Search Documents

By Newell R

The situation in which a gas stream flows through a bed of solids is found in many extractive metallurgy operations. Examples include blast furnace smelting, sintering and pellet firing. In such cases the resistance of the bed to fluid flow and heat transfer is of major significance to the operation of the process. This depends on the structure of the bed, which in turn is influenced by the manner in which the materials are charged to the bed. In this work, packed beds of hematite pellets of two different sizes were prepared in which the pellets were charged as a uniform mixture and in layers. The porosity, flow resistance and heat front velocity were measured and compared for the different bed configurations. For layered beds, the overall porosity and heat front velocity increased while the flow resistance decreased when compared with the values obtained for the uniform mixture. The size of the layers also had an effect on flow Properties.

Jan 1, 1991

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

By Nairin J. D, Hayes P. C

Detailed studies of the microstructures and compositions of zinc and lead blast furnace sinters have been undertaken. An analysis of the results obtained has indicated that in many cases the microstructures of these complex materials can be explained by the solidification of melts from pseudo-ternary phase systems. Further laboratory studies have been carried out to more accurately determine the extent of primary phase fields and the liquidus temperatures in the appropriate binary and ternary systems. This approach shows considerable promise in simplifying the descriptions of slag systems used in oxidising and reduction smelting processes for lead and zinc recovery.

Jan 1, 1992

A relationship is predicted between oxidic nickel in slag, oxygen in matte and Ni/Fe ratio in matte after the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters. Oxidic nickel in slag is found to increase with increase in oxygen content of matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1979

Confirmation of significant mineable reserves of high grade silver ore at Elura Mine has led to the development of a high cost, high recovery mining system. At the contact of oxidised and sulphide ores lies a supergene zone of enrichment which has provided a contrast, not formerly imagined, to Elura's primary development and stoping operations. Because of the soft nature of the ore, intense ground support practice has been combined with a panel cut and fill continuous mining system to extract a reserve of small, but most valuable Proportions.

Jan 1, 1988

By Potter DJ, Firkin GR

The Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at its Cockle Creek zinc-lead smelter was recently equipped with tuyeres angled at 25 degrees instead of the usual 10 degrees. This change was prompted by the results of model studies undertaken by tha Research Department of Imperial Smelting Processes Limited, at Avonmouth in the United Kingdom, and by the favourable results of operating trials on the Cockle Creek furnace using bent-tip tuyeres to simulate 25 degree inclination. The use of 25 degree angle tuyeres has made it possible to operate with lower zinc values in discard slag and has improved hearth stability over a wider range of sinter quality and composition.

Jan 1, 1981

By Fuller T

This paper introduces the technology used in laser surveying systems, and the development of a reflectorless one-man total station. These systems are being used for applications such as blast pattern surveys, face profiling, muckpile surveys and the general survey of inaccessible areas. Black Diamond Solutions is continuing to assess new technology and develop integrated systems for applications in the mining industry.

Jan 1, 1995

By Baafi EY

Geostatistics is now widely used in the mining industry in the estimation of ore reserves and terms like kriging, variogram and estimation variance are becoming well known. Ordinary Kriging (OK) has been found by some practioners to be a superior tool compared with other ore reserve estimators. However, kriging hasn't been the ultimate solution to difficulties which may arise in ore reserve estimation. Several additional geostatistical techniques have been recently developed for more efficient ore reserve estimation in some deposits, especially gold and other precious metals. These include indicator kriging and probability kriging which are useful tools to work with in a selective mining operation.

Jan 1, 1987

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

By Wu Y. H, Lu J. P

Slope stability has now become a practical tool in the design and oper- ation of open pits. The stability of rock slope depends on many factors, including not only structural geology, the existence of weak layers, ground- water, blasting and weathering, but also the virgin stress field. This paper presents an application of a numerical method to investigate the effect of the virgin stress on slope stability. The finite element method is employed to simulate the excavation of open pits. Redistributed stress fields in the slope of open pit are computed for several different virgin stress fields. Based on the redistributed stress fields, the shear force which tends to produce sliding of a rock mass and the frictional resistance to sliding are evaluated. The possibility of potential failure is assessed by the limit equilibrium method. The combination of the finite element method with the equilibrium method provides a powerful analytical tool for slope stability. The significant effect of virgin stress on the stability of slopes is shown by studying a typical case.

Jan 1, 1989

By D Moy, T Carter

This paper outlines the feasibility assessment conducted to explore the possibility of constructing two submarine water supply pipelines beneath the Ma Wan Channel in Hong Kong using either horizontal directional drilling or tunnelling. The Ma Wan Channel is a major shipping channel in the Northwest New Territories, which separates Ma Wan Island from the mainland. The challenges faced by the projectÆs designers included space limitations on either side of the channel, marine department restrictions on construction activity within the channel and selection of a suitable crossing alignment and profile given the channelÆs depth, irregular sea floor topography and complex geology. The existing geological information indicated the proposed alignment would cross granitic and volcanic formations, which would likely be faulted. The primary concerns with horizontal directional drilling were:the length, diameter and depth of the crossing were at the limit of precedent experience in rock; the lack of available space at both the entry and exit sites; and whether the technique would be flexible enough to cope with the anticipated range of ground conditions. The primary concerns for tunnelling were: the possibility of encountering large inflows of high pressure groundwater; andthe possibility of encountering disturbed ground within the fault zones which could flow if not properly treated. As a means to evaluate and mitigate these technical risks for both construction options, a directionally drilled pilot hole was used to investigate the ground conditions along the proposed pipeline alignment. The pilot hole results indicated that either directional drilling or a closed face TBM drive were technically feasible crossing options at a crossing depth of 80 m. The results also indicated that either an open face TBM or a drill blast drive would need to be constructed at much greater depth because of the presence of highly permeable, disturbed ground in mid-channel at this crossing elevation.

Jan 1, 1999

By Finlayson E, Hilyard D, Francis G

Papua New Guinea's mainland is dominated by a foreland thrust belt, which can be divided into two zones. The "body" zone is floored by Palaeozoic granites and metamorphics of the Fly Platform (Tasman Orogen). Underlying the "tail" zone is Papuan Plateau, rifted from the Tasman Orogen during Coral Sea spreading, and believed to underlie the Papuan Peninsula and Papuan Islands region (D'Entrecasteaux, Woodlark, Misima, Sudest, and Rossel Islands). Thrusting began in the Miocene and continues today in the crust below the "body" zone. The youngest known thrusted rocks in the "tail" zone are Pliocene in age. Recognition of foreland thrusting has major implications for petroleum prospectivity of the Papuan and North New Guinea Basins, mineral exploration prospectivity, and geological terrane identification in PNG.

Jan 1, 1987

General Gold was discovered in quartz veins at Wiluna in 1896, and the first lode was discovered in 1904. Since 1896, some 2.5 million ounces of gold have been produced from the Wiluna area. The mining operations at Wiluna are 100 per cent owned by Wiluna Gold Pty Ltd, a wholly owned subsidiary of Wiluna Mines Ltd. Oxide and sulphide gold ore is extracted by conventional open pit mining techniques, and ran-of-mine ore is processed through two separate circuits. The oxide circuit has a capacity to treat 600 0(X) tonnes per annum and the sulphide circuit has a capacity to treat 400 (XX) tonnes per annum. Additional gold is won by dump leaching sub-grade oxidised ore and by retreating of primary ore flotation tailings from previous operations. Testwork carried out in 1990 indicated the viability of leaching dumps of run-of-mine oxide ore, and in June 1991 Signet Engineering of Perth, WA, was awarded an EPCM contract to construct a nominal 2.5 million tonne dump leach facility, for a total construction estimate of 51.75 million.

Jan 1, 1994

Methane is present in varying degrees in nearly all underground coal mining operations. At mixtures with air near 5-15% it is explosive and consequently since it is not usual for these levels of contamination to be reached in the general body of a mine ventilation system it is not unusual to experience it in specific places. On longwall faces the most used power loader is the shearer machine and because of its general shape, situation and operation it is likely that all the factors which are required to cause a frictional ignition can be present. This paper makes a general appreciation of the causes of these ignitions and methods which are and have been used to control these situations on and around these machines.

Jan 1, 1981

By Takeuchi T, Matsugaki K

We have developed a new shotcreting which is suitable for the primary support of TBM tun- nelling in soft rock. This spraying compound is made from cement, a special accelerating agent and glass fiber. It can be sprayed on to a rock surface using a specially designed gun similar to paint-spraying equipment. Some of the characteristics of this method are as follows: 1) If spraying is done keeping the distance between the gun and the rock surface be- tween 0.2 and 3.0 m, the rebound losses are small and there is little dust. 2) This method can be used on excavated rock surfaces under inflowing water conditions of up to 10 i/m2òmin. 3) After 1 day the compressive strengthes of the sprayed material is greater than 250 kgf/cm2.

Jan 1, 1987

By McGuckin P. H

The Cadjebut orebody is a MississippiValleyType (MVT) zinc-lead deposit, and is located approximately 80 km southeast of Fitzroy Crossing in the Kimberley region of Western Australia. It is one of five zinc rich orebodies discovered by BHP Minerals in the region.The participation in the Cadjebut Joint Venture is BHP Minerals limited (Manager), 58 per cent and Billiton Australia Limited, 42 per cent.The mineralisation is contained in gently dipping dolomitised limestone sediments (part of the Lennard Shelf carbonate sequence) with an orebody width of between 60 and 120 m and a strike length of approximately 3 km. The deposit consists of two thin, stratabound shallow dipping orebodies, one overlying the other, to provide discrete but not independent mining areas. The orebody contains approximately 2.1 million tonnes of recoverable ore at an approximate grade of 12 per cent zinc and four per cent Lead.

Jan 1, 1992

By Bourke J. H, Ashcroft T. B

Many changes have occurred in the world market for manganese over the last five years. Among these, the emergence of divided steel processes for the hot metal refining of pig iron is affecting the use of both ferruginous manganese ore and ferro manganese, at this stage particularly in the Japanese steel industry. Subsequent demand for higher quality manganese materials is promoting the use of thermally beneficiated products such as sinter. In addition, many processes are being developed for the direct smelting of fine manganese ores, of which plasma technology is the most advanced. Cost pressures and product quality requirements are encouraging pre- viously self sufficient countries such as The People's Republic of China and the USSR to import high grade manganese ores to supplement indigenous lower quality supplies. At the same time, Brazil has been provided with the impetus to convert its substantial reserves of ore to value added products.

Jan 1, 1988

This paper examines the cost and economic consequences of varying a number of key factors in the course of developing and operating new underground longwall coal mines with both shallow and deep cover in New South Wales. The economics of the project are assessed for the first 20 years of mine life using the discounted cash flow method with produc- tion and selling price being determined to provide break even costs for a range of minimum rates of return.

Jan 1, 1988

By Thornton D, Firth B, Kojovic T, Brien G, O&apos

Coal fragmentation is a function of coal type and mining process. Each unit step in the mining, handling and crushing chain of coal imparts energy to the material and impacts on size degradation and consequent mineral matter liberation and pla

Jan 1, 1998

The rapid industrialisation of the world was driven by an improved ability to utilise chemical energy. Unfortunately harnessing explosive energy did not come cheaply given the hundreds of lost lives. However, the modem explosives industry has made significant technological achievements, for explosives are now considered to be both safe and extremely effective. Upon closer inspection, it would appear the key to this achievement has been the development of initiation systems. While the focus may have been originally on safety, modem developments have concentrated upon harnessing the benefits of initiation control. Before attempting to gaze into the future, it is worth reviewing some of the significant advances that have occurred.

Jan 1, 1990