Search Documents

By Kerr M. H, Slaughter P. J

Design of the new cemented hydraulic fill plant was based mainly on experience with a succession of previous fill plants. Two stage cycloning of combined concentrator tailings was introduced. Design of the two stage cyclone configuration was assisted by computer simulation of cyclone performance. Cementing additives, namely Portland cement and ground copper reverberatory furnace slag, drawn from bulk storage, are pre-slurried prior to mixing with hydraulic fill. Quality control of fill being sent under- ground is achieved by a series of automatic control loops. Plant instrumentation was given prime consideration during the design phase. Inventory checks of all mass flow metering equipment are made at regular intervals. Fill is pumped to boreholes at several locations. Details of the equipment and operating procedures for the plant are Discussed.

Jan 1, 1973

THE auriferous sulphide ores of the eastern end of Gippsland, and notably of the Cassilis and lVIitta districts, are amongst the most complex and refractory in Victoria-perhaps in Australia. The minerals occurring in these ores are pyrite, arseno-pyrite, zincblende, galena, and (in smaller amounts) some of the copper, sulphides, as chalcopyrite and covellite; and some of the antimonial minerals, notably stibnite and jamiesonite. In the oxidized portions of the lodes, the oxidized lead and iron minerals, and small amounts of the hydrated arseriiate of iron, are found.In the Cassilis mine, near Omeo, copper is present usually in quantities of under 1 %. The magnetic sulphide of iron is of fairly common occurrence. In, the upper levels of the Cassilis mine tin was usually present, the amount going up to 3% in some samples of concentrates. These minerals occur sometimes banded, but usually as an intimate mixture-pyrite and arseno-pyrite predominating. The gangue is usually quartz (blackened by enclosed particles of sulphides). Calcite, magnesium silicate and felspar are also present in varying amounts.

Jan 1, 1911

By S Tavelli

This discussion will present a case study in developing solutions to a metropolitan quarryÆs public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over four months duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterisation, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

The relevance of borehole and bore core evaluation to the design of underground coal mines is illustrated by considering the technical parameters of colliery design and the information from which they are constructed. The nature of this information is described, together with some methods for its storage, processing and presentation. Geophysical exploration techniques are compared as information sources. It is concluded that borehole and bore core evaluation is relevant and necessary for colliery design, but that optimum results will be obtained if drilling can be combined with geophysical techniques. Because of the inherent uncertainties in prediction of mining conditions the necessity of obtaining as much information as practicable from drilling evaluation is also stressed.

Jan 1, 1977

Over the last decade mineral exploration in New South Wales has increased markedly. This is due to various factors including the influx of overseas companies an. capital, increase and stabilization of metal prices and improvements in exploration techniques. The initiation of full-scale petroleum exploration and recent discoveries of large mineral deposits in the west, north-west and north of Australia has increased overseas capital, and brought scientists and technicians into the country. Naturally there has been an overflow into New South Wales, which is less attractive as an area for new and large-scale discoveries. In some fields, rise in metal prices and price stabilization has largely contributed to the intensif- ication of exploration. Increased tin production in New South Wales since 1963 is a direct result of price rise and stabilization, and rise in the price of silver has revived an interest in silver prospecting in recent Years,

Jan 1, 1969

By P Trotta

The paper provides a structured methodology to investigate metallurgical problems within the operating concentrators. The strategy uses classical metallurgical data analysis as well as pulp, solution and surface analysis to determine the reasons for particular behaviours. The approach applies equally to all mineral-processing operations. To demonstrate its effectiveness a case study, based on work conducted at Pasminco Rosebery Mine, is described. In this work, the classical metallurgical analysis indicated that a significant amount of sphalerite reporting to the lead concentrate occurred as liberated particles. A combination of pulp, solution and surface analysis supported the hypothesis that the liberated sphalerite was recovered by inadvertent activation by lead ions. Laboratory studies have indicated that the use of sodium carbonate, by itself and in combination with zinc sulphate and sodium cyanide, when added to the lead regrinding mill can depress sphalerite flotation, resulting in an improvement in the lead grade/recovery curve. When this approach was tested in the plant other more dominant issues masked any positive effect the addition of sodium carbonate may have had. The plant trial highlighted the real need for additional regrinding capacity.

Jan 1, 2002

By Watson D. F

Armstrong's (1983) criticisms of PhiIip and Watson's (1982b) note on optimal drilling patterns are based on misinterpretation, supported by errors in geometry. Furthermore, Armstrong argues conceptually from the perspective of Matheronian geostatistics, as does also Rudenno (1983a, b). Thus, both authors embrace a global, probabiIistic method of assessing spatial data sets, an approach that must be contrasted strongly with local, deterministic interpolation methods. Some of the important assumptions of geostatistics are outlined and the non-unique nature of the method discussed. A probabilistic approach can be judged appropriate when exploration data are erratic, or known to be unreliable, or when extrapolation is desired. Where data are treated as exact, kriging can give the most biased result if tested against other interpolation methods. We reiterate our previous conclusion that the equilateral triangular grid is approximately 30 per cent more efficient (in terms of numbers of drill holes) compared with a square grid for the same maximum interpolation distance. This is simply due to the improved isotropy of sampling. New, locally-based, deterministic methods for computing ore reserves seem to be required.

Jan 1, 1984

A considerable debate has arisen regarding the best route for the beneficiation of iron ore. Supporters of jigging technology claim that although the technology is old, due to recent advances in jig control and a better understanding of the separation processes within jigs, it offers significant advantages over dense medium separation, especially in terms of reduced capital and operating costs and simplicity of design. Supporters of dense medium separation claim that this technology is proven to provide the best possible separation and that the gain in efficiency over the life of the plant, compared to that of a jig, will more than offset any differences in capital or operating costs. The truth is that both viewpoints are valid and that the choice is ultimately determined by specific characteristics of the ore being treated. Factors that need to be taken into account in deciding upon the correct option include the size/density distribution of the ore to be treated, the different size fractions which must be treated (lumpy or fines), differences in yield at grade, plant layout and capital and operating costs. Each of these factors will be discussed in detail and a case study for both lumpy and fines will be presented.

Jan 1, 2007

By Robinson BW, Walker RK

Using a new highly stable automated electron microprobe analyser, detection limits for gold in arsenopyrite have been improved. Using the AuLA emission tine at 40kV and 500nA, a limit of approximately 10gpt is attained in 10- lSmins. Some unusual features of the background need to be taken into account. Several ores containing different levels of gold in arsenopyrite have been examined, and it has been shown that gold is not evenly distributed between grains (some may contain more than 1%, invisible optically), and that the grains containing gold are often zoned. Gold may be released from the arsenopy rite by weathering or by heating in an inert or slightly oxidising atmosphere.

Jan 1, 1989

Synthetic and commercial activated carbons are characterised for several chemical and physical properties. A range of techniques is used to establish correlations between physicochemical parameters and gold- adsorption activities. The most important parameter in the carbon activation process for a product with a high gold-adsorption activity is the activation temperature. High activation temperatures yield products with large micropore volumes which provides sites that are ideal in size for adsorption. The surface area of an activated carbon is not necessarily a good measure of its adsorption activity. Surface oxygen-containing functional groups are identified by Fourier transform infrared spectrophotometry to be comprised mainly of ethers and hydroxyls. These functional groups line the edges of the micropores imparting a polar character to the pore and aid in the solvation of the adsorbate. Oxidants such as nitric acid result in a proliferation of surface carboxyl groups. resulting in a negatively- charged surface that is not conducive to the adsorption of gold.

Jan 1, 1993

By Smitham J. B

A selection of Australian washed coal samples was examined to determine the effect of sample hydrophobicity (rank) and particle size on froth stability in the flotation process. The results indicate distinct rank-based variations in froth volume and stability for flotation tests conducted without the use of collector, over a series of particle size distributions.High-rank coals showed a greater tendency to generate stable, high-volume froths than coals of lower rank. Implications for circuit design and operation are outlined.

Jan 1, 1988

By Misra A

The development of roadways in underground mines in Autralia is by conventional continuous miner technology. The rate of development achieved using this technology is improved by modifications to this technology using additional equipment such as surge cars or decreasing roof bolting time.Development rates achieved with this technology compare with developing technologies such as high capacity continuous miners, continuous transportation and simultaneous cutting and bolting systems such as the Kemcol Beaver. Pillar dimensions have an effect on the rate of development.'

Jan 1, 1991

This paper examines the interplay between longwall support design/geometry features, operational controls and geological features on ground response. Experience from several investigations is used to demonstrate the influence of factors such as longwall support capacity and geometry, setting pressure, coal seam strength and stiffness, tip-to-face distance and hydraulic supply and control system parameters on longwall ground response. These factors are then used to outline the requirements on key controls such as retreat rate and cutting height and their influence on allowable roof convergence. The ground response curve concept as a means to provide graphical representation of longwall support and strata interaction processes is presented. The approach was developed to address the requirement for a practical longwall support evaluation and selection tool that can take account of support load influences such as changes in roof geology or cover depth. An example of the comparison between single pass longwall and top coal caving in a thick seam environment is given to demonstrate the influence of the various factors discussed.

Jan 1, 2005

This paper summarises some observations regarding the way SAG and AG mills work based on the last ten years of pilot plant operation, grinding circuit design and operational reviews for various projects in Australia and overseas. The main purpose is to promote discussion on key factors influencing breakage in a SAG mill. The focus of the paper is on two questions: How do mill lifters and liners really work and have an effect on grinding? How does the mill charge composition impact on grinding performance? The focus of the paper is on observations of mill behaviour in both pilot plant trials and plant operation, particularly on Cadia ore. DEM, by others, and JKSimMet modelling of SAG mill performance have greatly assisted in forming the ideas expressed in the paper and both are valuable tools in developing our understanding of the comminution process. Put in the æextremeÆ form the major observations and conclusions expressed in this paper are that: the main purpose of mill lifters is to reduce mill liner wear and not to promote rock breakage; the often promoted theory that balls impacting the ætoe of the chargeÆ is a dominant form of breakage is incorrect; and fines production in a SAG mill is primarily a function of the rock load mass, with a secondary dependence on ball load for any given circuit configuration.

Jan 1, 2007

By E M. Rykaart

The design of soil covers as part of the remediation initiatives for mine waste facilities is common practice and more and more engineers are faced with designing these facilities. The design issues associated with these soil covers are complex and requires a good understanding of unsaturated flow. More engineers are making use of numerical models to predict how cover designs would perform, and this has been necessitated by the high non-linearity associated with solving unsaturated flow problems. There are numerous numerical models available to the prospective users and they are all simplifications of reality using different assumptions. The users of these models often do not understand the limitations of the models but rather select a model based on ease of use, and that lends to increasingly erroneous designs being proposed for construction. This paper describes a comparative evaluation of a cover design using four different codes available today; SoilCover, SWIM, HYDRUS-2D and HELP. The paper does not propose to measure these codes up against each other and make statements about which is better than the other but rather illustrates how the assumptions in each code affect the outcome. The data set used for the comparative study is a well calibrated data set that that has been collected over a long period in time and that has been collected according to strict controls. The authors present the pitfalls of numerical modelling of the surface flux boundary conditions, as well as present guidelines towards appropriate use of these modelling tools.

Jan 1, 2003

By Hall S. F, Quast K. B Newell R, Ketteridge I. B

For the past six years research funded by the State Energy Research Advisory Commit- tee of South Australia has been conducted at the South Australian Institute of Technology, School of Mining and Metallurgy on South Australian lignites. A major part of this work has been a study of the potential bene- fication of Bowmans lignite using hydrometal- lurgical techniques. The Bowmans lignite de- posit is the largest of its type in South Australia and is a major energy reserve for the state. The utilization potential of this deposit is reduced by its very high insitu NaCl content which presents serious problems for any process. Previous research conducted by Readett and co-workers (1984a & b) has shown that NaCl is amenable to extraction using simple batch water leaching operations. This leaching has been successfully described using a two stage diffusion model derived from first principles based on a simple diaphragm cell.

Jan 1, 1987

By Booth GW, Robertson IG

The Paddington Gold Mine ties within the Norseman-Wiluna greenstone belt, in the celebrated Eastern Goldfields province of the Yilgarn Block, Western Australia. Regionally, tropical to subtropical weathering has effected development of a prominent regolith and a deep lateritic profile. Detailed examination of the clay mineralogy, largely from a single drill hole which traversed the original Paddington I deposit, outlined three separate, vertically gradational assemblages, which are, in part, rock-type dependant. These include; 1. kaolinite with minur to trace quantities of sericite/illite (0-22m), 2. smectite and/or interstratified clay minerals, together with variable amounts of kaolinite, relic chlorite and illite/sericite (22-81m), and 3. chlorite and sericite (> 81m). Near surface, kaolinitic assemblages may be directly correlated with the intensity of lateritization, whereas smectite and interstratified clays from intermediate zones appear in association

Jan 1, 1989

The limitations of the conventional practices, and their effects, in prospecting for and in the evaluation of alluvial gold deposits are briefly reviewed. Geophysical prospecting methods have demonstrated their complementary role in the delineation of deposits by reducing the number of boreholes which are primarily of a 'probing' type. Larger diameter boreholes, although more expensive on a linear basis, are much cheaper on a volume recovered basis. The need to have sufficient volume as well as number of samples is stressed. Classical statistical methods are not appropriate for such deposits as there is sufficient structure, or spatial correlation, to require the application of geostatistics. Quite reliable semi-variograms, but not in all cases, of the spherical scheme have been obtained. Subsequent kriging has, to date, been confined to unworked deposits: retrospective estimates to compare to production have not therefore been produced. However, the technique shows promise but indicates a considerably greater borehole density (of the conventional diameter) may be necessary to produce confident estimates. Used in conjunction with larger diameter boreholes, a lesser borehole density may be sufficient, through radical reductions of the sampling error.

Jan 1, 1977

By B Murphy, J van Zyl, G Domingo

In a narrow vein mining scenario, employing preconcentration technology underground not only results in reduced transport and handling costs but may allow alternative mining methods to be implemented, improving overall productivity. Using processing technology underground is not a new concept with underground crushing and screening operations being quite widely utilised. With advances in processing technology over recent years, there are now a number of robust processing methodologies in existence that are capable of performing separation of ore and waste at a relatively coarse size. Many of these technologies are readily adaptable to the underground environment and if employed could result in a number of cost and productivity benefits.Assessment of the oreÆs suitability for preconcentration technology is the first step in harnessing these potential savings. This paper discusses how coarse ore sorting and gravity separation could be employed underground in a narrow-vein scenario and details the test work that is required at the front-end of a project to see if this potential exists.CITATION:Murphy, B, van Zyl, J and Domingo, G, 2012. Underground preconcentration by ore sorting and coarse gravity separation, in Proceedings Narrow Vein Mining 2012 , pp 237-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Finlayson J. F

The advantages of rapid and accurate analyses are becoming appreciated in many industries today and have resulted in a great increase in the number of samples received by their laboratories. This has caused some firms to consider the installation of one or more of the instruments available for analytical chemistry. In this country there are relatively few people with experience of instrumental methods and it is difficult for a firm considering the installation of such equipment to assess the advantages which instruments may give them, and to decide which instruments, if any, will be of most use to them. The object of this paper is to give a brief survey of instrumental methods in the field of inorganic analysis. Instrumental methods of analysis have numerous advantages when used correctly. They enable extremely rapid analyses to be made in many cases, e.g., analysis of refined lead by purely chemical means takes about two days whereas spectographically the analysis can be completed in approximately one and a half hours. The accuracy ofinstrumental methods, generally between 1 and 5%, is higher than most chemical methods for small percentages of impurities. Furthermore, if the instrument can be calibrated against absolute standards the errors are usually random and not biased to one side of the correct result. The sensitivity is high, enabling in many cases the detection and determination of smaller percentages than can be detected chemically. This high sensitivity enables and, in some cases, requires the use of very small samples, and results in considerable savings in reagents, allowing the analysis of considerably more samples without undue loss...

Jan 1, 1951