Search Documents

By A K. B Opitz, M Becker, J L. Broadhurst

"One of the key drivers of geometallurgy is to define the ore characteristics and their variability to build a geometallurgical model. The inclusion of waste rock properties and their variability is just as important, given that the generation of acid rock drainage (ARD) poses one of the most significant environmental challenges facing the mining industry. Formed through the oxidation of sulfide minerals in the presence of oxygen and water, ARD generation is exacerbated through the regeneration of lixiviates by naturally occurring iron- and sulfur-oxidising micro-organisms. In order to manage the potential risk of ARD pollution, timely, accurate, reliable and robust characterisation and prediction of the ARD potential of waste material is critical from an early stage in the mining process.This study demonstrates the use of the biokinetic-accelerated weathering test developed at the University of Cape Town to characterise the ARD potentials of gold waste rock samples under microbial conditions. These tests are performed in conjunction with standard characterisation tests to provide an indication of the potential for ARD generation under both chemical and biological conditions. Results provided information regarding the relative rates of acid neutralisation and acid generation, with the contribution of specific minerals to the observed behaviour considered through use of a detailed mineralogical assessment. Overall, the addition of the biokinetic test to the current geometallurgical characterisation and prediction toolbox will allow for relatively rapid assessment of the bulk kinetics of ARD generation.CITATION:Opitz, A K B, Becker, M, Broadhurst, J L, Bradshaw, D J and Harrison, S T L, 2016. The Biokinetic Test as a Geometallurgical Indicator for Acid Rock Drainage Potentials, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 183–192 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By I Canbulat, G Si, Y Duan, X Luo

The presence of unfavourable geological structures such as faults and dykes often can contribute to coal burst risk. Seismic events associated with rock fractures tend to cluster around these structures and it is important to understand the characteristics of seismicity for coal burst risk management. In an Australian underground longwall coalmine, two clusters of seismic activities close to the longwall face and within a section of the maingate roadway which was intersected by a major dyke were respectively identified. The induced seismicity in the dyke-roadway area was closely related to the longwall mining. These seismic events were located and the distribution of seismic events shows that more fractures were distributed on the inbye side of the dyke. The spatial-temporal changes of the seismic event locations delineate the fracture propagation as the longwall mined through the dyke. The frequency-magnitude relationship of seismicity was analysed and it was found that it changed significantly when the longwall was mining towards, through and past the dyke. The monitoring results demonstrate that because of the stiff dyke, the seismicity was intensified in the roadway section. It proves that the dyke promoted stress re-distribution and seismicity in its vicinity. More fractures were induced in the hanging wall of the dyke, whereas less strain energy was accumulated and released in the footwall of the dyke.

Nov 29, 2022

By D Giurco

This paper presents the results from research undertaken in the CSIRO-funded Mineral Futures Collaboration Cluster on developing a future vision for the mining and minerals industry – Vision 2040 – in which the industry proactively contributes to long-term benefit for communities and the nation. Our research finds that Australia is currently experiencing mining-led prosperity due to high commodity prices, yet underlying this are challenges for maintaining market share due to lower productivity from extracting lower grade, more remote and complex ores. Whilst much focus has been on developing new technologies for finding and processing such ores, this paper assesses these activities, together with policy and market innovations in the context of needing to strengthen social, environmental and financial capital for long-term benefit. Vision 2010 sees mining activities linked to systems that are net providers of clean water, energy and ecosystem services, rather than minimising negative impacts alone; sovereign wealth funds are used to harness current prosperity for future innovation. Using a case study in lithium and comparisons to iron/steel, coal and copper – we illustrate the opportunities for new technology, policy and market innovations to link the mining and minerals sector in Australia to more sustainable patterns of production, consumption and prosperity.

Nov 22, 2011

Mine evaluation methodologies are well suited to evaluating many projects in capital-intensive industries other than mining. These industries include oil, gas, power generation, transport and infrastructure projects. A case study of an open cu

Jan 1, 1998

By M D. Urbani

HiTec Energy Ltd has been conducting research since 1996 into novel process routes for the treatment of low-grade and waste manganese sources for the production of high value and high quality electrolytic manganese dioxide (EMD) for the alkaline battery market. HiTecÆs approach is to treat previously unsaleable manganese deposits and mine site tailings using a novel sulfur dioxide leach route, followed by purification and electrowinning to generate the sought-after EMD product by an environmentally superior processing route to those presently practiced throughout the world today.HiTec Energy Ltd expects to be in commercial production with its Stage 1 facility in Kalgoorlie in the last quarter of 2004 for the production of 12 500 tpa EMD. With this production facility being adjacent to a laterite nickel producer with available waste manganese units, the opportunity arose for HiTec to combine its existing technologies with processes (that will be discussed in this paper) to turn two waste by-products into products that are used for high-tech purposes.HiTec Energy Ltd and the Parker Centre have had a collaborative research relationship for a number of years in areas involving EMD and battery related technologies. Meanwhile the solvent extraction (SX) group of the Parker Centre (CSIRO Minerals) has developed SX processes to separate manganese from nickel and cobalt. A project was initiated by HiTec Energy to recover manganese from waste laterite leach solutions using SX technology. Batch tests were conducted to select a suitable organic system for the extraction of manganese in terms of selectivity and extraction and stripping kinetics.A total of eight organic systems were tested by determining pH isotherms of metals using a laterite nickel process waste stream. Two organic systems, the Versatic 10 and Versatic 10/synergist systems, were chosen for further test work with Shellsol D70 chosen as the diluent for both systems.The Versatic 10/synergist system would be advantageous over the pure Versatic 10 system because fewer SX stages are required, resulting in a smaller organic inventory and lower capital costs. The risk of gypsum formation is also significantly lower with the synergistic system.

Jan 1, 2004

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

By D Bradshaw, E Forbes, M Edraki, M Tayebi-Khorami, E Manlapig

There is an increasing trend in the extraction and development of copper resources from complex deposits. These deposits pose mineral processing challenges, as they often contain low grade disseminated copper ore with high levels of impurities particularly arsenic. Although arsenic is a naturally occurring element, the concentrations of arsenic can be magnified by mining and mineral processing activities. Therefore, while arsenic has no significant market value, its presence in the ore deposit will have production, environmental and human health implications. The mining industry’s approach to life-of-mine planning has improved significantly in recent decades and managing arsenic is not an exception.CITATION:Tayebi-Khorami, M, Edraki, M, Manlapig, E, Forbes, E and Bradshaw, D, 2018. Arsenic pathways in copper mining – sustainability issues and potential solutions, in Proceedings Life-of-Mine 2018, pp 60–63 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

In late 1984, Council of the Australasian Institute of Mining and Metallurgy accepted a proposal to establish a Mineral Heritage Committee. This was to be involved in matters relating to mineral heritage-its recording, its preservation, and the acknowledgement that it can be of use to the mineral industry in the future. The Committee was established to ensure that all of the disciplines of our profession were included and that, so far as possible, all of our country as well as those countries of the Southwest Pacific Basin were represented. Some work has been commenced to bring real- isation of the importance of the heritage of our mineral industry to the forefront of the commu- nity's interest. There is not a state in this country and the Southwest Pacific where the mineral industry has not at various times proved to be the basis of community development.

Jan 1, 1987

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation: W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

Obtaining correct assays for gold determinations relies on the correct methods being chosen and the assayer being made aware of the mineralogy of the sample and its general origin. Usually when a geologist or metallurgist obtains "incorrect" gold assays the problem can be traced to poor communication between the geologist or metallurgist and the assayer.

Jan 1, 1986

By Armstrong M

The highest grades of the Porgera gold deposit, Papua New Guinea, are contained in Zone 7 due to the presence of the Roamane fault, which acted as channelway of the gold-bearing fluids. Prior to the development and underground mining of this fault-controlled high-grade zone it was critical to provide grade estimates of relatively small mining units, and of the proportion of mining units above cutoff. To be applicable to Zone 7 of Porgera a grade estimation method should account for the following:1. the highly skewed and apparently lognormal distribution of the grades,2. the rapid drop off of the local mean grade and the variance as the distance to the Roamane fault increases,3. the presence of high grade pockets in the footwall, away from that fault, and4. the existence of variograms for the logs with sills parallel to the fault and without sills perpendicular to it.

Jan 1, 1990

By Elford H. S, Hughes J. F

The object of this paper is to bring before Members of the lnstitute the very important and much discussed question of scientifically prospecting for ores, oil, coal, etc.The paper is divided into three sections:SECTION l - Description of Geophysical Prospecting methods.(1) Sound-Vibration.(2) Magnetic.(3) Gravitometric.(4) Electrical.(a) Equipotential.(b) Electro-magnetic.(c) Schlumberger.(d) General.SECTION II - General discussion of Cicophysical Prospecting.SECTION III - Appendices.(1) Systematic summary of methods of survey.(2) Table of electrical conductivities.(3) Bibliography.SECTION I - DESCRIPTION O:F GEOPHYSICAL PROSPECTING METHODS.(1) SOUND-VIBRATION.THE transmission of sound waves or vibrations underground will depend on at least three factors: (a) Type of Rock. - Hard, dense rocks wiII transmit sound waves much more quickly than softer, more porous rocks. In the former the speed may be eight times that of the latter.(2) Uniformity of Rock. - Any variation in the texture, hardness, etc, wiII have an effect on and direction of transmission of the waves.

Jan 1, 1927

The South Wall Base Case Design for Mt Whaleback indicated that along portion of the South Wall a cigar shaped synclinal keel, contain- ing 14 800 m', of Dales Gorge Member ore, would be unkeyed and bed- ding undercut. The dry "ore lobe" slope would be 60m high, unbenched and approximately 170 m long. Stability analyses using specific design parameters established that artificial reinforcement could stabilise the slope and be economically justifiable. To implement the slope design reinforcement for such a complex geo- logical structure it was necessary that all functions pertaining to slope excavation be integrated and co-ordinated within the Mine Geotechnical Section. The objective being to minimise slope damage and thereby optimise the effect of design reinforcement. The successful excavation of the ore lobe in 1988, three years after the introduction of artificial reinforcement, was achieved by strictly main- taining the following parameters. 1. Accurate Geological Model 2. Controlled Perimeter Blasting 3. Controlled Excavation Techniques 4. Quality control -Reinforcement Installation 5. Additional Reinforcement.

Jan 1, 1989

By Hosking IA, Mirkov P

Among the solutions currently being considered for improving traffic flow in Sydney are the construction of major road tunnels, principally the Eastern Distributor Tunnels, leading from the end of the Cahill Expressway to Drivers Triangle and South of Taylor Square and the Sydney Harbour Tunnel, which incorporates sections of driven tunnel at the northern and southern sides of the harbour. The Eastern Distributor Tunnels, known as Stages 2 and 3 of the Eastern Distributor Scheme comprise: Stage 2 - A south bound two lane tunnel from north of William Street to Driver's Triangle. The southern end includes two Y junctions (locally 3 to 4 lane widths) with exits into South Dowling Street, Anzac Parade and Moore Park Road. Stage 3 - A north bound, two lane tunnel from Taylor Square to Palmer Street just north of William Street. Further details of the Eastern Distributor Tunnels are given in the paper by Baxter, Chappel and Fishburn (1986) which is included in this conference.

Jan 1, 1987

By Hendrix JL, Nelson JH

Three ores (sulfidic, oxidized and carbonaceous) were analyzed to determine the effects of leaching time, ore depth, and ore mineralogy on cyanide species concentration. NaCN solutions were percolated through opaque columns filled with milled ore. Column design made liquid sample collection possible from various depths at specific times. The concentrations of weak acid dissociable(WAD) and total cyanide, Fe(CN)63 , Fe(CN)64 , SCN , and Cu(CN)43 were determined for each sample. Extended percolation time led to increases in WAD cyanide concentra- tions and decreased SCN and Cu(CN)43 concentrations regardless of ore depth. WAD cyanide concentration decreased while Fe(CN)64 concentra- tion increased with ore depth. Highest concentrations of Fe(CN)64- SCN and Cu(CN)43 were found in the sulfidic ore, with expected low WAD cyanide concentrations. Lowest concentrations of Fe(CN)64 , SCN 3 and Cu(CN)4 were found in the oxidized ore. Intermediate concentra

Jan 1, 1988

By I Arburthnot, N Lawler, C Loan

The function of a thickener is to optimise and accelerate the process of gravity sedimentation. The desired end product (be that maximised concentrated solids or clarified liquid) determines how the thickener is designed and operated.Significant internal research, together with extensive on-site piloting, by Outotec has resulted in the determination that the application of the appropriate amount and type of shear to hindered settling aggregates can result in a substantial change to the sedimentation process. A new patented technology, called shear enhanced thickening (SET), has been developed. SET results in considerable design implications for full-scale thickeners, including a substantial reduction in required footprint and/or significant increases in underflow density.The development of SET, combined with laboratory and pilot scale verification, will be discussed along with the introduction of this technology to a number of full-scale thickeners. The associated implications and benefits for industrial thickeners are outlined.CITATION:Loan, C, Lawler, N and Arburthnot, I, 2012. Industrial scale results from shear enhanced thickening technology, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Khosia NK, Ravishankar SA, Sankar TAP

Alumina reduction in Rajhara iron ore slimes essentially involves separation of hematite from gibbsite in relatively coarser fraction and from kaolinite in the finer fraction. Selective dispersion flocculation studies on synthetic mixtures clearly indicated that while it was possible to achieve almost perfect separation of hematite from kaolinite using starch and PAMX (modified polyacrylamide containing hydroxamate functional groups) flocculants, no selectivity was observed in iron oxide-alumina system. A schematic flowsheet suggested on the basis of this work for the beneficiation of Indian ore slimes thus consists of classification in a hydrocyclone, followed by selective dispersion of coarse fraction (underflow) and selective flocculation of the overflow fraction. Starting with a feed assaying 46 per cent Fe and 11.6 per cent A1203, a concentrate assaying 60 per cent Fe and 4.7 per cent A1203 could be produced at an overall iron recovery of 60 per cent using conventional Reagents.

Jan 1, 1993

By S B. Martin, M P. Simpson, J L. Mauk

The Martha deposit in Waihi, New Zealand, is a giant adularia-sericite epithermal gold-silver deposit that formed 6.0 to 6.1 Ma, and has produced over 6.4 Moz gold and 39.9 Moz. Fluid inclusion analyses were undertaken on a limited number of vein samples from Martha. The results from this eight week student project are preliminary but agree with previous studies. There is little variation between primary and secondary inclusions and between different vein types, except that homogenisation temperatures of the inclusions in sphalerite grains are on average 20¦ to 30¦C higher than the average quartz vein values. Overall the temperatures of homogenisation ranged from 182¦ to 258¦C and final ice melting temperatures ranged from 0.0¦ to 2.8¦C. Unusual black inclusions were also found associated only with the ginguro bands. Some of these appear to be solid sulphide inclusions but others are not so clear.

Jan 1, 2007

By Rashad MZ

The evaluation of ore deposits consumes much effort, cost and time, hence research work must aim to minimize these inputs with no loss of accuracy. The present study is devoted to assess the optimum conditions and methods of calculations which give minimum costs of ore exploration. An area of (a x a) where "a" is the zone of influence of the semi-variogram, i.e. (2800 x 2800 square metres) located within the Abu Tartur plateau is the subject of the intensive study. The distances between boreholes are varied ie. a/4, a/6, a/8 and a/ 10 respectively. The average ore grade (G), thickness (t) and relative ore reserves (tG) are calculated by four methods. The results indicate that at a distance equal to a/5, the inverse distance squared method gives the best results. These parameters save about 50 percent of the cost of exploration with a map accuracy greater than 90 Percent.

Jan 1, 1987

The purpose of this paper is to explain the basic structure of how minerals are marketed, whilst highlighting the essential factors that mine management needs to be confident are incorporated into a mineÆs marketing strategy. The traditional mine management approach to marketing has been to defer its scrutiny to the marketing manager and take a largely passive role. It is this paperÆs assertion that mine management needs to become more proactive and provide greater strategic input into the marketing process. Irrespective of what mineral your mine produces, the key marketing principles remain constant and need to be understood and managed to extract the full benefit on behalf of the mining asset. From a mine management perspective, success is ultimately linked to understanding these marketing principles and ensuring that they are effectively addressed by your mineÆs marketing strategy. This paper will unashamedly attempt to simplify marketing by explaining how the basic fundamentals of supply and demand set market direction, the importance of a comprehensive marketing strategy, the importance of customer relationships and how contracts and prices are typically negotiated. This paper will use examples from the metallurgical coal (met coal) industry to highlight these points. The paper will also provide a template for developing the critical mine interaction that needs to exist between the marketing department and management to develop a æwhole of mineÆ approach to marketing. It is this core group that will be strategically responsible for delivering the commitments your mine has made to your customers. For mine management not to be actively involved in this process puts at æriskÆ the hard won production and cost efficiencies achieved at your mine and ignores the opportunity to maximise your current and future revenue streams. And whilst this paper recognises that is arguably unreasonable for mine management to become æmarketing expertsÆ, it also argues that it is unreasonable for a mine management to divorce themselves from the process.

Jan 1, 2006