Search Documents

By R. J. Quigg, G. S. Doble

Commercial stress -relieved TD Nickel bar was shown to retain room- and elevated-temperature tensile strength after exposure up to 2501°F. Cold swaging increased both room -temperature and 2000°F tensile strength. After annealing at 2500°F the strengthening due to swaging was retained at 2000°F hilt eliminated at room temperature. Annealing produced changes in hardness and X-ray half peak width indicating the presence of recovery processes as 1071° as 1000°F but no recrystallization of swaged material was noted at any temperature. In contrast to swaging, rolling induced a recrystal-lized structure after annealing. The tensile strength of this recrystallized structure was comparable to the cold-worked condition. High-temperature tensile properties of as -received bar were highly anisotropic with the transverse tensile strength being one fifth the longitudinal value. The aniso-/ropy is affected by working direction and may he partially reversed by changing the direction of metal flow. The divergence in tensile strength, beginning above 550°F or- approximate one third the absolute melting point, is strain-rate dependent. T D Nickel is a commercial dispersion-hardened alloy containing 2 vol pct thoria. The dispersion, consisting of spherical particles 0.030 to 0.050 in diameter with an interparticle spacing of less than 1 is reported to maintain stable properties up to 2400°F.1 This stability of second phase results in maintenance of elevated-temperature strength at higher temperatures and longer times than normal nickel-base superalloys.2 The purpose of this paper is to describe the effect of various mechanical working operations on the strength and microstructural stability of TD Nickel bar. MATERIAL AND PROCEDURES All material used in this study was commercial TD Nickel bar. This material is produced by a chemical process which results in a nickel powder containing a dispersion of thoria particles. The powder is then pressed, sintered, extruded, and subsequently worked to bar stock. Three starting materials from three separate lots were used: as-extruded bar. 1-in.-diam stress-relieved bar, and 1/2-in.-diam stress-relieved bar. Since TD Nickel bar stock is cold-worked without a recrystalliza-tion anneal, the accumulated deformation or degree of cold work in these materials increases as the bar diameter decreases. Some of the 1/2-in.-diam bar was swaged to 1/4 in. diameter at room temperature in order to produce an as-worked condition for comparison with the stress-relieved stock. Tensile testing was performed on an Instron Tensile Tester at a constant crosshead speed of 0.020 in. per min. The 0.2 pct offset yield strength was measured from the load-crosshead movement plot. Specimen gage dimensions were 0.080 in. in diameter by 0.40 in. in length, producing a strain rate of approximately 0.050 min-1. Specimens were tested in air and heated within a resistance-wound furnace controlled to ±5°F. A 15-min soak at temperature was employed before testing. Samples were heat-treated in air and specimens machined after exposure with sufficient material removed to eliminate any surface contamination. X-ray line breadth was determined from a diffractometer scan of a transverse face of a bar using copper K, radiation. Metallographic preparation utilized standard mechanical polishing with Carapella's etch. Specimens for electron microscopy were electropolished in a 1:7 sulfuric/methaol solution and chromium-shadowed collodion replicas prepared. RESULTS AND DISCUSSION I) Effect of Elevated-Temperature Exposure on the properties of TD Nickel. The effect of various elevated-temperature exposures on the room-temperature tensile strength of TD Nickel is shown in Table I. In the unexposed condition the tensile strength, reduction in area, and hardness all increase with increasing accumulated deformation while the elongation decreases. After exposure at 2500°F the strength of all three materials decreases to about 65,000 psi and the elongations increase slightly. The apparent increase in strength of the 1-in. bar after a 2000°F treatment is probably experimental scatter. These results indicate that the room-temperature strengthening due to additional deformation is annealed out upon elevated-temperature exposure. In contrast to the room-temperature data, the 2000°F tensile strengths increase in order of increasing deformation even after exposure. Although some loss of strength occurs after exposure, much of the effect of working is still maintained at 2000°F. The room-temperature hardness after various

Jan 1, 1965

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By B. E. Morgan, C. K. Dumbauld

The need for a low-strength cementing composition for use in well cementing is reviewed and results are presented of laboratory and experimental field tests of a modified cement having a controlled ultimate tensile strength of approximately 200 psi. The modified cementing composition may he prepared from either high early strength or normal portland cements by the addition of bentonite clay and a suitable agent for dispersing and controlling the set of the slurry. Substitution of the modified cement for conventional slow-set cements may give better completion results in many wells because the modified cementing composition has lower set strength, lower slurry density, and greater slurry stability than conventional cement slurrieh. The lower ultimate strength allows greater penetration with less shattering of the set cement when perforating casing and cement. The lower elurry density allows the placement of longer columns of cement slurry, and the greater slurry stability reduces the possibility of having an uncemented section caused by the settling of cement particles before the cement set.. INTRODUCTION High strength lias always been one of the accepted criteria of a good cement. During the early use of portland cement in well cementing. emphasis was placed upon securing cements with higher strengths. In 1931, Barkis' reported that, "Normal oil well cements have been improved to develop greater strengths and uniformity of product, which has aided in producing successful jobs in cementing the deeper strings." As long as most wells were completed by the open-hole method. the use of cements having high strengths seemed desirable, and there was no objection raised against high-strength cementing compositions. For a number of years. how-ever, the industry has been completing a large numher of wells by setting and cementing casing through productive horizons and then obtaining production by gun-perforating the section of casing opposite the desired interval. Although this method has been generally successful, difficulties have been experienced in some cases in completing or recompleting wells because of apparent lack of adequate penetration by the bullets through the casing and surrounding sheath of cement and into producing formation. In addition to the penetration trouble: there have been indications that fracturing and shattering of the set cement by perforating might he a contributing factor in causing the failure of some jobs to exclude water or gas from oil producing zones. The possibility that cements having high set strengths were contributing to til difficully ill obtaining satihfartory perforating results has re. ceived attention during recent years. Gun perforating tests conducted in 1944 showed that the depth of bullet penetration into set cement varied with the hardness of the cement, the greater the strength of the cement the less being the penetration. In 1946, Farris2 pointed out that high strength cements were not needed in well cementing, and in 1947, data published by Oliphant and Farris3 showed that set cement was perforated without shattering at approximately 150 psi tensile strength. whereas at approximately 300 psi tensile strength severe cracking and shattering occurred. Oliphant and Farris suggested that wells be perforated at the proper time interval after placement of the cement so that the set cement would have the desired strength. Several difficulties may he encountered in trying to perforate a cement job at the correct time to catch the tensile strength near 150 psi. The rate of strength development of different cements varies considerably. This fact is illustrated by results of tensile strength measurements presented in Fig. 1. These data show that at 175°F the tensile strengths of three conventional slow-set cements varied from 75 to 235 psi at the end of 12 hours. After 24 hours, the tensile strengths varied from 200 to 455 psi. The rate of strength development is affected. also. by the temperature of the forniation, and this adds to the uncertainty of perforating at the rorrect time, since accurate well cementing temperatures may not he known in many cases. Furthermore, in the recomple-tion of wells it is sometimes necessary to perforate cement which has set for a long period and has developed maximum or final strength. In view of the apparent need for a cementing composition having a controlled ultimate strength, an investigation was

Jan 1, 1951

By C. K. Dumbauld, B. E. Morgan

The need for a low-strength cementing composition for use in well cementing is reviewed and results are presented of laboratory and experimental field tests of a modified cement having a controlled ultimate tensile strength of approximately 200 psi. The modified cementing composition may he prepared from either high early strength or normal portland cements by the addition of bentonite clay and a suitable agent for dispersing and controlling the set of the slurry. Substitution of the modified cement for conventional slow-set cements may give better completion results in many wells because the modified cementing composition has lower set strength, lower slurry density, and greater slurry stability than conventional cement slurrieh. The lower ultimate strength allows greater penetration with less shattering of the set cement when perforating casing and cement. The lower elurry density allows the placement of longer columns of cement slurry, and the greater slurry stability reduces the possibility of having an uncemented section caused by the settling of cement particles before the cement set.. INTRODUCTION High strength lias always been one of the accepted criteria of a good cement. During the early use of portland cement in well cementing. emphasis was placed upon securing cements with higher strengths. In 1931, Barkis' reported that, "Normal oil well cements have been improved to develop greater strengths and uniformity of product, which has aided in producing successful jobs in cementing the deeper strings." As long as most wells were completed by the open-hole method. the use of cements having high strengths seemed desirable, and there was no objection raised against high-strength cementing compositions. For a number of years. how-ever, the industry has been completing a large numher of wells by setting and cementing casing through productive horizons and then obtaining production by gun-perforating the section of casing opposite the desired interval. Although this method has been generally successful, difficulties have been experienced in some cases in completing or recompleting wells because of apparent lack of adequate penetration by the bullets through the casing and surrounding sheath of cement and into producing formation. In addition to the penetration trouble: there have been indications that fracturing and shattering of the set cement by perforating might he a contributing factor in causing the failure of some jobs to exclude water or gas from oil producing zones. The possibility that cements having high set strengths were contributing to til difficully ill obtaining satihfartory perforating results has re. ceived attention during recent years. Gun perforating tests conducted in 1944 showed that the depth of bullet penetration into set cement varied with the hardness of the cement, the greater the strength of the cement the less being the penetration. In 1946, Farris2 pointed out that high strength cements were not needed in well cementing, and in 1947, data published by Oliphant and Farris3 showed that set cement was perforated without shattering at approximately 150 psi tensile strength. whereas at approximately 300 psi tensile strength severe cracking and shattering occurred. Oliphant and Farris suggested that wells be perforated at the proper time interval after placement of the cement so that the set cement would have the desired strength. Several difficulties may he encountered in trying to perforate a cement job at the correct time to catch the tensile strength near 150 psi. The rate of strength development of different cements varies considerably. This fact is illustrated by results of tensile strength measurements presented in Fig. 1. These data show that at 175°F the tensile strengths of three conventional slow-set cements varied from 75 to 235 psi at the end of 12 hours. After 24 hours, the tensile strengths varied from 200 to 455 psi. The rate of strength development is affected. also. by the temperature of the forniation, and this adds to the uncertainty of perforating at the rorrect time, since accurate well cementing temperatures may not he known in many cases. Furthermore, in the recomple-tion of wells it is sometimes necessary to perforate cement which has set for a long period and has developed maximum or final strength. In view of the apparent need for a cementing composition having a controlled ultimate strength, an investigation was

Jan 1, 1951

Jan 1, 1942

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a'. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

ATHOUGH the open-hearth charge contributes CO, CO2, and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion, the latter being regarded simply as the source of any extra heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were obtained by blowing in air or oxygen, as is the case in the Bessemer converter, then the net heat absorption would be negative, that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with Bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000°F. (1600 to 1650°C.) so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTTNG In the previous chapter it was pointed out that in a typical heat, the fuel furnishes about four million B.t.u. per ton of steel produced. The heat required for the metallurgical processes is not easily defined in useful manner (as is shown later), but it ranges downward from about one million B.t.u., depending not only on the charge but on the manner of calculation. In any event this requirement appears quite small in comparison with the heat furnished by the fuel and invites

Jan 1, 1944

THERE is probably no phase of basic open-hearth steelmaking that is more of an art and less of a science than mold and pouring practice. It varies widely from plant to plant; consequently it is obviously impossible to set down in detail in this chapter the many ramifications of practice that are now used. The discussion that follows therefore attempts only to give an outline of the more common methods, with examples sufficient to indicate some of the variations in procedure, and to emphasize a few of the many underlying problems that face the open-hearth operator at the pouring platform. MOLD DESIGN Ingot molds are hollow castings of considerable wall thickness. Despite this, non-uniformity in wall thickness should be strictly avoided to prevent the setting up of unnecessary stresses. Molds are cast in various forms, sizes, and shapes depending on the type of steel, and on whether the ingot is to be withdrawn from the mold or the mold from the ingot. The selection of ingot-mold material, which is usually cupola or blast-furnace iron containing approximately 3.5 per cent carbon, 1 per cent silicon, 0.9 per cent manganese, 0.2 per cent phosphorus, and 0.07 per cent sulphur, is governed by numerous considerations that affect mold life. (1) Factors in addition to wall thickness that should be given primary consideration at the foundry are casting skin, shrinkage stresses, and casting temperature. Factors in Mold Design. In use, mold thickness is of greatest importance, for it must be heavy enough to freeze the molten metal rising in the mold and to reduce the temperature of the steel below that of the melting point of cast iron to prevent the inner surface of the mold from melting, which would result in the welding of the ingot to the mold. The skin of an ingot, which solidities immediately upon contact with the relatively cold walls of the mold, must soon become thick enough to contract on the fluid mass and pull away slightly from the sides of the mold. The separation of the ingot from the mold depends entirely on the heat taken up by the mold from the steel.

Jan 1, 1944

By John C. Gifford, Charles L. Thomas

A unique and reproducible method is presented for the determination of water vapor in tough pitch wire bar copper. The procedure involves reduction of the water vapor with molten aluminum to form hydrogen, which is subsequently measured by mass spectroscopy. Average water vapor pressures within the porosities of the wire bar samples are calculated. Correlation is to exist between the specific gravities of the samples and their measured water vapor contents. The method should find application as a very sensitive means of detecting hydrogen embrittlement in copper. The nature and quantity of gases evolved and retained during the horizontal casting of tough pitch wire bar copper have long been of interest to the metallurgist. Considerable work has been done at this laboratory on the determination of these gases. The work has involved not only qualitative but also quantitative analysis, so as to provide a basis for a total accounting of the porosity which is associated with the cast product. From a knowledge of the gas-forming elements within the copper, and the practice of melting and protecting it with a reducing flame followed by contact with a charcoal cover in the casting ladle, the gases which one might expect to find in the pores of the cast product are sulfur dioxide, carbon monoxide, carbon dioxide, hydrogen, and water vapor. Hydrogen sulfide, nitrogen, and hydrocarbons would be other possibilities; however vacuum fusion-mass spectroscopy techniques employed at this laboratory have shown that no hydrogen sulfide and only traces of nitrogen and methane are present. It is highly improbable according to phillipsl that any sulfur dioxide could be evolved in wire bar copper with 10 ppm or less sulfur under normal freezing conditions. Mackay and smith2 have noted that porosity due to sulfur dioxide only becomes noticeable at concentrations above 20 ppm S. Investigation of carbon monoxide and carbon dioxide by a variation in the method of Bever and Floe showed that these two gases could only account, at 760 mm and 1064°C (Cu-Cua eutectic temperature), for a maximum of about 25 pct of the total porosity in a wire bar having a specific gravity of 8.40 g per cu cm. phillips' has noted that no normal furnace atmosphere is ever sufficiently rich in hydrogen to cause porosity in copper from hydrogen alone. In addition, using a hot vacuum extraction technique for hydrogen,4 values have never been observed in excess of 10 ppb in tough pitch wire bar. On the basis of the preceding considerations of gases in tough pitch wire bar, only water vapor is left to account for the major portion of the porosity. Direct determinations of water vapor are virtually impossible at low concentrations by any presently known technique, due to adsorption and desorption within the walls of the apparatus used.5 The present investigation deals with a method for the determination of water vapor by an indirect procedure, using molten aluminum as a reducing agent to form hydrogen according to the reaction: 2A1 + 3H2O — A12O3 + 3H2 The evolved hydrogen can then be measured quantitatively by mass spectroscopy. EXPERIMENTAL A 10-g piece of 99.9+ pct A1 was charged into a porous alumina crucible (Laboratory Equipment Co., No. 528-30). Fig. 1 shows the crucible in place at the bottom of an 8-in.-long quartz thimble. A funnel tube with two l1/8-in.-OD sidearms extending at a 90-deg angle from each other was attached to the top of the thimble. One of the sidearms was joined to the inlet system of the mass spectrometer (Consolidated Electrodynamics Corp. Model 21-620A) via a mercury diffusion pump situated between two dry-ice traps. The copper samples were placed in the other sidearm, followed by a glass-enclosed magnetic stirring bar for pushing the samples into the crucible. All ground joints were sealed with vacuum-grade wax. The entire system was evacuated and the aluminum was heated with a T-2.5 Lepel High Frequency Induction Furnace for 21/2 hr at a temperature visually estimated to be 900°C. The temperature was then lowered and the hydrogen was monitored on the mass spectrometer until it was given off at a constant rate of about 4 to 5 1 per hr. This rate corresponded to a slope of 2 to 3 divisions per min on the X3 attenuation of a 10-mv recorder at a hydrogen sensitivity of approximately 100 divisions per 1. A micromanometer (Consolidated Electrodynamics Corp. Model 23-105)

Jan 1, 1969

By Walter Crafts, W. D. Forging, John J. Egan

Although many elements reduce the tendency to porosity in steel castings, manganese, silicon, aluminum, calcium, titanium and zirconium appear to be most generally suitable for the purpose. The manganese and silicon contents are usually maintained in a fairly constant range. Silicon-killed castings often are made to be sound with little or no addition of the stronger degasifiers. In many cases, however, it is more practical to utilize the stronger degasifying elements, aluminum, calcium, titanium and zirconium. Since they greatly modify the composition, shape, and distribution of the nonmetallic inclusions, and thereby the ductility, the strong deoxidizers must be used in such a way as to form the least harmful types of inclusions. As the reasons for failure always to obtain good results have not been obvious, an effort has been made to determine the mechanism of solidification of steels deoxidized to produce certain types of inclusions. Diagrams representsing the mechanism of their formation have been constructed from the appearance of the nonmetallic constituents and have not only illustrated the limiting features of specific deoxidizing treatments with respect to inclusion formation and ductility, but have also indicated a relation between inclusions and resistance to hot tearing. Three different types of deoxidation treatment have been used for obtaining sound castings with relatively high ductility. The first method is to make and cast the steel under such conditions that deoxidation with silicon and a small addition of a strong deoxidizer assures soundness. The effective addition that will promote soundness without causing the formation of intergranular inclusions varies with the furnace practice and composition, but may be limitled to about 0.025 per cent Al, Zr or Ti. Up to 8.10 per cent Ca and 0.15 per cent V are also used for this purpose. The inclusions in these steels are characteristically glassy silicates and round or irregular sulphides. As pointed out by Sims and Lillieqvist,1 the formation of fine intergranular inclusions, which are detrimental to ductility, limits the amount of strong deoxidizers that may be added.

Jan 1, 1940

By John J. Egan, W. D. Forging, Walter Crafts

Although many elements reduce the tendency to porosity in steel castings, manganese, silicon, aluminum, calcium, titanium and zirconium appear to be most generally suitable for the purpose. The manganese and silicon contents are usually maintained in a fairly constant range. Silicon-killed castings often are made to be sound with little or no addition of the stronger degasifiers. In many cases, however, it is more practical to utilize the stronger degasifying elements, aluminum, calcium, titanium and zirconium. Since they greatly modify the composition, shape, and distribution of the nonmetallic inclusions, and thereby the ductility, the strong deoxidizers must be used in such a way as to form the least harmful types of inclusions. As the reasons for failure always to obtain good results have not been obvious, an effort has been made to determine the mechanism of solidification of steels deoxidized to produce certain types of inclusions. Diagrams representsing the mechanism of their formation have been constructed from the appearance of the nonmetallic constituents and have not only illustrated the limiting features of specific deoxidizing treatments with respect to inclusion formation and ductility, but have also indicated a relation between inclusions and resistance to hot tearing. Three different types of deoxidation treatment have been used for obtaining sound castings with relatively high ductility. The first method is to make and cast the steel under such conditions that deoxidation with silicon and a small addition of a strong deoxidizer assures soundness. The effective addition that will promote soundness without causing the formation of intergranular inclusions varies with the furnace practice and composition, but may be limitled to about 0.025 per cent Al, Zr or Ti. Up to 8.10 per cent Ca and 0.15 per cent V are also used for this purpose. The inclusions in these steels are characteristically glassy silicates and round or irregular sulphides. As pointed out by Sims and Lillieqvist,1 the formation of fine intergranular inclusions, which are detrimental to ductility, limits the amount of strong deoxidizers that may be added.

Jan 1, 1940

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By J. H. Carpenter

LMENITE, rutile, zircon, and other heavy minerals are found in small amounts in the sand that covers most of Florida. Small enriched deposits occur on the beaches and coastal dunes. One beach deposit east of Jacksonville was worked during World War I and another near Vero Beach during World War 11. Both ceased operation when the resumption of imports reduced prices. Early in World War II reduction of rutile imports made a domestic source of the mineral necessary to maintain the expansion of armaments. Explorations made near Jacksonville discovered a relatively large body of low-grade ore about 10 miles inland from the beaches. A plant installed by Rutile Mining Co. of Florida using both flotation and tables encountered difficulties because of low plant capacity and organic slimes in the ore. In 1944 Humphreys Gold Corp. solved the problem of concentrating the low-grade ore by using the newly developed Humphreys spiral concentrator and by mining with a hydraulic dredge. This combination of low cost mining and concentration permitted the plant to continue operation in competition with foreign ores when imports were resumed following the war. The success of the Jacksonville operation renewed interest in Florida as a source of titanium. An extensive survey of the state was made by E. I. du Pont de Nemours and Co., Inc., under the direction of J. L. Gillson in 1945 to 1946. Sampling was carried on by drive pipe drilling to depths of 20 to 25 ft. Encouraging values were discovered near the location of the present Trail Ridge mine, 50 miles southwest of Jacksonville, near the town of Starke. The United States Bureau of Mines was interested in exploring for heavy minerals in Florida, and on the recommendation of both the state geologist of Florida and of Du Pont geologists, drilled deeper where marginal indications were found on Trail Ridge. In 1947 it was discovered that sufficiently higher values occurred at depth to make the deposit commercial. The orebody at Trail Ridge is a long sand deposit averaging about 1 mile in width and 35 ft in depth. It is approximately 1 1/2 miles wide at the north end of the portion now being worked, tapering to a blunt point 3 miles to the south. The ore reaches a maximum depth of 65 ft near the center and feathers out into barren sand at the edges. The ground surface is relatively flat and is covered with vegetation including pine, scrub oak, palmetto, and occasionally in swampy areas, cypress. The remain of a dense woody growth underlies and marks the bottom of the Ore 'One. It is difficult to drill through this layer, but in some cases where it is less than 5 ft thick it has been possible to drive through the wood. Sand lying below is coarser than that in the ore zone and contains no values. The wood layer consists of unconsolidated carbonized fragments of branches and other forest trash associated with a considerable amount of ar-

Jan 1, 1954

By R. J. Wysor

CHARLES H. RICH, Conshohocken, Pa. (communication to the Secretary*).-Mr. Wysor has certainly covered his subject in the most thorough and able manner and his paper will no doubt result in enlarged effort toward the conservation of this important byproduct. Not all furnace burdens are as rich in alkalies as those noted by Mr. Wysor. In our own experience we have never gone into any extended examination of the materials entering the furnace burdens, but have made a number of determinations of the water-soluble alkalies of our flue and boiler dust and found maximum of about 4 1/2 per cent. K20-too small for profitable reclamation. We have, however, frequently encountered the smoky gas described by Mr. Wysor. Such gas carries heavy fume, and buds with a fitful flame difficult to maintain. So pronounced was the inhibitory effect of the fume that, in extreme cases, the flame of a lighted match was extinguished by the current of gas and it was found impossible to conduct calorimeter tests without preliminary washing of the gas. When the gas was led through a washer filled with distilled water and pieces of coke, the fume was absorbed and the gas burned without difficulty. Careful analyses conducted on the water solution from the washer showed cyanides in increasing amounts in proportion to the difficulty experienced in burning the gas. We, note Mr. Wysor's statement that he has never found evidence of cyanides in their gas, ascribing the difficulty of burning such gas to the presence of chlorides. Our determinations were conducted in such manner as to preclude possibility of interference by chlorine.

Jan 3, 1917

By C. H. Mathewson, A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By W. P. Dyrenforth, W. E. Horst

Although, separating or concentrating minerals, based on differences in. their magnetic properties has been practiced for years1 the early industrial applications of magnetic separators were involved with the most highly magnetic materials. These early separators were used to concentrate magnetite, separate metallic iron from furnace products, and separate iron and brass turnings. Next, the addition of a pretreatment operation, such as roasting or calcining, to transform certain iron-bearing minerals into a highly magnetic compound that could readily be separated from the altered mineral mixture using existing magnetic separation machines was added to the flowscheme. As the number of magnetic-separator installations grew, steady development of better equipment evolved including the design and implementation of induced magnets having high-intensity fields, These developments of course greatly expanded the field of magnetic separation and made it possible to commercially separate or concentrate very weakly magnetic minerals which previously had been considered as nonmagnetic minerals. A number of different designs of magnetic separators were well developed and the unit operation of magnetic separation was gaining wide acceptance in mineral processing operations when two events occurred that dampened these developments. First, the Mesabi iron range with its direct-shipping iron ore was discovered and placed into operation. This of course significantly reduced the need for magnetic separation to meet the raw material requirements of the iron and steel industry. Second, the advent of selective froth flotation, was so successful in solving many mineral process problems that electrical concentration techniques being developed at that time, including magnetic-separation methods, were either terminated or received low priority ratings. During the past two decades interest has been renewed in the use of electrical concentration methods to solve mineral separation problems. As the direct-shipping iron ore reserves are depleted more emphasis has been placed on magnetic upgrading of lower value iron ore available throughout the world. In addition, magnetic separation techniques have found numerous applications in the non-metallic and industrial minerals industry to supplement froth flotation and thus add to the variety of beneficiation methods available.

Jan 1, 1971

By Colin C. Rae

The absence of paraffin and other oil hydrocarbons in the soil although they are concentrated in extensive deposits in some localities, the common distribution of plant remains through many formations that are not productive for oil, and many other factors, seem to indicate the existence of an intermediate organic compound between the complex plant compounds and the petroleum hydrocarbons; and much evidence points to the humus acids or associated organic compounds, which are probably collected by surface waters and concentrated in certain areas by means of precipitation by electrolytes, which would be contained in sea water or possibly in various inland seas or lakes. Present-day Evidence There are many present-day evidences of the association of petroleum with humus acids. Binney, in 1912, made observations without explanations on the peat mosses of Down Holland, England, where he found petroleum being formed by decomposition in the presence of an infiltration of sea water. The analysis of a typical peat will show its relationship to the humus acids under consideration. Sample No. 1, SamplE No. 2. PXr Cent. PER CENt. Water......................... 20.0 29.6 Ash.......................... 3.0 3.05 Fiber.......................... 47.0 54.95 Humus acids................ 30.0 12.50 J. D. Haseman and others have noted the association of asphalt and hydrocarbons with the swampy, boggy areas, particularly adjacent to the sea. Many of the rivers carry much humus acid in solution, and some tropical rivers carry in the aggregate millions of tons of humus each year. The amount of humus is a variable factor, depending on climatic conditions, and on the salts and alkalies present in the water, also on the density and temperature.

Jan 1, 1923