Search Documents

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

By D Craw, J Youngson

Recent exploration for mesothermal gold deposits in the Otago Schist has focussed largely on extensions of, or analogies to, the reverse fault-hosted Hyde-Macraes Shear Zone deposit. Abundant normal fault-hosted mesothermal and epithermal vein deposits in the Otago Schist have attracted less attention, largely because they have limited lateral extent and steeper dips. Northwest-striking normal fault-hosted vein sets near Barewood and Hindon in east Otago crosscut schist foliation on the Barewood-Hindon plateau at a high angle along a combined strike length in excess of 20 kilometres. The trend of the vein sets is not linear, but rather contains several right lateral steps. Almost all veins dip steeply to the northeast. Angular discordance between schist foliation and the plateau surface along the trend increases from near zero at the northwest end of the veins to about 30¦ at the southeast end. Crude formation depth estimates decrease from about 7.5 km at the Barewood end of the zone to

Jan 1, 2002

A quantitative chemical model of the rocks of the Broken Hill lode environment is presented to illustrate a stratiform orebody in a meaningful form to scientists interested in environmental control on the chemicalcomposition of sediments.Even though this study was restricted by the narrow range of rock analyses available it is obvious that significant chemical differences exist between the various rock units and also that some association of metallic sulphides with Ca, Mn, Fe, and P is indicated.Correlation of this evidence with that from other mining fields may point out more definite chemical relationships and elucidate the puzzle of the mode of formation of many stratiform orebodies.

Jan 1, 1968

The Effect of Mineral Liberation on the Floatabilities of Pyrite, Arsenopyrite and Arsenian Pyrite for Carlin Trend Ores

Sep 13, 2010

By E Heath, F McDermott, S Turner, P van Calsteren

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath midocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and om, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100 000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50 000 years prior to eruption.

Jan 1, 1995

By N M. Caira

The North Arm of Sulawesi hosts numerous gold and base metal occurrences. Compilation and analysis of geological, tectonic, geochemical and isotopic age date data collected over the past six years on the central part of this region have resulted in the definition of 184 prospects and mineral occurrences of various styles occurring in diverse geological settings representing varying tectonic environments and erosional levels. Mineralisation of the following styles have been recognised: porphyry Cu-Au; porphyry-related gold and base metal veins; high-sulphidation Cu-Au-As; low-sulphidation epithermal Au; hydrothermal breccias; and sediment-hosted Au mineralisation. Clusters of occurrences/prospects form mineralised districts representative of magmatic systems with characteristics determined by the tectonic environment prevailing during formation and the subsequent level of exposure by erosion. Distinctly different Miocene and Pliocene porphyry systems are now recognised whilst most of the remaining epithermal mineralisation is thought to be Pliocene or later. The central North Arm of Sulawesi is composed of a Miocene magmatic island arc that is built on an Early Tertiary basement of predominantly oceanic basaltic rocks and overprinted by a Pliocene magmatic arc. A structural fabric dominated by SSE arc-normal and ESE arc-parallel faults was established during the Miocene under a dextral wrench regime and intersections of these major fault sets are favoured sites for Miocene porphyry Cu-Au mineralisation. Strong dextral tension caused by the collision of the Sula Platform, at the close of the Miocene, led to arc-parallel rifting. Sinistral reactivation of the major Miocene structures in the Pliocene led to further rifting, and ENE-dilation. Pliocene intrusions and related mineralisation exploit these dilatant settings. Miocene porphyry Cu-Au mineralisation occurs where late-Miocene quartz diorite stocks have intruded the margins of earlier Miocene plutons of intermediate composition. Porphyry centres have associated peripheral base metal veins, and skarns. Overprinting of porphyry vein sets by epithermal veins is common. Sediment-hosted gold mineralisation occurs in calcareous sediments associated with the Miocene arc. Remnants of the Pliocene volcanic arc, comprised of dacite volcanics, intrusions and voluminous pyroclastics, dominate the south coast and host porphyry Cu-Au, high sulphidation Cu-Au-As deposits, low-sulphidation epithermal Au veins and disseminated gold mineralisation. In some prospects, mineralised sinters are preserved adjacent to vein systems and deeper mineralised stockworks. Diatremes are common and large caldera structures have been identified. Pliocene stocks and porphyry dyke swarms penetrate the main central and northern parts of the Miocene- arc introducing additional porphyry Cu-Au, base metal hydrothermal breccias and low-sulphidation gold veins. Rapid uplift and erosion has resulted in a highly variable preservation of styles of mineralisation adding further diversity within the mineralised districts and telescoping within deposits.

Jan 1, 1999

By S F. Simmons

At Broadlands-Ohaaki geothermal system, TVZ, mineral distribution patterns in geothermal wells are analogous to those in epithermal veins. Fluid flow through geothermal wells is focused over vertical intervals >500 m with discharge at rates up to 90 l/s. Focused flow at similar rates also occurs in natural systems where hydrothermal eruption vents provide enhanced vertical permeability. These vents are commonly aligned with the tectonic fabric, indicating fault control at depth. We suggest that host rock strength and structural context exert significant control on the hydrological regime conducive to epithermal mineralisation.

Jan 1, 2005

By D A. Vogel

"Sampling may be mandatory for safety or environmental reasons. It may be because the value of a sale needs to be determined or to provide important data for investments. Whatever the reason, an incorrect sample will come at a risk. Only the person that relies on sampling data can imagine what the potential cost of such risk is.Sampling itself has a cost too; the direct cost of a quality control department and indirect cost for interrupting a process, such as stopping a conveyor belt during loading. If all material is the same then only one small sample is enough. But if all the material is different, then a very large sample must be tested; in the conveyor belt scenario it must be stopped very frequently and the associated cost will be high.A good sampling plan finds the proper balance between risk and cost. A good sample must be small enough to handle yet large enough to be representative for what information is required. All good samples have three things in common: there was proper access to the material the sampling tool allowed equal probability of particles being selected nothing was disregarded, everything was included.This too is the core of Gy’s ideal sampling scenario, where all particles have the same probability of being selected and included in the sample. There is risk of bias when part of a lot is excluded from the sample. Extra care is needed when sampling particularly heterogeneous, segregated or layered materials. The sampling tool should never systematically leave out a portion; it shall not push aside large or hard particles. Wet samples shall not stick to the sampling tool. This extends to sample preparation too when reducing particle size and dividing the sample in the process.CITATION:Vogel, D A, 2017. Access, select, include – a review of the commercial sampling of traded bulk commodities in the context of Gy’s Theory of Sampling, in Proceedings Eighth World Conference on Sampling and Blending, pp 367–378 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By W Herrmann, R R. Large

Volcanic-hosted massive sulfide (VHMS) deposits in ancient, submarine volcanic belts of Australia include mound, lens and sheet-style Zn-rich polymetallic deposits, massive and disseminated pyritic Cu-Au deposits and disseminated, stratabound Au-only deposits. Variation in morphologies, metal ratios, volcanic environments and alteration features indicates there exists a spectrum of deposits from the classic VHMS model, to hybrids between VHMS-porphyry Cu and VHMS-epithermal end members. Zn-rich, polymetallic deposits form eitheron, or just below, the seafloor, whereas the Cu-Au and Au-only deposits form sub-seafloor by replacement of specific volcanic lithologies. Alteration zoned outwards from quartz -> chlorite -> sericite ¦ carbonate is typical of VHMS deposits across the spectrum. Quartz and carbonate alteration is dominant in the Au-only systems,chlorite alteration is commonly developed close to Cu-rich ores, and sericite and carbonate alteration zones are well developed in the stratiform Zn-rich ores. The most useful geochemical vectors for Zn-rich ores are the alteration index [AI=100(MgO + K2O)/(MgO + K2O + CaO + Na2O)], the chlorite-carbonate-pyrite index [CCPI=100(MgO + FeO)/(MgO + FeO + K2O + Na2O)], Mn content of carbonate, Mg/(Mg+Fe) ratio of chlorite,whole-rock Tl, Sb and Ba/Sr ratio, S34S of pyrite, and whole-rock S18O. The most useful vectors for pyritic Cu-Au ores are AI, CCPI, S/Na2O ratio, Na content of white mica, and Fe content of carbonate.

Jan 1, 2002

The history of mining is rightly proud of its achievements in improving productivity and cost improvements over the years. No matter what measure is used, tonnes per manhour, cost per tonne, etc vast improvements have been made over the last hundred years. In fact over the last ten years in Australian coal mines raw coal output per employee has increased by 60 per cent. When one examines why these improvements have taken place the principal reasons have been technological advancement in mining equipment, excavator and dump truck capacity increases, longwall and continuous miners continually improving in reliability and size. Of course all these improvements are correlated to an increase in capital cost. Even with the above-mentioned advances the pressure for increased performance is as strong as ever. The international mining and mineral-processing sector is currently operating in a recessive market with some traditional commodities, eg gold trading at 20 year lows. During recessive times senior management will demand greater returns on capital employed: the obvious choices being reducing costs or increasing throughput. In addition, head office environments will often place a capital freeze on operational management so the opportunity to take advantage of technological change is not available. The challenge is, therefore, to increase throughput and cut costs without the need for capital. The answer is to optimise the existing labour and plant. If done systematically a result in productivity improvement, in our experience, as high as 45 per cent can be achieved with the average across South East Asia and Australasia being 21 - 23 per cent. The intention of this paper is to present a systematic approach to labour and machine utilisation thereby gaining the greatest possible return on the existing capital base.

Jan 1, 1999

By V A. Tsukerman

Prospects a new energy saving method for an efficient destruction of the sturdy and hard materials (rocks, ores, frozen soils, concrete blocks, etc) û the Electric Pulse Discharge (EPD) method of materials destruction for green processing in mining and processing of mineral raw materials are considered.The EPD-technologies give additional possibilities for solving ecological problems at the expense of increase of integrated approach of utilisation of minerals and industrial wastes. The scientific and technical level of executed development of EPD method is sufficient for organisation of design work to develop substantially new equipment. A number of plants have been developed and tested, including plants for processing raw material with minerals of jewels, plants for selection of mica from rocks, and plants for processing the merging of artificial mica.

Jan 1, 2002

By S Bourke, R Stone, B Hill

Since Jameson Cell flotation technology was first installed in a coal flotation application in 1988/89 at Newlands Coal Handling and Preparation Plant (CHPP) there have been fundamental improvements to its design which has led to its current status as the leading technology in Australia for fine coal flotation. These improvements, which include key hardware modifications, consist of the re-development of the orifice plate to produce considerable increase in wear life and reduction in power consumption for a given air entrainment and a significant increase in the amount of air that is entrained. Modifications to the downcomer allow maximisation of residence time and air entrainment while changes to the feed and air distribution system allows a reduction in installation cost and a reduction of solids ingress into the air line. Additionally, operational improvements such as the use of recycle to maintain constant flow to the cell feed are discussed. The recent installation at Hail Creek in the Bowen Basin, which consists of three B6000/20 Jameson Cells (6 m diameter bottom-fed distributor with 20 downcomers) will be reviewed as a case study. The latest design and operability of the cells are summarised and compared against one of the original designs at Riverside CHPP also in the Bowen Basin.

Jan 1, 2005

By Hargraves A. J

With increasing depth, stresses and stress phenomena are becoming more important considerations in Australian coal mining.A large number of compressive and tensile strength tests was made on coal and rock cubes cut from samples taken in various Australian collieries. In addition, an empirical impact strength test was carriedout on fragments of the same samples, to obtain a correlation with compressive strength.In one colliery, flat-jack measurements were taken to assess stresses in coal ribs and in the roof.INTRODUCTIONBy world standards, some of the New South Wales collieries are approaching depths of cover considered a maximum for bord and pillar the normal Australian coal mining method. Several South Coast collieries are winning coal at depths of about 1500 ft., and future operations are being planned at deeper cover. Some areas of these deep workings produce considerable quantities of seam gas.Phenomena associated with high stress and copious gas under pressure in the seam violent phenoma presenting a danger and a nuisance in mine working - have occasionally occurred, and the phenomena are being investigated as a whole (Hargraves, 1958), and separately as a gas problem (Bolt and Innes, 1959; Hargraves, 1962) and as a stress problem. This paper relates to the latter - to investigations into the strengths of coals and coal measure rocks, and into the stresses in and about coal seams...

Jan 1, 1962

By F E. Grader

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effectiveness of separation depends on the energising current of the separator, the frequency of the ac cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150 ¦m +74 ¦m) on the linear motor surface has been observed using a cine camera. An attempt, has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an ac cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear motor surface.

Jan 1, 1980

By A Giblett, K Afewu

This paper uses a case study to demonstrate best practices techniques for predicting the contribution of gravity concentration in a gold recovery process flowsheet. The case study was selected as an example of an ore with a marginal gravity gold content, which makes the value of a gravity circuit difficult to quantify. In this instance the value of leveraging a significant knowledgebase of operating gravity circuit performance to support the decision making process was demonstrated. This case study analysis serves as a useful demonstration of best practice methodologies supporting decisions to include or exclude gravity recovery in a gold recovery process flowsheet.CITATION:Giblett, A and Afewu, K, 2015. Do we need a gravity circuit or not? A case study in applying best practice, in Proceedings MetPlant 2015, pp 288–295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The State of New South Wales is highly favoured in having vast deposits of coal adjacent to and within easy reach of the coastal Ports. Not only is the quality of the fuel generally superior to any found in the other States, but it is greater in extent than in any other part of the Continent. For interesting and reliable details of the history of the discovery of coal, the geology of the coal bearing strata, analysis of the various coals and other valuable data, the readers are referred to the book recently issued by the New South Wales Government, entitled The Mineral Resources of New South Wales, by Edward F. Pittman, A.R.S.M., etc., by the direction of the Hon. T. L. Fegan, Minister for Mines. The mining community is indebted to the Minister for having had published the most valuable condensed record of the mineral resources of the State extant.For the purposes of this paper we will only give such a general description of the coal fields as will make it intelligible in connection with the subject of the coal mining in the State of New South Wales.

Jan 1, 1904

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

By M L. van Kampen

The Resource Management Act 1991 provides for activities to be classified as permitted, controlled, restricted discretionary, discretionary, non-complying or prohibited in district and regional plans. This paper looks at the use of the prohibited activity status to restrict, in particular, mining. Often the use of prohibited activity status for mining appears to have no basis other than the negative perceptions that the local community and/or the planner drafting the plan has toward mining and quarrying.   The paper will address the current appeal regarding the use of prohibited activity status now before the Court of Appeal, and the history to the litigation. The relevance of the outcome of the appeal to the minerals sector will also be explained.

Jan 1, 2007

In referring to two subjects of interest to the Members of this Australasian Institute of Mining Engineers, I would at the outset desire to express our gratification that to-day we are able to welcome as now united with ourselves, those members who until recently constituted the New Zealand Institute. It is hoped that the amalgamation so amicably arranged may be productive of the best results to all concerned, incorporated as this combination has been at the moment of the fulfilment of that greater political union, the Australian Commonwealth.Since last Annual Meeting held in Brisbane, we have come under the same roof as the Chamber of Mines of Victoria, and we entertain the hope that as that Chamber and this Institute possess so many interests in common in the encouragement and advancement of mining and metallurgical progress in these colonies, that much mutual benefit will ensue. There are many directions in which each body can assist the other, and I trust that a friendly co-operation will be maintained.It is gratifying to feel that in all the colonies a distinct movement is being made to increase the facilities for education in Mining and Metallurgy but if I may refer to our colony of Victoria in particular, we have to express the profound regret that in the means of education in the higher branches, we occupy an inferior position, and it is quite certain that we will continue to do so unless the Government is prepared to subordinate provincial considerations to the weightier.

Jan 1, 1901