, after which operations were shut down.In late 1988, INCO LIMITED decided to place the Shebandowan complex back into operation, under contract, to mine and mill the remainder of the ore body, according to their specifications. MaclSAAC'S EXPLORATIONS was the successful bidder for the project. Following preliminary rehabilitation, operations were re-activated in late March, 1989. The ore mined to date is of a moderately lower nickel grade than the majority of previous years. However, a higher tonnage rate, combined with improved nickel recoveries, has contributed to a viable operation.A series of mill operating and equipment modifications has enabled MaclSAAC EXPLORATIONS to achieve the quality and grade of nickel-copper concentrates specified, and at the same time, expand mill tonnage throughput while attaining increased nickel recovenes."

Jan 1, 1992

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By W. E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential."

Jan 1, 2002

By T. L. McCall

AUTHENTIC records show that coal mining in Cape Breton dates from the year 1720, when the French military authorities obtained coal from what is now known as the Blockhouse seam, in the Morien district, for use at Louisburg, where the fortress, now of such historic interest, was being built. Thereafter, coal was mined more or less continuously, and although, for many years, in a very haphazard way, there was, on the whole, a steady growth towards a better regulation of the industry, culminating in the year 1825 with the arrival of the General Mining Association in Nova Scotia. This Company, more generally known as the G.M.A., had acquired extensive tracts in Brazil and Colombia and had also purchased the mining rights for the whole of Nova Scotia-excepting such areas as had been previously leased-the attraction being the rich veins of copper currently reported as occurring in the Province. These fabulous copper veins, upon examination, failed to materialize, but the engineer sent out to report on them returned with such good accounts of the coalfields he had seen that steps were taken immediately to investigate them. From that rime onward, the history of coal mining in Nova Scotia is one of progress and achievement. One of the first acts of the G.M.A. was to acquire the areas already leased to other concerns and develop these in a masterly fashion, employing the best machinery and talent available at that time. Such dominant control over the minerals of the Province, although it led to orderly development in the several coalfields, also, later on, resulted in restricting operations in the various coal centres to such an extent that a determined effort was put forward by the people of Nova Scotia to end such a state of affairs. Consequently, in 1857, the original lease of the G.M.A. was abrogated, the Company, however, being allowed to retain certain areas in the districts it had already developed. This opened the way for the formation of other coal-mining companies, and numbers of these immediately sprang into existence in the various coal-mining centres. In 1893, the Dominion Coal Company, Limited, was formed by the amalgamation of seven companies operating in the neighbourhood of Glace Bay, in Cape Breton. Later, in 1910, the Dominion Iron & Steel Company, Limited, obtained control of the Cumberland Railway & Coal Company, which had been formed in 1884 to acquire the rights of the two companies working in the Cumberland County coalfield.

Jan 1, 1936

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

The major factors limiting the establishing of vegetation on the shale and sandstone wastes at Minto are high exchange acidity and low pH (shale pH 4-5, sandstone pH < 4). In the first revegetation program (1967-74), 3.8 million trees were planted without grading on 4,000 acres (red, jack and scots pine and black locust). White dutch and sweet clover, birds-foot trefoil and red top were established in selected areas, and ponds were stocked with brook trout. In the second phase of reclamation, beginning in 1979, a comprehensive plan will be initiated which will allow for forest production, wildlife development and recreational activities.

Jan 1, 1977

By Abhiram Shankar

Construction projects are becoming more demanding both in terms of time and complexity. This necessitates intricate planning and sequencing of activities at the macro and micro level and continuous flow of resources across the project in order to achieve planned targets. Work and Resource planning need to be done in such a way that limited resources give optimal output. Currently dominant activity-based scheduling techniques like Critical Path Method (CPM) and Program Evaluation and Review Technique (PERT) do not model work-flow or resource-flow through a project life cycle. An extension to the conventional activity based planning is Location Based Management System (LBMS). LBMS has been explored and utilised in the case of repetitive and cyclic projects such as high rise buildings. This study focusses on the application of LBMS to repetitive and non-repetitive components of Power Transmission and Distribution (PT&D) projects involving construction of substation and cable laying. This paper presents the findings on comparing the current planning practice for cable laying with an LBMS based approach. A key finding of the study was that the conventional practice resulted in a schedule with several coordination issues that could not be identified in the planning reports. Using the LBMS based approach these issues could be identified and decisions required for resolving these could be made.

Aug 1, 2013

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is con-?ned by tectonic shear zones between marble and metapelites, extending laterally into the marble astabular, pod or lenticular oreshoots (up to 50 m x 20 m x 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical pro?les across mineralized zones con?rm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the in-situ supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly in?uenced by seasonal ?uctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent ?ooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2~10-3.8 to 10-1.4) and oxygenated (fO2~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sul?des and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+was transportedinto karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Abstract-Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is confined by tectonic shear zones between marble and metapelites, extending laterally into the marble as tabular, pod or lenticular oreshoots (up to 50 m ?? 20 m ?? 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical profiles across mineralized zones confirm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the insitu supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly influenced by seasonal fluctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent flooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2 ~10-3.8 to 10-1.4) and oxygenated (fO2 ~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sulfides and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+ was transported into karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2 in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2 increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By The Satff

"TEXADA Island is situated in the Strait of Georgia, about 100 miles northwest of Vancouver. The property of Texada Mines Ltd. lies on the southwest coast of the northern end of the Island. A part of the ""Sunshine Coast,"" the climate is moderate, with about 30 inches of rain during winter months and relatively dry summers. Texada has been shipping high-grade magnetite concentrate continuously since 1952 to Japanese ore buyers. In 1959, a 3,000-foot tunnel was driven just above sea level to explore the possible downward extension of known orebodies then being mined by open pit. In January of 1961, because the open-pit operations had a limited life, C. C. Huston and Associates were brought in as mining consultants to do a feasibility study on the possibility of going underground for production. This study was completed in March, 1961. With the completion of the report, the Company went to Japan seeking a ,long-term contract to justify the capital outlay necessary for setting up an underground operation. Concurrently, underground diamond drilling revealed more ore, and the Company planned some modifications to the concentrator for increasing the copper recovery. By November, 1961, a ten-year contract was signed with Japanese ore buyers for the sale of 450,-000 long tons of concentrates beginning in October, 1963. Since that time, the Company has built its own 65 000-ton ore carrier and an additional three-year contract has been negotiated, with an annual tonnage increase of from 450,000 to 550,000 tons."

Jan 1, 1967

By X. (Mike) Yao

Rock mechanics engineers must provide ground support designs that ensure a safe underground working environment. Unexpected falls of ground are unacceptable while ground support systems must be adequate. Ground support must be economic for the area supported and the time frame the opening is in use. While numerical modeling can be used for ground support design, empirical models are still the common useful design tools. Empirical models are best developed and improved from local experiences although some models, such as Stability Graph (Potvin et al, 1992), are in extensive use by the Canadian mining industry. To determine the adequacy of ground support practices at HBMS, a database of 50 fall of ground case histories between 1985 and 2001 was compiled. For each failure, the recorded data included: location, rock type, rock mass conditions, opening and failure geometry, installed ground support and failure mechanism. An analysis of the database was done to obtain an understanding of failure frequency association with rock types, stope geometry and installed ground support, and to assess what support design changes were necessary. The paper describes changes made to ground support and mining practices during the last five years, and the formation of new ground support standards and practices which have been successful in reducing ground falls while providing improved, efficient and economical ground support.

May 1, 2002

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit&apos;s maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By E. Özberk

Uranium minerals are often associated with iron minerals, and during the hydrometallurgical processing of the uranium ores, iron plays several significant roles. The presence of Fe(III) in solution promotes the oxidative acid leaching for the recovery of uranium. The control of the distribution of impurities in milling and refining is also affected by dissolved iron. When rejected from the process streams, iron usually collects other impurities and contributes to the stabilization of the wastes for final disposal. These roles of iron, as they relate to current uranium processing operations, are discussed in detail, and some broad and historical perspectives are also presented.

Jan 1, 2006