Search Documents

By Bernard York, John J. Reed

W. 0. Philbrook (Carnegie Institute of Technology, Phila.)—Mr. DeVaney's paper is a valuable addition to the growing technology of the magnetic roasting of lean iron ores. His furnace is ingeniously designed to permit close control of the process and to achieve high thermal efficiency by counter-current heat exchange and the withdrawal of both solid and gaseous products at relatively low temperatures. The principle of using a lean reducing gas to avoid over-reduction of the ore even at high operating temperatures (for rapid reaction rate) is thoroughly sound. The gas analyses and flow rates reported, however, are internally incon- sistent and render suspect any details of a heat balance based upon them. While it is entirely proper to consider the entrant gas as a reagent and to account only for the heat evolved by consuming a portion of the gas, many operators are accustomed to a heat balance using the total calorific value of the reagent supplied; and comparison of heat balances made with different bases of calculation can be quite misleading. Since Mr. DeVaney's paper is likely to be cited frequently in future discussions of magnetic roasting processes, it seems worth while to point out the internal discrepancies and to give alternate values of heat requirements for different bases of calculation.

Jan 1, 1954

By W. E. C. Eustis

1st. THE fine iron ore is mixed with a sufficient proportion of fine coking coal, and is coked in any of the ordinary methods for making coke. The effect of this is to convert the iron oxide into sponge in such a shape that the usual trouble of oxidation is avoided. 2d. The resulting mixture of coke and sponge is melted down in an ordinary cupola, the coke furnishing more than sufficient fuel for that purpose. I may briefly point out here that in the first place the iron is sponged, and this sponge, as is well known, contain-, no phosphorus or silicon when the reduction takes place at a low temperature; and in the second place this sponge is melted down in a cupola in which there is no zone of reduction for phosphorus or silicon, and that con¬sequently the resulting iron should be free from both of these impu¬rities. 3d. The liquid sponge, now carburized, is run into an open-hearth furnace, where the requisite degree of hardness or softness is obtained by adding some of the fine ore, and the usual dose of ferronmanganose. I have merely given above the rough outlines of the process, but it is my intention, as early as possible, to bring the process more fully before the Institute.

Jan 1, 1881

By W. E. C. Eustis

1st. The fine iron ore is mixed with a sufficient proportion of fine coking coal, and is coked in any of the ordinary methods for making coke. The effect of this is to convert the iron oxide into sponge in such a shape that the usual trouble of oxidation is avoided. 2d. The resulting mixture of coke and sponge is melted down ill an ordinary cupola, the coke furnishing more than sufficient fuel for that purpose. I may briefly point out here that in the first place the iron is sponged, and this sponge, as is well known, contains no phosphoras or silicon when the reduction takes place at a low temperature; and in the second place this sponge is melted down in a cupola in which there is no zone of reduction for phosphorus or silicon, and that con . sequently the resulting iron should be free from both of these impurities. 3d. The liquid sponge, now carburized, is run into an open-hearth furnace, where the requisite degree of hardness or softness is obtained by adding some of the fine ore, and the usual dose of ferromanganese, I have merely given above the rough outlines of the prows, bat it is my intention, as early as possible, to bring the process more fully before the Institute.

Jan 1, 1881

By Harvey N. Davis

MUCH has been written and said during the last twenty years about the place of the engineer in modern life, about the fundamental role that he plays both in developing and in maintaining the material foundations of modern civilization, about the advantages, and also the dangers, of the machine age that he has inaugurated, about the Frankenstein problems that he has unconcernedly foisted upon a generation utterly unable to cope with them, and about the obligation that rests upon him to stop inventing machines and turn his almost legendary energy and skill to inventing institutions that will constitute a solution of the problems he has raised, and contrariwise about his utter inability to offer wise or useful counsel in fields outside the narrow boundaries of his technical training.

Jan 1, 1938

By W. N. Best

Crude oil attracted attention because of its excellence as a fuel for openhearth furnaoes; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hotair furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This mcans a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity BaumB. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230". F., Mexican crude oil at from 175" to 210" F., and Beaumont, Texas, oil at 142" F. Fuel oil vaporizes at 130" F. Scientific Installation Essential The burning of oil is an art based on science, and the "rule of thumb" should never be employed, especially in heating heavy crude oil. Thermometers should be used on both suction and supply pipes so that the fireman or smith will at all times know the temperature of the fuel. The indicators on such thermometers should be large enough to be readily seen by the operator, night or day. It is necessary to have an unvarying pressure of steam or air through the burner, to atomize the fuel. Also, the air used to support combustion should be delivered through a nozzle under the burner at a constant pressure. The oil pressure must not fluctuate; under no eircumstances should it vary more than 1 1b. The oil pump, which should be brass-lined, with the aid of the pulsometer and superheater, will insure a constant

Jan 1, 1916

By Harry A. Lipsitt, Attwell M. Adair

A number of papers have appeared in the past several years concerning the nature of the fatigue limit. The hypotheses presented in those papers fall into three groups. Some authors attribute the fatigue limit to the distribution of interstitials prior to testing (static group). Others consider the fatigue limit to be due to dislocation-interstitial reactions during testing (dynamic group). Still other propose that the fatigue limit results from a characteristic peculiar to the iron (bee) lattice (inherent group). This communication is an attempt to digest the salient features of each of the hypotheses, discuss them, and present some constructive criticism. It is shown that each of the extant ideas has some merit, and that each of the mechanisms thus far proposed is necessary, but individually insufficient, to provide the desired level of understanding of the fatigue-limit behavior of metals. Static Group. The data of Oates and wilson1 on finegrained (=0.022 mm diam) low-carbon steel indicate that the fatigue limit exists in the absence of sufficient plastic deformation for any dynamic strain-aging mechanism to be operative. Specimens tested just below the fatigue limit showed yield-point behavior typical for unstrained material when removed from the fatigue machine and tested in tension. These results led them to the conclusion that initial dislocation locking controls the fatigue limit in this material, which has a yield stress higher than the fatigue-limit stress. Prestraining this material just prior to fatigue testing would be expected to lower the fatigue-limit stress; this they observed experimentally. Yoshikawa and sugeno2 are of the opinion that the sharp fatigue limit in fine-grained iron is caused by

Jan 1, 1967

By Oswald J. Heinrich

The deposit of rock salt along the shores of Lake Huron, in Canada, has been brought before the public during the last six months, in consequence of the developments made by the diamond drill at Goderich. It is likely to be of more than common interest in the future, since now actual operations have been commenced to exploit the deposit and work it by regular mining. The methods of mining rock salt being but little known in this country, it may be of interest to make a few general remarks in regard to them before entering, upon the description of this new mining enterprise. According to the conditions under which salt is .found in nature, various methods have been resorted to, in course of time, to make it available for the human race. They consist in: A. Natural or solar evaporation. B. Artificial evaporation, either exclusively or in connection with the former. C. Mining the rock salt in its natural state, and converting it to a marketable product, if need be, by simply pulverizing it. Without going into the details of the various methods of making salt available in an economical point of view, dependent on its degree of pority, or on various local influences, we cannot refrain from alluding to the general principles which influence the mining and manufacturing of salt in countries where they have been carried on for hundreds of years. ECONOMICAL CONDITIONS FOR SUCCESS. Salt being one of the articles of prime necessity, and one universally distributed throughout nature, it must always be sold at a comparatively low price. It would even be quoted in the market at prices far below those now ruling, if it were not for the high duties generally imposed upon it, for purposes of state revenues. But looking closer into the subject, it will be found that this duty is probably one of the least oppressive, although in some countries it exceeds sixfold the cost of profitable production. To produce the article at the lowest possible cost requires, therefore, a

Jan 1, 1879

By T. M. Chance

The first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. The Original Mt. Union Tipple The plant was installed to transfer coal.from steel narrow-gage cars of 60,000 and 70,000 lb. capacity to standard-gage equipment. The coal was hauled about 30 miles from the East Broad Top field. This coa1, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout the original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and, with the layout as originally installed, either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 1, 1927

By W. B. Gogarty

With the use of polymer solutions in secondary recovery operations, the need has developed to understand the mobility control mechanism. This study investigated mobility control by considering both permeability and rheological effects. Experiments used a high molecular weight, partially hydrolyzed polyacrylamide polymer. Flow studies took place in reservoir and Berea cores having zero oil saturation. Effective size of the polymer flow unit was inferred from Nuclepore filter tests. Clay studies indicated the particle size capable of decreasing the core permeability. Flushed permeabilities measured the approximate core permeabilities with flowing polymer solutions. These permeabilities were considerably lower than original values. With mobility data and the flushed permeability, maximum effective viscosities were determined for polymer solution flow in a core. Effective viscosities showed that rheological properties play an important part in mobility control with polymer solutions. The study showed that permeabilities decrease and stabilize with polymer flow. At the lower permeabilities, high shear rates exist in the cores. Because of the pseudoplastic character of the polymer solution, the high shear rates caused low effective viscosities. This condition pointed to the inefficient use of the potentially high viscosity of the polymer solution at low shear rates. INTRODUCTION In the oil industry, a great deal of interest is being shown in the use of polymer solutions for secondary recovery and a number of polymer floods are being performed in the United States.1 Some of these floods have become commercial while others have been reported as failures. A number of floods are still in progress and remain to be evaluated. With the advent of polymer flooding, the need developed to understand the mobility control mechanism in porous media. Rheologically, the polymer solutions behave as pseudoplastic fluids. Investigators have studied the rheology for this type of non-Newtonian fluid in porous media?-6 Results have also been reported on the ability of polymer solutions to decrease mobility.7-10 Some investigators indicated that polymer solutions show a different rheological behavior in cores than on the viscometer.7,8 This study is representative of an initiatory investigation on mobility control with polymer solutions. Some effects are considered on a qualitative basis. Mobility control is considered from the standpoint of both permeability and rheology and, to the extent possible, permeability and rheological effects are considered separately. Results show that mobility control occurs from a reduced permeability caused by polymer retention and an effective viscosity determined by the average shear rate in the core. In this respect, rheological behavior is as important in mobility control as permeability. PROCEDURES A high molecular weight, partially hydrolyzed, polyacrylamide polymer was used in the investigation. Solutions of various concentrations were made with this polymer in different types of water. Some solutions used distilled water and others used tap water. The tap water contained approximately 500 ppm dissolved solids. As used in this paper, concentrations in ppm refer to parts by weight solute to one million parts by weight of solvent. In the tap water, calcium and magnesium accounted for from 60 to 80 ppm of the solids, the remainder being mostly sodium chloride. All solutions contained a bactericide, and anti-oxidants and antiprecipitants were added to the tap water. Capillary and concentric-cylinder* viscometers determined the rheological properties of solutions. The capillary viscometer is described elsewhere.6 Berea and reservoir sandstone were used as core materials for this investigation. Cores were 1 in. in diameter by approximately 2 to 3 in. long. Prior to mounting, the Berea cores were heat-treated for 3 hours at 850F. This treatment decreased the water-sensitivity of the clays in the cores. The reservoir cores were cleaned with solvent and

By C. C. Miller, C. A. Hutchinson, A. B. Dyes

This paper presents a simple and practical method for the estimation of effective permeability and reservoir pressures from the rise in bottom hole pressure when a well is shut in. The equations on which the method is based consider a stabilized well producing from a uniform formation when flow is shut off at the sand face followed by the unsteady state flow of a compressible liquid from regions far from a well to points closer in during the build-up period. An approximation for extending the method for two-phase flow in the reservoir is also presented. In order to compare the effects of extremes in the conditions existing at the external boundary of the reservoir, two general equations defining the build-up characteristics of the reservoir are shown: first, for a reservoir with constant pressure maintained at the radius of drainage, and second, for a reservoir with no influx over the radius of drainage. These equations define the build-up characteristics for the shut-in well as functions of time, the permeability and porosity of the drainage area, the viscosity and compressibility of the fluid flowing, the production rate prior to shut-in, and the radius of drainage of the well. When a well is shut in at the surface, rather than at the sand face, flow will continue into the well bore after shut-in due to the compressibility of the fluids in the bore. The effect upon the build-up characteristics of this flow into the well after shut-in has been studied by means of the electrical analyzer. From the basic relationships and consideration of the limitations due to continued flow after shut-in, methods have been developed for the estimation of the effective permeability of an area from the plot of the build-up characteristics of the well producing that area. Likewise, equations are presented for the estimation of the reservoir pressure from an early portion of the build-up curve. By means of the electrical analyzer, studies have been made concerning the variations in the build-up characteristics resulting from damaged or improved permeability in the immediate vicinity of the well bore. These studies show that the permeability estimated from the build-up curves represents the average effective permeability of the majority of the drainage area and that the permeability in the immediate vicinity of the well does not affect this estimate. Since the major portion of the drawdown is in the immediate vicinity of the well, variations in the permeability of this area greatly affect the productivity of the well as expressed by the productivity index. From pressure build-up and productivity index tests the ratio of the permeability of some arbitrarily specified area immediately surrounding the well and the effective permeability in the majority of the drainage area can be computed. This ratio is a measure of any damage to the well incurred in drilling or reworking and likewise any benefits as a result of remedial measures. In build-up tests and many other tests that are made on a producing well it is at least desirable, if not absolutely necessary, that the well be stabilized prior to testing. A method is presented here for relating the time required to stabilize a well and the reservoir and fluid properties. An equation is also presented for approximation of the length of shut-in time required to obtain sufficient build-up data for the estimation of permeability and reservoir pressure.

Jan 1, 1950

By D. A. Keyes

International Minerals & Chemical Corp. (Canada) Ltd. is presently exploiting by underground mining a potash-rich zone in the middle Devonian Prairie Evaporite formation near Esterhazy, Saskatchewan. Of the three main potash-bearing horizons denoted by Goudie as zones 1, 2 and 3 only the 1ower. two are present at Esterhazy and mining is confined to the lower or zone 1 horizon. The area in which the evaporites were deposited, although flanked on the west by a zone of geosynclinal deposition and tectonic activity, has been subjected to only very gentle epeirogenic activity. The sylvinite ore is coarsely crystalline and occurs in well-defined beds. The halite, sylvite and insoluble content of the ore bears a direct relationship to the lithological units, but the carnallite cuts across the beds. Local concentrations of salt produce blank spots in the ore horizon. Some of these appear to be salt-filled, post-ore channels and cracks while others have been formed by brines emanating upward from below the ore. INTRODUCTION International Minerals & Chemical Corporation (Canada) Ltd. is operating an underground potash mine near the town of Esterhazy in eastern Saskatchewan. The deposit was discovered by IMC in 1955. Subsequent drilling outlined extensive high-grade reserves, and in 1957 shaft sinking and plant construction began. Production from Yarbo No. 1 Shaft commenced in September, 1962 and quickly reached the initial capacity of one million tons of muriate product per year. Production is currently being expanded to 1.6 million tpy. The single mining level is 3140 ft below the surface at No. 1 Shaft. GENERAL GEOLOGY The Esterhazy district lies within the Interior Plains region of Canada and on the northeast rim of the Williston Basin (Fig. 1). Average dip of the rock formations in this area is about 40 ft per mile to the southwest. The potash ore occurs in the Prairie Evaporite formation of the Middle-Devonian Elk Point Group. The Prairie Evaporites are overlain by 3000 ft of Paleozoic shales and limestones and by Jurassic and Cretaceous sandstones and shales (Fig. 2).

Jan 1, 1967

COMMITTEE OF ARRANGEMENTS. General Committee.-J. F. Lewis, Quinnimont, W. Va. Committee of Reception at Staunton.-Major Jed. Hotchkiss, Chairman ; W. A. Burke, M. E. Miller, R. N. Catlett, W. J. Nelson, J. T. Effinger, D. A. Kayser. Local Committee of Arrangements.-G. T. Wickes, Low Moor, Chairman; G. W. Bramwell, Stone Cliff, Secretary; J. E. Johnson, Longdale; H. Firm¬stone, Longdale; S. F. Morris, Quinnimont; O. A. Randall, Ferrol; William N. Page, Ansted; F. Lyman, Low Moor; S. M. Buck, Coalburgh; E. S. Hutchinson, Cannelton ; M. F. Maury, Saltpetre Cave. THE opening session of the Institute was held at Staunton, on Monday evening, May 30th, in the Opera House. Major Jed. Hotchkiss, Chairman of the Committee of Reception, called the meeting to order and introduced Mayor Balthis, who spoke a few words of welcome to the members present, and then introduced the Hon. A. H. H. Stuart. Mr. Stuart in addressing a formal welcome to the Institute to the " little city of the mountains," spoke of the value of the services of the mining engineer in developing the mineral wealth of Virginia and in solving the problems of her geological history. Mr. Metcalf, President of the Institute, replied on behalf of the Institute to the cordial welcome of the mayor and Mr. Stuart, and then read an inaugural address on Force. At the conclusion of the President's address the following papers were read The Electrolytic Determination of Copper and the Formation and Composition of so-called Allotropic Copper, by J. B. Mackintosh, Hoboken, N. J. Read by Professor Egleston. The New Unpublished Map of Chester County, Pa., by Professor Persifor Frazer, Philadelphia. The second session was held at the Opera House on Tuesday morning. The papers read at this session were: Investigations on the Ore Knob Copper Process, by Professor Thomas Egleston, School of Mines, New York city. A Volumetric Estimation of Manganese in Pig Iron and Steel, by F. H. Williams, Vulcan Steel Works, St. Louis, Mo. Read by the Secretary.

Jan 1, 1882

By Kiyoshi Azuma, Hiroshi Kametani

The variation of the dissolution behavior of a ferric oxide with calcining temperature has been investigated. Samples were prepared by thermal decomposition of ferric hydroxide, nitrate, oxalate, and sulfate at low temperature, followed by the calcination in the temperature range between 600" and 1200°C. The samples of eight series and a fine crystalline sample of hematite were dissolved in 1 N hydrochloric acid at 55.2°C and the results are represented on double-log graphs for convenience. It is confirmed that all dissolution courses follouj either the accelerated process or the parabolic process except in the special case of the crystalline hematite which dissolced in accordance with the uniform dissolution of a particle. Examinations of the physical properties of the oxide powders revealed that the surface area measured by the permeability method is strikingly relevant to the dissolution behavior of the oxide. In the previous paper,' detailed data were presented on the effect of the kind of acid, the solution temperature, and the concentration of acid on the dissolution of two ferric oxides. It was also shown that these sam ples dissolved in strikingly different ways. The present investigation was carried out on the dissolution of various calcined samples prepared from various ferri salts by various methods to ascertain the course of dissolution. Pryor and Evans2 pointed out a change of the dissolution rate at around 700°C for a series of calcined ferric oxides prepared from the hydroxide. Several papers374 reported also the dissolution of ferric oxide samples. It seems, however, that a systematic account of the relationship between the dissolution behavior and physical properties of the oxide has not yet been given. This paper presents the variation of the dissolution of the oxide in relation to the calcining temperature and the change of physical properties of the calcines. EXPERIMENTAL Raw materials were prepared by precalcination of ferric hydroxide, thermal decomposition of ferric nitrate, oxalate, and sulfate, and aerial oxidation of ferric chloride vapor, at as low a temperature as possible. The products were crushed, ground, if necessary, and sieved with a 100-mesh Tylor screen prior to calcination, after which the specimens were dissolved in acid solution. The following is a detailed description of the preparation of the samples. Sample H. About 500 g of ferric chloride (guaranteed reagent) were dissolved in 5 liters of deionized water and filtered. Ferric hydroxide was precipitated by addition of the minimum amount of ammonium hydroxide solution, and the precipitate was washed continuously till chloride ion was not detected by silver nitrate solution, and then filtered. The filter cake was dried at 120°C for a week and ground, and the -100 mesh portion was used. Sample S. Ferric sulfate (guaranteed reagent) was pyrolytically decomposed in a crucible at 700°C for 24 hr and the product was sieved. In this case the following calcination was carried out at temperatures over 700°C. Sample B. Commercial ferric oxide (guaranteed reagent). About 15 kg of ferric nitrate were decomposed in a furnace maintained at 800°C for 2 hr. The actual temperature of the decomposition was not measured. The product was crushed and sieved, and the -100 mesh portion was used. Sample N. About 50 g of ferric nitrate (guaranteed reagent) were decomposed in a beaker in a sand bath until a red-brown dense solid was produced. This product was crushed and sieved, and subjected to complete decomposition at 500°C. The precalcined product was again sieved and used. Sample N2.5. Since the decomposition temperature was not controlled for sample AT, a different sample was prepared in a temperature-controlled furnace. The subscript represents the decomposition at 250°C. The product was treated in the same manner as sample N. Sample Nc. Under atmospheric pressure it is prac-tically inevitable that ferric nitrate hydrate melts to form a brown liquid at about 50°C before pyrolysis. For this reason, the salt was first slowly heated under reduced pressure (about 10-3 mm Hg measured in a trap refrigerated by dry ice-alcohol) to achieve dehydration without melting. About 5 hr were required for the dehydration and the partial decomposition. Then the temperature was elevated to 500° C in air for complete decomposition. The relatively porous product was sieved and used. Sample Ov. About 200 g of ferric oxalate hydrate (extra pure) were dehydrated under reduced pressure (as described above) followed by thermal decomposition at 500°C for 6 hr in air. The decomposition of this salt was accompanied by liberation of carbon monoxide, by which the ferric salt was initially reduced to a black powder. The powder changed in turn into brown ferric oxide as the gas liberation decreased and reoxidation predominated. The product consisted of sparkling fine particles passing through a 100-mesh screen. However it was ground and sieved as for the other samples. Sample D. Commercial fine powder for magnetic tape purposes. The preparation was as follows.5 Ferric chloride vapor and preheated excess air were mixed and passed into a reaction tube where oxidation took place at 450°C. The fine powder formed was collected in a cottrell chamber. The product was vacuum-degassed at 450°C for 1 hr and sieved.

Jan 1, 1969

By Thomas C. Atchison

An understanding of the physical processes involved in breaking rock with explosives will lead to better blasting techniques. In this chapter known rock breakage principles will be outlined, some conjectural ideas will be discussed, and areas needing further study will be pointed out. The principles outlined will serve as a basis for the design of blasting rounds described in the following chapter. 7.2-1. Factors Important to Rock Fragmentation. The efficacy of explosives as tools for rock fragmentation lies in their ability to deliver almost instantaneously large amounts of energy to a limited portion of the rock. When an explosive charge is detonated in a drill hole, its energy is released in a very small fraction of a second in the form of gas at extremely high pressure and temperature. The mechanics of the transfer of this energy to the rock and the resulting breakage are complex and not completely understood. Factors that have been identified as important to the fragmentation process may be grouped in three categories: explosive parameters, charge loading parameters, and rock parameters. EXPLOSIVE PARAMETERS. Explosive parameters known to influence breakage are density, detonation velocity, detonation impedance, detonation pressure, gas volume, and available energy. Detonation pressure is probably the best indicator of an explosive's ability to break solid hard rock. Detonation pressure is roughly proportional to the product of density and the square of the detonation velocity. The relative ability of different explosives to transmit their pressure to stress in a given rock is function of their detonation impedances. Detonation impedance is the product of density and detonation velocity. The volume of gas released in the explosive detonation undoubtedly is of importance, at least in the later stages of breakage, and is probably

Jan 1, 1968

By J. N. Hummel

The methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view. The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic. It is obvious that methods based on such a simple principle and capable of solving directly many of the practical problems of mining geology have found a widespread application. However, these methods are unable to furnish any information as to the presence, depth and physical properties of layers in the underground, which have different conductivities, but are parallel, or only slightly inclined, to the surface. Where such conditions exist in the underground, the picture of the field

Jan 1, 1932

By F. G. Miller

The washabilities of typical bituminous coals are discussed in an effort to illustrate the importance of determining, by a complete washability study, the sulfur forms and their distribution in a coal. This study will then show the extent to which the sulfur can be removed. It should be emphasized that each potential application requires a thorough study because of the varying amounts of sulfur in different coals. It is not the intent of this paper to show the best results that flotation can produce, but rather to illustrate the potential of this process and point out the importance of improved flotation techniques where sulfur reduction is involved. It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur make up almost all of the total sulfur content, occur in varying amounts in different coals, and can vary greatly in coal of the same seam. Pyritic sulfurs of 20% to 80% of the total sulfur have been reported. Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and ones' state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing

Jan 1, 1964

By K. E. Barrett

Exxon owns a uranium mill and holds two mining leases in Live Oak County, Texas, about halfway between San Antonio and Corpus Christi. The properties make up the Felder Uranium Operations which was reopened earlier this year. Exxon held an oil, gas, and other minerals lease on the J. C. Felder tract, which was adjacent to a relatively shallow uranium discovery by Susquehanna-Western, Inc. on the Marrs-McLean lease immediately south of the Felder property. Drilling in 1967 and 1968 confirmed the presence of reduced uranium mineralization in the basal sand unit of the Oakville formation on the Felder tract, which formed the major part of the roll-front deposit. In 1969 Exxon and Susquehanna-Western, Inc. entered into a sale and purchase agreement which provided for Susquehanna to mine and process Felder ore and purchase recovered uranium. Susquehanna moved an alkaline-leach mill from Wyoming, erected it on the Ray Point property, and placed it into operation late in 1970. Susquehanna mined and processed ore from the Felder and McLean properties through March 1973. Susquehanna ceased operations in March 1973. Exxon then acquired the mill and mill property. Exxon also purchased the mineral rights to the McLean lease, re-negotiated a mining lease for that property, and carried out shut-down programs for the mining and mill areas in the fall of 1973. The project was put on a standby basis until late 1973, when Exxon initiated mine feasibility studies for the project. MINE PLANNING EVALUATION The feasibility study for reopening the Felder Project began in late 1975 and was not completed until late 1976. I will discuss several areas of the feasibility study that required additional work prior to making the decision to renew operations. Ore Reserves Preparations for estimating the ore reserves began with the re-evaluation of more than 1500 natural radioactivity logs from exploration and pre-development drilling that had been completed on the property. These gamma ray logs of non-core rotary drill holes were the principal source of data used in making the estimate. Chemical assays of cores from the deposit were also used in the reserve determination. Electric resistivity and self-potential logs were made along with the gamma ray log. In December 1975 an additional core drilling project was undertaken to confirm the in-place density and radiometric equilibrium characteristics of the ore deposits. Comparison of chemical assays of cores with the U308 values calculated from the logs showed that the unoxidized ores were in radiometric equilibrium. In contrast, cores from anomalies occurring in near surface, weathered, and oxidized zones were in radiometric disequilibrium. Several important decisions were made in developing a mine plan or schedule of production from the Felder and McLean ore bodies. Disposal of Produced Mine Water: The ore bodies of the Felder Uranium Project occur at a point below the ground water table. The ore zones to be mined must first be dewatered to allow removal of mineralized material. In the open pit operations, this is accomplished by maintaining a perimeter ditch around the periphery of the open pit, allowing the interior of the pit to drain and collect into a sump and be pumped from the mine. In addition to anticipated water production from future mining operations, approximately 200M gallons of water was contained in three open pits left from prior mining operations. In two of these existing pits, the water was to be removed and disposed to allow for planned backfilling of waste material into these pits. The third pit would also have to be drained to allow continued mining of an area left from the prior operations. Essentially no ground water information was available for this area. The only data available was water production history from Susquehanna's mining operation. Two water wells were drilled early in 1976 on the Felder lease for use in obtaining hydrological data. A long term draw-down test was performed by pumping one water well and measuring water level drawdown in both the pumped well and the observation well. From these data, values for permeability and storage coefficient were calculated. These data were then used in modeling the aquifer to allow calculation of water influx into the mining area versus time. Once a schedule of water production, including the stored volume in the existing pits was calculated, alternate solutions for disposal were evaluated. The first system evaluated was a series of deep injection wells. The wells were designed to inject at a depth of approximately 3500 feet. Again very little information concerning reservoir characteristics of the receiving sand units was known. Using assumed values for reservoir permeability and storage coefficients, an injection well system was designed to allow for disposal of produced mine water. The biggest

Jan 1, 1979

By J. D. Price, W. M. Bertholf

One of the chief difficulties with which the operator of a coal washing plant has been forced to contend is the handling of the very fine coal. First he has the problem of separating the fine coal from washery water. This is usually accomplished by the use of settling cones or Dorr thickeners: in either event the separated fine coal contains a high amount (40 to 80 pct) of water and, somewhat loosely, dependent upon the size of the coal particles present, may be known as sludge or slurry. His second problem is the satisfactory further dewatering of such separated sludge and/or slurry. At the coal washing plant of the Colorado Fuel and Iron Corp., washed coal from the Deister Plat-O tables is sluiced to a stationary inclined de-watering screen provided with 3/16 by 1-in. slots, and the coarse coal passing over this screen is conveyed by a Baum-type elevator and a flight-type distributing conveyor to a battery of Carpenter centrifugal driers. The fine coal and water passing through the openings of the primary dewatering screens, plus the fine coal passing through the screens of the centrifugal driers (and no small portion of which is the result of the disintegrating action of these driers) is pumped to two 30-ft Link Belt settling cones. The sludge recovered as underflow from these cones was formerly dewatered on stationary screens having 1/16 by 1-in. slots and discharged on top of the coarse washed coal in the Baum drainage conveyor; but after a relatively few hours of op eration the circulating load of fine coal on this conveyor built up to a point where it became necessary to reduce the quantity of feed to the washing tables. The original arrangement of our coal washing and dewatering equipment is shown in Fig 1. In order to regain the loss in active throughput which had been caused by this circulating load, an installation of six vibrating filters was made during the year of 1936. This resulted in an increase in normal tonnage of washed coal from 1430 to 1750 tons per 8-hr shift, a gain of slightly over 22 pct. This increase in throughput has made a very substantial decrease in the " conversion cost" per ton of washed coal. Since the vibrators were installed, we have gained about 2,000,000 tons in production, compared to what would have been produced in the same number of shifts at the former rate. Putting it in slightly different form, we have saved in the past 12 yr the cost of 1400 operating shifts in the washery. Fig 2 shows the location of the vibrating filters as applied to the original flowsheet. It will be noted that the sludge from the bottom of the settling cones is passed through a distributing box and thence to the filters. The de-watered coal from the filters is de-livered to the conveyor receiving the dried coal from the Carpenter driers.

Jan 1, 1950

By R. E. Cech

Particles -3 to 30 µ diam of a 29.5 pet Ni, 70.5 pet Fe alloy after being melted and solidified while falling through a hydrogen atmosphere were found to contain a distortion-free body-centered-cubic phase. In most particles, the amount of body-centered-cubic phase approaches or equals 100 pet. It was shown by a series of experiments that this phase forms directly from the liquid. It is pointed out that a mechanism previously suggested in recent papers on the theory of the liquid-solid transformation can account for the solidification of body-centered-cubic phase in a temperature range where face-centered-cubic is the stable phase. IN the course of an operation to produce powders for a study of the martensitic transformation in Fe-Ni alloys, an unexpected phenomenon was observed. Powders of a 29.5 pet Ni alloy, which has a subzero M, temperature, were found to contain considerable amounts of a body-centered-cubic phase at room temperature. The experiments to be described were designed to elucidate the mode of formation of this unexpected phase. Experiments and Discussion An alloy containing 29.5 wt pet Ni, balance iron, was vacuum melted from high purity electrolytic iron and carbonyl nickel shot and solidified in the crucible. The metal was converted to oxide, ground to 100 pet <37µ, pressed to a cake, and homogenized 20 hr at 1350°C. To insure homogeneity the grinding, pressing, and homogenizing heat treatment was repeated a second time. The oxide was then ground to 100 pct <37µ and hydrogen reduced at 500°C. The reduced powder was given a spheroidizing treatment to produce spherical cast particles. The treatment consisted of dispersing the particles in hydrogen and allowing them to drop through a vertical hydrogen furnace set to a temperature higher than the liquidus of the alloy. This operation, commonly known as shotting, has been described more fully elsewhere.&apos; The powder produced by this method was found to contain approximately equal parts of body-centered-cubic and face-centered-cubic phases. A magnetic separation technique, previously described,&apos; was applied, and it was found that particles were either completely face-centered-cubic or nearly completely body-centered-cubic. The microstruc-

Jan 1, 1957

By Charles V. Seastone

The hydro-electric plant of the Peninsular Power Co. is located at what is commonly known as Lower Twin Falls on the Menominee River. This location is about 3I/2 miles north of the city of Iron Mountain, Mich. The principal points of delivery of electric energy from this plant are in the mining regions adjacent to Florence, Wis., and Iron River, Mich., and in the cities of Iron River and Iron Mountain. The hydro-electric plant at Twin Falls and the substation of the Iron Mountain Electric Light & Power Co, are connected by a 6,600-volt transmission line carried on steel towers and steel poles, the latter being used within the city limits. The plant at Twin Falls and the substation at Iron River, about 36 miles distant, are connected by a 66,000-volt, duplicate, three-phase transmission line, supported on steel towers. At Iron River, are located a 1,500-kw. auxiliary steam plant, and the substation, from which the current is distributed to the mines in this vicinity. A description of the auxiliary plant, main and customers&apos; substations, and of the main and secondary transmission lines, follows later in this paper. General Layout The relative location of the dam, forebay, and power house will be understood by referring to Fig. 1. The dam is constructed on a ledge of solid rock which forms Lower Twin Falls. This rock ledge offers an excellent location in that the height of the dam, and therefore the amount of concrete, are thereby reduced, and also in that practically no pumping was required in unwatering the dam site. The maximum head provided by the dam is 44 ft., with an average working head of from 40 to 42 ft. The other structures, including the substructure of the power house,

Jan 1, 1915