Search Documents

By N Khalili, J Zhao, G F. Zhao

Toppling failure of a jointed rock slope was studied by using the distinct lattice spring model (DLSM). Compared with the classical discrete element model, the DLSM has the advantages of free calibration of micro-mechanical parameters and easy to represent discontinuities, and is more computationally efficient. In this work, the DLSM was used to investigate the toppling failure of jointed rock slopes. The numerical simulation was verified against experimental data from a centrifuge model test on a jointed rock slope. Both the horizontal deformations and failure pattern observed in the centrifuge test were reasonably reproduced using the DLSM. Then, the mechanism of the flexural toppling failure was studied numerically by using a parameter analysis. Finally, some insights were derived that may be useful for practical engineering.CITATION:Zhao, G F, Khalili, N and Zhao, J, 2014. Application of the distinct lattice spring model on toppling failure of a jointed rock slope, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Grady PO

The longwall panels at Clarence Colliery have experienced intermittent sudden weightings on the face that have caused some production delays. These weightings have typically been more severe on the wider faces. A program of surface subsidence and extensometer monitoring was undertaken above Longwalls 4 and 5 to investigate the behaviour of the overburden strata during longwall extraction on two faces of different widths.The monitoring indicated that a dome shaped zone of large downward movement extends up into the overburden strata to a height equal to about the panel width.

Jan 1, 1998

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

Seam gases are the most important atmos- phere contaminants in Australian collieries, their importance increasing with depth; C02 as well as CH4 may be important in intruded envir- onments. The generally high rank of the coal, with low moisture content, makes for abnormal dust production. The other contaminants are introduced and subject to better control, in- cluding products of spontaneous combustion. Due to market situations the generally lower rank and higher sulphur coals more prone to self heating are mined less. Future mining at greater depths should see greater problems with atmosphere contaminants.

Jan 1, 1983

By Williams DJ

Preliminary calculations suggest that spoil piles in the Bowen Basin will undergo approximately 4 m settlement as the ground water table recovers after mining is abandoned. Approximately 1 m of differential settlement is possible. Superimposed on this will be a long term creep settlement of 1-3 m/log cycle of time. Depending on the nature of the spoil material, partially submerged spoil piles could be sufficiently stable although to ensure stability during long term creep it may be necessary to flatten the final spoil pile face to approximately 25¦.

Jan 1, 1987

By Groudeva VI

The biohydrometallurgy of gold is based on different processes which could be grouped into four main groups (Attia, Litchfield and Vaaler, 1985; Karavaiko et al, 1988; Groudev, 1990): 1. bacterial oxidation of gold-bearing sulphide minerals by chemolithotrophic bacteria to facilitate the subsequent chemical extraction of gold; 2. solubilisation of gold from oxide ores by means of heterotrophic bacteria; 3. recovery of gold from solutions by biosorption; and 4. microbial modifications of the surface of gold-bearing sulphide minerals to improve the subsequent gold concentration by physical dressing methods (eg flotation, oil agglomeration).

Jan 1, 1993

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By C Zhang, G Si, J Oh, X Zhu

The presence of rock joints has a huge impact on the strength, deformability, and permeability of fractured rock masses by providing surfaces of weakness on which further deformation are more prone to occur, and by serving as the major channels of water flow due to low matrix permeability. In earlier studies, water flow-through rock joints is often assumed as laminar flow between two ideal smooth parallel plates, and the well-known cubic law was derived and widely used to characterise the hydraulic behaviour of rock joints. However, natural rock fractures are irregular and of spatially varied aperture. Thus, the concept of equivalent hydraulic aperture was introduced to modify the cubic law. Numerous works have been conducted on the relation between hydraulic aperture and mechanical aperture incorporating various geometrical parameters. The surface roughness is one of the most sensitive factors for water flow-through rock joints. The aperture distributions are irregular in natural roughed fractures relative to the parallel plates. Barton et al (1985) and Olsson and Barton (2001) incorporated the joint roughness coefficient JRC in evaluating hydraulic aperture and proposed an empirical equation based on fluid flow tests. However, their equations do not conform to the dimensional consistency. Many other researchers (Zimmerman and Bodvarsson, 1996; Xiong et al, 2011; Li et al, 2019) considered aperture distributions in their equations. But the aperture distributions change during shear was always neglected. The contact of rock joints also has a significant impact on the hydro-mechanical behaviour of rock joint, since fluid tends to flow-through a rough joint along connected channels while bypassing the contact obstacles with tortuosity. Nonetheless, previous research mostly considered joint roughness or aperture changes based on 2D joint profiles, while the contact and tortuosity based on 3D surfaces were often overlooked. Only a few works have been made on quantifying the effect of contact area on flow behaviour (Walsh, 1981; Zimmerman et al, 1992; Zimmerman and Bodvarsson, 1996; Yeo, 2001), and mostly ignored contact area change induced by shearing and the associated impact on flow behaviour. Summarily, the quantification of fracture geometry effects on water flow in single rock joints still needs further investigation, especially when considering coupled shear-flow processes. This paper, therefore, aims to study the impacts of contact area and aperture distributions of the single rock joint on the flow behaviour. The evolutions of contact area and aperture distributions induced by shear are considered. Then, an improved model for estimating the hydraulic aperture with the mechanical aperture incorporating the above factors is developed. Finally, a series of shear and shear-flow tests are conducted on artificial joint samples and the model performance is verified by comparing against the results of experimental tests.

Nov 29, 2022

A system of decline mine entries and ore haulages has been designed for the Mt. Windarra mine. This choice was controlled by the nature of the ore- bodies, the mining method chosen and the capital cost of development re- quired for production. Mine entries are being driven 4 metres high and 5.5 metres wide and decline at 11%, to accommodate diesel haulage vehicles of 35 tonnes capacity. The.Mount Windarra haulage system and the design parameters used in its selection and design are discussed, and general design and selection parameters are proposed.

Jan 1, 1973

In the introduction to a recent paper dealing with, the relationships of magnetite and hematite in the banded iron formations or "jasper bars" of the Western Australian pre-Cambrian(17)t the author made a brief mention of these interesting rocks, of the principal series in which they occur and of a few of the rock and mineral types to be found within them.He drew attention to the essential shnilarity of these Western Australian banded iron formations to those of the pre-Cambrian of such other countries as the United States Lake Superior region, Sweden, South Russia, India, South Africa and Brazil, and gave a brief summary of his views as to the origin of the formations in Western Australia. Furthermore he stated that the banded iron formations have proved of considerable direct economic importance in the goldfields and other' regions of Western Australia, and he referred to the assistance they have provided the field geologist in geological mapping and the determination of geological structures.It is in elaboration of this last statement that the present paper has been written. In the following pages will be found some examples of the use to which the jasper bars have been put in the determination of the geological structure of critical areas in the goldfields of the State.Firstly, however, it may be as well to recapitulate the features of interest in these rocks. The true jasper bars or banded iron formations including the types jaspilite, banded hematite quartzite and banded magnetite quartzite or chert, together with their higher grade metamorphic derivatives such as banded magnetite-gruneri~ quartzites, magnetitegrunerite schists, fayalite ,and hedenbergite bearing handed magnetitegrunerite quartz rocks and' to 'a lesser extent magnetite-hypersthene grunerite quartz rocks, are abundant in the older series of the Western Australian pre-Cambrian. They are best developed in the older Greenstone or Kalgoorlie series of the goldfields districts, interbedded with metamorphosed basic lavas, tuffs and sediments. The mineralogy andpetrology of these rocks, the history of their metamorphism and their origin have been discusseq elsewhere in some detail by the author(19), (20). In one of the papers(20) it was clearly demonstrated that in the light of the true facts the old silicified shear zone theory of the origin of the jasper bars is quite untenable and that the formations undoubtedly represent sedimentary horizons as was recently pointed out by McKinstry(14).It has also been shown that banded ferruginous cherts, quartzites and cherty carbonate rocks of much lower metamorphic grade are well developed...

Jan 1, 1943

By J P. Moodie

Recent trends in flotation technology are briefly reviewed. These show that considerable development has been made as the operators, suppliers and technologists have responded to the challenges of the industry. Most of these advances have been based on empirical and phenomenological methods. There is a considerable opportunity to make further advances through a more fundamental, scientific approach. Some of this work is discussed and, although progress is being made on this front, industrial uptake has been somewhat slow. A number of specific issues facing the industry are discussed.

Jan 1, 2005

Samples weighing O·25 g are fused with 1 g potassium hydrogen sulphate, leached with 5 ml. of hydrochloric acid, and then diluted with another 5 ml. of acid. After settling, an aliquot of the clear solution is reduced with stannous chloride, and then a zinc dithiol solution is added to form a coloured tungsten complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 4 p.p.m. may be analysed at a rate of 100 determinations per man-day of 8 hr.

Jan 1, 1970

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

By R O. Laidlaw, J L. Mauk

The Coeur d'Alene mining district in northern Idaho, USA is the second largest producer of silver in the world. Mesothermal silver-lead-zinc veins occur in the metasedimentary rocks of the Belt Supergroup with five main types of associated hydrothermal alteration: 1) feldspar destruction, 2) hydrothermal bleaching, 3) carbonatisation, 4) sulfidation, and 5) silicification. Hydrothermal bleaching is characterised by hematite destruction with associated siderite and quartz veins and veinlets, coarse euhedral pyrite and magnetite. Bleached zones envelop both mineralised and barren veins and extend for metres to tens of metres into the wall rocks. Carbonatisation consists of addition of siderite, which occurs as veins, veinlets, stockwork, irregular blebs or spots, and coarsely disseminated grains, depending on the relative distance from the main vein structure. Siderite envelops nearly all mineralised veins, relates to all other alteration types and extends from several metres to tens of metres into the wall rocks. Pyrite and galena alteration dominate sulfidation and are associated with some mineralised veins. Pyrite alteration strongly correlates with siderite alteration and exists in three main forms: a) very fine-grained pyrite flooding, which can extend for metres to tens of metres into wall rocks; b) coarse-grained, euhedral pyrite, which is sporadic and associated with the redox boundary in hydrothermally bleached zones; and c) small isolated zones (6 - 15 cm) of medium-grained, subhedral to euhedral pyrite associated with pervasive siderite alteration. Where present, disseminated galena extends for metres to tens of metres into the wall rocks. Silicification is characterised by veins, veinlets, stringers, irregular patches and variable hardness in siltites and commonly appears in association with hydrothermal bleaching and siderite alteration. Although related to mineralisation, silicification is sporadic and in most places a clear envelope around mineralised veins cannot be identified.

Jan 1, 2001

By A Madera, R Watt

The Tampakan deposit is a strongly telescoped high-sulphidation-epithermal/ porphyry deposit pair which is hosted by a sequence of probable Pliocene age subaerial andesite flows. These host units lie on the western flank of a deeply dissected andesitic stratovolcano within the northernmost portion of the Sangihe Arc in southern Mindanao. The deposit was discovered by WMC geologists in 1992 and is currently undergoing resource evaluation. Preliminary resource estimations indicate a total inferred metal content of 12 million tonnes of copper metal and 16 million ounces of gold. Using a 0.2 per cent Cu cut-off grade, the deposit has a current mineral resource of approximately 2.5 billion tonnes with an estimated grade of 0.48 per cent copper. At a higher cut-off grade of 0.5 per cent Cu, the mineral resource is approximately 900 million tonnes with an estimated grade of 0.75 per cent copper. Mineralisation is open both to the west and at depth. The Tampakan district is centrally located with respect to a 100 km wide zone of left-lateral strike-slip deformation represented by the trans-Mindanao Cotabato Fault Zone. The district is transected by several WNW-striking wrench faults which represent strands of the regional Cotabato Fault Zone. High-sulphidation epithermal mineralisation within the Tampakan deposit is strongly controlled by NNE-trending faults which lie along a dilational orientation within the Pliocene stress field associated with the Cotabato strike-slip fault zone. The mineralisation is broadly hosted by a gently-dipping, tabular zone of partial to massive silicification which displays multi-phase brecciation, acid-leaching, related vuggy porosity and which is developed within a district-scale advanced-argillic and argillic lithocap exceeding 90 km 2 in area. High-sulphidation epithermal mineralisation is associated with a silica-pyrophyllite-dickite-alunite-diaspore¦sericite alteration assemblage which is transitional downward to sericite-chlorite alteration and relict potassic biotite-chlorite-magnetite-anhydrite alteration associated with pervasively developed but weakly mineralised porphyry quartz stockwork veins. The high-sulphidation mineralisation is dominated by disseminated, vein and vug-filling enargite-bornite-digenite-chalcocite-covellite ¦ molybdenite which has overprinted an earlier phase of porphyry copper stockwork veins associated with high-level porphyritic hornblende diorite stocks. The distribution of high-sulphidation alteration and mineralisation reflects strong stratigraphic and structural controls. The high-sulphidation mineralisation covers a surface area of approximately 1.6 km by 2.0 km and forms a tabular, flat-lying to gently-dipping body between 200 and 500 metres thick. It is intersected at RL-1200 m ASL (at surface) in the northern portion of the deposit and extends down to RL-600 m ASL at the southern end. The deposit has been diamond-drill tested to a depth of 400 - 500 metres where low-grade chalcopyrite-bornite-pyrite mineralisation is hosted by pervasive quartz stockwork veins. This deep-level mineralisation represents the outer portion of a porphyry Cu system hosted by both andesite flows and the uppermost portions of high-level hornblende diorite stocks. Deep drilling to test for higher tenor porphyry Cu mineralisation is planned.

Jan 1, 1999

By E Vargas, A Egana, M Alarcon, X Emery, A Barberan, A Lopez, N Morales, C Friedrich

"As the cost in time and money of data from sensors and small-scale tests has reduced, additional challenges have arisen. Although many mine data sets are not big relative to those in other disciplines, they are complex in other ways, and becoming too large to manage efficiently on personal computers. In order to take advantage of the opportunity offered by increased data, a diverse team from Universidad de Chile and CSIRO Mineral Resources has developed a virtual geometallurgical laboratory to support the computational requirements linking data acquisition with data-driven business decisions. A particular focus to date has been the development of user-guided workflow ensembles to enable comparison between plausible geometallurgical hypotheses.A case study has been undertaken using publicly available data from the Rocklea Dome iron deposit in Western Australia. A hypothetical mining schedule was produced from geochemical and hyperspectral drill core/chips data via the following steps: data preprocessing, exploratory data analysis, geochemical interpolation, block modelling, ultimate open pit design and scheduling. The key outcome of this study was the integration of workflow stages through new plug-in methods or modification of existing software. Outcomes from this study will be described in the paper in terms of geological and metallurgical data quality, analytical software support and ongoing computing infrastructure requirements.CITATION:Lopez, A, Barberan, A, Alarcon, M, Vargas, E, Ortiz, J, Morales, N, Emery, X, Egana, A, McFarlane, A and Friedrich, C, 2016. Progress towards Data-driven Mine Planning via a Virtual Geometallurgical Laboratory, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A J. Cornah

"The mine geologist’s role in classifying ore from waste during grade control represents a critical link in the mining value chain. Any improvement in the ore/waste selection success rate (thus reduction in misclassification) which can be delivered by the mine geologist represents a value proposition. Improvement achieved without additional operating cost (for example extra drilling and sampling) will directly and immediately add value to the mining operation and therefore clearly must be pursued. Such improvement may be leveraged from existing resource drilling data which are typically less numerous but better quality than the grade control data. They are usually excluded from grade control estimates (termed the ‘base case’ approach here) because of the differences in quality.Various specialised geostatistical tools are available to account for differences in precision and accuracy between data sources during spatial estimation. This paper uses a conditional simulation (CS) case study to assess the benefit of integrating resource data into grade control estimates through ordinary kriging (OK) of pooled data sets, cokriging (CK), and ordinary kriging with variance of measurement error (OKVME) when the grade control data are:unbiased but increasingly imprecisebiased and increasingly imprecise. The premise assumed is that the resource data are unbiased and precise.The paper demonstrates that, if appropriately handled, resource data may be used to improve grade control estimates and thus improve ore/waste selection success without additional operating cost. Where grade control data are imprecise but unbiased it is recommended to integrate resource data using OKVME. This re-appropriates kriging weights from less precise to more precise data locations and improves the grade control estimation precision compared to the base case; it consequently provides an improvement in the grade control selection success rate. If grade control data are associated with significant bias, integration through CK is recommended as the biased data are zero sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case and consequently improvement in the ore/waste selection success rate.CITATION:Cornah, A J, 2014. Incremental improvement of grade control models using resource data, in Proceedings Ninth International Mining Geology Conference 2014 , pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By S Wangchai, D B. Hastie, P W. Wypych, A P. Grima

Industries that handle and process ‘dusty’ ores are facing increasingly difficult challenges to ensure sustainable operation and development. Most existing dust-control measures treat only the symptoms of dust generation and do not deal with the root cause/s of the problem. Many of these methods are also relatively inefficient in terms of controlling dust emissions. This paper summarises the various existing options available for dust control and some of their features, advantages and disadvantages. It then describes some of the new technologies that are being researched, developed and employed to minimise dust emissions by addressing dustability or dustiness and the dust generation mechanisms found in industry. Recent research results and case studies are presented to demonstrate some interesting findings obtained from this work. With improved understanding and modelling of dust generation mechanisms and bulk material dustiness, it is possible to achieve a step-change improvement in the design, troubleshooting and application of more efficient dust-control technologies.CITATION:Wypych, P W, Hastie, D B, Wangchai, S and Grima, A P, 2015. Research and application of new dust control technologies for the iron ore industry, in Proceedings Iron Ore 2015, pp 529–536 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Bandopadhyay

The seasonal fluctuations of the dust content in Arctic mine environments and the environmental variables affecting the intensity of dust production are qualitatively well known, but quantitative models that allow simulation and prediction of dust generation and the effects of engineering control of thermal regime on the mine environment are still non-existent. In Arctic mines, the migration of moisture in the surrounding rock mass releases fine dust by freeing it from the ice matrix allowing it to escape into mine airway. The migration of moisture is the direct cause for the production of mine dust and heat is the primary driving force. This paper examins the heat and moisture exchange between the ventilation air and the surrounding rock mass in frozen ground, placer mines in the Arctic. Based on the simulated results of a coupled heat and mass transfer problem with phase change, methods of dust control have been identified for mines in the Arctic.

Jan 1, 2005

How often does one hear that a recent feasibility study was not a success? Alternatively, when scope of the feasibility study was sent out to tender there was a large discrepancy in tendered prices. If the tendered prices were to be compared to the consumer market, for instance the purchase of a car, where the concept is transport in a controlled and safe manner, prices vary by large factors, but then so do the specifications. In the case of a feasibility study, prices should be within a tighter margin as the tenderers are all quoting against the same concept and specification. Why do these discrepancies occur? Price discrepancies will in every likelihood be attributed to two main factors; one, the perceived amount of work and two, the ability of the bidder to carry the risk associated with the feasibility study. It is, therefore, important that the scoping of the feasibility study covers the detailed requirements as clearly as possible stating what level of accuracy is required. The feasibility study is one of the first activities in the life of a project. The study, like the project it is investigating, is subject to the constraints of time, cost and quality. Its primary objectives are to demonstrate the viability of a project within the outlined scope and constraints.

Jan 1, 1998