Search Documents

Epithermal deposits have been defined as the lower temperature end of a spectrum of hydrothermal mineral deposits and are inferred to have formed near the EarthÆs surface. The preservation of an epithermal gold deposit in an Archaean craton is rather problematic, especially when such deposits form clusters or groups as reported for the Pilbara and Yilgarn cratons. For two of the better studied examples of epithermal gold deposits in these cratons, Becher and Wiluna, the evidence that they formed near the Earth surface is non-diagnostic, and the epithermal origin appears uncertain. Despite the simplicity of the original definition, there have been numerous errors in classifying epithermal gold deposits. It is suggested that these errors are primarily due to poor criteria defining the group as there is limited evidence of poor observational science being the cause. The criteria being used to recognise epithermal gold deposits include tectonic setting, ore element suite and quartz vein textures. None of these are diagnostic of epithermal deposits and their link back to the original low pressure-temperature definition of the class is tenuous. There has been definition creep over time as new observations on potential epithermal gold deposits become accommodated within a flexible definition. There is some urgency establishing and then using criteria to reliably identify epithermal deposits. Distinction of epithermal gold from weathered gold deposits is an important step. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Luck D

Current methods of mucking out small development tunnels are a major limitation to improved efficiency and high rates of advance. This is particularly true in the deep metalliferous mines of South Africa, where the harsh environment, remoteness of operations and the hard abrasive rock conditions mitigate against the use of the tunnel borer type of equipment. The Loader Distributor Train was designed to overcome the special problems of hard rock tunnelling. It combines advanced innovative technology with proven simple methods of operation and maintenance. The system aims at taking advantage of new, efficient and cost effective power sources in South African mines based on replacing compressed air with electro hydraulics and the new concept of hydropower. It also introduces electronics and computer technology, for both automatic control and fault finding, into the production environment. The system is designed to permit sophisticated equipment to be operated and maintained by a semi skilled labour force. Although still undergoing trials it is believed that the Loader Distributor Train will prove highly effective, and that the new concepts offer considerable potential in areas other than flat tunnels, in particular the cleaning of inclined shafts.

Jan 1, 1986

By Hancock RG, Dewar GJA

The mining and exploration industry is governed both directly and indirectly by a complex and constantly changing regulatory and legal system, yet few technical professionals realise the extent to.which they are affected and that they are personally liable for any breaches. These breaches may result in criminal or civil prosecution that could involve significant financial penalties (to the extent that all personal assets are at risk) and even imprisonment. Generally, a professional at risk should be able to mount a due diligence defence in order to avoid or mitigate these consequences. Mineral property and company owners, directors, managers and employees are at risk, as are consultants, contractors and suppliers of equipment or consumables. Whilst all are liable for their personal decisions to act (or failure to act) in managing operations or carrying out directions, as well as for the actions of others under their control, the focus here will be on the exposure of the consultant. Consultants are usually driven by an internal desire to perform to a high standard because of personal pride in their work and concern for their professional reputation. However, there are an increasing number of external requirements for them to be able to demonstrate, if necessary, that their actions were based upon reasonable grounds and that their work conformed to current best practice standards. If they cannot do so, they may face potential personal Liability.

Jan 1, 1995

Mining projects draw together stakeholders with various degrees of experience in managing and assessing financial risk. When this risk is not fully appreciated or quantified, the potential for making decisions not suited to investor requirements is significantly increased. A feasibility study provides key information on project development potential, requiring detailed technical investigations with thorough financial analysis. Centaur Mining and Exploration (CME) owned and operated Cawse Nickel Operations (CNO), one of three Australian projects to develop and process vast amounts of near surface nickel resources. A technical ædue-diligenceÆ and æbankable feasibility studyÆ confirmed the large resource base, newly applied yet tested technology and relatively low unit costs would produce nickel in the lower half of industry operating costs. A number of production variables including capital requirements, delayed start-up, nickel grade, processing, maintenance and product output were outside the feasibility estimate. This was combined with exchange rate fluctuations and lower Ni prices. The inability to generate adequate cash flow and service debt repayments ultimately led to receivership and liquidation of all assets. Following the sale of CentaurÆs gold and nickel divisions, $A 784 million remained outstanding to creditors. This paper aims to define key issues leading to CNOÆs collapse by reviewing feasibility parameters, valuation methodology and project development. Some methods of assessing project viability are discussed with the aim of increasing stakeholder risk awareness.

Jan 1, 2003

By Willis G. M

Preliminary experiments have shown that, when used in a fusedchloride electrolyte, titanium carbide anodes dissolve yielding lower titanium chlorides which nlay be electrolysed in situ to produce a cathode deposit of pure titanium metal. The anode residues are easily withdrawn from the cell. Further experiments have established the operating conditions for maximum efficiency in the process.The process is essentially two-stage, viz.: (1) titanium carbide production, (2) electrolysis producing metal. Power requirements appear to be moderate and this fact, combine·d with the simplicity of the process make it attractive as a possible method for the production of titanium.INTRODUCTIONDue to the high reactivity of titanium and its, affinity for oxygen and nitrogen, the extraction of this metal generally involves the use of halide. compounds as intermediates. For instance, magnesium reduction of titanium tetrachloride is the basis of the well established Kroll process and electrolysis of the lower chlorides in a molten salt bath has been proposed by Cordner and Worner (1951, p. 358) and others (Brenner and Senderoff, 1952, 223C; The TitaI Company (Inc.), 1952) as means of production of the metal. Thedifficulty of preparation of these compounds prompted a search for an alternative extraction process. The fact that aluminium, an equally reactive metal, has been prepared by electrolysis using aluminium alloy anodes suggested the possibility of a similar process for titanium production.The Titan Company (Inc.) (1952) has patented the use of crude titanium metal anode, but it was thought possible that a metallic compound, such as the carbide, could be used for this purpose. Although Lorenz and Kaufler (1909) suggested the use of carbide anodes for metal production, no...

Jan 1, 1956

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electrolyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions.The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was investigated as a method of optimising glue additions in the presence of antimony.Scanning electron rnicroscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltarnmetry measurements showed some correlation between current efficiency and activation polarisation potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1988

By J C. Furness, F S. Cannon

Metal casting operations are a significant source of hazardous air pollutants. In particular, high production iron foundries emit significant quantities of volatile organic compounds (VOCs) during pouring, cooling and shakeout of iron castings made in green sand molds. End-of-the-pipeline capture and destruction methods to reduce VOC emissions add crippling costs to foundries. Alternately, the incorporation of advanced oxidants (AO) into metal casting green sand systems has been shown to reduce emissions from high production iron foundries in the US, and at the same time reduce operating costs. Cost savings are driven by the benefits of AO in clay recovery systems. Emissions reductions are the direct result of cascading AO-based reactions taking place in green sand molds. This sustainable greening of the metal casting process is a prototype for the development of other AO and non-AO process-based solutions for sustainable high temperature processing of materials. Fundamentals of AO technologies will be discussed along with the performance characteristics of AO processing systems in the metal casting industry and the breadth of other processing and remediation applications for which AO technologies have the potential to be successfully employed.

Jan 1, 2002

The reduction of titanium tetrachloride to trichloride can be achieved by employing hydrogen and electric arcs. It is possible to produce melts containing up to 50% TiCk in the eutectic mixture of LiCl/KCl by striking a D.C. arc at the surface in the presence of hydrogen and TiCl. vapour. If the electrode IS made to just penetrate the surface of the salt mixture, a hot zone results from the' high resistance contact with both lower chlorides and sintered titanium may be produced. The sintered metal forms just below the melt surface while the trichloride forms at the gaslIiquid junction.The "hotspot cathode" appears to offer a solution to the problem of producing coherent deposits as the spong'e metal can 'be continuously withdrawn in a similar manner to the "calcium process".INTRODUCTIONConsiderable interest has been shown for some years in the possible development of a cheap electrolytic process for the extraction of titanium metal, since a method using simple materials and cheap electric power would materially reduce the cost of production. Even when cheap starting materials are used, however, there exist several general difficulties in the operation of plant which both limit the speed of production and increase the cost of the product. It happens that most of the techniques so far tried produce a powder as cathodic deposit, and when this is the case the following difficulties arise:1. The whole contents of the bath must be treated with solvent in order to extract the 'metal powder which may itself tend to oxidise, and thus become contaminated.2. Fine metal powders, which often contain residual entrained salts, are less easy to consolidate by arcmelting than metal sponge.

Jan 1, 1956

The basic model for the evaluation of any coal-bearing property is the cash flow projection, the major components of which are operating costs, capital charges, taxation and revenue. A range of cash flow projections can be produced by varying the assumptions which underlie the operating costs, by assuming various forms of capital funding, by making assumptions as to future taxation and by speculating upon the present and future market value of the product. As for any model, the informational inputs and assumptions are vital because, no matter how sophisticated the processing, the informational inputs and assumptions cannot be improved by it. That is to say, the validity of the output (the total evaluation itself) cannot be of greater certainty or significance than that of the inputs. The total evaluation can of course be expressed in a number of ways such as the Discounted Cash Flow (D.C.F.) Rate of Return, the Net Present Value or, the Payback Period. The foregoing statement may seem trite. However, it is necessary to be clear about it so as to avoid unnecessary complication and a preoccupation with techniques as opposed to the informational inputs and assumptions. So far as techniques are concerned, much has been written and said about them during the last decade. Most of us have heard, if not always understood, something about probabilistic models, Monte Carlo simulation, sensitivity and risk analysis to say nothing of inflationary costing and the relative merits of developing cash flows in terms of current or constant money. Those techniques have their value, particularly if they can serve to illuminate conclusions which could not be reached on a simple and even perhaps on an intuitive basis. I am, however, reminded of one major coal mining project in which 20 or more major variables were identified, many cash flow projections were run on the computer and a detailed sensitivity analysis was carried out. The major conclusion reached was that the D.C.F. Rate of Return was predominantly sensitive to variations in selling price and operating cost. Of course, the funding and fiscal elements of a cash flow projection have to be dealt with as rigorously as possible. However, in the development of any coal property, capital requirements and taxation are, in part at any rate, dependent upon the assumed operational parameters. If the latter are misjudged, the whole evaluation process is deeply affected. The same is true of revenue, in the sense that, the positive cash flow is a function of output as well as selling price and again, misjudgements about achievable and maintainable levels of production also deeply affect the final evaluation. I shall try to underline the fundamental influence of the technological factors upon lead times, capital costs, operating costs, taxation, funding and the achievable and maintainable levels of production. In turn, these affect the whole question of coal property evaluation and indeed, the likely success or failure of any coal mining venture. I make no apology therefore that this paper does not set out to discuss the more esoteric aspects of the evaluation process but rather, directs attention towards some of the informational inputs and assumptions which merit clarification and discussion.

Jan 1, 1975

By Laajalehto K

The basic condition necessary for flotation is hydrophobicity of the surface of the mineral to be floated. For sulphides, this condition usually requires treatment with a collector solution. The conditions for this treatment have until recently usually been chosen by the trial and error principle which has indeed been working relatively well under favourable conditions; ie for simple homogeneous ores. However, the present tendency to increasing use of complex and often relatively lean ores sets increasing requirements for the control of the flotation process. This development is the reason for the present rapid development of process control methods in flotation. In addition to the already well-established practices of pH and reagent feed controls, the importance of measuring and controlling the electrochemical potential of the ore particles to be floated is recognised in the case of sufficiently conductive minerals. In fact, the electrochemical potential seems to be the basic quantity determining the flotation behaviour of such relatively well-conducting minerals as sulphides. Since the hydrophobicity of the mineral and, hence, its flotation properties are ultimately determined by the composition and structure of its surface, information on these under different process conditions is important for design and operation of efficient flotation processes. The basic requirement set for the methods used for obtaining this information is high surface sensitivity of the method. The recent rapid development of surface characterisation has produced several methods which fulfil this requirement. Their application to the problem of characterising surfaces of mineral samples in contact with collector solution is, however, often complicated. The main reason for this is the vacuum environment necessary for the measurement. In the case of flotation experiments this means that in most of these methods the measurement cannot be made in situ, but the sample must be extracted from the liquid and subsequently evacuated in the vacuum chamber of the instrument. It is essential to carry out these steps so as to avoid to the extent possible changes in the sample surface. For the purpose of establishing whether this has been accomplished it is important to compare the results of methods operating in vacuum with some available in situ method. An optimal choice of methods seems therefore to be a combination of the available powerful vacuum methods with in situ measurements. The most usual combination seems to be X-ray photoelectron spectroscopy (XPS or ESCA), Fourier transform infrared spectroscopy (FTIR) and electrochemical measurements. This choice combines the unique possibilities for direct elemental and chemical characterisation offered by XPS (Cecile, 1985) with the in situ capability of FTIR and electrochemistry. In the XPS measurements, it is essential to apply a special sample handling technique to avoid loss or damage of some sensitive species of the collector-based layer on the mineral surface. In the following will be given some examples of the application of the XPS technique in combination with electrochemical methods of sample treatment to studies of the layer formed on sulphide substrates in ethyl xanthate (EX)

Jan 1, 1993

By Ho-Tun E, Stewart PSB

The definition and recognition of silver minerals is very difficult. In general such minerals occur at low concentration and can be hard to identify and measure using conventional optical mineralogy. The present paper describes the use of the QEM*SEM system to tackle this problem and provide information of use to the metallurgist. Three aspects of QEM*SEM are used to special advantage in this application. Firstly the automated mode of operation is used to make a rapid search for the sparse phases. Secondly the X-ray capability is used to identify the mineral phases. Finally the image analysis programs quantify the distributions of the minerals which are found. The paper deals with the identification stage of the process and with the use of the data which can be derived. Silver minerals which covered a range of ore types and composition were collected and studied in detail. On the basis of these measurements and information received from a number of mining companies regarding the important minerals, a classification table was prepared. This table listed about 40 different silver mineral types which could be identified by QEM*SEM and which were of interest in silver recovery processes. Where the silver occurs in solid solution in concentrations greater than about one per cent, the silver content in the species was subdivided into ranges based on statistical intervals. The QEM*SEM system was programmed to recognise these as separate species. Examples are presented of the use of the system in defining the type and morphology of the silver mineralisation to assist in the assessment of batch flotation test Samples.

Jan 1, 1993

By M Roberts

The aim of this paper is to evaluate the technical feasibility of application of the electric monorail as a haulage system in hard-rock underground mining in Australia, in comparison to conventional truck haulage systems. The elements of the system being investigated include mine design and layout, installation, loading and unloading subsystems, tramming speeds, cost and productivity, automation, ground support, safety and environmental factors. Electric monorail systems are potentially more cost-effective due to a range of factors: only the one system may be needed for the transportation of workers, material and rock; and excavations for monorail haulage can be smaller and mined at much steeper gradients than for truck haulage. The smaller excavation size also reduces the need for costly ground support and û in another important measure for the health and safety of mine workers, and for energy savings û it reduces ventilation requirements. Electric monorail haulage technology is being applied in hard rock mines in South Africa and considerable benefits have been realised by the industry in that country. In Australia, mine designs for metal mines generally remain based on truck haulage and/or shaft hoisting systems. There is a tendency to apply these haulage systems to every orebody. For the industry to achieve sustained growth against a backdrop of volatile diesel prices and environmental concerns, new generation underground haulage systems are required. The monorail haulage system offers opportunities in improving materials handling efficiencies in underground mining operations. This paper examines the application of monorail haulage in metalliferous underground mining, presents comparative data with track and trackless haulage systems and develops concepts for system application in combination with conveyor belt haulage and narrow vein mining situations.

Jan 1, 2005

By S R. Grano, M Vera

This paper deals with two separate case studies investigating the froth phase performance and characterisation of two industrial rougher/ scavenger flotation circuits. Froth phase performance was quantified using a mass balance approach to estimate froth zone recovery. Measured characteristics of the froth phase included frother solution concentration determined by gas chromatography, and the time taken for an equilibrium froth sample to decay to one-half of its original froth height. The latter measurement is referred to as the æfroth half-lifeÆ and is strongly linked to froth stability. Special methods and techniques developed to preserve frother in solution and to measure froth half-life are briefly described. The frother type in the first case study was a mixture of straight and branched alcohols, whilst the frother type in the second case study was a mixture of alcohols, aldehydes and triethoxybutane. The first case study focussed on a flotation circuit treating a low-grade ore containing only a small fraction of floatable copper sulfide minerals, while the second case study focussed on a flotation circuit treating a higher grade complex sulfide ore containing significant quantities of chalcopyrite, galena, sphalerite and pyrite. It was found that froth zone recovery of valuable mineral generally decreased down-the-bank of the two industrial rougher/scavenger circuits. Moreover, decreases in froth zone recovery significantly limit the overall cell recovery of valuable mineral achievable from the plant scavenger cells. However, the decrease in froth zone recovery could not be linked to the removal of frother from the pulp solution to the concentrate product in the preceding rougher flotation stages. Measurements of residual frother in solution suggested that, approximately, only five to ten per cent of the added frother was removed into the rougher/scavenger concentrate, with the remainder appearing in the scavenger tailings. This finding suggested there was apparently adequate frother in solution in the scavenger stages.

Jan 1, 2005

Timestudy analysis of mining operations at North Broken Hill Limited has been carried out by dissecting operations into small elemental components, and accurately timing these elements. Over a wide range of observations, this has enabled standard time values to be calculated for all underground work.The application of the standard values is in calculating performances as a measure of work output and Performance Controls are kept on approximately two-thirds of underground employees. Through the Controls it has been possible to stimulate supervisory action to improve low performance, and to reduce delays and lost time.The values are used to calculate contract" prices, and anomalies in previous prices have been adjusted on work values and not on arbitrary standards. In out-of-the-ordinary circumstances, the request for a timestudy investigation has been made by both operatives and foremen, and the contract set following the timestudy analysis has been to the satisfaction of both parties.The range of values enables contracts to be applied to work which was previously performed on a day basis, resulting in improved performance.A natural corollary of timestudy is the analysis of methods, and in some cases method improvements have been introduced.It is anticipated that further investigations will be made on methods.INTRODUCTIONIn 1953, a Timestudy analysis of mining operations at North Broken Hill Limited was commenced under the guidance of management consultants. Its aim was, to determine standard time values for specific operations, which would provide management with a measure of productivity beyond the existing measures of tons or feet of advance, and also to determine whether increased output was available under existing operating conditions.

Jan 1, 1956

By E Haren, A Winchester

The CSA Mine has a long and varied history from initial discovery in 1871 through to the present. Lead-zinc mineralisation was mined historically near the surface. Today copper and silver are extracted from the deeper regions of the mine. The mine has passed through a number of owners over this time, each with a unique operating philosophy and understanding of the mineralisation. Cobar Management Pty Ltd re-opened the mine in 1999 and has undertaken extensive drilling programs to expand the resource and gain a better understanding of the mineralisation characteristics. Presently mineralisation has been located over a strike length of 1.2 km and to a depth of over 2.0 km with over 30 mineralised lenses from four identified ore systems. The refinement of geological and mineralisation models led to further discoveries and prompted a review and modification of resource modelling processes. Advanced statistical analyses prompted the implementation of ordinary kriging as a grade estimator. Improved stationarity from enhanced geological domaining has been supported by variography and kriging neighbourhood analysis studies. Resource models at CSA are now quantifiable in terms of mineralisation style and estimation reliability. The new techniques are assisting the definition of more mining fronts, which are creating new opportunities to increase mine output.

Jan 1, 2006

By Hawes GW

Until 1980 copper, lead and zinc sulphide slurries have been success- fully dewatered for rail and sea transport for many years at the Rose- bery site of North Broken Hill Holdings Ltd. utilizing conventional vacuum disc filtration systems. An upgrading and mill expansion program completed in 1981, which also permitted the introduction of ore streams changes, had resulted in difficulties dewatering copper and lead sulphide slurries to comply with transportable moisture limits. Following an extensive investigation which included both laboratory and pilot plant testing a program was commenced to replace the 2 vacuum disc filtration systems with 2 pressure filtration systems for use on copper and lead slurry dewatering and also to retain other existing vacuum disc filters as standby. An analysis of mill operations performance resulted in slurry storage tanks with a capacity equivalent to 20 hours of normal production being incorporated into the project. The pressure filters are mounted above the concentrate stock- piles. A sealed sloping floor incorporating launders is used to prevent any accidental contamination of the concentrate from pipe leakages, spillage, or from water hoses used for clean up purposes around the area. The project was completed in 1985 and operating performance has been better than that predicted from testwork. Equipment availability at 95076 together with the slurry storage capacity provided results in minimal requirement for the standby vacuum filtration system. Some typical operating results are given.

Jan 1, 1988

In this paper presented are the criteria used when assessing the harmfulness of shocks affecting the buildings. Those criteria are based on the value of speed or accelerations of building vibrations. Presented is the scale of harmfulness of vibrations of Langefors and Kihlstrom, Bureau of Mines, and SWD contained in the Polish Norm PN-85/B-02170. The parameters of the mining shocks measured by the Lubin coal mine station were compared with the parameters calculated as per the correlations (regression curves). The average acceleration calculated from the correlations for eight measurements is only two per cent higher than the actual one. But the average frequency of vibrations calculated from the correlations for eight measurements is as much as 2.22 times lower than the actual one. In order to analyse whether that takes place in the whole range of the energy of shocks compared were the results of calculations from the correlations for various magnitudes of shocks and various distances from their epicentre with the results of the measurements. From that it follows that only for the shocks of the highest energies the lowering of the frequency of vibrations by two times causes movement from the higher zone of harmfulness to the lower one (for example from the IV to III). In the one-family houses in Lubin there were the damages that are characteristic for not only for the III but also for the IV sphere of harmfulness as per the SWD scale. That should be explained via further research and maybe it would be feasible to draw out a new correlation to determine the frequencies only for high values of energy of shocks and determine the preciseness of the acceleration and frequency correlations used presently.

Jan 1, 2003

By A Richmond

"In some lode-style gold deposits the geological (lithological) uncertainty may have similar economic significance as the grade uncertainty. In the absence of precise knowledge of the deposit geology, geological models of these types of deposits that are used to constrain spatially the estimated (or simulated) grade values may influence significantly the contained metal. Methods for assessing geological uncertainty quantitatively are rarely considered due to their perceived inability to consider exhaustive geological interpretations, and resulting models that often appear geologically unrealistic. Furthermore, should the lodes have been subjected to folding, or where the mineralisation continuity does not follow a planar orientation along strike or down dip, standard methods of variography and interpolation using linear vectors in space often do not provide a good representation of continuity. An alternative approach is to relate spatial samples from adjacent drill holes using an unfolding plane.The paper demonstrates conditional simulation of the geometry and gold grades of a folded lode-style deposit where:simulation of lode geometry considers explicitly the geologistÆs interpretation, andsimulation of gold grade values that consider explicitly the folded nature of the lodes.The results are contrasted to the traditional approach of linear vectors in real space for a single lode interpretation.CITATION:Richmond, A, 2012. Conditional simulation of a folded lode-style gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

Mineral resource estimation is commonly based on the accumulation of a series of local estimates. At times, the distribution of these grade estimates is not appropriate to the grade distribution of the data on which the estimates are based. Mineral resource grade estimation has an increased potential of being in error as the grade variability increases. As the mineral commodity value increases, greater grade variability within the mineral resource is tolerated. This paper directs its attention to mineral properties where the data average grade is 20 per cent or more than the data median grade at a specific cut-off grade. A mineral resource estimate is enhanced if it is supported by graphs which demonstrate that the sample data have been separated into appropriate geological domains. Each geological domain has a unique grade distribution signature, which can be graphically demonstrated simply and objectively. This signature will usually be evident well before the Indicated mineral resource estimates are available. The paper looks at the use of the log probability and MedAve plots to assess how effective domaining has been. It further outlines how the MedAve plot can be used to assess the integrity of the mineral resource grade estimate within a geological domain with the data on which it is based. The paper suggests that the overall grade of a mineral resource at any cut-off grade will be closer to the data median grade rather than the data average grade. Tips are provided to ensure that the odds reflected in the data grade distribution are not ignored and hence the risk that the project is affected by unrealistic estimates of the overall mineral resource grade is reduced.

Jan 1, 2003