Search Documents

This paper summarises the current status of the mining sector in Poland in terms of vertical transport system safety. Selected results of research programs conducted at the AGH-UST relating to mine hoist system safety are reviewed. The conclusions support the notion that the costs of vertical transport systems can be reduced, while at the same time maintaining the required safety and reliability levels. Novel solutions: movable fender beams HWR, linings modar« and the integrated shock absorbers PHH for conveyance guiding systems fully confirm this hypothesis.

Jan 1, 2005

By G Balog, T Ormerod, D Sidea

Carrapateena is a copper-gold sub level caving operation located in the Gawler Craton, South Australia. One of Australia’s largest undeveloped copper deposits, the project will be a 4.25 Mtpa underground operation, with an estimated mine life of 20 years (OZ Minerals, 2017). First concentrate production was achieved in December 2019, within the Iron Ore Copper Gold (IOCG) hematite breccia complex. The Carrapateena orebody is overlain by 500 m of barren sediments of the Stuart Shelf, which hosts two aquifers. The cover sequence is dominated by shales, quartzites and sandstones in order of thickness. The cover sequence presented challenges to the mine ventilation system as a result of highly variable rock strengths. On this basis, the site developed the first vent rise, Vent Rise 5 (VR5), earlier than required as a means to test the empirical stability assessment. Assessment for VR5 was completed in 2017, with the mine yet to develop through much of the cover sequence. Due to the geotechnical data available at the time, it was anticipated that break out would occur within the vent rise walls as a function of the low strength Woomera shales. VR5 was developed to 4.5 mᴓ in late 2018. The timing of the VR5 development enabled the site technical team to calibrate empirical stability factors for the assessment of future vent rises. At the time of writing, four additional vent rises have been successfully developed to a diameter of 5.5 m. No significant overbreak has been observed within any of the vent rises. This paper is intended for geotechnical practitioners designing large-diameter vent rises in geological environments similar to the Stuart Shelf where a similar approach to vent rise design may be warranted.

Mar 15, 2021

The paper deals with the taking of soundings in connection with coal mining operations under part of the Pacific Ocean adjoining John Darling Colliery.INTRODUCTIONIn the early days of mining in the Newcastle District there did not appear to be any definite law specifying the limits to which mine workings, other than certain borings, could extend under tidal waters.As time went on, a figure of 120 ft. was fixed as the minimum thickness of strata between the roof of the seam and the sea bottom; beyond this mining operations are disallowed. The laws relating to working coal under tidal waters are as follow:-The minimum width of pillars to be left shall be eight (8) yards and the maximum width of bords or other excavations shall be six (6) yards, but the lessee may at his discretion increase the minimum width of the pillars or decrease the maximum width of the bordsor other excavations so as to increase the general safety.The eight (8) yard pillars shall be left unwrought.In on-road of every pair of Winning-off or leading headings, a bore shall be kept going ten (10) feet in advance for the purpose of foretelling the presence of any fissure, wash-out, open joint, fault, dyke, or otherwise, and all winning-off headings shall be driven atleast one hundred (100) yards in advance of the working bords.The most accurate and trustworthy information shall be obtained by the lessee not only' of the depth and character of the ocean bed, river, lake, or estuary deposit, but also of the strata overlying the coal seam.When working under the ocean, strata shall be bored through and proved a minimum thickness of thirty (30) feet at the face of the leading headings or levels immediately such headings or levels are under the ocean, and...

Jan 1, 1947

By J Johansson, E Lund, J Lööw, A Pekkari

Technological development is accelerating in the mining industry (Abrahamsson and Johansson, 2021) and in large parts of the world there is an increased environmental awareness (United Nations, 2015). This can mean both challenges and opportunities. The mining industry has long been criticized for its adverse environmental effects. However, there is now a lively discourse about the role of mining in facilitating the green transition towards sustainable development. Mining is increasingly recognised as a prerequisite for the green transition, by supplying key raw materials to enable, for example, digitisation and batteries for electric vehicles. The green transition not only amplifies the demand for metals and minerals but also intensifies pressure on the mining sector to assume greater responsibility for environmental and societal welfare (Dehaine et al, 2020). New technology, such as digitisation, automation, and remote control, play a crucial role in advancing towards more sustainable mining practices. Despite the expanding role of advanced technology, human involvement will remain important in the extraction process (Rogers et al, 2019), but new technology will change how miners do their work, which in turn will lead to changed competence requirements for miners (Herbert and Hidalgo, 2021) and increased need for further education. Given the significant shift towards sustainable mining, it is important to study how these changes may affect the work, competences, further education and skills of miners as human expertise will continue to be critical in the extraction process. Consequently, there is a need for proactive research to prepare for the inevitable changes and implement measures to support miners through this changeable period to ensure a smooth transition that protects miners’ safety and working environment. This extended abstract explores how new technology will affect the need for further education of miners in the future.

Sep 1, 2024

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

By T J. Callaghan

The Avebury nickel mine in Western Tasmania is a disseminated nickel sulfide deposit hosted in intensely metasomatised Cambrian ultramafic resulting from later Devonian granite related hydrothermal activity.Variable metasomatism of the ultramafic has formed two distinct gangue mineral assemblages. Less metasomatised ultramafic is comprised of fine grained black antigorite with minor disseminated chromite, magnetite and pentlandite. Intensely metasomatised ultramafic is altered to a pale grey or green, coarsely crystalline tremolite/actinolite and diopside assemblage with minor magnetite, chromite and sulfides. Both gangue mineral assemblages are frequently intermixed in ore grade mineralisation.The bimodal gangue of either serpentinite or metasomatised ultramafic presents challenges to drilling, mining, resource estimation and mineral processing as they possess very different physical properties. Mineralised serpentinite has a mean bulk density of 2.8 g/cc and the ultramafic skarn a mean bulk density of 3.2 g/cc. Physically, the ultramafic skarn is hard to break percussively creating difficulties in the crushing circuit and reducing mine development rates. However, it is non-abrasive and grinds readily, resulting in increased diamond drilling rates and increased mill throughput. Conversely the serpentinite gangue is softer and breaks easily resulting in accelerated development rates and crushing circuit throughput. However, its fibrous nature reduces grinding efficiency, increasing bond work indices and reducing diamond drilling rates.Predicting the ratio of serpentinised to metasomatised ultramafic is possible through use of the resource blockmodel, assisting mine scheduling, predicting mill throughput rates, energy consumption and grade control drilling rates.CITATION:Callaghan, T J, 2017. Challenges of bi-modal gangue mineralogy in mining geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 23–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Singh BN, Chakravarty PK, Chatterjee LM

Indian blast furnaces operate with coke gener- ally containing 24 to 28% ash compared to 10-15% ash in coke in most other parts of the world. The operating problems are further aggravated by the high alumina content and the adverse alumina to silica ratio in the ore. The above factors not only increase the coke rate but, at the same time, increase the flush slag volume, make the bosh slag highly limey and thereby viscous, and produce a flush slag containing 24 to 26% alumina. Relative- ly low flame temperatures (RAFT) make conditions more difficult. The high basicity of the bosh slag limits the maximum flush slag basicity to around 1.0, beyond which the burden movement is adversely affected by the viscosity of the bosh slag: This effect is partly controlled by operating blast furnaces with high MgO in the flush slag (around.10%), which also improves the desulphurizing power of slag. Steps are underway in some plants to inject lime through theòtuyeres to control the bosh slag basicity and also to neutralise the large quantity of silica which is released at the tuyere level from the coke ash, so that the silicon content of the hot metal can also be controlled. High bosh slag basicity coupled with the characteristics of iron ore/aggolmerates, widens the softening-melting zone and alters the shape of the softening-melting zone. This leads to operat- ing difficulties and poor hot metal quality. This paper discusses the above aspects of Indian blast furnace operation and steps being taken to surmount some of the above difficulties.

Jan 1, 1981

By Golubkov OL, Fedotov PB, Shkylar FR

One of the fundamental parameters of the race- way is its extent (a{ o), which has a significant effect on the distribution of gas and material flows in the lower region of the furnace. pp The known relationships for determination of aC o in most cases link the length of the raceway with the parameters of the blast, while the para- meters of the coke layer, in which the raceway is formed, are either ignored or else expressed in terms which are difficult to determine experimen- tally. Furthermore, the coke combustion propert- ies are not always taken into account in current blast furnace operating practice with combined blast. A complex dimensionless parameter, which re- flects the properties of the interacting media, is the ratio of the kinetic energy of the hot, com- bined gas stream to the potential energy of the coke flow, burning at the tuyere in a gas of known composition. Statistical processing of experimental data on the extent of the raceway zone, obtained from literature and our own work on operational furnac- es, has led to a working formula of the following Form:

Jan 1, 1981

By Blackwood R. L, Crichton G. P

In recent years, the value to Australia of the introduction of a system of resource rent taxation on the mining industry has been frequently debated. The forms that this rate of return based tax could take, and the impli- cations on government revenue and mining com- pany profitability have been discussed at some length. Further, the selective application of this taxation scheme to certain mining industry sectors has received considerable attention. This study takes the form of a survey of the taxation history of one significant Australian mining venture, the Mount Lyell Mining and Railway Company. The conditions faced by this company during its history are used as a base for the imposition of rent taxation schemes. Comparisons are drawn between the historical taxation liability of the company and that which would have been incurred if a resource rent form of taxation had been in existence. From the results of the study, it can be concluded that while the company can be con- sidered to have been a successful enterprise during most of its history, it has not achieved a level of profitability which would warrant the collection of any form of excess profits Tax.

Jan 1, 1979

By B F. J Kelly

Multiple-point simulation is a family of methods used to generate conditional facies simulations that present the same spatial dependence as a user-defined training image. The main advantage of using a training image is the easy integration of geological concepts in numerical subsurface models. The strength of multiple-point methods is that it allows making the best use of geological expertise when data are too sparse for inferring a model of spatial continuity. However, despite being appealing to geologists, the multiple-point methods are often not used in practice due to the difficulty of building complex 3D training images that contain realistic features.A new framework for multiple-point simulation is presented that involves small and simple training images. The main idea is to use random transformations to expand the range of structures available in the simple training image. The training image is not regarded any more as a global conceptual geological model, but rather a basic structural element of the subsurface. Complex geological structures are obtained, whose spatial structure can be parameterised by adjusting the statistics of the random transformations, based on field data or geological context. In most cases, such parameterisation is possible by adjusting two numbers only. One advantage is that the training images are so simple that they can be easily built even in 3D. The method allows building 3D models that reproduce shapes corresponding to a desired prior geological concept and are in phase with different types of field observations, such as orientation, facies or geophysical measurements. The flexibility of the approach allows for naturally integrating different types of data. This is demonstrated on an example involving seismic data assimilation. Examples where complex 3D folded structures are built from a simple training image and a few orientation data are shown.

Sep 26, 2011

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

By A Weeks an, R Bertinshaw, S Khosrowshahi

Good mining is central to any approach to value tracking. Good mining occurs where the ore is correctly delineated, measured and fed to the mill. This process is usually referred to as grade control, ore control or quality control. There are now ways to measure the efficiency of this process, such as by using conditional simulation, and a brief synopsis is presented. Resource estimation is the foundation of ore reserve estimation, which should enable useful prediction of the expected metal to be recovered from mining and milling. Significant improvements have resulted from applying new techniques such as the Chain of Mining (CoM) method, which models the mining process. Again, a brief synopsis is presented. Tracking value from the mine through the mill implies a linear sequence of processes that can be modelled. Reality is more complex and there are error components, feedback loops and breaks in the Chain of Value. Modelling the total production process in a number of operations is considered, including the various impacts on producing reconciliations. Procedures are also discussed for handling a number of difficult issues such as: different data supports, stockpiling strategies, blending from multiple ore sources, blast movement and underground ore extraction.

Jan 1, 2002

Incremental sampling is defined as a solution to fight segregation, the theory is demonstrated and theoretical and practical aspects are discussed. The number of increments necessary for successful sampling is discussed. As an application, riffle splitter division is reviewed.

Mar 1, 2010

A microcomputer based expert system is presented for fast and cheap mineral identification. Because of the increasing pipularityof and interest for minerals and precious stones (selling, hobby polishing, collecting, teaching etc.) we pointedly deal with gemstone identification. In most cases only some fundamental data are needed to identify a mineral sample (or precious stone) if we know how to use these data. The important, characterizing data of the well-known minerals are stored in the data-base of our program-system. The visible and measured optical and physical properties of the sample are compared adequately with the stored data to get the result, the name of the examined mineral. The system works in a simple, friendly way - asking questions, understanding answers - so that no special computer knowledge is necessary to use it, only the answers should be typed in. The main advantage of the system is that only relatively simple and fast measure-ments are required. Based on these measurements a fast, reliable identification is processed on a cheap com-puter running a sophisticated program-system. The MINTEST system handles even those cases when the tested mineral cannot be determined based on the given input data.

Jan 1, 1985

By A G. Shellsh, R J. Henham, J R. Foley

The Porgera Gold Mine, west of Mt Hagen in PNG is a large open pit and underground operation currently producing gold at the rate of almost one million ounces per year. This deposit has produced some 8.8 million ounces to-date and has current reserves of 103.4 million tonnes @3.2 g/t Au. The Porgera Joint Venture has invested over $A1 billion in infrastructure in this project. Technical management of this operation involves the interrogation of some 700 000 metres of diamond drilling, some 50 000 blastholes per year, and very large volumes of laboratory, geotechnical, environmental and production reporting data. Over the past seven years this data has been consolidated into a single centralised, relational database which now acts as the single reference point for all the technical application systems used for surveying, grade control, production reporting, deposit evaluation and modelling. Data transfer to application programs and management systems is controlled by the centralised database, this process at times involving a two-way, real-time, binary data transfer. The benefits of a specialised database application include security and integrity of the data asset, ease of access, and performance in a multi-user environment. This replaced fragmented, inconsistent data sets stored inefficiently as individual, unindexed, variably formatted files associated with the different application programs. Most importantly, the database has allowed mine management at all levels to make timely, confident investment, cash flow and optimisation decisions as it provides the primary link between the deposit and operational data sets on one hand, and the application programs and management and performance measurement systems on the other. This paper discusses the economic value and importance of technical data in terms of the resource asset and the means by which this data is being managed and used at Porgera.

Jan 1, 2000

By B McFadyen, Y Potvin, K Woodward

The Australian Centre for Geomechanics (ACG) held two workshops in 2019—one in Australia and one in Canada—to discuss processes and methods currently used in the mining industry for stope design and reconciliation. In practice, this work strives to optimise stope performance and aims to maximise ore recovery (minimise underbreak), while minimising dilution (overbreak). One of the key findings from the workshops was that current stope design practices, almost exclusively, rely on some versions of the empirical Stability Graph methods developed in 1980s. Although robust and useful at the feasibility study stage, there are a number of inherent shortcomings with this approach. The Stability Graph’s limitations first lie in that it cannot assess underbreak, which is a very important measure of performance. Furthermore, the method doesn’t consider a number of factors which often have a critical influence on stope stability, for example, drilling and blasting or the presence of faults. Given the current industry standard practice, there is a great opportunity to reinvent the stope design process to optimise performance. A finding of the workshops was that every mine quantifies stope performance in terms of volume reconciliation with a focus on dilution and ore losses, and reconciling metal tonnes recovered from the mill. Many mines further investigate stope performance by looking at individual stope faces and the causes for the deviations between the planned stope shape and the measured cavity. Recent research at the ACG has shown that investigating overbreak and underbreak at a higher resolution is a powerful way to identify the root causes of overbreak and underbreak. Finer scale assessment is achieved using an octree analyses, which effectively divides the relevant stope volume into cubes on the scale of a metre and produces many tens of thousands of data points. The octree data structure and subsequent analysis underpins a data-driven stope design methodology. The ACG is currently developing a design approach based on multivariate modelling methods that can account for the many variables that influence stope performance and forecast stope overbreak and underbreak results. Back-analysing stopes based on octree reconciliation results provides a rich database for training the model. Once the model can achieve reliable forecasting of overbreak and underbreak, an interactive drill-and-blast design will allow for the assessment of different firing strategies to optimise stope performance.

Mar 15, 2021

The subject of steel wire ropes covers such a wide range of points that it would be impossible to deal with it fully in one paper, and in view of the apparent scarcity of published information on the subject it is proposed in this paper to deal with those items which should give the mining engineer a better understanding of the basic factors which affect the design.selection, and use of ropes. The matter will be considered under the following headings:-1. Brief history of steel wire rope-making.2. Rope-making terms.3. Wire rope materials.4. Characteristics affecting economy, operating life, and serviceability of a rope.5. Properties of construction of rope, and stresses met with in wire ropes.6. Drum and sheave sizes and sheave bearing pressures.7. Storage, handling, and maintenance of ropes in service.8. Common factors affecting rope life, particularly winding and haulage ropes.9. Inspection of ropes.GENERALWire rope, which was invented for, and first applied to mine winding, has become an indispensable aUXiliary throughout the whole field of mining, be it for underground, open cut, or dredge work, as well as the requirements of transport and treatment of ores.Though wire ropes appear simple collections of wire and fibre, the demands made upon them are many, and the stresses and abuses to which they are exposed in service are varying, and often of serious dimensions.The exposition of these stresses and abuses, particularly dynamic stressing, corrosion, etc., all of which seriously affect the safety and economical life of the ropes, is often enough to frighten most practising mine staffs, who are aware that before the requirements of economic operation stands the still more important question of safety in mining.

Jan 1, 1947

By Blattner P

The Late Miocene gold-silver bearing epithermal system at Waihi has some close similarities in its paleo-thermal and -geochemical structure with modern, volcanic-hosted geothermal systems such as Ohaaki-Broadlands. At Waihi an extensive braided quartz vein system is enveloped by hydrothermally altered andesites with minor tuff breccias and tuffs. A main stage of vein filling consists of multiple phases of chalcedonic quartz and fine to medium grained quartz, which are accompanied by pyrite, sphalerite, galena, chalcopyrite and acanthite below the base of oxidation. Platy calcite is present locally. Fluid inclusion studies indicate that the main stage quartz was deposited at temperatures of 189¦-273¦C from dilute (T¦ of -0.1 to -1.0¦C) fluids that were locally boiling. Homogenisation temperature Th versus T. data points lie within the field enveloped by dilution and boiling/gas loss paths determined for the Ohaaki geothermal field, and indicates that the parent hydrothermal fluid for the Waihi epithermal system had a similar composition to that at Ohaaki, ie 0.2 wt% equiv NaCI and 3.3 wt% equiv CO2. The hydrothermal alteration mineralogy and the isotopic composition of vein calcite indicate that the hydrothermal fluid contained relatively high concentrations of CO 2' as at Ohaaki. Oxygen isotope analyses of main stage quartz range from 6.1 to 11.6 %o and of vein calcite from 2.29 to 9.4% . Calculated d8Ow.½ values for the hydrothermal fluid that deposited the main stage quartz range from - 2.0 to -5.7%c , with a trend to less negative values with depth. They are similar to those in the deep chloride fluid in active geothermal systems with a substantial fluid throughput. A high fluid throughput at Waihi system is also evident from the extensive high intensity hydrothermal alteration and large volume of quartz deposited in the vein system.

Jan 1, 1995

By Prince R. G H, Guerney P. J, Frew J. A, Vanderkruk C. R, Wanigasekara-Mohoti D. K

This computer-aided design system for mineral processing flowsheets which are based on froth flotation, size reduction and classification combines an expert system for generating flowsheet structures with numerical models for the physical processes and the economics. Design decisions, such as specification, size and placing of process units and the destination of recycle streams, are based on clear technical and economic criteria. These decisions are controlled by user-set parameters, which allow the incorporation of industry experience and preferences and the generation of sets of good designs, from which choices may be made by further criteria, such as controllability. Liberation is now fully modelled and the early results from this extension continue to suggest potential substantial increases in added value over conventional approaches.

Jan 1, 1997

By R Dimitrakopoulos

The development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and may require the use of stochastic conditional simulation techniques. Multiple-point methods have been developed for petroleum reservoir modelling, enabling reproduction of complex geological geometries. This paper considers a multiple-point approach to capture the uncertainty of the lithological model. The implementation of the method at the Yandi channel iron ore deposit in Western Australia and performance characteristics are discussed. The uncertain lithological model translates into considerable grade-tonnage uncertainty.

Jan 1, 2007