Search Documents

By J Planner

As Australia’s coal and iron ore export volumes increase to meet international market growth, port terminals, mining operations and rail transport systems can be the source of increased dust emission. Current and future sustainable expansion must minimise dust emission from bulk handling and transport operations located in close proximity to residential areas. Lower level dust emissions can be controlled by operational measures such as water addition to products, and use of water spray on stockpile surfaces. Recent research has shown that higher levels of dust emission can be more effectively controlled by understanding and treating the dust characteristics of each individual bulk product. Application of this research, progressively being applied at Australia’s coal and iron ore port terminals and rail transport systems, is achieving compliance with health standards and minimising dust nuisance effects to an acceptable level.

Nov 22, 2011

By Just GD, Gillies ADS

There is an increasing need for reliable and comparable coal resource data and it is necessary to standardize the traditional classification procedures by quantifying the three basic evaluation criteria of economic feasibility, geologic assurance and recovery. For well documented deposits, geostatistical methods can consider- ably improve classification quality. A geostatistically based algorithm for classifying coal resources within the current Queensland and New South Wales codes has been developed. Application of the method in classifying resources from a number of seams exhibiting different structural characteristics is assessed. The method is found to give classification results which closely reflect the error associated with an estimate of resource quantities based on current sampling densi- ties. It requires a careful geostatistical analysis with emphasis on geological awareness. Resource category restrictions must be arbi- trarily assigned and remain constant for all deposits being compared. Engineering judgement is needed and interpretation may be required with isolated and peripheral blocks.

Jan 1, 1987

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

By J Lombardi, M Weidenbach

"OZ MineralsÆ Prominent Hill copper-gold concentrator is located 650 km north-east of Adelaide, 130 km north-east of BHP BillitonÆs Olympic Dam operation and 130 km south-east of the regional township of Coober Pedy, in the Gawler Craton region of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 10 Mt/a ore throughput capacity, operating well over the design rate of 8 Mt/a. Increased throughput rates have seen a decreased water recovery from the tailing thickener due to operating above design. Subsequently, greater pressure was placed on the site water balance and bore field off-take rates due to increased evaporation losses from greater volumes of water reporting to the tailing storage facility. This resulted in a trade-off between water availability and milling rates as part of the operating strategy.Two projects were implemented to increase the tailing thickener underflow density, thus improving water recovery directly back into the operating plant, reducing water losses via evaporation and decreasing the reliance on the bore field system operating at maximum rates to maintain mill throughput. The two projects were: tailing thickener feedwell redesign implementation of the Manta Cube control system.This paper discusses the background, implementation and benefits attained from these two key projects. Combined they have allowed a two to three per cent increase in tailing thickener underflow density to be consistently achieved, which has allowed greater water recovery. As a result, the processing plant has been able to operate at higher throughput rates when required, with greater water availability in the process plant recirculating system and a reduction in occurrences of the plant being æslowed downÆ due to water supply shortfalls. Both projects have also delivered a significant reduction in flocculant usage.CITATION:Weidenbach, M and Lombardi, J, 2012. Tailing thickener operability and control improvements at Prominent Hill, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 137-142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 29, 2012

The weathering profile, in arid terrains, is commonly capped by different kinds of hardened crust, whose formation is related to recent or former climates. One may distinguish silcretes, calcretes and the ferruginous (or ferro-aluminous) laterites. the present keynote address mostly deals with the lateritic regolith and, moreover, the influence it has on mineral exploration. The lateritic regolith, also called "cuirasse", is a result of a massive accumulation of Fe (and/or Al) oxides on top of weathering profiles developed during former, probably seasonal humid, climatic episodes, and whose preservation depends on the characteristics of later climates. The total thickness of such weathering profiles commonly exceeds 50 m, with an almost complete substitution of the rock forming minerals by secondary minerals as kaolinite and Fe-Al oxi- hydroxides (hematite, goethite, boehmite, gibbsite). Such an alteration of the primary minerals assemblage is of course accompanied by significant changes of the chemical composition, as concerns major and trace elements. The latter are distributed amongst the main secondary mineral phases or trapped in some primary resistant minerals, but may also be leached, totally or partially. Gold is also affected by lateritic weathering, as shown for instance by morphoscopic and geochemical studies of gold grains collected in the different horizons of the profile, which indicates some dissolution followed by reprecipitation.

Jan 1, 1988

By J Herrmann, J Richards, B Hutchison

An extensive trial of laser-based survey and monitoring systems at Hillgrove Resources Kanmantoo Copper Mine in the Adelaide Hills, South Australia, has proved the capabilities of the system in monitoring rock movements on open pit walls. Initially, the trial involved deploying a Maptek I-Site 8820 laser scanner and the proof-of-concept Maptek Sentry software in the Nugent Pit to monitor ductile rock movements located up to 260 m away. The system was proven to be capable of monitoring various rock movements from 1.5 tonne rockfalls up to a 40 m high toppling wall failure. Data collected from smaller rockfalls was used to help build a database for Hillgrove’s rockfall management program. As part of the trial, the laser scanner was deployed to monitor a ramp movement event, as well as the toppling failure, adjacent to an IBIS slope stability radar. Both devices monitored the slump and the slowly developing toppling movements, with similar results. Although the radar was used as the successful ‘critical alarm’ device for the toppling failure, post-failure analysis showed the laser-based system to be capable of performing a similar role in the ductile rock regime; albeit over much shorter distances than the radar capability. A second laser scanner was deployed to monitor Kanmantoo’s Emily Pit in early December 2014, where it successfully provided critical alarm warnings for a block topple event. Sentry software, which takes advantage of Maptek I-Site 3D spatial imaging technology, was first released in November 2014 to meet industry demand for a cost effective, flexible system to detect movement. Sentry has now been re-launched as a fully transportable monitoring system. Deployed in a custom trailer, the system offers a power and communications module, cellular and Wi-Fi networking and a stable bollard for the I-Site laser scanner and Sentry software. This paper will present rock wall movement data from the Sentry trial and a subsequent two years of monitoring of the open pit walls at the Kanmantoo Copper Mine, at distances out to 750m. In addition, examples of remote geological mapping and small rockfall detection, using the laser scans, will be described. The Sentry system has proven to be beneficial for the continual improvement of slope monitoring and risk management at hard rock mines. CITATION:Hutchison, B, Richards, J, Richards, J and Herrmann, J, 2018. Mine rockfall and rock wall failures – proven digital laser-based approach for monitoring slopes at the Kanmantoo Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 463–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D Reid, J McKibben, M Noppe

International mineral disclosure standards and guidelines aligned with the CRIRSCO (Committee for Mineral Reserves International Reporting Standards) template were developed to inform stakeholders about the relative accuracy and confidence levels of publicly reported information and to support investment decisions, particularly when advancing projects through different development stages. The traditional stages range from early to advanced exploration, through pre-development (with Mineral Resources and pre-feasibility and/or feasibility levels of study) before the final development stages, where a decision to proceed with construction or production (or both) is made. The traditional definition of Mineral Resource and Ore/Mineral Reserve classification categories and techno-economic study levels (including Preliminary Economic Assessment (PEA), Scoping Study (SS), Pre-Feasibility Study (PFS) and Feasibility Study (FS)) were defined with pre-development project assessment in mind. As such, these definitions are not necessarily well aligned to the reporting structures required by operating mines which need to consider a range of timelines spanning short to long-term operating conditions. However, the same terminology and definitions are used, or expected to be used, by both project developers and mine operators when reporting resources, reserves and techno-economic study outcomes. This paper discusses how various stakeholders in the minerals industry (including competent/qualified persons, mining company leaders, investors, lenders and regulators), generally interpret the definitions of Mineral Resource and Ore Reserve categories in terms of the relative accuracy of the estimates, their link to techno-economic study levels and their contribution to life-of-mine (LOM) schedules. The paper examines the degree to which mining companies recognise, and apply, enhanced operational knowledge to reflect short-term views of the relative accuracy and confidence levels associated with publicly reported Mineral Resource and Ore Reserve estimates and forecasts. Furthermore, this paper explores how this knowledge is applied to support ongoing Mineral Resource, and particularly Ore Reserve, generation and reporting. This paper is informed by public data and responses to an internal survey prepared by the authors and completed in 2021 by several mining companies.

Mar 22, 2022

By S M. Aminossadati, C M. Stewart, M S. Kizil

Mine ventilation models are now an accepted component of most mine management systems. However, modern ventilation models also represent a highly structured spatial data source, defining underground pathways and connections across a mine. This creates opportunities to extend the use of network models beyond ventilation design, by using critical path algorithms to find pathways such as minimum distance or minimum time.This paper explores the use of ventilation network models to automatically analyse and calculate potential emergency escape routes. A variation of Dijkstra’s algorithm is used to predict complex pathways between any two points across a model, representing an escape route from an emergency area (such as a fire) to a safe location (such as the surface or a refuge station). Weighting can be assigned to paths to represent potential travel speed, obstructions or preferred routes. Finally, emergency considerations such as smoke or gas in some parts of the mine can then be incorporated into the pathways to force the algorithm to avoid dangerous routes and specify safer pathways. Ventsim is used to visually show example results.Emergency egress pathway prediction using ventilation network models can provide an efficient way to quickly predict the quickest or most efficient escape routes for emergencies or planning purposes.CITATION:Stewart, C M, Aminossadati, S M and Kizil, M S, 2017. Emergency egress pathway prediction using ventilation models, in Proceedings Australian Mine Vent Conference 2017, pp 57–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Grader F. E

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effective- ness of separation depends on the energising current of the separator, the frequency of the a.c. cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150um +74pm) on the linear motor surface has been observed using a cine camera. An attempt has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an a.c. cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear meter surf, e.

Jan 1, 1980

By J Zhou

Gold in sulfide ores is associated predominantly with sulfide minerals and occurs as both microscopic and submicroscopic particles. In non-refractory sulfide ores, gold occurs mainly as coarse- and medium-grained particles. Minute inclusions and submicroscopic gold usually account for a minor portion. In contrast, gold in refractory sulfide ores occurs mainly as minute particles and submicroscopic gold, and microscopic gold usually accounts for an insignificant portion. In gold ores containing carbonaceous material, the preg-robbing nature of carbonaceous material may impose challenges on gold extraction and cause gold losses. To extract gold from refractory sulfide ores, the ore needs to be finely ground and preoxidation is often required. Sulfide host minerals must first be oxidised to create a porous structure through which the cyanide leach solution can penetrate to reach the colloidal gold particles. The oxidation is traditionally achieved by roasting, autoclaving or bacterial oxidation. In carbonaceous sulfide ores exhibiting a preg-robbing nature, the carbonaceous material needs to be treated by roasting, autoclaving or other means to minimise the preg-robbing effect. As a predictive and troubleshooting tool, the gold deportment study plays an important role in gold metallurgy. It determines the deportment of gold in an ore or mill product and identifies the mineralogical issues that may affect or may have affected gold extraction. The information acquired from a gold deportment study can be used to assist in process selection, flow sheet development, recovery improvement and reagent optimisation.CITATION:Zhou, J, 2013. Deportment of gold in sulfide ores and implications for gold extraction, in Proceedings World Gold 2013 , pp 433-442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The Mt Lyell Mine at Queenstown, Tasmania was re-opened in 1995 by Copper Mines of Tasmania Pty Ltd, a wholly owned subsidiary of Mt Lyell Mining Co Ltd. The re-opening followed over 100 years of copper and gold mining at Mt Lyell. Major changes in practice were implemented across the site. Preventing further damage to an already disturbed environment was a major priority. Sublevel caving, at a lower cut-off grade, replaced open stoping for the deep underground mining. Development and later stoping are handled by a contractor, National Mine Management Pty Ltd, in the largest underground contract awarded at the time. Large scale sublevel caving was new to Mt Lyell and not widely practised in Australia, requiring studies and systematic development of the method, particularly in drilling and blasting. Rehabilitation and upgrading of mine infrastructure have been and will continue to be a challenge. The mine has, since 1995, returned to being a stable producer with potential for growth.

Jan 1, 1998

By M Watkinson

Tube bundle monitoring systems have come a long way from their first introduction to coal mining in the late 1960s/1970s. Early developments in the United Kingdom (UK) commenced with single gas analysers (carbon monoxide) and quickly moved towards introducing oxygen analysers and methane analysers for improved analysis, in particular the calculation of air-free results. Recommendations were made in the early days as to how and where to run tubes and on the matching of sample pump and purge pump pressures. Current Australian installations are commonly based on a four-gas multianalyser, infrared for carbon monoxide, carbon dioxide and methane, and paramagnetic for oxygen. These systems are controlled with programmable logic controllers (PLC), with component monitoring as an integral part of the software. This paper discusses the development of tube bundle systems from the 1960s to the current date and looks at the advantages and disadvantages of the installations, along with making operational recommendations to be considered with the siting of the analyser building, running of tubes and maintenance of the system.CITATION:Watkinson, M, 2015. Developments in tube bundle gas monitoring, in Proceedings The Australian Mine Ventilation Conference, pp 259–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The Porgera mine and treatment plant are located in the Enga Province of Papua New Guinea. Gold in the Porgera deposit is found free and in association with the primary sulphide mineral pyrite. The refractory nature of the gold in the pyrite r

Jan 1, 1997

By D Walker, A Tsvetkov, P Voigt, O Kloiber-Deane

The GPM Gold Operation has been employing an Albion Process™ plant at its Sotk (Zod) gold mine in Armenia since 2014. Long term data from the operation is now being published for the first time. The data presented includes concentrate throughput, as feed to the Albion Process™ plant (tonnes per day), sulphur grade in concentrate (% S), total sulphide sulphur oxidation in the Albion Process™ plant (% SOx) and gold recovery from Albion Process™ plant residues (%). The data provides a basis for evaluation of the effectiveness of the commissioning, ramp up and operation of the Albion Process™ plant. Notwithstanding the impact of a slower concentrator commissioning than expected, the plant demonstrates Series 1 behaviour on McNulty ramp up curves, indicating successful commissioning and fast ramp up. Interrogation of the data and operational experience indicates that this successful operation is a result of a process that is flexible, robust and stable, one that was designed well based on solid testwork results and pilot plant trials during the study phase undertaken by Glencore Technology and Core Resources, and where the local operators were provided with appropriate training in operation of the plant. CITATION:Voigt, P, Walker, D, Kloiber-Deane, O and Tsvetkov, A, 2018. Ramp-up and long-term performance of the Albion Process™ plant at GeoProMining Gold Armenia, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 339–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Various methods and software have been trialled for simulation of Au grades at Boddington Mine. This covers in-house and public software as well as sequential and turning bands methods. The diversity of options was further expanded with comparison of point and direct block simulation. Some difficulties were encountered in incorporating high-grade restrictions. Altering parameters or software can make very significant differences and give results varying from estimations. This paper details a new simulation run with validation and tests for local calibration (or progressive correction) of the simulations to the estimations, focusing on reproduction of statistics. This approach brings to the forefront the question æwhat is the purpose of the simulations?Æ Results and some ideas for future applications at Boddington are summarised.

Sep 26, 2011

By G Lane, M Bueno

In a recent publication (Bueno and Lane, 2011) the authors presented the analysis of a consolidated dataset composed by 137 autogenous/semi-autogenous grinding (AG/SAG) mill pilot trials. By comparing the measured data against theoretical specific energy consumption, the analysis indicated which circuit configurations were more or less energy efficient. However, the analysis has also indicated that the energy efficiency of each of the types of circuits vary significantly.There are numerous factors that contribute to the variations of energy efficiency of AG/SAG mill-based circuits, such as feed size distribution, recycle ratios and ore characteristics. In view of this, the present work accesses these factors individually and discusses what may lead a particular circuit configuration to be more or less efficient in terms of energy and costs.CITATION:Bueno, M and Lane, G, 2012. Key drivers of energy and cost efficiency in autogenous/semi-autogenous grinding circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 113-118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Blasting is an essential component of most mining operations, and is used to reduce the rock mass to a workable size distribution, as well as to create stable openings and pit walls. Frequently, there is little difference between the designs of blasts to achieve these two functions, though more advanced operations have developed different designs for these very different functions. To assist in the appreciation of how blasting practices can impact on the stability of rock openings and pit excavations, this paper reviews the role of high pressure explosion gases on final block stability. It is assumed that the stability of all surface and underground excavations are, to a greater or lesser extent, controlled by the interaction between discrete rock blocks. Typically, these blocks will be defined by either natural, or excavation induced, jointing.

Jan 1, 1999

By W Assibey-Bonsu

The paper provides a brief review of the multivariate uniform conditioning and the localised multivariate uniform conditioning techniques and presents a case study based on a porphyry copper gold deposit in Peru. Two other important scenarios have been investigated and will be particularly emphasised: The recovered selective mining unit (SMU)s depend on a combination of copper and gold content, which can be expressed by means of ænet smelter returnsÆ (NSR). Two approaches are compared. Firstly, the application of a composite cut-off on NSR on the joint distribution of each grade and the application of uniform conditioning to three variables is investigated, ie for the first approach NSR is used as the main variable. The second approach considers copper as the main variable. In the case of multiple domains the procedure used to apply the technique to process mixed panels is clarified and recommendations are made.

Sep 26, 2011

By M Z. Abzalov

Drilling mineral sand deposits has specific challenges, which are different from drilling hard rock deposits: Drilled sequences are represented by non-consolidated free-flowing sands to semi-consolidated clayey sands and indurated layers. Valuable heavy minerals (ilmenite, rutile, zircon, leucoxene) have an average density of 4.6 g/cm3, which is significantly heavier than the hosting sand matrix; mainly represented by quartz (density = 2.6 g/cm3). The large difference in the mineral densities can result in sample segregation in the drilling rods and capturing devices causing biased composition of the recovered samples. The drilled strata can contain beds of consolidated sediments, hard pan lenses and concretions. Therefore, chosen drilling equipment should be flexible and permit a switch from drilling the free-flowing sands to hard rock drilling. Thickness of the sand hosted mineralisation varies from several metres to more than 170 m. Mineralisation is distributed above and below the water table. Evaluation of the mineral sands deposits is based on hundreds of drill holes and many thousands of samples, therefore drilling methods should be fast and cost effective. The drilling methods commonly used for mineral sand deposit evaluation, include aircore, triple tube diamond and sonic; including its variants, such as vibrocore drilling technique. The ability of the studied drilling techniques to properly address the above listed challenges in mineral sand deposits, whilst maximising the quality of the obtained samples has been compared in three deposits: Corridor Sands (Mozambique), Richards Bay (Republic of South Africa) and Fort-Dauphin (Madagascar).This study has shown that aircore samples tend to be negatively grade biased, underestimating the heavy minerals content, in particular when drilled intervals are located below the water table. Triple tube diamond core method can produce non-biased samples. However, results can be marred by incorrectly chosen drilling mud. Sonic drilling is a relatively new technique based on a high frequency vibratory technology. It is the only production drilling technique that allows a continuous relatively undisturbed sample of unlithified sands to be obtained. The main limitations of this technology preventing its wider use for developing mineral sand resources are the relatively high drilling costs, in particular when the depth of drilling exceeds 100 m, and speed of drilling advance.

Oct 5, 2011

By G Zhao, S Hapugoda, E R. Ramanaidou, P Hapugoda, Y Jin, G O’Brien

In 2021 the ports of Port Hedland and Dampier in the Pilbara Region of Western Australia handled 900 Mt of iron ore. This ore was produced in the Hamersley’s mines and transported by trains to the ports for subsequent export. Dust, which is generally considered to be particles less than 100 μm in diameter, is generated at all steps in the supply chain. Whilst all dust may have potential impacts on human health and mangroves and buildings a proportion of the dust is classed as respirable (PM10) dust, which consists of particles <10 μm in diameter. In 2021, in response to the community concern with iron ore dust, CSIRO commissioned an internal study to characterise and benchmark the dustiness of the different ores and to develop targeted strategies to minimise dust impacts, without affecting other iron properties, such as stickiness during transportation. A specific concern is that that the dust in the PM10 fraction may contain significant amounts of particulates, such as free silicates which may have health implications for the workers and residents. This study provided detailed mineral and chemical characterisation of the dust generated from the railed fine ore products for five generic Australian ore types: Australian Channel iron Deposit (ACID), Australian Brockman (AB), Australian Marra Mamba (AMM), Australian Pilbara (AP) and Australian magnetite (AM). The dust from these fine ore products were compared to that generated from a sample of Brazilian Hematite (BH) type ore fines. The ores were evaluated for their physical, chemical and mineralogy properties, dust generating potential and understandings of the relationship between the dustiness of iron ores and their physiochemical properties. The size distributions of the railed fine ore products were determined and a suite of analyses were conducted on subsamples of total (-106 μm) and fine (-38 μm) dust. For all the ores, the total dust fraction contains less Fe and more contaminants (SiO2 and Al2O3) than did the bulk ore. The fine dust fraction contained even less Fe and more contaminants (SiO2 and Al2O3) than the total dust fraction. This suggests that the iron ore dust contains more clay and potentially free silica than does the bulk ore. These findings were supported by optical and Scanning electron microscopy analyses of the samples. Dustiness measurements were made for each of the different ores (-106 μm) to investigate the relationship of dustiness of various iron ores with their physiochemical properties and assess their responses to dust suppression by the application of water sprays.

Sep 18, 2023