Search Documents

By J-H Shin, Y-S Jung, D-J Youn, G-J Bae

This research is to grope for a method to reduce high pore pressure taking place on tunnel shotcrete lining, especially in underwater tunnels, effectively by utilising a new concept of patternised pin drain. Accordingly, the patternised pin drain system is investigated numerically in order to confirm to the effect of reduction of pore pressure by the pin drain and its effective application. Installation of pin drain shows considerable reduction in the figure of pore pressure. It is found through 2D numerical modelling that the change of pore pressure, according to the shape and the location of pin drain, is sensitive by the sequences of the change of location > the change of length > the change of angle degree. In the results of investigation in 3D modelling, the pore pressure is the largest in the centre of the interval among pin drains, and it is possible to obtain an ideal degree of longitudinal angle and an interval by investigating pore pressure taking place on the lining.

Jan 1, 2008

By V Lickfold, A J. Crawford, A J. Wilson

A total of 12 alkalic porphyry centres of Late Ordovician age have been discovered in two mineral districts within NSW. The alkalic porphyry deposits are hosted within shoshonitic volcanic centres that formed where a major cross-arc basement structure (the Lachlan Transverse Zone) cut the Ordovician Macquarie Arc. The Macquarie Arc was amalgamated with the back-arc basin sediments of the Wagga Marginal Basin and with the proto-Pacific margin of Gondwanaland to form the Lachlan Fold Belt after the cessation of arc magmatism in the Late Ordovician. Within the Ordovician volcanic belts of NSW, the alkalic porphyries are the most significant mineral deposits economically. The combined resource of the Cadia district porphyries (729 Mt @ 0.79 g/t Au and 0.30 per cent Cu) makes Cadia the worldÆs seventh largest known porphyry gold system and the largest known gold resource in an alkalic porphyry system (574 t Au). Hydrothermal alteration in the alkalic porphyries comprises a complex sequence of potassic, calc-potassic, sodic, calc-sodic, propylitic and late-stage, typically fault-controlled phyllic assemblages. Hematite dusting is common in many of these alteration assemblages, giving the intrusions and the altered volcano-sedimentary host sequences a distinctive pink-orange colouration. Intensely developed hydrothermal alteration assemblages are localised to within a few hundred metres of the composite intrusions that sourced the mineralising fluids, making these deposits difficult exploration targets. Sulfides are typically zoned, with several of the deposits having bornite-rich cores, chalcopyrite-dominant annuluses and pyritic outer haloes. Gold is well correlated with bornite in most of the deposits, and with chalcopyrite at Cadia Hill.

Jan 1, 2002

I offer some comments which might complement the valuable recent paper by De Angelis et al (1987), on the newly discovered nickel-copper deposit at Radio Hill.The authors have accepted subdivisions and correlations by Hickman (1977, 1983) although they are disputed (Fitton, Horwitz and Sylvester, 1975; Horwitz, 1979; Horwitz and Guj, 1986).Also, in my opinion, more plausible correlations of the Sholl Belt with Whim Creek Belt have been shown, but not discussed, in Hudson and Horwitz (1986, Figure 1). Our suggested correlations and subdivisions have appeared in publications and reports which are not readily available, but it is gratifying to note that many of the observations and conclusions of De Angelis et al are consistent with our conclusions of the Whim Creek Belt.The units of the Sholl Belt (of Hickman, 1983), between the Sholl Fault (Shear Zone) and the overlying Mt Bruce Supergroup to the south, equate well with units of the Whim Creek Belt. A basalt, characterised by an abundance of vesicles and similar in many ways to the Wararnbi Basalt of Fitton, Horwitz and Sylvester (I975), is well developed at the base of the succession, particularly in the southern part of the area (Figure 1). It is overlain by acid tuffs (locally metamorphosed, such as at Whundoo Mine) and associated acid and mafic lavas, similar to those of the Mons Cupri area. The mafics in the succession are marked by the absence of the numerous cherty sedimentary intercalations, such as the Marble Bar Chert, which occur in the Warrawoona Group; and they also lack the intense chertification that is prevalent in all parts of the proven areas of Warrawoona Group rocks.The Whim Creek Group is overlain, locally unconformably (two to three km east of Mount Negri), by the Negri Volcanics which include here the Louden Volcanics (unit Abu of Hickman, 1977), (Horwitz, 1979). The negri volcanics are an alternating sequence of variolitic and quench textured lavas not dissimilar to the highest units of the Sholl Belt (Figure 1). They range from high-Mg basalt to tholeitic andesites (Glikson et al, 1986, pp 79 and 84). The whole succession of the Sholl Belt is estimated to be of the order of four km in thickness, more consistent with the two km thick (Horwitz, 1979, Figure 1) Whim Creek area sequence than with the much thicker Warrawoona Group sequences. The Whim Creek Group (including the Negri Volcanics) is considered to be a widespread grouping (Fitton, Horwitz and Sylvester, 1976; Horwitz, 1979; Horwitz and Guj, 1986) which is prevalent in the northern part of the Pilbara Craton. It is considered by these authors to include the Mallina Formation turbidites of the trough area of Ryan (1965). One component, the Mons Cupri Volcanic, is about 2.95 Ga (Richards and Blockley, 1984). Between the Sholl Fault and Egina, the Whim Creek Group is intruded by large ultrarnafic to granophyric ills of the Millindinna Complex (Fitton, Horwitz and Sylvester, 1975), dated at 2.860 ± 002 Ga by Gulson and Korsh (1983) near the Sherlock River (south side of Caines Well Granite area). The Millindinna Complex has been equated to the same magmatic episode as the layered complexes of the Sholl Belt by Fitton, Horwitz and Sylvester (1975, p 20).

Jan 1, 1988

The Mount Lyell Company's concentrating mill is situated about a quarter of a mile westward of the portal of the North Lyell tunnel, which serves the North Lyell, Royal Tharsis and Crown Lyell mines, being on the 1100-ft. level of the first named. The Comstock mine is connected with the tram system at this level by five and a half miles of steam tramway, two-foot gauge being standard throughout.The plant is well placed with regard to all essential services and has an excellent water-supply from a series of three dams on the West Queen river.MILLING ORESThe mill feed is a mixture of the outputs from the foUr mines mentioned, each of which has its characteristic ore, but, generally speaking, about half of the ore consists of siliceous schists and the other half of hard grey quartzite. The schisty ores are easy to crush, but, on grinding, while the schist slimes readily, the quartz granules are hard, resulting in the handling of heavy loads on the secondary classifiers. The quartzite ores are both hard to crush and difficultto grind.The principal sulphide materials are bornite, chalcopyrite, and pyrite, chalcopyrite being the main copper-bearing mineral.The crystallization is coarse in the schisty ores, but it has been shown that even the 200 mesh (Tyler) material contains included sulphide particles. At the present time the sizing of the final tailing averages 80% through 200 mesh.

Jan 1, 1932

By J R. Kyle

The Deep Mill Level Zone (DMLZ) skarn Cu-Au deposit is the deepest explored part of the Ertsberg East Skarn System extending from the surface at 4200 m elevation to the DMLZ at 2900 to 2600 m. The DMLZ is hosted in an upper Cretaceous to lower Tertiary siliciclastic and carbonate succession adjacent to the 3 Ma Ertsberg pluton. Much of the DMLZ ore is hosted by mixed assemblages of siliciclastic and dolomitised carbonate strata that have been altered to Mg-rich skarn assemblages. Unaltered equivalent strata from a 300 m cored interval in the Yellow Valley Syncline were characterised petrographically and representative samples were analysed for major element compositions. These stratigraphic and chemical units are interpreted to be responsible for the varying skarn lithologies within the DMLZ. The dominant prograde skarn assemblages are controlled by protolith composition, notably the relative abundance of quartz, dolomite, and calcite within the protolith. Models based on isochemical metamorphism of mixed assemblages of quartz and dolomite suggest that the formation of the forsterite-diopside dominant skarn assemblages resulted in the greatest amount of pore space increase. DMLZ Cu-Au concentrations were locally controlled by host lithology, with structural features providing fluid pathways that focused the mineralising fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Mt Muro was a gold and silver mine in Central Kalimantan on the Island of Borneo, Indonesia. Aurora Gold through its Indonesian subsidiary Indo Muro Kencana owned the project. Processing commenced in November 1994, and ceased in June 2002. Mining, including prestripping, commenced in March 1994, and ceased in May 2002. Nominal throughput was 1.5 Mtpa, at average grades of 3.80 g/t Au and 99 g/t Ag. From the start of prestripping until the end of 1996, Drill Blast sampling was the main grade control method. After several studies into the viability of Reverse Circulation, including an assessment of costs and benefits, the switch from Drill Blast to Reverse Circulation was made in late-1996. From 1997 until the end of the project Reverse Circulation was the main grade control method. The mine-to-mill call factors û the reconciliation between predicted and actual tonnes and grades delivered to the mill û for the period from commencement of processing to December 1996 were 1.069 for tonnes, 0.949 for gold, and 0.969 for silver. The mine-to-mill call factors between January 1997 and June 2002 (excluding a period of significant illegal mining) are 1.086 for tonnes, 0.977 for gold and 1.025 for silver. At face value this indicates a 2.8 per cent absolute improvement for gold, and 5.6 per cent for silver. Using average grades for the project, an additional 5112 oz of gold, and 267 173 oz of silver were delivered annually to the mill using Reverse Circulation sampling instead of Drill Blast sampling. The additional recovered metal value is estimated at $US 2.87 M annually, significantly exceeding the cost of Reverse Circulation drilling. This paper discusses a number of issues that may affect the estimated benefits.

Jan 1, 2003

By P SSrkkS

Mining is commonly seen as a typical basic industry with rough and even dangerous working conditions, heavy environmental load, and a low level of high-technology and automation with much manual work and operations. A mining operation (open pit or underground) is a very complex one consisting of many manual, physical, mechanical and logistical operations with different human interfaces and decisions. For this reason it is a demanding and potential area for all applications of automation and information technology: controlling difficult non-linear, time varying multivariable processes and machines; solving of ergonomic safety and environmental problems; automation of logistical systems; applying robotics, mechatronics, and information handling, etc. In addition to that, big economic sums are involved with these operations. On the other hand, automation technology has developed towards intelligent and adaptive systems including some from the above mentioned fields of automation. Connecting them with modern information and communication technologies makes the idea of an intelligent and unmanned mine more and more feasible in the near future. This requires intensive co-operation and co-ordination between the mining industry and manufacturers of mining machinery. This has been successfully accomplished in the five-year Intelligent Mine research and development program as well as the three years of subsequent implementation of its results in Finland. The basic elements of an Intelligent MineTM concept are:mine-wide information and data acquisition system; high-speed two-directional mine-wide communication network for real-time monitoring and control; computerised information management, mine planning, control and maintenance systems; automated and tele-operated machinery and equipment which are connected to the information system; and links to the public information networks. The degree of automation of an intelligent mine depends on many technical and economical factors. The basic precondition for such an approach is that it will improve the total economy of the mine. This paper will describe the Intelligent Mine Technology Program with the results. Also the implementation which took place during starting of a new underground mine (Outokumpu Chrome Oy Kemi Mine) will be described.

Jan 1, 2000

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

Stringent environmental benchmarks imposed by governments and successful legal challenges in the country of origin have changed the risk profile for all mining companies over recent years. In developing countries, however, where high government standards may not always be in place, direct community action has often made worthless substantial investments in otherwise viable mining operations. Real limitations are therefore imposed from these risks on all areas of mining activity, wherever they may be. Thus, the bar has been raised for all companies developing or operating mines. This paper argues real financial and global industry reputation benefits accrue when all known environmental risks, where practical, are managed. In response, among major international mining companies, as the industry moves towards greater global consolidation, senior management teams have increasingly adopted corporate governance standards including æTriple Bottom LineÆ (shareholder/government/community) sustainability reporting. Sustainability reporting is encouraged by improved international stockholder and financial investor perceptions by contributing to lowered social, community and geopolitical risk which lowers the cost of access to funds as well as improving staff morale and productivity. New mines must not only be primarily financially viable but must operate throughout in a sustainable way. Case studies of some recent mining operations, who have not foreseen or proactively managed major environmental risks, demonstrate the dire financial and personal implications for managers, directors and shareholders from not identifying and managing these environmental risks. Merely having a corporate policy statement on environmental standards or high level Government approvals process for a mining activity does not preclude mining operations from the risk of direct action by local populations or future adverse legal implications from risks which were perhaps identified but not mitigated effectively. Methods and processes for the identification and active management of environmental risks in the global arena are discussed to add a practical element to sustainability, based on the authors recent strategy development processes with governments and major mining houses such as BHPBillition, Rio and Xstrata. Emphasis is placed on proactive, innovative yet practical solutions which, where possible, show positive contributions firstly to the financial bottom line but also the community at large.

Jan 1, 2003

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

By Sneddon J

This Is not a highly technical paper, but rather an attempt to give a general outline of coal mining for the benefit of those present who may have little or no experience in the industry, and is intended to give some general knowledge which may help to a better understanding of the problems of the industry. A knowledge of the disposition of workable material is necessary to give a comparison with other mining practices. Coal Is usually found in comparatively fiat seams of varying thickness, whereas other minerals are generally found in highly inclined lodes of variable width. However, even in comparatively flat seams unaffected by faulting, grades can, and do, vary greatly over short distances.This variation causes many local problems in working the small area affected. Even very steep seams, and some are much steeper than 1 in 1, vary considerably not only in grade, but also in direction of grade and level course. This is probably caused by folding during alteration of the shape and form of the basins after deposition.These swellies are common to most coal seams and vary only in extent. This type of variation in grade and direction of grade, while common to most ore bodies, is a matter of great importance in coal mining when it is considered that roadways are driven in the seam itself and have to be graded and made suitable for haulage purposes.The area of ground involved in an individual coal mining operation is often very large; many times larger than most metal mining propositions, and often comprises many thousands of acres.When it is considered that the specific gravity of coal may be only one-fifth of that of some ores mined, and the coal seam may be five or six feet in thickness, the vastness of the area necessary for continuous mining operations over many years will be realised.To achieve comparable outputs, with about five times the bulk of material to handle, much more ground and working places must...

Jan 1, 1947

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

Jan 1, 2004

By Blom W. M

Shareholders, creditors, government agencies and auditors all have a different perspective of financial reports which is determined by the uses to which they put the information disclosed in the report.Shareholders today are better informed than previously and are more aware of the market in which they are investing. This is the result of the increasing role of institutional investors and the increasing reliance being placed on analysts to interpret financial information.

Jan 1, 1990

Carbothermal Reduction of Ilmenite Concentrates and Synthetic Rutile in Different Gas Atmospheres

Sep 13, 2010

By C Fenton

The mining industry is a relatively minor user of water, which has historically been largely soured from private schemes. Frequently mines are often located in areas with limited available water resources. Water reform is increasingly affecting access to water for new mining projects and mining companies are being required to consider the value of water and the implications of reliability in their planning. This paper seeks to briefly review the water reform process in Australia and how it is affecting the mining industry with reference to some recent project experience.

Jan 1, 2003

Oxidation or sulphidization of the surface of pyrrhotIte partIcles enhances atomic interdiffusion at elevated temperatures and provides a mechanism for interface growth between particles in contact. In a mass of pyrrhotite-rich ore or tailing, where oxidation heating is not controlled, bonding of particles by diffusional mass transport contributes significantly to the agglomeration of the mass.

Jan 1, 1976

While international coal trading operations often involve relatively small contract quantities, delivered over short periods or even in single shipments, most coal is supplied under long term arrangements. In entering into these arrangements the customer needs to be assured that coal of suitable and consistent quality can be supplied for their duration in the volume required. A detailed knowledge of the mine and transport system is required and must be presented from the customer's perspective.

Jan 1, 1983

This paper provides an overview of current and future mine developments in the major island nations Indonesia, Papua New Guinea (PNG), New Zealand, and Fiji, and the French territory of New Caledonia. Many of the other 11 small island nations in the region, such as Vanuatu, Pulau and the Solomons have been the subject of considerable exploration orientated towards gold in the past few years but without any deposit found with confirmed economic viability.

Jan 1, 1990

By Tooth MA

Mining, metallurgical and engineering consultants have made a considerable contribution to mining industry development in Australia. Expertise has been developed locally to a high level during the last decade which has contributed to the success of many recent mining projects. The services available'cover the whole spectrum from the evaluation of ore reserves, through feasibility study and financial evaluation to design, project management and commissioning. Using these services effectively and economically is an objective which client and consultant both must pursue but which is not always achieved. This paper discusses some aspects of the use of consultants which the experience of the authors has shown to be of prime Importance

Jan 1, 1975