Search Documents

The gossan developed from the Whim Creek Cu-Zn-Pb-Ag sulphide deposit, in the Pilbara region of Western Australia, occurs near the top of a ridge in a dissected plateau 01 moderate relief. The gossan is characterized by the abundance of secondary ore minerals which indicates that it is relatively immature, due to climatic conditions and erosional stripping.The abundant presence of secondary carbonates indicates that the low pH generally resulting from sulphide oxidation has been neutralized, probably by the buffering effect of carbonatcs and silicates. Fe, Cu, Pb, 'Ag and Sn have been enriched in the gossan relative to the primary ore, and Mn, Ti, Co and Ni have been strongly depleted; other elements have remained substantially unchanged. The gossan has a strong gcochemical signature characterized by high Cu, Zn, Pb, As, Sb, Sn, Ag and Mo coutents. Boxwork textures are poorly developed, bu't the gossan has other diagnostic mineralogical features including sulphide inclusions in quartz and the presence of residual cassiterite.

Jan 1, 1982

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By McDonald K. J, Flann R. C

A liquid phase sintering (LPS) process for preparing basket anodes from nickel powder has been scaled-up and the innuence of compact green density and sulphur content, as well as sintering conditions (period and syngas now.rate) on the perfonnance of anodes has been evaluated. The product anodes have been tested in an industrial electroplating tank. It is concluded that if anode residues are to be minimised, then with a sintering temperature of 960"C, compact green density needs to be as high as economically achievable (85 - 87 per cent density of solid nickel) and the sintering period approximately 40 minutes. With these constraints, if residual sulphur contents of anodes are to be kept as low as those of commercial anodes, then the sulphur content of the green compacts would need to be less than 1670 ppm. At the same time, it is also found that residual sulphur concentrations as high as 2000 ppm are beneficial to anode pcrfonnancc and not detrimental to the quality of the electroplate. The ability of the LPS process to produce marketable nickel anodes for the electroplating industry is clearly demonstrated.

Jan 1, 1993

By M D. Basuki Dwi Priyono

The Toguraci low sulfidation epithermal gold vein deposits are located 2 km WSW from the Gosowong mine and form part of the Gosowong Goldfield. The goldfield lies within a Neogene magmatic arc on Halmahera Island, North Maluku Province, East Indonesia. The terrain is moderate to steep, rainforested, and poorly outcropping. Exploration and mining operations are being carried out within the PT Nusa Halmahera Minerals Contract of Work (exploration tenement) jointly owned by Newcrest Mining Ltd (82.5 per cent, operator) and PT Aneka Tambang Tbk. (17.5 per cent). First pass exploration of the Gosowong area began late 1992 resulting in the discovery of weakly developed porphyry copper mineralisation (named Bora) at Toguraci in 1993. Early in the evaluation of this porphyry an overprinting epithermal Au/Ag mineralisation event was recognised, however exploration focus remained on the Bora porphyry deposit for some time. The discovery of the nearby Gosowong epithermal gold deposit and the exploration of other prospects in the area further diverted attention and funds from Toguraci. It was not until year 2000 that Toguraci was seriously reevaluated as part of a detailed appraisal of the epithermal gold potential within a 5 km radius of the Gosowong gold mine. A fly-camp based drilling campaign using man-portable rigs was undertaken between August 2000 and March 2002. All exploration at Toguraci was then stopped pending government approvals to mine. These were finally issued in May 2003 and immediately drilling restarted and pre-mine approvals (eg the environmental impact study) were sought and granted. The first Toguraci gold bar was poured in February 2004. Exploration at Toguraci and elsewhere in the Gosowong Goldfield continues today.

Jan 1, 2004

Atlas Copco is one of the worldÆs leading providers of industrial productivity solutions (Atlas Copco, 2009). Furthermore, the company spans 160 markets and held 34 000 employees at the end of 2008. The company is organised under three ætechniquesÆ whereby the Construction and Mining TechniqueÆs business division is located within +rebro, Sweden. This paper is aimed at briefly facilitating information on how the company and more specifically, the Construction and Mining Technique is run. Also, by sharing my experiences, this paper is intended to encourage and motivate students currently studying for a degree relevant to the minerals industry, to apply for this extremely beneficial scholarship. Through a number of presentations relating to the various divisions, products and aftermarket services of the company, I came to realise that Atlas Copco extends beyond simply selling equipment suitable for the mining and civil industries. This tour through Sweden also contained highlights of visiting the Underground Rock Excavation factory, Surface Drilling Equipment factory and Secoroc divisions. I was also fortunate enough to participate in a tour of the LKAB mine in Kiruna. In addition, time was allocated to less industry related activities, and I was able to go dog sledging, sip vodka cocktails out of ice glasses at the Ice Hotel and enjoy traditional Swedish foods of moose and reindeer. Most important and memorable to me; however, was the ability for employees of Atlas Copco to speak of the company and their products with such passion and enthusiasm, which truly made this a motivational and unforgettable experience.

Jan 1, 2009

By Coin CDA

From a study of coke samples obtained from the tuyere level of four Australian Blast Furnaces, the nature of in-furnace coke degradation has been investigated. At the periphery of the raceway is a concentration of fines and the lump coke appears dull and rounded. However coke from the deadman is angular and relatively undegraded. Cokes made from higher rank coal appear to suffer preferential attack of the reactive maceral derived component (binder). The coke from lower rank coal appears to be attacked non-preferentially by the solution-loss reaction. Initial attempts to simulate these phenomena have given results consistent with these findings. From chemical analysis of the tuyere probe samples there appears to be a relative increase in carbon and decrease in-.sulphur and phosphorous between stockline and tuyere level. An overall decrease in coke mineral matter derived material was noted and associated with this was a significant gasification of silicon. Consequent formation of silicon carbide was noted.

Jan 1, 1981

By G Johnson, S Michalek, N Redman

As the modification of the 2009 Mill OperatorsÆ Conference theme from æmilling through the boomÆ to æthe boom û experience gained and lessons learnedÆ exemplifies, comminution practitioners are facing a series of challenges in the dramatically changing mining environment. One of the main problems plant managers have been facing during the boom times has been the severe metallurgy skills shortage and high staff turnover, both factors that can cause difficulties in mill liner management. Many of todayÆs mill managers are now also more than ever faced with the need for cost-cutting in order to continue operating viably. Amongst other potential target outcomes such as maximised throughput, MillMapperÖ, a tool for mill condition monitoring and mill performance optimisation, can be utilised to address these issues. This paper demonstrates how MillMapperÆs quantifying decision making tools can serve to be in control of managing mill liner and production issues, and how it can form the basis for mill cost savings without the risks normally associated with conventional methods or the lack of using any condition monitoring methods. MillMapperÖ is currently being referred to at a rate of approximately 150 surveys and associated reports per annum at processing plants in Australasia, South America and Africa. Examples throughout the paper provide insight into how the presented sample set of users have extracted benefits that could have otherwise not been safely or at all achieved.

Jan 1, 2009

By Gyasi-Agyei Y

In recent years rapid advances have been made in the technology used for hydrology and erosion modelling of rural catchments. These advances have been driven by the growing availability of digital terrain maps that can be used to automatically define catchment properties that previously had to be manually extracted from contour maps. In addition, these models have, in principle at least, more powerful predictive capability. The author is involved in a number of projects to migrate and further develop these models for application to mine rehabilitation assessment. Current technologies for hydrology and erosion assessment (eg CREAMS, ANSWERS) are reviewed, underlying principles highlighted and deficiencies in the context of mine rehabilitation design assessment addressed. The advantages and disadvantages of the new digital terrain map tools (eg WEPP, SIBERIA) are discussed. Current work integrating these new models with existing rehabilitation design tools (eg ACIRL's ARGUS computer package) highlights the advantages of an integrated approach using digital terrain maps; cheaper, faster, lower impact and more flexible rehabilitation design. The use of novel visualisation tools to aid the design process is discussed. The paper is illustrated by applications to mine sites in Queensland and the Northern Territory.

Jan 1, 1995

By J-S Zhang

In this paper, the author briefly introduces the resource characteristics of Chinese iron ore, as well as the present increasing market demand for iron concentrate. The SHP-3200 wet high-intensity magnetic separator (HIMS) is used to separate complicated weak-magnetic iron ores being composed of specularite, limonite and siderite in Jiuquan Iron and Steel (Group) Co Ltd. Some technologies have been used to improve SHP-3200 HIMS, including modifying the angle of magnetic polar from 90¦ to 83¦, cooling the exciting coils by oil instead of air, adding reverse-washing equipment to wash off magnetic particles and adjusting the tooth-space of the matrix from 5.0 mm to 3.5 mm or 2.5 mm to enhance the recovery of fine particles. It is still difficult to meet the requirement for recovering more difficultly separated iron and the demands for high-grade concentrate of iron. In order to improve the recovery of difficult-separated iron, the film-magnetic separation technique is applied into the HIMS and a new LY matrix is designed to form magnetic gradient vertically. A flowing-film feeder is also added and the feed mouth is modified to make a slurry flow formed in the form of film along the wall of matrix. The microstructure and dissemination character of the mineral particles is studied, and the specific susceptibility of the primary minerals is measured. Then the distributive characteristics of a magnetic field for the separator with film-magnetic technique and the motion of particles in the process of separation are all analysed. By introducing the film-magnetic separation technique to SHP-Φ700 HIMS, the recovery of iron can be raised from 69.45 per cent to 76.07 - 78.96 per cent with the similar grade of concentrates of iron. Such an increase of 9.51 per cent in the recovery also shows that it is feasible for such film-magnetic separation technique to be applied into HIMS.

Jan 1, 2005

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

Longwalling has reached a high standard both in Germany and Australia and most improvements should be expected in planning, monitoring and control. Double drum shearer have electric drives to 1000 kW and automatic height control is under development. Conveyor pans to 40mm thickness and chains to 2300 kN breaking load are in use with controls for pretension and load compensation under test.Trends in support are towards two leg shields with loads to 3850 kN per leg and electrohydraulic controls. Expert systems have been devised for planning and diagnosis tasks. With increases in technical standards, staff qualification standards at rising too, drawing attention to training requirements for modem personnel.

Jan 1, 1991

This paper forms part of a series of papers relating to the Melbourne Underground Rail Loop and presented to the Fourth Australian Tunnelling Conference in Melbourne, March 1981. The Design of Electrical and Mechanical Services in Museum Station and adjacent Running Tunnels and their relation to Rail.wruy Operation through the Loop are described. The descriptions, while specific to Muscrio Station, are generally representative of those being provided at Parliament and Flagstaff Stations. The Museum Station comprises some 6500 square metres of platform and track area, 5000 square metres of booking hall concourse and entrances and 1200 square metres of offices and plant rooms. The Mechanical and Ilectrical Services for this complex are .imilar in many aspects to those of a large !.gr.hrise city building, but in general the i::;ign is directed more strongly towards :.arety, durability and reliability, and subject to many restraints imposed by L'mitations of space and accessability.

Jan 1, 1981

TABLE OF CONTENTS:Introduction.Chemical Composition-lignitic coal-earthy coal-pollen coal-fern coal-nature of ash in the several coal types.Carbonization Tests.Air Drying of the Coal Types-rate of drying in the coal face-relative rates of diffusion-differential slacking of coal types-rate of oxygen absorption.Origin of the Coal Types-colour difference-cause of different rates of diffusion.Practical Significance.Summary.Acknowledgments.The Yallourn brown coal seam, where exposed in the Yallourn Open Cut, and the Latrobe brown coal seam, where exposed in the Yallourn North Open Cut, are both distinctly bedded. Close inspection shows that both seams consist of beds of coal from 1 to 10 ft. thick, which on drying out develop differences in colour and in their, shrinkage crack patterns. Tliese differences become apparent in the...

Jan 1, 1947

By D Chalmers

Drill and blast mining techniques are used to mine coal outburst prone and high gas content coals in Australia. As the risk of an outburst is increased in high gas content coal, it is considered that drill and blast is the safest way to mine coals that refuse to yield gas even after considerable gas drainage efforts. The availability of suitable explosives for drill and blast in Australia is dependent on the æBuxtonÆ tests. With the diminished coal operations in England, the type and supply of such explosives is tenuous, causing significant disruption to the production of coal in some mines. In an attempt to free up the availability of explosives a review of the methods used for the testing of coal mine explosives was undertaken to ascertain the scientific basis for these tests. It was hoped that this comparison would allow regulators to have the confidence in explosives that had been tested elsewhere. Although this was not achieved, it has spawned a major research project that aims to better understand the mechanisms involved so that either confirmation of the current testing regime can be achieved or more suitable and scientifically based tests can be adopted. This paper looks at the ongoing research program investigating the parameters that are involved with methane ignitions from explosives. By utilising high-speed data capture and processing the research project is trying to view an ignition as it happens to identify the mechanisms involved so that better explosives can be designed for the coal mining industry.

Jan 1, 2007

By Beech-Jones J. M

At Port Latta in Tasmania, Savage River Mines operates vertical shaft furnaces for the firing of pelletised magnetite concentrates. At times the temperature profile of the furnace has changed markedly, necessitating the- burning of greater quantities of fuel to maintain good pellet quality. A study of the oxidati=of magnetite concentrates was under- taken because this exothermic process supplies much of the heat required to indurate the pellets. Using the thermal analyses methods, different magnetite concentrates from Australian and overseas were heated in air under identical conditions, to compare rates of oxygen uptake and of heat release. In addition, a compari- son was made of the oxidation behaviour of different particle size fractions of a selected concentrate. Particle size analyses, x-ray diffraction and dilatometer tests were used to aid inter pretation of the thermal analysis traces. The investigation emphasized the importance of particle size and ferrous iron content in determining' oxidation rates from the commencement of heating.

Jan 1, 1974

For several decades miners have been obliged to maintain a vast supply of sharp steels at the working face to meet the hungry needs of rock-drills. In medium and large size mines this has meant the setting up of an organisation to store steels, to make and sharpen bits with all the complication and skill of forging, hot milling and heat treatment, and to transport sharp and dulled steels to and from the working face with all its labour, wastage, and inconvenience to other mining operations.In a mine with 250 rock-drills in use, a flow of more than 60,000 sharpened steels each month has to be maintained to keep the machines fully employed, so some idea of the magnitude of this problem may be grasped.For a long time it has been apparent that it is mainly the bit itself that wears, and many attempts have been made to reduce the enormity of the problem by providing detachable steel bits which could either be used once and rejected, or sharpened three or four times before rejection.At the same time metallurgists have striven to 'improve the quality of the steel and the heat treatment afforded it so that a bit, readily workable In a normal mine drill-shop, could be produced having a high resistance to wear and fatigue; but, although various alloy steels have been marketed, it is still usual to find many mines relying on a "straight" carbon (0.6 - 0.9% C.) steel for their drill steels.Since 1915 increasing use has been made of tungstencarbide as a cutting implement in the engineering industry. Where, on account of its great hardness and long life, it...

Jan 1, 1948

Coal Mining machinery has undergone enormous changes in design and complexity of controls in the past 10 years. Specialised, high productivity equipment has been manufactured in Australia, in sufficient volume, to satisfy the local mullet needs.Local manufacturers face greater challenges from overseas competition, as well as increased customer demands to improve machine performance, productivity, quality, reliability and safety. In order to meet these demands now and in the future, it will be necessary to review work practises, and restructure production and quality systems to incorporate the latest principles and philosophies.

Jan 1, 1991

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

By Napier-Munn T. J, Morrison R. D, Moloney M. J, Corrans I. J

A dynamic simulator for CIP / CIL gold recovery plants has been developed at the Julius Kruttschnitt Mineral Research Centre within a collaborative, industrially - funded AMIRA project and with the participation of the Western Australian School of Mines. The simulator incorporates kinetic models for the leaching of gold from ore and its adsorption onto activated carbon, and the residence time distributions of the leach liquor, pulp solids and carbon in the circuit. Features of the simulator include the effects of gold loading distributions on both the ore and carbon on reaction rates, and the difference in residence time distribution between the leach liquor and pulp solids. The simulator allows for the estimation of kinetic model parameters from full scale applications, as well as some scale - up of parameters from laboratory batch tests. The laboratory tests were conducted at the WASM as part of the collaborative research project. The simulator can operate in both steady - state and dynamic modes, and has potential applications in design, optimisation and control of CIP / CIL plants.

Jan 1, 1991

The Drake-Rivertree area lies in the far north east of the New England district of New South Wales. Drake is some 500 miles north of Sydney by road and 36 miles west of Lismore. Rivertree is situated 24 miles north of Drake.The Drake deposits were first worked in 1878 for gold which occurred in a very fine state in ferruginous gossan but at depth copper ore became more significant. The lodes at Rivertree, discovered in 1887, were worked for silver but mixed sulphides became more prominent in deeper levels.Several mines operated at each centre and each locality smelted its own ore.The mines at both centres were operated sporadically for many years though production was not particularly substantial.A number of the larger mining companies have shown a recent interest in this mining field with special emphasis on the Drake locality.GENERAL GEOLOGYThe two mining centres are situated to the north and south respectively of a belt of Permian marine sediments and volcanics similar to, and probably representing an easterly extension of, the rocks of the Emmaville district further west.E. C. Andrews (1907) recognized two stratigraphic units within what he called the Drake Series. The Lower Division consists of rhyolite flows, tuft's, breccias and agglomerates, followed by trachytic and andesitic tuft's containing cladochonns, thanmopora willcinsoni and other Permian forms.

Jan 1, 1962