Search Documents

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By B Cooper

During the design of a new production facility for a greenfields or significant brownfields expansion many design decisions are made driven by an unquestioning objective to achieve 'lowest cash-cost' production costs. In many cases this translates to a design and operating philosophy based on largest-available, single-line equipment. Although acknowledged as an approach that is efficient from an operating cost perspective does this approach always maximise shareholder value? There is an increasing awareness in the mining industry of the value of project flexibility, robustness and value options. The design of a new production facility creates a window of opportunity which should be structured to ensure that project value options and robustness are understood and exploited. This requires the use of emerging valuation methodologies, such as Value-at-Risk and Real Options, as well as tried and trusted NPV/IRR approaches. The paper provides an overview of the basis and application of these less well known techniques in the context of metallurgical plant design. Design guidelines that demonstrate how value options and flexibility can be quantified from both a risk and value perspective are presented. Issues such as use of single versus multiple line equipment, optimum cut-off grade and improved exploitation of the inherent variability of the orebody are also examined. Finally the management issues and approaches to achieving this will be briefly discussed; for example it is common during project development to drive towards increasing certainty as rapidly as possible to facilitate 'accurate' estimation of costs. Understanding and exploiting value options requires a project culture that tolerates, and revels in, ambiguity and uncertainty û something that would make many project teams uncomfortable!

Jan 1, 2008

Mining of the silver-lead-zinc orebodies at the George Fisher Mine officially started in 2000. A review of mining performance to date shows that many of the extracted primary stopes have experienced some degree of hangingwall dilution. The degree of hangingwall failure in the stopes became progressively more extensive throughout mining of the orebodies in 2001 and 2002, culminating in the unplanned catastrophic failure of the 744D stope in which the ore between 13C (2683RL) and 12L (2714RL) sublevels caved into the previously mined cavity between 13L (2654RL) and 13C sublevels. This was followed several months later by another unplanned caving event in a nearby stope, 740D. As a direct result of these unplanned failures it was decided to mine the stopes with a smaller span than had been previously planned and in a primary-secondary pyramidal stoping sequence. To limit the exposure of the stope hangingwall, a hangingwall drive is no longer developed and therefore geologists no longer have access to the detailed geological information that this provided. Geologists at George Fisher Mine have had to be adaptable and flexible in response to these proposed changes and rely more on data from drilling than mapping for their geological interpretation. The result is that the drilling cycle has become much more critical in the planning process.

Jan 1, 2003

By M Noppe, I Glacken

There are many critical nodes along the mine value chain, from orebody to mineral product, and inter-disciplinary input is required to analyse the variability and uncertainty at each node in order to identify and mitigate areas of risk. Mining differs from many other industries in that the variability in the product is dictated largely by the inherent nature of the input material (the orebody). The true characteristics, including the variability of the orebody, are never known exactly and are instead based on estimates derived from sample data. A further difference is that bottom-line gains are largely controlled by world commodity prices, which can vary with time, rather than by local supply and demand issues. Methods for identifying, reporting and responding to this inherently variable raw material are discussed. These include analytical and reporting methods, equipment and software, risk analysis and reality checks (eg reconciliation). Sampling results, mineral resource and ore reserve estimates and economic assumptions are a function of the variability of the orebody. Risk quantification should be expressed as a level of confidence, which takes into account the scale or period over which the risk is being assessed (life-of-mine, annual or shorter production periods) and should convey the likelihood, severity and consequence of occurrence of a given event. The future generation of mining specialists needs to understand the entire mine value chain to better manage risks and maximise mine dollar-value.

Jan 1, 2002

A comprehensive understanding of the rocks associated with coal seams, and also of the coal itself, is essential in assessing the likely behaviour of the materials before, during and after the mining process. The nature of the rock materials involved in coal mining can give rise to risks from adverse geomechanical properties, create problems in coal quality control and produce difficulties with environmental impacts, all of which may affect the profitability, impact and safety of the operation. Examples of issues associated with rock composition include slaking and degradation leading to roof, floor, pit wall or spoil pile instability, ignition of methane in mine atmospheres by frictional processes, liberation of quartz-rich dusts into ventilation systems, production of coal with unfavourable preparation or marketing characteristics, and escape of suspended solids or potentially toxic leachates from spoil piles and other types of emplacements. Methods for evaluating rock composition include microscopic examination, chemical analysis and X-ray diffraction, with the latter being especially useful for fine-grained rocks or for clay-bearing materials. Other techniques, such as geomechanical testing and down-hole geophysical logging, are also useful, but give less direct information about the actual composition of the materials involved. Indeed, understanding of rock composition, through microscope or quantitative X-ray diffraction studies, provides a basis for checking information from other sources, explaining different aspects of rock behaviour, and an essential link in relating geophysical or geotechnical data to broader-based geological models as part of the risk assessment process.

Jan 1, 2003

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

The Central Andes in Peru, Chile, Bolivia, and Argentina, contain two contiguous terranes which were accreted i, Gondwanaland between the end of the Devonian and the end of the Triassic. These terranes, Arequipa in the north, anni Chilenia in the south, differ from each other in the timing and style of their metallogenic development. However, they contain over 90% of the Central Andean porphyry copper resource. The copper porphyries in the Arequipa terrane are Paleocene to lower Oligocene in age, whereas the Chilenia deposits are mid-upper Cretaceous and mid-upper Miocene. Porphyry copper deposits occur outside these terranes, but are all Miocene in age. Miocene porphyry-style mineralisation also exists in the Arequipa terrane, but is copper-deficient and gold-rich. The accreted terranes may have favoured porphyry and other styles of copper mineralisation because they possessed relatively thin continental crust compared to adjacent parts of the Andes. Crustal thickening which commenced at about 30 Ma in the Arequipa terrane coincided with a major change to polymetallic, precious metal mineralisation which commonly displays high sulfidation charcteristics.

Jan 1, 1995

By Broome A

In a technologically oriented industry, it is important to understand and apply technology very consciously to create competitive advantage. Technology is not an activity which is simply restricted to CSIRO or the research and technology department. Technology improvement is a part of everyone's role. It is a way of life - the technology facet of continuous improvement. For this reason, The AusIMM has organised this Travelling Technology Forum - a series of presentations about automation in mining. To make the message more accessible, The AusIMM had originally planned to take the Forum to four regional mining centres: Mackay/Townsville, Singleton, Burnie and Kalgoorlie, but only one seminar was held, ie at Singleton in March 1997. Seminars at other locations were cancelled because of insufficient registrants. The presentation by Andrew Logan of BHP Cannington was not available for the Singleton forum. The aims of the forum were: ò to heighten awareness of the key technologies and their impact in the minerals industry in the medium term; ò to foster creative thinking; ò to encourage people to broaden their technical and commercial skills and develop individual networks and linkages based on an interest in these key technologies; ò to share information on the application of these technologies in the industry; ò to promote an enhanced appreciation of the need for an innovative culture; and ò to encourage staff to consider post graduate courses in technology management. The AusIMM wanted to not only raise awareness about `automation in mining' issues, but also to get technology in a more general sense back onto `centre stage'. The Forum was generously supported by CSIRO, Western Mining Corporation Ltd, BHP Coal Ltd, Aberfoyle Limited, Goldfields Ltd, Novacoal Australia Pty Ltd, Pasminco Ltd, and RGC Limited. The program was endorsed by the Centre for Mining Technology and Equipment (CMTE). Copies of the full papers are available from the authors, see `References'.

Jan 1, 1997

North Broken Hill Limited came into prominence as a producing mine at· the commencement of the present century, when a great many of the disabilities experienced in earlier mining operations th:rough lack of adequate stope filling had been overcome.The northern or narrower ore-body was first mined in the upper levels and, in the early stages, no great difficulty in mining was experienced. In depth, under the influence of its northerly pitch,. the wide southern ore-body entered the North mine between the 400 and 500-ft. levels. Owing to its flat dip and the relatively weak nature of the hanging wall and footwall, the value of close filling was recognized and this policy has been followed throughout the life of the mine. This feature undoubtedly contributed to the freedomfrom "creep" action to which some of the older mines had been subjected.The Broken Hill lead-zinc-silver ore-bodies occur as well defined replacements of favou:rable horizons, in intensely folded Pre-Cambrian sedimentaries. In the North mine two main replacement zones occur, the Gre being found where the beds are involved in a certain set of minor folds. The resulting ore-bodies are roughly elliptical in cross-section, the long axis of one being north-east of, and somewhat offset from the long axis of the other. The ore-bodies pitch eastwards at 40° and dip northwards at 60° in a fairly regularmanner. The southern Ore-body has an average length of 700 feet and an average width of 90 feet with a maximum width of 230 feet, whilst the nonhern ore-body on the lower levels averages 500 feet long and 40 feet wide.

Jan 1, 1940

COAL constitutes such a gigantic item in modern industry, either for direct heating, production of coke for smelting, or for the generation of power, that its quality and price play a very significant part in economic industrial progress. Australia is still a very young country industrially, and is groaning under many disabilities compared with competitors overseas, not the least of which is the quality of coal. Linked with the word "quality" should be that of "utility," for high-ash content prevents efficient utilization of the fuel.The marketing of good quality coal is a very important matter indeed, and if industry in Australia is to progress in the way that it should, this matter must receive keen attention.New South Wales, above all the other Australian States, has been blessed by nature with vast coal-fields, from which fuel is shipped to every State, and provides the base for power for most of our railroads and industries.Experts frequently refer to the fact that in some districts only partial extraction of thick seam coal is being made, without a care or thought for the future. Ranking next in importance to this is the fact that much of the coal is being carelessly marketed.Very few collieries in Australia are equipped with coal-washing plants for dealing more particularly with small coal grading which most industries require, and to which coal producers as a whole pay the least attention. In England each year nearly20,000,000 tons of coal is being water-washed before sale, and is marketed as a fuel of far greater utility once it has been freed from extraneous ash.Investigation proves that a great many pits in New South Wales are marketing coal (more particularly small coal) containing a considerable quantity of extraneous ash, due to the admixture...

Jan 1, 1926

By P Waters, S Miller

BHPBilliton operates the Mt Whaleback Mine located in the semi-arid Pilbara Region of Western Australia. Approximately 200 Mt of net acid generating (NAG) material still remains to be mined. Acid Rock Drainage (ARD) was first identified at the site in 1995 following cyclonic storms. This resulted in the development of strategies that have allowed the mine to successfully manage ARD whilst continuing to operate. BHPBilliton Iron Ore is working toward prevention of ARD in its operations, however, historical practices have left residual areas that must be considered. Three significant sources of ARD have been identified that must be managed: stormwater run-off from exposed pyritic shales in pit surfaces; basal flows beneath overburden storage areas following rainfall events; and contaminated water from pit dewatering. The mine contains all ARD water onsite. This is achieved by: storage of all affected water in the ARD dam; evaporation of affected water from the ARD dam and the adjacent evaporation ponds; pumping from upstream dams to prevent stormwater from being affected; and emergency storage and treatment in-pit as a contingency. The site ARD management strategy is approved by senior management and endorsed by State Government regulatory authorities and relevant external stakeholders. Additional strategies are also under evaluation to effect long-term closure of the operation. Record rainfalls from 1998 - 2001 have tested the capabilities of the ARD strategy and management plan. Learnings from these events, coupled with recommendations from an extensive technical audit in 2000, have been incorporated into the strategy for ARD management. This paper presents the strategy and an overview of the ARD management plan that can be considered and applied by other affected sites in the management of ARD.

Jan 1, 2003

The Olympic Dam deposit is located some 600 km north of Adelaide in South Australia. It was discovered in 1975 by Western Mining Corporation and in 1979 a joint venture was formed with British Petroleum for the evaluation and development of the project. Studies were completed and construction started in 1986 with the plant being commissioned progressively between April and August of 1988. In 1993 Western Mining acquired BP's interest and are now owners of the whole deposit. The scale of the initial development was 1.5 Mtpa of ore for the production of 45 000 tpa of copper cathode, 900 tpa of uranium oxide and some gold and silver. Two expansion programs have occurred in 1992 and 1995 and current performance is at the rate of 3 Mtpa of ore for the production of 84 000 tpa of copper cathode, 1500 tpa of uranium oxide, 24 000 oz per year of confined gold and 380 000 oz per year of confined silver (Table 1). An aerial view of the plant is shown in Figure 1. The benefit of diversifying into the production of more than one product is undoubted and the flexibility of being able to produce variable quantities of copper and uranium also allows advantage to be taken of a change in market conditions.

Jan 1, 1996

Distal air-fall ashes are widespread deposits that may record volcanism many hundreds of kilometres from their source. They are characteristically thin, fine-grained and have a low preservation potential usually being either eroded, or reworked and incorporated in overlying sediments following deposition. The most likely sites of accumulation are deep sea, lake and swamp environments where low energy conditions favour preservation. Post-depositional alteration of predominantly glassy volcanic ash is commonly extensive hampering identification of such layers in the geological record. As a result air-fall tuffs are poorly represented in the rock record and furthermore are commonly misinterpreted. Southeast Queensland during the late Triassic hosted active silicic volcanism and a number of fault-controlled basins in which coal-bearing sediments were accumulating. Silicic volcanics of late Triassic age are represented by the Brisbane Tuff in the Brisbane city area, the Chillingham Volcanics to the south of Brisbane and extending into New South Wales, the North Arm and Mount Byron Volcanics to the north of Brisbane, the Aranbanga Beds exposed around Gayndah and the Agnes Waters and Muncon Volcanics which occur northwest of Bundaberg. Stephens (1986) interprets these Volcanics as the remnants of a major silicic igneous 'province which he likens to modern continental orogenic margins. The Ipswich, Tarong and Callide Basins of southeast Queensland all contain coal measure sequences of late Triassic age that accumulated in alluvial plain environments. A Dicroidium flora is common to all and palynol.ogical evidence indicates a late Triassic (Carnian) age (de Jersey, 1975; Stevens, 1981). The coal seams of the three basins are characterised by their thickness (up to 25 m) and the presence of abundant thin, laterally persistent, kaolinite claystones (tonsteins) that show a marked similarity of morphology, texture and mineralogy. Detailed studies of the Ipswich Coal Measures (Falkner, 1986) suggest a volcanic air-fall origin for the tonsteins of the Ipswich Basin. Similar.tonsteins from the Tarong and Callide Basins provide evidence for widespread silicic volcanism during the late Triassic in southeast Queensland.

Jan 1, 1987

By S Paciornik

The traditional trading of iron ores is based on chemical specifications and particle size distribution. However, recent characterisation studies, that bring additional information like mineralogical composition and microstructural (textural) aspects, have become important. They contribute to determination of the iron ores downstream beneficiation operations and subsequent steelmaking processing, allowing improvements on both new and existing processes. Despite progress in commercial scanning electron microscope/energy dispersive spectrometer (SEM/EDS) automatic instruments in the last decade, these systems are not capable of performing the identification and discrimination of major iron ore minerals (haematite and magnetite) and the consequent description of its microstructure. On the other hand, reflected light microscopy (RLM) can easily distinguish the iron oxides by their reflectancies, but it cannot discriminate quartz and epoxy resin, which present similar colour on images. The present work proposes an innovative method to perform a quantitative mineralogy characterisation of iron ore based on RLM-SEM co-site microscopy. This technique combines images obtained by RLM and SEM through an automatic registration procedure that accurately aligns the two kinds of images of each field. In fact, it creates multi-dimensional images, which are then analysed using image processing and pattern recognition techniques. The case study is an itabiritic iron ore from Quadrilßtero Ferrffero (Brazil) which contains mainly quartz, goethite, magnetite and haematite. The discrimination of phases that are not distinguishable with either RLM (epoxy resin and quartz) or SEM (haematite and magnetite) can be performed through this multimodal approach, allowing the subsequent mineralogical quantification. The mineralogical quantification computed by image analysis was consistent with independently obtained results based on the Rietveld technique.

Jan 1, 2008

By O V. Vasyukova

Formation of porphyry-style ore deposits starts with the metal extraction from magmas at so-called magmatic-hydrothermal transition (MHT). The processes and compositions at MHT are difficult to study as the record of them is poorly preserved. As the MHT is characterised by massive crystallisation of quartz, including quartz æeyesÆ and veins, their study can elucidate questions related to metal transport and deposition. Quartz grains from the porphyry deposits all over the world (Antapaccay, Peru; Batu Hijao, Indonesia; Climax, USA; Panguna, PNG; Far Southeast porphyry, Philippines; Rio Blanco, Chile; Omsukchan, Russia) were studied by optical, SEM-CL and BSE microscopy, electron microprobe and LA ICPMS. Quartz grains, even within each sample, have different shapes (rounded, egg-shaped, amoeboid or euhedral) and cathodoluminesence (CL) patterns (shape, number and width of bands in CL images). The outer layers of quartz are markedly different, which is unexpected if the grains had formed in the same conditions. Inflections and blurring of CL bands are often structurally associated with fractures that are commonly healed with secondary quartz and associated fluid inclusions. Our results show that quartz æeyesÆ could not crystallise from a silicate melt as normal phenocrysts. It is likely that in situ segregation of residual SiO2- and H2O-rich liquid and its solidification followed by coagulation (eg formation of silica-gel globules) took place in the magma (crystal mush) during MHT. Such globules could remain in a plastic state for a long time even at rather low temperatures. The solidification of globules occurred after bands of different composition had formed and led to fracturing of solidified and inflection of unconsolidated layers. All fluids (liquid and vapour) released from the original silicagel during solidification were trapped as inclusions (aqueous, salt-rich and sulfide). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Application of Agitated Leaching for Iron Removal from Silica Using Sulfuric and Hydrochloric Acid In this research, iron removal from silica used in glass industry was investigated using agitated leaching method. Silica sample was provided from silica concentrate originating from Chalchoog Silica Mine located in Abhar, Iran. The sample contained silica, iron oxides and clay minerals. For characterization of samples XRD and XRF analysis and atomic absorption method were applied. Silica and iron oxide (Fe2O3) grade of head sample was 98.41 per cent and 0.067 per cent respectively. Two inorganic acids (sulfuric and hydrochloric acid) were used in agitated leaching tests. Two series of L9 orthogonal array of Taguchi design with replication were used to determine the effect of parameters including acid dosage, leaching duration, ambient temperature and solid content on iron removal. The statistical calculations and analysis of variance (ANOVA) were carried out by means of DX7.0, Minitab14.0 and Winrobust1.02 softwares and also statistical calculations were checked manually using Excel software. Also multivariate regression was applied in order to forecast Fe2O3 conent of final product. The optimum conditions for leaching tests which sulfuric acid was employed are as follows: 40 minutes leaching time, temperature of 85¦C, 40 g/L acid concentration and solid content of 20 per cent. Under this condition the amount of iron oxide in silica was decreased to 0.042 per cent. The optimum conditions for leaching tests which hydrochloric acid was employed are as follows: 80 minutes leaching time, temperature of 75¦C, 30 g/L acid concentration and solid content of 20 per cent. Under this condition the amount of iron oxide in silica was decreased to 0.035 per cent.

Sep 13, 2010

Mispah form (FAO: Lithosol) soil contaminated with >380 000 mg kg-1 creosote was co-composted with sewage sludge and poultry manure for a period of 19 months. The soil was mixed in a ratio of 1:1 (v/v) with wood chips to improve aeration. The soil-wood chips mixture was then mixed in a ratio of four soil-wood chips mixture: one compost material (sewage sludge or poultry manure). Compost heaps were set up in triplicate on wood palettes overlaid with double layers of nylon straw bags. Control experiments, which contained the contaminated soil-wood chips mixture without sewage sludge or poultry manure were set up in triplicate. Moisture, temperature, pH, ash content, C:N ratio of the compost and the creosote concentration of the soil was monitored monthly. The concentration of selected creosote components in the soil was also determined at the end of the incubation period. Temperature was observed to rise to about 60¦C in the poultry manure and about 58¦C in the sewage sludge within two months of incubation, while temperature in the control fluctuated between 15¦C and 35¦C throughout the incubation period. Creosote concentration in the control was reduced by 17 per cent at the end of the incubation period while concentration of creosote in the sewage sludge and poultry manure compost was reduced by about 99 per cent. The percentage rate of creosote reduction in the poultry manure compost was initially lower than observed in the sewage sludge compost. However, the reduction rate became similar towards the end of the treatment period. The concentrations of selected creosote components were reduced by about 100 per cent within the same period. Respiration of compost microorganisms and counts of microbial populations showed that microbial activity correlated with reduction in creosote concentration.

Jan 1, 2004

Water is becoming an increasingly valuable commodity in Australia and the mining community is finding itself competing with pastoralists, domestic consumers and industry for access to what is an essential but finite resource. This paper will provide an overview of various legislative regimes in Australia governing water resources, and will review some of the fundamental issues which should be considered by mining companies when contracting with other parties for the supply of water. The paper will focus on mechanisms to secure access to water for mining purposes, and will deal with the following issues: Grants of water entitlements under legislation û (navigating the legislative requirements necessary to facilitate the taking and use of water for mining activities) The paper will focus on the key legislative requirements for securing access to water in Queensland, Western Australia, New South Wales, Victoria, South Australia, Tasmania and the Northern Territory, and will examine: compliance with regulatory processes for securing water entitlements through the grant of water allocations, licences and permits, etc; and dealings with water entitlements (ie statutory mechanisms for transferring water entitlements on a temporary or permanent basis). Securing access to water under water entitlements through contractual means. The paper will also review of some of the fundamental issues which should be considered by mining companies when contracting with holders of water entitlements for the supply of water from both groundwater and surface water sources. These issues include (inter alia): securing appropriate rights to take and use water in compliance with relevant legislation, the necessity to protect the validity of underlying water entitlements, ensuring the security of supply for the contract term, access rights affecting water entitlements and other important issues relating to the security of water entitlements for miners.

Jan 1, 2003

Builders have been very familiar with iron since ancient times, but because of its weathering characteristics it was relegated to use as a fastening material in unexposed places and bronze became the popular metal for exposed applications. It is of interest that iron nails buried deeply about A.D. 87 at a Roman fortress and carefully covered with clean beaten earth under conditions practically excluding oxygen were found to be almost unrusted 1870 years later. (1) Today, weathering steels, which contain less than 2% of alloying additions, can be used in exposed situations without protection and without experiencing continuous wastage. As we all know the steady access of atmospheric oxygen to the surface of plain steel causes continuous corrosion. Weathering steels, on the other hand, due to their alloying additions develop their own impervious surface layer which limits the access of atmospheric oxygen and effectively limits corrosion. Table 1 shows the chemical composition of a plain carbon steel and a typical weathering steel. Fig. 1 shows what we refer to as direct corrosion - time curves in which corrosion loss is plotted against time of exposure in an strial environment. The weathering steel has a high rate initially which then decreases steadily for about three years, as the stable rust film builds up. This is followed by a practically linear relation where the very low corrosion rate, according to one school (2), is due to a blocking of the rust pores by insoluble complex salts formed from interaction of the oxidation products of the separate alloying elements. The start of the linear region represents a total corrosion loss of only about 2 thousandths of an inch.

Jan 1, 1970

By J Tuma

Technical measurements are an integral part of research and development of new technical devices. Now they are also an integral part of production too, especially as a part of quality control systems. More new problems started with they applications up, like storing and following preservation of big data files. Many problems are also with processing of the measurement results, especially to be up to standards of ISO 9000 normative. It includes basic data about the measurement (structured data) and measurement outputs (huge data streams). Using database systems looks as good idea, because of structured measurement data and they processing. They were developed more concepts of database measurement system support during the research project MSM 272300012. It was decided to develop specialised measurement systems, on the base of experiments and experiences with they use in operating conditions. It proved to be wrong to develop general system, because of compound operating and long response of the system. And it is not possible to use these systems for mass production systems. The problem of data storing is not as easy to be answered, because of dependence on used technical devices. During realisation the measurement system for gearbox noise measurement are data stored to the database, because used analyser system PULSE (Brnel and Kjµr Co) is open structure and can cooperate with other software systems. Anyhow the data streams are not longer (after compression) than the Memo data type, in practical use increases the data file too fast (about hundreds MB daily). Therefore we must include a special supervisory system for administration and creating data files to the system. Nevertheless the used system MS-Access supports data files up to 1 GB, for practical application is better if the file size do not exceed the capacity of CD-ROM disc.

Jan 1, 2003