Search Documents

A method is presented for calculating the number of cycles of stress to failure of a drill rod from operating variables; a mathematical analysis by Cooper of the stresses present in drill steels is applied to the forged collar, i1i-in. hexagonal hollow drill steel in common use in Australia; and an estimation is made of the dry fatigue limits at various points along a drill rod.It is shown that these calculations predict failure at a 'point where failure rarely occurs, and do not predict that failure should occur where it does in practice. The reasons for this anomaly lie in the neglect of bending stresses in the stress calculations, and in failuredue to corrosion fatigue at a preferred section rather than to simpler fatigue under non-corrosive conditions.INTRODUCTIONIt has long been recognized that failure of metal sections by fatigue is influenced both by the number of cycles of stress imparted to the section (N) and by the magnitude of this cyclic stress (8). In this paper, both Nand Shave been calculated for rods which have failed in service, and whose operating history is known. While the calculation of the number of cycles to failure is·simple, the calculation of stress is more complex. The results of stress caIculations predict that failure should occur only hi short rods, and then preferentially at the tip end rather than the shank end.However, in actual fatigue failures of steel rock drill rods, approximately 75 per cent. of such failures are close to the shank end, and failures near the tip end are rare.The usual explanation given for this high incidence of shank-end failures is that at the point of failure there exists, in forged collar steels of the type common in Australia "hardness valley" or. "m'etallurgical notch". This narrow valley in hardness is a weakness, and failure is expected to occur at the weakest point at the bottom of...

Jan 1, 1955

By A Gerdes, H BrStz, E GSbler, D Davis, F Henjes-Kunst, S Dewaele, T Graupner, T Oberthnr, M Sitnikova

Following the United Nations initiative to fingerprint the origin of conflict materials, the German Federal Ministry for Economic Cooperation and Development has decided to fund a pilot study on coltan ores. Since 2006, our working group has been investigating columbite- tantalite (coltan) mineralisation, especially in Africa, also within the wider framework of establishing certified trade chains. More than 300 samples were obtained from the worldÆs major coltan producing areas. Special attention is, however, directed to samples and concentrates from Ta-Nb-Sn provinces in Africa: Democratic Republic of the Congo, Rwanda, Mozambique, Ethiopia and Namibia. Using state of the art analytical tools, we investigate mineralogical and chemical parameters obtained from columbite-tantalite ores and concentrates in order to distinguish between ore provinces, likely even down to the deposit scale. Methods employed include fully automated electron microscopy (mineral liberation analysis), electron microprobe analysis (major and minor elements), laser ablation plasma-source mass spectrometry (trace elements and U-Pb dating), X-ray fluorescence spectroscopy (bulk major and trace elements), X-ray diffraction analysis (mineralogy and structure) and thermal-ionisation mass-spectrometry (U-Pb dating). Major and trace element concentration patterns, mineral assemblages in the ore concentrates, and zoning characteristics in the different pegmatites from Africa distinctly differ from each other. Furthermore, the following age populations are evident:Archaean (>2.6 Ga);Palaeoproterozoic (1.9 - 2.1 Ga);early Neoproterozoic (æKibaranÆ; 0.98 - 0.93 Ga); andlate Neoproterozoic to early Palaeozoic (ca 0.5 Ga). Currently, we focus on the resolution of the fingerprinting system from region via ore province down to deposit scale. Our preliminary analytical results indicate that a certification scheme including fingerprinting of sources of coltan ores is feasible.

Jan 1, 2008

Average annual growth in consumption of primary energy in Australia over the past 10 years has been 5·5 per cent compared to a world average of 4·1 per cent.Over the next 10 years growth rate is expected to increase to 6 per cent per annum due largely to the rapid development in the mineral processing industry.By the end of the 19705 natural gas is expected to supply more than 9 per cent of Australia's primary energy market. Coal will supply 40 per cent and petroleum products 47 per cent. Nuclear energy will make its appearance but will make only a small contribution in the period.Australia has adequate reserves of natural gas and coal to supply its needs in the 1970s and beyond. However the newly developed reserves of crude oil, while supplying 60-70 per cent of requirements in the initialyears, will need regular and sizable additions if they are to keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated that new discoveries will need to approximate ten times the volume of recoverable reserves found in Australia to date.

Jan 1, 1971

By B Davis, M Wallace, J Stewart, C F Burrett, J B. Cannell

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Sepon district in Lao PDR contains 1.8 Mt of JORC (2012) compliant contained Cu resources in addition to >4.5 Moz of Carlin-like Au in a Palaeozoic sedimentary package. The Cu deposits are proximal to an EW lineament of Permian rhyodacite porphyry (RDP) intrusive centres that are characterised by intense barren quartz stockworks. The Khanong deposit (42 Mt at 3.0 per cent Cu mineral inventory) is a carbonate replacement intermediate sulfidation deposit verging on a high sulfidation environment, where abundant pyrite, copper sulfides (chalcopyrite, bornite, trace enargite), copper sulfosalts (including tennantite – tetrahedrite, colusite), and base metal sulfides (sphalerite and galena) have replaced low dipping dolomite and limestone layers, forming a manto-style orebody fed by steep dipping intensely silica-pyrite altered structures. The Thengkham deposits (54 Mt at 1.5 per cent Cu) are composed of prograde skarns (garnet, clinopyroxene) and mineralised retrograde skarns (chlorite, magnetite, hematite, epidote, sericite, talc, serpentine, carbonates, sulfides) which are irregularly and semi-continuously distributed around an elongate 4 km long intrusive centre. Thengkham and Khanong have been strongly supergene enriched, forming secondary chalcocite breccias and exotic malachite zones.The Carlin-like Au deposits display a range of stratigraphic and structural controls and lie outboard of the Cu deposits. Similar structural controls, alteration assemblages and trace mineralogies suggest that gold and copper mineralisation are temporally and genetically related. It is hypothesised that the differences in style of Cu and Au deposits across the Sepon district are related primarily to palaeodepth and proximity to the intrusive centres.CITATION:Cannell, J B, Stewart, J, Williams, P, Wallace, M, Burrett, C F and Davis, B, 2015. The Sepon copper deposits (Laos) and their relation to Carlin-like gold mineralisation, in Proceedings PACRIM 2015 Congress, pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M A. Tuck

Atmospheric air on a moisture free volume basis consists of approximately 21 per cent oxygen. The current minimum threshold for oxygen in Australia is 19.5 per cent. Atmospheric air generally will also contain water vapour and will also pick up further moisture as it flows around a mine ventilation network. This paper details the results of a study to determine how much oxygen depletion can occur due to the sole impact of increasing the moisture content of air and the potential impacts of this on ventilation system design. The study shows that the moisture content can have a significant impact on the oxygen concentration in mine air. The main factors controlling the impact are the barometric pressure, dry bulb temperature and relative humidity of the air.CITATION:Tuck, M A, 2015. What is the oxygen depletion potential of ?water vapour?, in Proceedings The Australian Mine Ventilation Conference, pp 173–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Coal washing practice can be improved not only by critical examination of the plant being operated but also by studying plants operated in other areas. The developments at the Australian Iron & Steel Pty. Ltd. plants are discussed in relation to experiences there as well as developments which have taken place in Queensland in recent years. Early A.I.S. problems involved small coal cleaning in heavy medium cyclones and flotation. A proposed future plant flowsheet for A.I.S. is considered in the light of these experiences. Reference is made to plants operated by the Thiess, Peabody, Mitsui Coal Company Pty. Ltd. at Moura and the Utah Development Company's plants at Blackwater and Goonyella in the development of coal washing prac- tice in Australia.

Jan 1, 1975

The paper describes developments since 1959 in major excavators to meet the demand for higher outputs of overburden and coal under less favourable batter conditions than used hitherto in the coal deposits of the Latrobe Valley. Particular reference is made to investigations of designs of bucket wheel head configurations for the digging of these flat batters on high faces, and examples are given of the wide use of models inthese studies. An explanation is given of how solution of these problems and surface conditions unfavourable for wheeled transport confirmed selection of the long boom rather than the compact type of bucket wheel excavator for the Latrobe Valley applications.The past decade has seen advances in the manufacture in Australia of components for excavators and similar machines. The history of Australian manufacture of components for major brown coal excavators is traced;and reference is made to study and application of Australian and overseas (mainly German) codes and practices in the design and construction of machines made partly here and partly in Germany.A section of the paper deals with advances in electrical engineering for large excavators in Australia and its interdependence with mechanical design and construction.Finally, as an example of the versatility of the bucket wheel excavator, a description is given of a recent application for the mining of mineral sands in northern N.S.W.

Jan 1, 1971

By M Iglesias-Martínez

The potential for iron ore in the Central African Archean belts has received much less attention by comparison to their equivalents in other cratonic regions of West Africa, South Africa, Australia and Brazil. Historically, iron ore is known to occur in South Cameroon and North Gabon with significant iron ore deposits (eg Mbalam in Cameroon, Avima in the Republic of Congo, Minkébé, Bélinga and Boka-boka in Gabon), having been the subject of geological exploration programs carried out by government institutions and exploration companies. Although the presence of strong aeromagnetic anomalies, undeniably related to the presence of greenstone belt formations, has been recognised, this study is the first attempt to assess the potential of banded iron formations (BIF) in the Northern part of the Gabonese Republic in the region between Minvoul and Minkébé (>10.000 km2). Deep lateritic weathering, inaccessible equatorial rain forest and high operational costs are some of the reasons why only limited exploration has been undertaken in the area. This work aims to improve the geological knowledge and to highlight the potential for iron ore of the eastern margin of the Ntem Complex units dated between 3.3–2.7 Ga. Field work showed a series of mafic rocks (amphibolite, anorthosite and gabbro), schist and BIF (described as itabirites in neighbouring areas). Samples from Minvoul BIF showed an extensive and deep weathering to powdery hematite revealing the presence, in thin sections, of iron oxides including magnetite, hematite and martite, primary and secondary quartz, garnet, hornblende, anthophyllite, cummingtonite and epidote. Mineral assemblages and coarse grain size suggest a metamorphic grade ranging from medium to upper amphibolite facies. The existence of known economic iron ore deposits in neighbouring regions combined with an extensive weathering enrichment process are promising factors for potential iron ore discovery in this remote area.

Sep 18, 2023

The metals titanium and zirconium and their alloys occupy individually unique positions in the catalogue of metallic materials available for engineering applications. Because of the uniqueness of their usage in the aerospace industry, in the case of titanium, and in the nuclear industry, in the case of zirconium, the except- ional resistance of both the metals to the majority of corrosive media is often overlooked. The cost factor in the application of these more exotic metals has, in the past, been a major considerat- ion in the rejection of titanium and zirconium as constructional materials in areas of usage where their superior corrosion resistance strongly favoured them over more conventional metals and alloys. The cost differential, vis-a-vis austenitic stainless steels, for example, is not a trifling matter, being of the order of 6 : 1, when compared on a weight basis. However, if one considers the cost, for, say, sheet product on an area basis, the ratio is redgced to approximately 3.4:1. If one also takes into account the enhanced performance of the more expensive material and the sub- sequent increase in service life and decrease in plant down-time, the economics of the usage of materials such as titanium becomes much more attractive and, indeed, highly competitive,

Jan 1, 1969

By Whiten WJ, Narayanan S

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. This analysis reveals that the relative power inefficiency of large ball mills is due to inefficient grinding of coarse (plus 4 mm) particles in these mills. A qualitative physical hypothesis is proposed to explain this behaviour. The results of the analysis can be used to scale up ball mill behaviour, using the mathematical models and techniques developed. A simpler ball mill scale-up procedure is also proposed, and its limitations stated. Laboratory experiments are being conducted to determine the average size distributions of single particles of different ores after breaKage. These experiments can distinguish between the different ores, and it is hoped to use their results to model and predict the grinding of different ores in ball Mills.

Jan 1, 1978

Attention is given to three possible alternative structures namely corporate joint venture, partnership joint venture and unincorporated joint venture. A corporate joint venture involves the formation of a separate and distinct legal entity with limited liability. The shareholders of the Company will be the members of the consortium. A partnership joint venture involves the members of the consortium joining a formal partnership. The partners will conduct the business in common with each other and will share the profits and losses of the project activities. The partners will be jointly and severally liable. An unincorporated joint venture is distinct from a partnership. The members of the venture will not be jointly and severally liable. Taxation and accounting aspects are examined and an outline provided of a typical joint venture agreement. The two main advantages of an unincorporated joint venture are considered to be a favourable treatment for income tax purposes and a greater degree of flexibility when compared with the corporate joint venture and the partnership joint venture.

Jan 1, 1983

By Jones M

The concept of precise, accurate timing with Electronic Delay Detonators (EDDs) was first seriously addressed in the mid-1980s and much was made of the cheapness and profusion of digital watches in terms of the likelihood of EDDs also being cheap and easy to produce. Ten years later, with every major explosives company and many electronics groups having instituted projects to capitalise on the promise of these devices, production devices are still to come into general use. In South Africa, Expert Explosives units have been used in most applications during proving trials and more recently for production blasting in underground ring stoping and open cast coal. The outcome has been valuable learning both as to the benefits and technical requirements for electronic delay blasting, and especially, safety aspects. Examples are shown of production blasts which utilised the power of EDDs. It is evident that it is not delay accuracy alone which determines the value of these systems, but the whole robustness, flexibility and ease of delay allocation when harnessing blast engineering knowledge. Muckpile movement and shape, fragmentation and vibration frequencies have shown to be greatly influenced by designs which can be implemented no other way. The flexibility of a system and the power of the software controlling it are crucial in capitalising on blasting potential, which lies in integrating control of blast timing with other developing electronic Technologies.

Jan 1, 1995

Blast furnace slags which fall into the quaternary system SiO2 - A1203 - MgO - CaO have latent hydraulic properties which depend on the degree of vitrification. When the oxides com- bine to form Calcium Silicate Hydrates and other products of hydration the bonds between elements are at a lower energy level than those which exist in the glassy state. Transition from the glassy state to the crystalline state is thermo- dynamically favoured and, in the context of this paper, such slags possess internal energy. Manufacture of Portland cement is respon- sible for about 3.6 per cent of total industrial energy consumption in Canada. Pyroprocessing accounts for about 83 per cent of this figure or 3 per cent of the total. The processing of blast furnace slag to a condition in which it can be used as a partial substitute for Portland cement requires no pyroprocessing and, on average, only about 11 per cent of the energy needed for Portland cement. In North America the benefits of slag as a cementitious materials have been obscured by other considerations, the most important being commercial strategy. This situation has under- gone radical change as a result of the rising cost of energy, and government pressures to conserve energy.

Jan 1, 1979

By R van Berkel, J Lay, D van Beers

The development of regional resource synergies in intensive areas with concentrations of minerals processing industries provides a significant avenue towards sustainable resource processing. Gladstone (Queensland) and Kwinana (Western Australia) are two of AustraliaÆs major heavy industrial areas. There are a number of successful regional synergies in both areas. In addition to the existing regional synergies in both areas, more potential synergy opportunities appear to exist which, upon implementation, could benefit industry, the environment and the community. To further enhance the development of such potential regional synergies, the Centre for Sustainable Resource Processing (http://www.csrp.com.au) commissioned research projects to facilitate the identification of potential synergies and assist with their implementation in both regions. This paper presents a selection of specific examples from both regions to illustrate the sustainability benefits from regional synergy developments. Although the composition of industries in the Gladstone and Kwinana regions is different both in terms of geography and industry diversity, similarities in synergy developments for both regions are apparent. Consequently, the examples discussed in this paper are organised around the key themes of water, energy and inorganic by-products. Comparison on a theme basis highlights success factors of successful synergies and demonstrates the range of benefits resulting from their implementation.

Jan 1, 2006

The main features and recent developments in the processes of benefication and extractive treatments of tin ores are reviewed. The need for development of processes to recover fine tin, tin from low-grade complex ores and from hard rock resources is indicated. The progress in understanding of slag-metal interactions and developments of fuming processes on industrial scale is delineated. the processes and prospects of hydrometallurgical and chlorination methods are briefly indicated.

Jan 1, 1992

GENTLEMEN, I have to thank you very much for the honour you have conferred upon me by electing me President of the Institute for this year. On behalf of resident members, I have to offer the visitors a very cordial welcome to Mount Morgan, and to tell them that all arrangements have been made to enable them to inspect the mine and works at their own convenience, and to supply them with any particulars they may need.It is very pleasing indeed to see such a large gathering, especially on account of the long journeys many have undertaken in order to be present. The first congress in Queensland, about eleven years ago, was attended by a comparatively small number of members, and a rather long time has been allowed to pass in consequence. The large attendance at this meeting encourages the holding of meetings in Queensland more frequently. Owing to the long distances, and the number of mining centres in Australia and New Zealand, we cannot expect to meet oftener than once in six or seven years in...

Jan 1, 1911

Nauru Phosphate, which is one of the world's highest grade deposits discovered to date, contributed in 1969, 2.2 million tons of the total world production of 77.7 million tons. Phosphate production, which is the major source of revenue for the island nation, is carried out by the Nauru Phosphate Corporation, headed by a Government appointed Board of Directors. The complete mining operation, including ship loading techniques, is discussed along with proposals at present being investigated to upgrade the Quality of the product.

Jan 1, 1971

Cyanide-extractable gold is far more meaningful in the definition of ore, and control of extraction, than fire- assayable or aqua regia digestible gold. The use of cyanide- extractable gold addresses the significant problems of over- as well as under-assaying by fire and aqua regia digests. The problems of conventional control or diagnostic cyanidation extractions: lengthy extraction, and masking by pregrobbing in cyanidation extractions for assay purposes; are surmounted with a novel activator - Leach WELL. Full extraction of liberated gold, insignificantly affected by preg-robbers, can now be achieved within 30 minutes. This can assist in reducing common gold losses presently often hidden by inappropriate mine call factors, and/or high grade cut values. This paper includes a discussion of fundamental mechanisms of cyanidation, preg- and assay-robbing, which underlie the phenomena Involved.

Jan 1, 1992

The exposed high face of Kerr's Quarry has dominated the township of Ferntree Gully for half a century. The near perpendicular face of bare dacite rock is a crumbling scar in an area of significant natural beauty. Apart from being unsightly, the face is a hazard for any person who approaches too close to its base or to the top edge. The height and the precipitous nature of this man made wall of rock is hazardous indeed. (fig. 1) The rock face is on the municipal boundary between the Shire of Sherbrooke and the City of Knox. This boundary was drawn when partition of the Shire of Ferntree Gully took place. There are many advantages in benching back the wall of the quarry but to do so the operation, located in Knox would need to extend into Sherbrooke. There are planning difficulties involved in such a manoeuvre, but during 1972, at a meeting of Cabinet Ministers, it was agreed that the matter be resolved.

Jan 1, 1976

By Griffiths L, Marshall P

fhis paper describes investigations into drainage of gas from the solid to control outbursts. Initial studies conducted on drainage of shear zones showed that, given enough time, these can be successfully drained. Once drained, they can be intersected and driven through without any activity of outbursts. The results of programme of investigations to determine parameters for drainage from the solid show that gas flow rates from the Bulli Seam on the average are about 2 litres/min/metre length of borehole. But when shear zones are intersected, the flow rates could be as high as 8 litres/min/ metre length of hole. Shear zones can be picked up from pressure measurements 50 - 60 m away and this could give sufficient time to drill through these zones and drain them in advance. Systematic drainage of Bulli Seam at West Cliff Colliery could eliminate or reduce frequency of outbursts considerably. At present drainage holes are being drilled systematically in the seam, with drainage installations on the surface. Gas purity of 80% methane is being delivered at the surface plant.

Jan 1, 1980