Search Documents

By G. F. Loughlin

Nearly 55 years have elapsed since the U. S. Geological Survey was organized. During this period the mineral industries have grown from infancy or early childhood to well developed maturity, and some mining industries appear to be declining. Decline in mining is even more conspicuous in certain districts, or even states, than in any mining industry as a whole, and discoveries or developments of important new districts have been very few in recent years. Our reserves of most metals and nonmetals are adequate for many years of normal production, subject to changes in rate of exploitation that may be caused by foreign competition and by changes in technology and market conditions; but the declining production of many districts and the scarcity of important new discoveries to compensate for them is cause for some apprehension. It is likely that future production will depend to a considerable extent on deep exploration and on the thorough examination of places in and adjoining existing districts where significant outcrops are lacking and only apparently insignificant geologic features offer encouraging clues—more so than on the discovery of entirely new districts. Even the possible discovery of new districts, which have escaped the intensive search by the nontechnical prospector, must be dependent on geologic information. There is therefore no need for argument as to the value of geology to the mining industry; and the need of continuing to advance the science. The U. S. Geological Survey's past contributions to mining geology, as expressed in its official reports and other publications, are recognized by Ransome in his historical review of mining geology in the Lindgren volume.' These contributions have helped to form the basis of modern mining geology, which has grown rapidly in the last 25 years. This growth has witnessed the organization and maintenance of geologic staffs by mining companies in several districts, and their detailed work, together with the fact that nearly all of the larger mining districts have

Jan 1, 1935

By W. M. Rust, W. D. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimenlally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so universally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretatioils of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in. in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resist-

Jan 1, 1946

By W. M. Rust, W. D. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimenlally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so universally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretatioils of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in. in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resist-

Jan 1, 1946

By M. Schmellenkamp

By comparing two longwall operations, one begun in 1956 and the other in 1960, the author is able to demonstrate the increases in production and performance made possible by longwall mining. These achievements have been brought about by continuous development of longwall mining equipment and associated roof supports. Because of this progress, longwall mining is able to provide, under proper conditions, high production per man-shift, remarkable cost savings, dependable roof control, safe working conditions and truly continuous production. It may seem odd that the title of this paper is not simply "Longwall Mining" but instead "Progress in Longwall Mining." However, the word "Progress" definitely has its place in longwall mining. If it had not been for progress in the development of longwall mining equipment and roof supports, the longwall mining method would not be able to compete in production and performance with modem coal mining machines. The longwall mining method was practiced at the beginning of the century and there were several successful operations in coal fields in Illinois. In those early days of longwall mining, the coal was undercut by hand 2 to 2.5 ft at the bottom of the seam and packwalls were built in the gob to support the roof. The roof eventually subsided and the weight of the subsiding roof was used to ride the face and break the undercut coal. Utilizing natural weight to soften the coal face is still practiced in modern longwall mining; however, the packwalling method has been replaced by the caving method and the roof is now supported by yielding steel roof supports and forepoling steel headers. The purpose of these yielding-type roof supports is to provide a safe working area for the crew along the entire longwall face, to permit continuous mechanical mining across the prop free face, and to provide a strong resistance for the roof by forming an even breaking line at the gob for the roof to cave. Roof supports and associated forepoling headers should be kept as close as possible to the face in order to prevent a caving between face and supports, especially under friable roof. This means that the coal should be extracted in small slices, allowing only a narrow roof area to be exposed and unsupported. The coal planer with its relatively high cutting velocity of 75 ft per min provides such an extraction of coal and has proved its high performance under difficult mining conditions. Since 1951, several longwall faces in southem West Virginia and Pennsylvania which have been equipped with the coal planer and friction-type manual roof supports have been successfully operated. Compared to today's longwall mining, these longwall faces required such a large crew, primarily to handle the roof supports, that the actual high production per shift was charged with too high a labor cost, thereby decreasing the tons per man. Yet, even then the longwall faces outperformed the conventional mining system under the same conditions. In order to demonstrate the progress that has been made in the development of longwall mining, a comparison will be made between a longwall face in Arkansas which was installed in 1956 and a modemized longwall face started in 1960 in southern West Virginia. LONGWALL MINING IN 1956 The 320-ft longwall face was developed in a 32-in. thick coal seam near Greenwood, Ark. The method of mining the 320-ft coal block was the advancing system in which three entries on either side of the face were driven ahead of the advancing longwall face. The face was equipped with a coal planer and a Panzer conveyor; timbering was done with wooden timbers and cribs. The roof supports were set without any pattern. The crew to operate the planer and to handle the roof supports (timbers and cribs) consisted of 15 men per shift. During a period of approximately eight monthsof single shift operating time, the average tonnage produced in this relatively low seam amounted to about 263 tons of clean coal per shift. To show the development in the coal plow from then until now, it should be pointed out that the standard plow was used in this operation. The plow was equipped with rigid bottom bits which could not be adjusted if the plow started to climb, thereby leaving bottom coal to be recovered by pick hammers end causing delays in production. The height of the plow

Jan 1, 1963

By PAUL DYER MERICA

PAUL DYER MERICA, who has been awarded the James Douglas Gold Medal for his achievements in non-ferrous metallurgy, is a Hoosier, having been born at Warsaw, Ind., in 1889. His father, a clergyman and educator, was president of the University of Wyoming from 1908 to 1913. After graduating from the University of Wisconsin in 1908, young Merica (not yet twenty years of age) went to China, where he was professor of chemistry in Chekiang Provincial College, Hangchow, until 1911. He then went to Germany to s t u d y and was fortunate enough to receive his Ph.D. from the University of Berlin just a few months before the outbreak of the World War in 1914. Returning to America, his first position was as special investigator at the En¬gineering Experiment Station of the University of Illinois, but before the year was out he joined the staff of the U. S. Bureau of Standards as associate physicist. Since 1918, he has been superintendent of research for the International Nickel Co. His work during those years is excellently summarized in the following quotation from the statement of Zay Jeffries recommending him for the award.

Jan 1, 1929

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials; it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted.

Jan 3, 1918

By P. H. Griffin

WHEN a subject, such as the manufacture and service of chilled car wheels, as has been fruitlessly discussed for ten or fifteen years, it is difficult to revive interest and action by the mere repetition of statements and arguments that have been made before. And when a situation involves serious responsibilities for conditions that have grown up under circumstances beyond the control of any particular individuals or authority, it is even more difficult to deal with. But there is one phase of every subject that need not involve these particular points if presented in a, proper manner; and that is, " the future state." I will try to present the subject of this communication from the latter standpoint and with the hope that all of those interested will feel disposed to give the matter attention from the basis that it is a, vitally important one to all that travel on railroads, whether as employees or officials, or as dependent on those in charge of the operation, or in the matter of materials and equipment used. The conditions of chilled wheel service have been changed so radically in the past ten or fifteen years by the use of freight cars of 40 and 50 tons capacity, that it is fair to say in the interest of all concerned in the use and in the manufacture of such wheels, that the increased strains and loads have been quite sufficient to account for much of the service results that have transpired. That proper provision was not made for increased possibilities of strength and wear, in fact that previous factors of the kind were allowed to deteriorate, is no proof that such wheels cannot be made equal to heavy service conditions as shown in the data given herein.

Jan 10, 1913

By Allen D. Gorrison

EFFORT to develop fundamental quantitative information and improved technique in the production of petroleum has long been faced with difficulties of a particularly evasive nature, owing to a combination of circumstances. In the first place, petroleum comes from far below the ground, out of sight, so that information derived from indirect observations must be extrapolated to reservoir conditions. If one does not force the analogy too far, the petroleum engineer may be said to be somewhat in the position of the astronomer. The actual phenomena which he wishes to observe in detail appear at a place so deep in the earth?s crust that personal observations and direct experiments are impossible.

Jan 1, 1942

By ARTHUR THACHER

PRIMITIVE man supplied his wants as they arose; as he became more civilized he anticipated them by producing more regularly and storing the products for future use. This tended to cheapen' production and prevent ' violent fluctuations and therefore tended to increase consumption. In order to anticipate our wants, we must know what these wants will be, and this can be .determined only by statistics. 'While we have made great progress in gathering statistics, they are still far from what they should be; especially metal statistics. We determine fairly, well the amount produced, but this does not answer all inquiries because of the erratic conditions of mining, it is necessary to carry larger stocks of metals than of most other articles; moreover, as metals are more or less durable, it is difficult to determine the actual consumption. We often count under consumption what is being produced and sold, while the actual consumption is what is being worn out.

Jan 1, 1921

By H. Ries

SPECIAL sands are those that are employed for special purposes. They have a limited use, as compared with sands for concrete and plaster. The sands discussed in this chapter are those used for foundry purposes, glass manufacture, filter beds, abrasive purposes, sandblasting, engine sand, sand for sheet asphalt, and furnace sand. These sands are almost invariably high in silica, consisting chiefly of quartz grains. In some-for instance, glass sands-freedom from ingredients other than silica, such as iron oxide, is important. Certain grades, like filter sand, require rather careful sizing, and in foundry sands the bond, usually clay, is important. One deposit may sometimes be used to supply several grades or types of sand by appropriate methods of screening and washing. The special sands discussed here are usually obtained from deposits of unconsolidated material but sands high in silica are derived occasionally from soft sand- stones that can be disintegrated easily. Requirements are not the same for all uses, and, while certain properties may be demanded, there are no officially adopted standard tests except for foundry sands. FOUNDRY SANDS Definition-Foundry sands include those siliceous sands that are used to make the forms for casting metals. If these are employed for making molds, they are known as molding sands; if for the cores that form the hollow spaces in the casting, they are called core sands. Naturally bonded sands are those containing a variable, though not usually large, amount of clay, which serves as a bond. Synthetic sands, now much used, represent an artificial mixture of sand with usually fire clay or bentonite. Core sands may be bonded with oil, cereal binders, resin, pitch, or other materials. The foundrymen apply the term "sharp sand" to one that is free from bond. Properties-The important properties to be tested at room temperature are texture or fineness, permeability, strength, deformation, and flowability. Those tested at elevated temperatures are compressive strength, expansion and contraction, sintering point, and durability. More attention probably has been given to research on the properties

Jan 1, 1949

By Sherwin F. Kelly, Bela Low, William B. Creagmile

Electrical methods and instruments for geophysical exploration have been almost exclusively applied, during these years of development of the art, by a few companies specializing in this field. The control of patents, the cost of the instruments and the general lack of published information on details of field procedure and office interpretation have given these owners a monopoly in carrying out electrical surveys. The development of the Megger Ground Tester1 seems likely to change this situation, and to enable mining engineers and geologists, without special training in geophysics, to carry out simple reconnaissance electrical surveys. Nevertheless, the need for such special training and experience in planning surveys and interpreting their results remains, and probably i always will remain, indispensable for a successful outcome. The unique thing about, the Megger Ground Tester, which gives rise to this hope for its general use, is its simplicity of operation. The four binding posts of the instrument are connected by insulated wires to four stakes driven into the ground at appropriate points. The crank of the Megger is then turned, and the resistance of the ground between the two inside stakes is read directly, in ohms, by the deflection of a pointer over a scale. The apparatus is shown in Fig. 1. Fundamentally, the principle of operation is that of determining the resistance of a four-terminal conductor, as applied by Frank Wenner to the measurement of earth resistivity. "A four-terminal conductor is a conductor provided with two terminals to which current leads may be connected and two terminals to which potential leads may be connected. The resistance of such a conductor is the difference in potential between the potential terminals divided by the current entering and leaving

Jan 1, 1932

By Loyd R. Kern

A procedure for determining the behavior of a reservoir under a gas or water injection program was reported by Buckley and Levertt in 1942.1 This method, which allowed the calculation of the phase saturation distribution behind the front of a displacing fluid, has been extended to apply to a more general situation. The reservoir may initially contain flowing quantities of the displacing fluid, or the fluid in the reservoir may be above saturation pressure SO that solution effects are present. Production may occur behind the front as in the case of a well which is produced after breakthrough of the displacing fluid. The calculating procedure is simplified in that the graphical integration necessary to determine breakthrough saturation is eliminated by performing a direct integration and the graphical differentiation necessary to determine saturation distribution is eliminated by representing the displacing phase fraction of the flowing stream by an empirical equation. This representation results in simple expressions for the producing gas or water/oil ratio and cumulative production. INTRODUCTION A method for the calculation of the saturation distribution behind the front (interface between the displaced and displacing phases in a gas injection or water flooding operation) was reported by Buckley and Leverett in 1942. The method leads to a curve for the saturation distribution which is double-valued; consequently, part of' the curve was interpreted to be physically meaningless. That part of the curve which has physical significance was determined by a graphical integra-tion (material balance). In this paper it is shown that the integration may be performed analytically with a resulting equation for the saturation of the displacing phase at the front. The case in which the displacing fluid is initially flowing and the case in which the reservoir is initially above the saturation pressure so that some injected gas goes into solution are included in the integration. The calculations are considerably simplified by representing the fraction of the flowing stream which is oil by an exponential function of saturation. The methods is extended to apply approximately to reservoirs in which wells located between the injection well and the front are produced. An illustrative example utilizing the methods presented is included. RESERVOIR BELOW SATURATION PRESSURE In the case of a water flooding operation or in the case of a gas injection operation in which no gas goes into solution in the displaced oil, the equation for saturation in a linear flow system as a function of time and position as given by Buckley and Leverett is where* q = total reservoir volume flow rate, rvb/day A = cross sectional area of system, sq ft / = porosity of formation x = distance from injection point, ft t = time, days Pj = saturation of the displacing phase /dx velocity of planes of constant saturation, ft/day *The nomenclature used here is not the same as that used by Buckley and Leverett A complete nomenclature is given in Appendix A.

Jan 1, 1952

By Ralph M. Hunter

Until recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged breakdown did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to bypass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdi-ness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, there- fore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 1946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1949

By G. S. Scott, G. W. Jones

ECONOMIC waste caused by mine fires may become considerable,15 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters-such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control. necessarily must be based upon one or the other, or both, of these two principles. . The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion) ; and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. OXIDATION OF COAL Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored.6,16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By J. M. Morris

The point to be made most clear in this paper is the economic value of flotation in the Benguet mill flow sheet. It is rather a statement of effect with no attempt at a technical explanation of the cause. Certain well-known, easily understood reagents, mechanisms and principles have been adapted to the conditions at Benguet, and have proved to be more successful than was demonstrated in the laboratory. The mechanical and metallurgical development of this particular operation was arrived at by trial and error, with fortunately very little error. Changes were slow, of necessity, which in the end proved a blessing in that time was afforded for observation and analysis of the disturbing factors; and as a result each change was a definite step towards higher efficiency. Many of these steps were unpredictable from laboratory work because of the varied and differing characteristics of ores met with in daily operation of the mill, which were practically impossible to reproduce on a laboratory scale. The Benguet mill receives daily ores that differ as much as if they were delivered from three different properties. There is first the surface and upper-level zone, which produces an oxidized secondary ore containing considerable iron oxide, manganese oxide and some organic matter. Formerly, most of this ore consisted of very soft fill with some hard rock mixed in. It also contained an unusual amount of iron and aluminum sulfate, which formed hydrates upon entering the alkaline cyanide solution and caused excessive frothing. When flotation was introduced in the Benguet mill the general characteristics of this upper-level ore had changed considerably, in that it was practically all newly mined, fairly hard ore. It still contained many of the same disturbing elements, but was somewhat simpler to treat than formerly. The small proportion of fines is still troublesome in flotation, and plant practice probably does not show more than 80 per cent extraction on this small portion of the ore. No definite figure on this is available, as this particular ore is delivered at irregular intervals

Jan 1, 1939

By J. M. Morris

The point to be made most clear in this paper is the economic value of flotation in the Benguet mill flow sheet. It is rather a statement of effect with no attempt at a technical explanation of the cause. Certain well-known, easily understood reagents, mechanisms and principles have been adapted to the conditions at Benguet, and have proved to be more successful than was demonstrated in the laboratory. The mechanical and metallurgical development of this particular operation was arrived at by trial and error, with fortunately very little error. Changes were slow, of necessity, which in the end proved a blessing in that time was afforded for observation and analysis of the disturbing factors; and as a result each change was a definite step towards higher efficiency. Many of these steps were unpredictable from laboratory work because of the varied and differing characteristics of ores met with in daily operation of the mill, which were practically impossible to reproduce on a laboratory scale. The Benguet mill receives daily ores that differ as much as if they were delivered from three different properties. There is first the surface and upper-level zone, which produces an oxidized secondary ore containing considerable iron oxide, manganese oxide and some organic matter. Formerly, most of this ore consisted of very soft fill with some hard rock mixed in. It also contained an unusual amount of iron and aluminum sulfate, which formed hydrates upon entering the alkaline cyanide solution and caused excessive frothing. When flotation was introduced in the Benguet mill the general characteristics of this upper-level ore had changed considerably, in that it was practically all newly mined, fairly hard ore. It still contained many of the same disturbing elements, but was somewhat simpler to treat than formerly. The small proportion of fines is still troublesome in flotation, and plant practice probably does not show more than 80 per cent extraction on this small portion of the ore. No definite figure on this is available, as this particular ore is delivered at irregular intervals

Jan 1, 1939

By A. E. Belton

The individual projections for large mines in the Pittsburgh coal seam in northern West Virginia are discussed with emphasis on roof control and ventilation requirements. All four mines use continuous miners with panel belts and rail for main line haulage. Both development and retreat-type mining are covered. There are a variety of mining projections being used currently in northern West Virginia. To discuss each would be impossible, so an arbitrary cross section has been selected in an attempt to indicate a fair degree of representation. Four mines, hereinafter referred to as Mines A, B, C and Dl will be discussed separately. The greater part of northern West Virginia coal production is mined from the Pittsburgh seam. This is the seam worked by all the mines discussed here. Although the coal bed outcrops at the eastern and southernmost points, these mines are all working in a depth ranging from 400 to 1400 ft below the surface. Some steep gracles have been encountered but are only considered local in nature; the overall average dip of the seam is 1 1/2 % northwest. In each of the operations the particular mining scheme used has proved advantageous, since they have been designed to satisfy particular equipment and/or physical condition requirements. So regardless whether such projections utilize a partial or full recovery principle, the productivity performances appear better than average. MINE A Full retreat is the basic mining approach for mine A, although current mining is primarily in the entry-driving stages to expand territory in preparation for pillar work. Only one section unit now on retreat. The average clean coal production at this mine is 7000 tons per day. Initially, a ripper-type miner was used for development at this mine. But with a rather weak roof overlying the coal bed and the greater horizontal span left at the top by a ripper machine, roof control became a critical problem. Even though roof bolts were used concurrently in the mining cycle for initial support, the majority of the roof in these entries

Jan 1, 1962

By J. K. Elliott, P. H. Kelly

Many engineering functions such as surface metering work and laboratory compressibility check points involve the use of liquid densities of light hydrocarbon mixtures at various pressures and temperatures. However, at the present time, no simple reliable method exists for determining density variation, particularly if the composition of the liquid is unknown. Consequently, a study was undertaken to develop and present a simple and accurate method of predicting density variation of a light hydrocarbon liquid with pressure and temperature, knowing only the density of the liquid at some condition. The experimental liquid compressibility data from API Project 37 by Sage and Lacey' have been considered to be accurate within 0.5 per cent and cover a wide range of pressure (14.7 to 10,000 psia), temperature (100" to 400°F) and molecular weight (up to 150). From these data, a set of liquid density curves, which relate density to pressure, temperature and molecular weight, was developed. These curves make it possible to predict density variation with pressure and temperature. Compared to extensive laboratory compressibility data on a complex, light hydrocarbon liquid, the use of the liquid density curves resulted in an average error of less than 0.5 per cent. Based on the results of this analysis, it is concluded that the set of liquid density curves developed from the data of Sage and Lacey provides an accurate and simple method for predicting the density variation of light hydrocarbon liquids when the density at some condition is known. These curves should be very helpful in many engineering calculations, particularly in the surface metering of light hydrocarbon liquids. INTRODUCTION Many situations arise in field and engineering laboratory work, such as reservoir engineering studies, check of experimentally determined laboratory data and orifice flow-meter formulas, where liquid density factors at various pressure-temperature conditions are required. Also, the need for accurate light hydrocarbon liquid information has become more important with the advent of miscible-type displacements for secondary recovery purposes in oilfield operations. Several reliable methods are available1 - "or determining the density of liquid hydrocarbons if the composition of the liquid is known. However, there is a definite lack of methods for accurately determining the variation of density when the composition of the liquid is unknown. The purpose of this study is to review the various methods for determining hydrocarbon liquid densities and to develop a simple and reliable method of determining variation in density of light hydrocarbon liquids with pressure and temperature when the compositio~n of the liquid is unknown. METHODS FOR DETERMINING DENSITY OF LIQUIDS OF KNOWN COMPOSITION Sage, Lacey and Hicks' have proposed a method to predict the density of light liquid hydrocarbons by using partial molal volumes. Data are available on experimentally developed partial liquid volumes of hydrocarbons over a rather limited range of temperature, pressure and composition. The partial mold volume method has proved satisfactory for determining the density of some hydrocarbon liquids when the composition is known. Within the range covered in the Sage, Lacey and Hicks1 data, the results agree within about 3 per cent of the experimental values. Hanson mentions the limitation of this method to a composition range of approximately 10 per cent by weight of methane, which will not allow this correction to cover most low molecular weight-light hydrocarbon liquids. Standing and Katz2 studied data on light hydrocarbon-liquid systems containing methane and ethane at high temperature and pressure and have presented a method for determining liquid densities, assuming additive volumes for all components less volatile than ethane and using apparent densities for methane and ethane. The compressibility and thermal-expansion curves used by Standing are based on assumptions that compressibility of a hydrocarbon liquid at temperatures below 300°F is a function of the liquid density at 60°F and that thermal expansion of the liquid is affected little by pressure. The information required to use this technique with an example problem is furnished by Standing.' Hanson eports an average error of - 0.5 per cent using the method of apparent densities in calculating liquid densities of several volatile hydrocarbon mixtures. However, as implied, the apparent density method is not applicable for liquid density calculations when the composition of the liquid is unknown. Watson- as presented a method

By Benny J. Nelson

AS a part of the fundamental research program of Aluminum Research Laboratories, some data were obtained on the ternary system Mg-Al-Mn. As very little information on the magnesium corner of this diagram has heretofore been published, it seems desirable to make available the values found for the liquidus and solidus surfaces of this system. Procedure The settling procedure was used for the determination of the liquidus compositions. Metallo-graphic examination of quenched samples, and stress-rupture upon incipient melting, were used for the solidus determinations. The settling procedure has been described in a previous paper.' Briefly, this method involved saturating the alloy with manganese at a temperature substantially above that at which the sohbility was to be determined, then cooling the melt to the latter temperature, and holding it at that temperature for a substantial period of time. Samples for analysis .were carefully ladled from the upper portion of the melt at hourly intervals during the holding period. After the ladling of each sample, the melt was stirred to redistribute some of the manganese that had already settled, because it appeared that when the latter particles of manganese again settled, they aided in carrying down more of the manganese and thus hastened the attainment of equilibrium. The melts were prepared and held in a No. 8 Tercod crucible holding approximately 4 lb of metal. The manganese was added either in the form of a prealloyed ingot (Dow M) containing about 1.5 pct Mn or by the use of a flux (Dow 250) containing manganese chloride. In calculating the flux additions, it was assumed that the manganese introduced would be equal to 22 pct of the total weight of the flux. Temperatures were measured with an iron-constantan thermocouple enclosed in a seamless steel tube, the lower end of which was welded shut. This protection tube also served as a stirring rod. The samples ladled from the upper portions of the melts at the various intervals were analyzed for aluminum, manganese, and iron. When making the alloys which were to be used for the determination of the solidus, 2½ in. diam tilt mold ingots were cast, scalped to 2.0 in. in diam, and extruded into ? in. diam wire. The principal impurities in the melts for this investigation were iron and silicon; their total not exceeding 0.03 pct. Portions of the wire, approximately 2 in. in length, were enclosed in stainless steel capsules for protection from the atmosphere. Bundles of these capsules, with a dummy capsule containing an iron-constantan thermocouple, were heated inside a large steel block (acting as a heat reservoir) in a closed circulating-air type electric furnace. At ap- propriate times, the capsules were removed and quenched in water. The wires were examined metallographically to determine the temperature of initial melting. Short times at temperature were used at the beginning for wire specimens of all alloys to obtain quickly the approximate temperatures at which melting could be first observed. When approximate solidus temperatures had thus been determined, equilibrium heating was attempted. This equilibrium heating consisted of an 8 or 16 hr period at a temperature, about 50 °F below the lowest temperature at which melting occurred when short heating cycles were used, followed by further heating for 1 hr periods at consecutive 10" higher temperatures. The theory for the method of stress-rupture at incipient melting has been well covereda and its limitations are recognized. Thus, if the interfacial tensions are such that the first minute quantity of liquid is "bunched up" at the grain boundary junctions instead of spreading out along the grain boundaries,³ temperatures higher than the solidus are required before melting will be manifested by rupture of the specimen. This point will be elaborated later. Specimens of the wires with a reduced section (approximately 1/16 in. diam) were suspended vertically in a tubular furnace. The setup used is shown in Fig. 1. The clamp holding the specimen was made from alumel thermocouple wire and the thermocouple was thus completed across the specimen by attaching a chrome1 wire to its lower end. Temperatures were read from a Speedomax recorder used in conjunction with a calibrated thermocouple. The small weight attached to the specimen and a vibrator attached to the furnace tube, to aid in distributing the molten constituent along the grain boundaries, were used to bring about rupture at a temperature closely approximating the solidus. The specimens were heated at a rate of about 5°C per min. The rupture of the specimens was indicated both by sound and by the action of the recorder. An argon atmosphere containing a small amount of SO² was used for protection of the specimen. The assembly was taken out of the furnace immediately following rupture and the specimen removed. Some of the broken specimens were examined metallographically and will be referred to later. Results and Discussion Fig. 2 shows a set of typical time-composition curves for liquid samples of the Mg-Al-Mn alloys used for the settling tests. The data as presented

Jan 1, 1952