Search Documents

By E. P. Mathewson

THE experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal "barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-1b. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly verti¬cal, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are appar¬ent, and the irregularities of the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., II and III, which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table II with a converter that had made three charges and had been cleaned out; that of Table III with a converter that bad blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows : Cu, 59.9;

Jan 1, 1907

By E. Buehler, R. H. Willens

A Hew melting technique has hem adapted to the rapid quenching of- alloys from the liquid state. The inelting method has no limitations on the alloys investigated for there is no reaction with crucible materials and the most refractory materials are easily melted. The vate of heating is so rapid that alloys which have a high vapor pressure constituent can be melted with a minimal loss in material. Several new superconductovs have been discoveved by vapid quenching of lolten alloys. THE rapid quenching of alloys from the liquid state has led to the discovery of many new metastable phases. The methods initially used were limited to alloys which did not react with crucible materials.1,2 There was also the unmentioned limitation in tem- perature. Alloys with melting points much greater than 2000°C could not be melted in the rapid-quench apparatus. Recently, there have been successful attempts to rapidly quench reactive alloys by Moss et at. and Matthias Moss et al. injected powdered material (325 mesh) into a high-temperature plasma and the high-velocity molten droplets impinged on a cooled copper plate. The technique innovated by Matthias was to melt the alloy in an arc furnace and splatter it against a copper plate by means of a high-velocity gas jet aimed at the melt. I) FAST COOLING APPARATUS The creation of a metastable phase in a given alloy system by rapid cooling from the melt is contingent on the quenching rate. Some alloys require very slow rates while other alloys require the ultimate in quenching rate. At the present time, the vertical-gun technique of Duwez and willens' has demonstrated, in practice, the highest quenching rates and thus the best

Jan 1, 1967

By John V. Beall

When a mine has ore averaging 5% lead, 7% zinc, 0.60% copper, 1/4 oz gold, and 6 oz of silver, adequate reserves, power and water, easy access to market, and is situated in beautiful natural surroundings with the advantages of a big city within a few hours drive, there is little left to be desired. Such a mine is the Mayflower mine of the New Park Mining Co. situated 30 miles from Salt Lake City in the Wasatch Mountains near Keetley, Utah.

Jan 1, 1949

By John V. W. Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese, but taking into consideration the diminishing quality of iron ores and fuels as well as the increasing exaction of specifications for finished products, it may safely be assumed that, high-grade manganese ore will be more and more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits. Sources of Production Russia alone, of countries producing the major part of the world's stee1, has within its geographical boundaries sufficient manganese to supply its needs. The domestic production of England is inadequate and English requirements for high-grade manganese are supplied principally from India. France also draws largely upon India, as it depends upon foreign sources of supply except with respect to a small tonnage of silico-manga-nese and silico-spiegel produced in the Hautes-Pyrénées. Germany and the United States likewise depend upon foreign sources of high-grade ore, though each possesses comparatively large reserves of ferruginous manganese ore and manganiferous iron ore. At present the world demand for high-grade manganese ore is met with ease by the production of Russia, India, Gold Coast and Brazil.

Jan 1, 1927

By Joseph J. Becker

RECENTLY the "oriented growth" hypothesis of recrystallization textures has been receiving considerable attention. According to this view, "whenever a new generation of grains is growing in a highly oriented matrix . . . one may assume . . . that from among available nuclei of a great variety of orientations those with suitable orientation relationship with respect to the matrix have by far the highest rate of growth (oriented growth) and will, therefore, predominate."' This statement includes primary recrystallization of single crystals and of polycrystalline materials showing strong deformation textures as particular cases. While the phenomenon of oriented growth undoubtedly does operate, and may be of importance in coarsening or secondary recrystallization, the writer feels that its extension to primary recrystallization is a different matter. Several aspects of this phenomenon may be pointed out which are difficult to rationalize on the basis of oriented growth. In recrystallizing deformed single crystals of alpha brass, Maddin, Mathewson, and Hibbard2 found that the twin composition planes of the recrystallized grains were parallel to the three operative slip planes they observed, and not to the fourth octahedral plane. The writer's current work seems to indicate further that when only one or two slip systems can be seen to operate, the recrystallized grains are aligned only with those slip planes actually observed. This behavior could hardly be accounted for by oriented growth, because on the latter basis the recrystallized texture of a deformed single crystal should certainly have the same symmetry as the crystal itself. Growth rates could not be expected to distinguish between crystallogra- phically equivalent directions, unless the presence of a visible slip system vastly increases the growth rate in the appropriate direction. This seems unlikely. These relationships were observed by the writer only when considerable care had been exercised before annealing to etch away the effects of cutting out the centers of tensile specimens with a jeweler's saw and to etch off the ends of compression specimens. When these.precautions were not taken, nu-cleation inevitably appeared to occur at the saw cuts or at the ends, and the resulting orientations never showed a [111] rotation but appeared quite random. The provision of many nuclei of many orientations did not enhance the correlation, but destroyed it. Recrystallization textures are sometimes strongly dependent on annealing temperature, which would imply that the anisotropy of growth rates is a suddenly varying function of temperature. This might be regarded as unlikely. Recrystallization textures can be strongly dependent on the degree of deformation. If textures are to be explained by selective growth from among nuclei of all orientations, it is difficult to see how the recrystallization process could have any dependence whatever on the manner or degree of deformation. It is felt that the above points should be considered before the oriented growth hypothesis is applied to primary recrystallization, with the necessary complete divorce of the mechanism of recrystallization from the details of the deformation process. References 1P. A. Beck and H. Hu: Reply to discussion of their paper on Recrystallization Texture and Coarsening Texture in High Purity Aluminum. Trans. AIME, 188, 1057; Journal oF Metals (Aug. 1950) TP 29083. 'R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins in Brass. Trans. AIME, 185, 655; Journal of Metals (Sept. 1949) TP 26763.

Jan 1, 1952

By Theron Wasson

During 1936 the state of Michigan produced 11,868,573 bbl. This is approximately 4,000,000 bbl. less than produced in 1935. The principle reason for the decrease in production over the previous year was the rapid decline of the Crystal field, which reached its peak in October 1935. The old producing area—Mt. Pleasant, Porter, Yost-Clark— accounted for over 7,000,000 bbl. during 1936. Crystal produced a total of 2,400,000. Outstanding among the old fields were Vernon and

Jan 1, 1937

By R. F. Pilgrim

A digital computer program to mathematically simulate the effect of limited changes in feed rate in the range of 80 to 95 tph on a plant-scale wet grinding circuit has been developed and tested. The circuit studied included an 8-ft-diam X 12-ft rod mill operating in open circuit and feeding two parallel 12-ft-diam x 10-ft pebble mills, each one operating in closed circuit with an 8 X 32-ft rake classifier. The simulation is an empirical one based on two sets of data collected manually from the operating circuit under what was said to be steady-state feed rates of 80 and 95 tph with all other operating variables also at steady state. The procedure is a combination of several published approaches to the modeling of grinding mills and classifiers and it is applicable to a wide range of circuits. The program permits the computing of the size distributions of all feeds and discharges of all grinding units and classifiers in the circuit for a specified feed rate. The data used in this report for demonstrating the program are unsatisfactory since the circuit was not operating under steady-state conditions when it was sampled. Consequently the circuit model parameters could not be accurately estimated. The predictive power would be greatly improved if new data were obtained under true steady-state conditions.

Jan 1, 1973

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.' At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.' They investigated the inflammability of certain magnesium alloys. Brown3-' reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.' These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952

By E. DeGoyler

The Furbero oil field lies in the Gulf coastal plain of Mexico between the important ports of Tampico and Vera Cruz and about one-third of the distance between the two points from the latter (Lat. 20" 22' N., 97" 30' W. Gren.). It is in the State of Vera Cruz, about 14 miles west by south of the village of Papantla in the canton of the same name, and is the most southern of the developed oil fields of the Tampico-Tuxpam region being a distance of 50 miles south by east from the Potrero del Llano field and 42 miles in the same direction from the Alamo field. The field has been developed by the Oil Fields of Mexico Co. and is in the midst of a large block of lands owned or leased by them. Communication is through the port of Tuxpam with which it is connected by a narrow-gauge railway and 6-in. pipe line some 52 miles in length. This field is of more than ordinary interest since it represents a type of oil deposit hitherto unknown. So far as I am aware, no other commercially valuable deposit of oil is known to occur under conditions of accumulation similar to those found here. The igneous nature of the so-called 'sand' encountered in drilling was not recognized until a number of wells had been drilled; and it was not until recently that the geological relations of the sill or laccolith, which gives rise to the accumulation of oil, were known and the so-called 'anticline' was known to be, in part at least, the result of igneous intrusion. Geological surveys in this general region were made in 1900-1901 by W. H. Dalton and in 1907-1909 by P. C. A. Stewart, F. W. Moon, Leonard V. Dalton, and Dr. Max Muhlberg. More recent surveys have been made, however, under the direction of the author, by E. L. Ickes, B. C. Belt, B. Hartley, and Harve Loomis. Notes of the earlier examinations were not available with the exception of the report by Dr. Muhlberg who apparently first recognized the true nature of the Furbero intrusion. This paper is indebted to his work and that of the more recent surveys for much of the detail regarding stratigraphy and to Messrs. Percy Furber and Arthur C. Payne, President and General Manager of the Oil Fields of Mexico Go. for permission to publish, and for much of the in-

Jan 1, 1916

By J. Gordon Parr, D. H. Polonis

High purity alloys of titanium and iron, made by a technique of levitation melting, have been investigated with particular reference to martensite formation and decomposition in the hypoeutectoid range. A preliminary study has been made of the occurrence of the phase corresponding to the structure Ti2Fe. MANY of the previous investigations of Fe-Ti alloys have been made using Kroll sponge as a source of titanium; and the subsequent heat treatments to which alloys have been subjected has, on occasion, led to further contamination. Worrier,',' who suggested a part of the equilibrium diagram for the binary system, and Wallbaum and coworkers,3-5 who worked largely with iron-rich alloys, all used Kroll sponge. Van Thyne, Kessler, and Hansen,6 in their determination of the equilibrium diagram, used iodide titanium for alloys up to 30 pct Fe. Duwez,7 who measured the M. temperature of titanium binary alloys with many solute elements, used iodide titanium in all cases except in his work on Ti-Fe alloys for which he used Kroll sponge. The investigation of the supposed phase Ti2Fe by Rostoker8 nvolved the use of iodide titanium. A section of the constitutional diagram, after Van Thyne et al., is reproduced in Fig. 1. Frequently too much stress is placed on the effect of contaminants in equilibrium and nonequilibrium systems, but there is no doubt that titanium alloys are extremely susceptible to interstitial atoms. Consequently, the main purpose of the work to be described was to determine those features of phase transformations in pure Ti-Fe alloys that were considered of importance in commercial heat treatments. For, although commercial alloys may not be of high purity, the investigation of a system uncomplicated by traces of impurity is a desirable starting point. Another incidental feature, the occurrence of Ti2Fe, was also investigated. The entire study was carried out using powders obtained from alloy ingots, for diffusion reactions are often more rapid in small particles than in bulk specimens. The frequently adopted practice of ascertaining phase constitutions by X-ray analysis of powders, and relating these to the microstructures and mechanical properties of bulk specimens, is considered by the authors to be open to criticism. In the martensite reactions in the Fe-Mn system, for example, it has been shown- hat similar phase distributions in solid and powder may result in different hardness values and appearance under the microscope; and it is possible that similar anomalies might occur in the Ti-Fe system. Consequently, in order to

Jan 1, 1955

By Frank C. Greene

Drilling in Missouri in 1939 was marked by wildcatting in the northern half of the state. The total completions numbered 82, exactly half the 164 of 1938. There were 15 gas wells with an initial open flow of 6,383,150 cu. ft., 4 oil wells with about 40 bbl. initial production, and 63 dry holes. The wildcatting followed the widely publicized leasing activity in the Forrest City Basin in northwestern Missouri, northeastern Kansas, southeastern Nebraska and southwestern Iowa. It is worth noting that

Jan 1, 1940

By Frank C. Greene

Drilling in Missouri in 1939 was marked by wildcatting in the northern half of the state. The total completions numbered 82, exactly half the 164 of 1938. There were 15 gas wells with an initial open flow of 6,383,150 cu. ft., 4 oil wells with about 40 bbl. initial production, and 63 dry holes. The wildcatting followed the widely publicized leasing activity in the Forrest City Basin in northwestern Missouri, northeastern Kansas, southeastern Nebraska and southwestern Iowa. It is worth noting that

Jan 1, 1940

By J. E. Elliott, K. O. Miller

Solubility studies were carried out to establish the phase distributions for various Fe-Ni-Pb-C alloys at temperatures where the metallic components exist as liquid solutions. Temperature us composition diagrams for the Ni-Pb, Fe-Pb, Fe-Ni-Pb, and Ni-Pb-C systems are derived by employing various approximations in conjunction with the data. Results are summarized for 1550°C in a quaternary phase diagram of the Fe-Ni-Pb-C system. BECAUSE surprisingly little information has been published on the phase diagrams of the Ni-Pb, Fe-Pb, Fe-Pb-Ni, and Fe-Ni-Pb-C systems, a study of these systems was undertaken to ascertain the important phase relationships in the temperature range of 1300" to 1550°C. Measurements were also made on the carbon-saturated systems in the hope that they would assist in the interpretation of the systems without carbon. This paper reports the results obtained from the simple equilibration of the various liquid and solid phases. EXPERIMENTAL PROCEDURE The experimental technique involved holding appropriati quantities of the metals in an alumina crucible, or in a graphite crucible when saturation of the melt with carbon was desired, for sufficient time at the desired temperature to ensure equilibrium. Then a sample of each liquid phase presen was drawn into a small-bore silica tube. This sample was withdrawn quickly from the furnace, cooled, and sent to the chemical laboratory for analysis. The cell assembly used is shown in Fig. 1. Durin the work on the Fe-Pb-Ni system, it was placed in a furnace wound with 20 pct Rh-80 pct Pt wire. This furnace eventually failed and subsequent studies were carried out between 1350" and 1475°C in a tube furnace heated by silicon-carbide resistance elements. A protective atmosphere of argon with approximately 10 pct hydrogen was supplied to the cell assembly at a gage pressure of 1 in. of water. Hydrogen was passed over palladized alumina and then anhydrous calcium chloride for purification. Argon was purified of oxygen and water vapor by passing it over copper gauze at 550°C and then through a calcium chloride drying column. The gases were mixed and redried before they entered the equilibration cell. Temperature was measured by calibrated Pt/Pt-10 pct Rh thermocouples and a Rubicon Type B potentiometer. The thermocouples were standardized against the melting points of pure nickel

Jan 1, 1961

By Edward Keller

(Canal Zone Meeting, November, 1910.) UNDER the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which was described how multi-manipulations, in a works-laboratory, and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit in, or withdraw from, a muffle a set of 48 cupels as one unit. The front row. (8) of these. are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cupels. This operation is an enlargement of what I have already described in my former paper, and Fig. I shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath was designated as being convenient, but was not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders may be removed from the boiling bath, and the acid or water poured off from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Fig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper. ' Trans., xxxvi., 3 to 18 (1906).

Aug 1, 1910

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By Louis A. Panek

INTRODUCTION AND SUMMARY With respect to the geomechanics aspects, the primary technical objectives in mining by an undercut-cave method are to achieve a controlled, sustained caving of the mineral body and to remove the fragmented ore with a minimum of dilution from surrounding unmineralized rock, while maintaining stability or control of the rock structure around the access openings. The structurally ideal ore body probably does not exist. If the rock mass is so weak as to cave on a short span, it may tend to be too sticky for easy drawing and handling, or create special problems in regard to support of the access openings. If the ore is strong, caving may be difficult and the caved fragments may be of such a large size as to require special equipment for transferring the ore from the caved zone. Given enough time and money to generate data and conduct trials, engineering and ingenuity can devise an appropriate combination of mine layout, sequence of extraction, and mechanical equipment to achieve a technically successful caving extraction operation to meet the foregoing requirements in many types of deposits. The large capital investment involved, however, reduces the freedom to make major changes once the mine development is well under- way, and the penalties for failure to accurately anticipate operating conditions militate against selecting any but the most obvious candidates for mining by an undercut-cave method. The demonstrated capability to extract large, deep, economically marginal deposits by this low-cost, high-volume method of mining provides an incentive to develop a rationale for predicting the cavability and stability characteristics of a deposit prior to mining, so that the undercut-cave method may be extended to a much wider range of mineral deposit characteristics. The ultimate goal is to establish as explicitly as possible the quantitative interrelationships between the measured rock-mass characteristics, the caving span, the size distribution of caved ore fragments, and the sizes and locations of stable access openings. Lacking an understanding of these relation- ships, a designer may readily change some factor in the wrong direction (e.g., excessively reduce the distance between the extraction level and the undercut to increase the convenience of operations for the undercutting crew, increasing the frequency of repairs to the extraction-level support system) or create unnecessary problems elsewhere in the system by introducing a design change that can achieve only minimal improvement in the factor of direct interest (e.g., unnecessarily complicate the ore-transfer system by changing the orientations of the openings, with- out succeeding in the objective of improving the ground support conditions). Although successful predesign is the prime objective, subsequent modifications in mine lay- out and sequence of extraction operations are inevitable. In developing the modified solution, systematic experimentation based on an understanding of the underlying structural relationships, coupled with monitoring measurements of selected diagnostic structural-behavior parameters, can achieve an acceptable solution in a minimum number of steps, which is far superior to the typical operational trial-and-error approach, in view of the cost of implementing each successive change. Since a drill-core sample of ore rock from a successful undercut-cave operation may exhibit a uniaxial crushing strength in excess of 100 MPa, the caving of such a rock mass is now commonly believed to be ascribable to the presence of discontinuities such as joints or fractures throughout the ore body. An essential part of the present investigation was therefore to characterize the natural discontinuities at each of the test sites by measuring their attitudes and spacings. The term "fracture" is used herein in a general sense to include any planar discontinuity without implication as to its suggested mode of origin. Most, but not all, of the fractures are properly termed joints. As a point of departure we may consider the possibility that the rock mass is transected by three families of joints, each family possessing a distinct orientation, such that parallelepipeds of intact rock are delineated by the jointing. Even if cementation is absent between adjoining parallelepipeds, the undercutting of the rock mass will not necessarily initiate sustained caving--owing to the all-around confinement, an arch may tend to stabilize over the undercut unless prevented from doing so by the failures of key blocks of intact rock. Thus, although the jointing can be assumed to weaken the rock mass, creating preferred directions of

Jan 1, 1981

By Martin Coryell, Eckley Coxe, R. P. Rothwell

WILKES-BARRE, PA., April, 1871. THE great development of the mines and metallurgical works of this country during the last few years, accompanied as it has been by the investment of enor¬mous sums of money in purchasing lands, and in the erection of improvements, requires that advantage should be taken of the accumulated knowledge of engi¬neers, superintendents, and others, in mastering the problems which are con¬stantly presenting themselves for our action. Among those may be mentioned the consideration of more economical systems of mining in our coal and metal¬liferous mines, improved methods of transportation above and below ground, unwatering and ventilating mines, the mechanical preparation of coal and other minerals, the various metallurgical processes, and, in fact, every question tending to the attainment of two great objects 1st. The more economical production of the useful minerals and metals. 2d. The greater safety and welfare of those employed in these industries. In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed as the free interchange of experience among those actually engaged in these industries, and this object has been accomplished, mainly, through the medium of institutes, associations or societies, composed of those engaged in these occupations, and by the- periodical publication of essays or papers, communicated to such societies by their members. It must be evident to all practical men that the interchange of the varied experience of those engaged in such occupations in this country could not fail to advance very materially the desired objects; it is, therefore, proposed to establish an American Institute of Mining Engineers, which will hold its meetings periodically in the great mining and metallurgical centres, where works of interest, such as mines, machine shops, furnaces, and other metallurgical works, can be inspected, and the members exchange their views, and consult for mutual advantage upon the difficulties encountered by each; these transactions or proceedings, when published, would form a most valuable and greatly-needed addition to our professional literature. It is proposed that a meeting of those sympathizing with the object above men¬tioned shall be called for the purpose of organizing such an association, the place and time of meeting being Wilkes-Barre, Pa., and the month of April or May. Communications indicating the opinion and wishes of all, both as to these points, and also as to the organization and objects of the Institute, will be gladly received by any of the undersigned, and a notice of the date of meeting, which will be arranged to suit the greater number, will be duly communicated. Any

Jan 1, 1873

By Robert L. Akre

When Marco Polo visited China in the 13th century, no one knew what black powder was except the Chinese; they knew enough to make dazzling fireworks with it. But the realization that black powder could also do useful work came much later and, like all important discoveries, it altered the course of history. It was in the 14th century that black powder was first used to break rock in a very crude way; there were no drills and the powder was simply poured into cracks and exploded by setting it afire. Because its energy value was pretty low, the need for something more powerful was felt when the industrial revolution began. In the 1850s, miners began experimenting with liquid nitroglycerine on a limited scale. This was a very sensitive and dangerous explosive. Fortunately in the 1860s, Alfred Nobel succeeded in stabilizing nitroglycerine by absorbing it in kieselguhr-and a new product, dynamite, was born. With it, miners were able to unleash the great energy of nitroglycerine for blasting purposes. But dynamite was still a very sensitive explosive. In subsequent years, other explosives of various strengths and characteristics were developed, such as blasting gelatin, gelatin dynamite, ammonia dynamites, (all containing some nitroglycerine or nitrostarch), and liquid oxygen explosives. These products and their variations supplied the blasting trade for many years. A grained ammonium nitrate product containing some carbonaceous material entered the market in the 1930s. This explosive had below-zero sensitivity-meaning: a No. 6 blasting cap imbedded in it would not detonate it. A more sensitive initiator, called a primer, was needed to detonate this mixture. From Rags to Primacord to Solid-State The first initiator for an explosive charge was probably a rag slowly burning its way to the charge; this method was quite unreliable. Then came the burning fuse, which was an improvement. Next was the nonelectric blasting cap initiated by a fuse. With these initiators, a miner needed quick reflexes and good legs; upon lighting the fuse, he had to run immediately for cover. Development of the electric blasting cap that allowed for accurate timing eliminated this hazard; the electric cap, however, introduced other safety problems because of its susceptibility to extraneous electricity, e.g., ground currents, lightning, and static electricity. These caps also became available in millisecond delays. Development in the mid-1930s of Primacord, a detonating fuse insensitive to electrical currents or impact, further reduced blasting hazards, and is generally acknowledged as the safest known means of initiation. Eventually, Primacord millisecond connectors also became available for delay patterns in blasting. In the mid-1960s, the Primadet delay was introduced; it is a practical nonelectric detonator system that offers the precise timing of electric blasting caps-and is immune to the hazards or effects of extraneous electricity. Recently, Research Energy of Ohio, Inc. introduced a new type of solid-state blasting machine that combines a sequential timer and delay caps. It enables the efficient breakage of rock with a minimum amount of shock, ground vibration, and noise. Improvements in Blast-Hole Drilling World War II created an enormous demand for coal and other minerals in the U.S. and elsewhere. Great efforts and large amounts of capital were spent to find new mineral deposits and develop better mining methods. But while mechanization in mining proceeded at a rapid pace particularly in open-cut work, there was a definite lag in developing new or improved machines for drilling blast holes. The industry continued to depend largely on horizontal, churn, and pneumatic drills. No better machine was available for large scale production. The need for improvement in this phase of mining became more acute in the post-war years. Despite efforts toward further mechanization, mining costs rose rapidly because of mounting inflation and increasingly high wages. In most operations, drilling and blasting the overburden became the principal item of cost. Therefore, whatever size holes were being drilled, the holes had to be spaced so that any foot of the bore hole could be loaded with the maximum load required for the number of cubic yards of material that each foot of the hole was carrying. With the smaller holes that were being drilled, the proportion of drilling cost to the total drilling and shooting cost was much higher than it would have been with larger holes (because of the closer spacing required by smal-

Jan 1, 1977

By E. T. Turkdogan

The activity of sulfur was determined as a function of composition of ferrous sulfide by equilibrating with hydrogen sulfide-hydrogen gas mixtures at 670° , 800°, and 900". The present results supplement the available data over the composition range from 36.6 to 39.5 pct S. The X-ray lattice spacing measurements made are in accord with the available data and indicate that the limiting composition FeSl.008 may be taken for the iron-iron sulfide equilibrium. The growth rate of ferrous sulfide on iron was measured by reacting iron strips or blocks in hydrogen sulfide-hydrogen gas mixtures. Owing to the slow approach to equilibrium between the gas phase and the surface of the sulfide layer, The sulfidation experiments were carried out for several days. It is shown that the growth rate ullimately proceeds in accordance wilh the parabolic rate law. From the parabolic rate constants and the thermodynamic data on iron sulfide the self-difiusivity and chemical diffusivity of iron in ferrous bisulfide are evalualed. The self-diffusivity of iron thus derived zs found to increase with increasing sulfur content. THE ferrous sulfide known as "pyrrhotite" is a non-stoichiometric phase having a wide composition range from about 50 to about 58 or 60 at. pct, depending on the sulfur activity. RosenQvistl studied the thermodynamics of this phase over wide ranges of temperature and composition. Hauffe and Rahmel' and Meussner and ~irchenall~ studied the parabolic rate of sulfidation of iron in sulfur vapor. By using markers, these investigators showed that the iron cations were the predominant diffusing species in iron sulfide. This is confirmed decisively by the self-diffusivity measurements of condit4 who showed that the self-diffusivity of sulfur in ferrous sulfide is several orders of magnitude lower than the self-diffusivity of iron. Although much has been learned from these studies about the Fe-S system, further research on this subject was considered desirable for better understanding of the physical chemistry of iron sulfide. This work was confined to the study of the kinetics of sulfidation of iron in hydrogen sulfide-hydrogen gas mixtures. The results of this study are given in two consecutive parts. Part I, the present paper, is on the parabolic rate of sulfidation of iron and the diffusivity of iron in ferrous sulfide. The second paper, Part 11, is on the kinetics of the surface reaction between hydrogen sulfide and ferrous sulfide. EXPERIMENTAL Three types of experiments were carried out: i) equilibration of ferrous sulfide with gas of known E. T. TURKDOGAN, member AIME, is Manager,Chemical Metallurgy Division, Edgar C. Bain Laboratory for Fundamental Research, U. S. Steel Corp., Research Center, Monroeville, Pa. Manuscript submitted March 6. 1968. ISD sulfur potential; ii) X-ray studies of ferrous sulfide; and iii) measurements of the parabolic rate of sulfidation of iron. Equilibrium Studies. About 1 g of iron powder or foil. contained in a small recrystallized alumina crucible ind suspended from a calibrated silica spring, was reacted with a hydrogen sulfide-hydrogen mixture of known ratio until no further change in weight was observed. %hen the gas composition was changed and the new state of equilibrium was established after several hours of reaction time. The composition of the sulfide was obtained from the initial weight of the sample and the weight after equilibration. X-Ray Studies. The lattice parameters of some of the equilibrated samples were determined using the General Electric XRD-5 diffractometer with a cobalt tube (no filter) set at 40 kv apd 10 ma; the CoK, radiation was taken as 1.79020A. Observed 220 and 311 diffraction peaks of silicon served as an internal comparison standard to correct for possible misalignment of the goniometer. The lattice parameters of the sulfide phase were calculated from the corrected Bragg angles of the 110 and 102 peaks. Rate Studies. In the initial experiments attempts were made to measure the parabolic rate of sulfidation by measuring the gain in weight of a thin iron strip, -0.05 cm thick, suspended from a silica spring in the reacting atmosphere. The preliminary experiments showed that this technique was not reliable for the measurement of the parabolic growth rate of the iron sulfide layer. In the subsequent experiments the data on growth rate were obtained by measuring, on a microscope stage, change in the thickness of the sample after reaction for a specified time in a hydrogen sulfide-hydrogen mixture of known sulfur activity. For each reaction time a new sample was used. Precision-machined iron blocks, 0.5 by 2 by 5 cu cm, were de-greased and annealed in hydrogen for several hours prior to the sulfidation rate measurements. The experiments were carried out at 670°, 800°, and 900°C in gas mixtures having the ratios, and 1.0 for periods of times from a few hours up to 8 days. Apparatus and Materials. A vertical globar tube furnace with a 3-in.-long uniform temperature zone was used. The glass tube fittings were fused on the zircon reaction tube, 1.5 in. diam. The temperature was measured with a Pt-10 pct Rh/Pt thermocouple placed in the hot zone of the furnace inside the reaction tube (an alumina thermocouple sheath was used). A separate thermocouple was used for the temperature controller which maintained the furnace temperature constant within about 2°C. Anhydrous liquid hydrogen sulfide and oxygen-free dry hydrogen from gas tanks were used in preparing the gas mixtures by the constant head capillary flow-meters. In all cases volume flow rate was 1000 cu cm per min at stp, corresponding to a linear velocity of about 6 cm per sec at 800°C; under these conditions

Jan 1, 1969