Search Documents

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

Acid rock drainage (ARD) derived from sulphide oxidation and the associated metal leaching is the most significant environmental issue facing the mining industry today. Under given hydrological and biogeochemical conditions, the local geology and mineralogy largely control the formation of ARD. The involvement of a geologist is therefore essential in minesite ARD assessment and prevention. The relevant tasks that a mine geologist may undertake at three major phases of a mining project are briefly described. Additional knowledge that a mine geologist should acquire in order to achieve proficiency in ARD assessment is also suggested.

Jan 1, 1993

By Downs M

The use of a cutting machine designed to allow simultaneous cutting and setting of roof supports has numerous advantages few development roads in coalmines. The use of such a machine with the added ability to cut a curved roof profile is of considerable interest for longwall development in thick coal.

Jan 1, 1998

The design, construction and operation of a 500,000 tonne per year Carbon-In-Pulp (C.I.P.) plant at Kambalda embracing the period from 1980 to 1982 has been previously discussed (Sceresini, 1982).Since that time the annual throughput rate has increased to 780,000 tpy.This paper discusses the changes and improve-ment made to allow this increased production to occur with minimal capital expenditure.

Jan 1, 1984

By A B. Bell

The health and in some cases survival of mineral exploration and mining companies is, in today's markets, more dependant than ever on the effective use of information technology. The need for speedy collection, organisation, maintenance and distribution of corporate and project information is a phenomenon that will continue to strengthen with market thirst.Geographic Information Systems (GIS) provide a medium for storage, maintenance and retrieval of data, and Internet Mapping adds a technology for effective distribution of that data. Combining these technologies can return benefits both fiscally and technically by reducing costs of ownership in IT infrastructure and increasing the efficiency and effectiveness of both internal and external information delivery.GIS and Internet Mapping technologies have reached a practical stanza in their evolution and will continue to develop as a key business tool in the natural resources sector.

Jan 1, 2002

By E Y. Baafi

Artisanal and small-scale gold mining (ASSM) offers lucrative employment opportunities to the locals of most developing countries. The major drawback of ASSM is its adverse impacts on the environment resulting from improper mining and processing techniques. Papua New Guinea (PNG) has very active ASSM activities. The artisanal and small-scale gold mining in PNG provide employment at local and national levels and the sector is an important source for inflow of foreign exchange into rural communities. However, small-scale mining activities are associated with sensitive health and environmental issues. The process of recovering gold by retorting and heating the amalgam over an open fire is a dangerous health practice. This paper discusses artisanal and small-scale gold mining operations in PNG and their impacts on the local environment.

Jan 1, 2008

Over a four year period from 1984 to 1987, a broad range of ground conditions were experienced in recovering old workings at the Walhalla mine in central-eastern Victoria. Access to the ore zone was gained via old workings and new development. The work included: Recovery of vertical and inclined shafts. Recovery of collapsed winzes. Recovery of level drives and crosscuts. Spiling through broken ground and old mullock. Pre-grouting of caved zones. New development using small-scale rail equipment and "bobcat" Loaders.

Jan 1, 1988

By Tomlinson R. C

The paper will briefly describe planning in the National Coal Board (NCB) and the contribution that operational research makes to it. It will then give details of some of the models in use and will finally consider critically the problems of looking ahead to the next century.

Jan 1, 1977

As modern techniques of Petroleum Exploration and Development are rela-tively new in Australia,2 the alien terms "Mud Logging" and "Core Analysis" will bear explanation. Mud Logging and Core Analysis are two of the Petroleum. Industryts most useful "tools" in the successful search for, and development of, commercial oil and gas deposits. Modern Mud Logging could be more accu-xately termed "Drill Cuttings and Mud Gas Analysis". Presently, mud-logging has its greatest application in exploratory wells where subsurface geologic control is at a-minimum.

Jan 1, 1962

The relationship between the permeability of coal to a mixture of methane and carbon dioxide, and the permeability to methane and carbon dioxide separately is described in this paper, along with the analysis of the differences in permeabilities of coal to methane and carbon dioxide.

Jan 1, 1989

The Olympic Dam Project constitutes a major resource of Copper and Uranium and has been under intensive evaluation since the discovery in 1975.A 500 metre deep rectangular shaft has been sunk into the deposit and this has been followed by 8400 metres of level, incline and decline development. 5 surface ventilation raises have also been constructed.Large scale trackless equipment is used to carry out the development, and productivity statistics are given.The paper describes the functionalised system used in the development program and discusses the maintenance support, and services required to carry out these works.The objectives of the Exploration Development program and the satisfactory results obtained from this work are also discussed.

Jan 1, 1985

By Muge F, Pereira H

In the early stages of the planning of a new exploitation, the error in ore reserve estimation is an important factor that must not be disregarded. As this error can be computed by geostatistical methods, the risk of the venture can be calculated for different recognition patterns in a certain assumption of economical conditions. A case story is described for an open pit phosphate deposit in which grade/tonnage curves and their confidence intervals are related to an economic function for three drilling patterns and decisions are taken on the basis of cost and value of supplementary information.

Jan 1, 1977

This work describes preliminary laboratory testwork to study the relative leaching response to cyanidation and thiourea leaching of an oxidised low grade gold ore. The potential of an alternative lixiviant like thiourea to commercial processing of mine dumps is discussed by specific reference to selected case histories. It would appear that on the basis of the available published information, there could well be a case advanced for the acid thiourea leaching of sulphide concentrate tailings being subjected

Jan 1, 1994

The Kundana underground narrow vein gold mine had a recent history of large and damaging seismic events. Following a period of seismic events on 30 July 2001, in which nine miners were temporarily entrapped at depth due to falls of ground in several parts of the decline, the mine operation was required to develop a seismic management system to mitigate seismic risk to the operation. A micro seismic systems and boundary element modelling of mine sequence highlighted large-scale footwall faults and the mining of gold bearing shear veins to be focal structures for seismic energy release between depths of 300 m to the base of mining at 650 m. The integration of seismic data, identification of geological structures and mapping of zones of failed rockmass led to the successful generation of a non linear boundary element model and a seismic hazard strategy. This enabled mine sequences to be assessed daily, monthly and periodically for potential seismic hazards and therefore assigned both economic and personnel risks for the recovery of the ore reserve at the Kundana Underground Operation.

Jan 1, 2005

A laboratory investigation was carried out to obtain data on the explosive character- istics of selected coals mined in New South Wales. Seven coal seams were sampled and the volatile matter content of the coals tested varied between 28 and 37 percent. A mod- ified Hartmann apparatus with a volume of 1250 ml was used in the investigation. Dust clou' generation was produced by an air blast delivered radially through a mushroom type valve and the ignition source was a-continuous A.C. spark produced by a 20 000 V, 50 mA transformer. The coal dust parameters invest- igated were the maximum pressure developed, the average and maximum rates of pressure rise at dust concentrations between 200 and 1500 3 g/m.

Jan 1, 1981

By Herbst JA

During the last decade, it has been established that conventional mineral-processing control strategies based on classical control theory result in significant increases in plant throughput and operating-cost saving. The proper education and training of personnel using dynamic simulators of the principal unit operations is vital for proper design and maintenance of control systems. Severe multivariable interactions and numerous constraints on both manipulated and state variables in grinding/classifica-tion and flotation systems can be studied using time domain analysis with proper dynamic simulators. Two interactive programs are described, and the basis of each simulator and its structure are discussed. Two examples concerned with choosing, tuning, and decoupl-ing of manipulated and controlled variables for a grinding/classification circuit (DYNA-MILL II) and for a rougher flotation circuit (DYNAFLOAT II) are presented. The way in which these dynamic simulators can be used for the design of model-based control strate-gies is also outlined. A brief description of the use of these dynamic simulators for screening alternative strategies and circuit optimization is given.

Jan 1, 1985

By C J. Adams, H J. Campbell, T Popham, A Goodall

Pounamu is a MSori collective term for semi-precious stone scientifically referred to as nephrite, semi-nephrite, jade or bowenite (tangiwai) that is composed predominantly of metamorphic tremolite in a felted, fibrous texture. It is Aotearoa/New ZealandÆs icon mineral material. Ownership and management of this important taonga (treasure) has been vested in Te Rnnanga o NgSi Tahu as part of a Treaty of Waitangi settlement process. Increasing demand from the tourist, jewellery, fashion and sculpture industries, as well as cultural renaissance, has placed pressure on the pounamu resource. This had led to nephrite importation, allegations that foreign material is being marketed falsely as New Zealand pounamu, and wider concerns over the potential for exploitation/over-use and theft of genuine pounamu.   Research is underway to characterise different pounamu source regions by defining their ægenetic fingerprintÆ. The geological age and radiogenic isotopic composition of Aotearoa/New Zealand pounamu is distinguished from other nephrite jade occurrences overseas, due to relatively young cooling ages. Strontium isotope ratios distinguish pounamu from different source areas within Aotearoa/New Zealand (whakapapa), with signatures reflecting the host terrane rocks (their family) and their position in a sequence of metamorphic events (their generation). The research will provide a tool for archaeological research, trademark and resource protection.   Mineral resource assessments normally aim to define the total volume/tonnage present, which is generally assumed to be finite, applying drilling and geostatistical modelling. Pounamu resource assessment requires a different approach, as its intrinsic value is insufficient to warrant modern exploration methods (eg drilling, geophysics). Pounamu is only known to occur at a restricted few in-situ (hard-rock) localities. It is primarily found in transported (alluvial) detrital river and glacial outwash deposits, where collectable material has short term variability due to erosion and transport processes. A new methodology is being developed aiming to define: +        the total resource present, +        the relative rate of change in the availability of that resource through erosion and other geological processes, +        active areas where new material is likely to be exposed (eg by erosion), and +        appropriate extraction rates for sustainable use. The methodology will provide a holistic overview of the resource in different regions of Aotearoa/New Zealand, and may be applicable to other transient or restricted natural resources that occur within geologically active environments (eg supplies of driftwood on beaches).

Jan 1, 2005

This paper is a tribute to the late Dr Donald Martin Hausen as a father of applied mineralogy. His dedication to promoting the field through technical societies and through his professional work was outstanding, and his activities as a humanitarian are noteworthy. Dr HausenÆs involvement in technical societies included organising and conducting the only ICAM congress that was held in the USA, co-founding and nurturing the Process Mineralogy Committee within the American Institute of Mining, Metallurgy and Petroleum Engineers, and participating in CAM, the International Mineral Processing Congress, as well as other technical societies. The Process Mineralogy Committee that he co-founded has continuously organised annual meetings in the USA by conducting a series of sessions, and 17 books on the proceedings from those sessions have been published. As an applied mineralogist Dr Hausen solved many problems in exploitation and processing of minerals, metals and materials, especially gold. He helped to find many Carlin-type gold orebodies by outlining targets using alteration halos as determined by X-ray diffractometry, and he defined mineral characteristics that affected gold metallurgy and cyanidation. It is also noteworthy that Dr Hausen and his wife, Mary, opened their arms and home to many foster children and were instrumental in their placement in many homes. They also sponsored refugees from south-east Asia, taught them English, housed them, and provided constant support until the refugees became responsible and independent US citizens.

Jan 1, 2008

By Parker RL

A 250 tons per day ammonia-ammonium carbonate leaching plant is now being operated by Samin Limited, to extract copper from the oxidised ores at the Burra mine. This forms the first stage of a plant, which will eventually have a capacity in excess of 1,000 tons per day. The article reviews the history of the mines at Burra and the metallurgical studies which have been undertaken since the old mines closed in 1917, in an endeavour to recover the copper from the low-grade deposits left by the original miners. The reasons why an ammonia leaching process was selected instead of the conventional flotation or acid leaching methods are discussed. The paper concludes with a detailed description of the plant and the basis on which it was designed.

Jan 1, 1971

By M B. McKevitt, W J. Shaw

The main task of grade control on a daily basis is to define the material that should be mined to a destination under various categories. This can be determined by grade, lithology, quality and blending criteria. In the case of multi-element deposits or deposits with various blending or other processing criteria the optimum selection of ore block boundaries can be quite complex. In every case the balance between ore loss and dilution must be considered when designing the ore block boundaries and this becomes a risk-based decision when using the conditional simulation model. The use of such systems allows grade control to meet specific targets, such as budget tonnages and grades and blended product specifications. Two case studies are presented: the Prominent Hill copper/gold mine and the Rapu Rapu zinc/copper mine. Mining is based on a rational grade control strategy involving a number of factors, including strong geological control, advanced geostatistical approaches, such as conditional simulation, and optimisation of the ore blocking to meet production requirements. This provides an objective, transparent and repeatable grade control strategy.

Jan 1, 2009