Search Documents

By John W. Padan, Thomas E. Howard

Most of what has been written during the past few years on marine mineral resources has emphasized the vast potential of the ocean, and its floor, as a source of the vital mineral raw materials upon which our modern technological society depends. Computations have been made to demonstrate that the sea contains sufficient minerals to support any reasonable world population indefinitely. The importance of these resources from the standpoint of strengthening the national mineral resource base has been pointed out. And though the information upon which these conclusions are based is sketchy, essentially qualitative, and often conflicting, there can be no doubt that the mineral potential of the sea is tremendous and that there are compelling reasons for working toward its exploitation. Unfortunately, there has been little emphasis on the problems that must be overcome, from the perspective of the economics of mineral production. Some of these problems have been noted, and some authors have appraised them realistically. However, many proposed solutions have been more romantic than practical, from the standpoint of both technology and economics. As a result the general impression has been given, particularly to those uninitiated in the realities of mineral production, that the mineral wealth of the sea is there for the taking-requiring only a good modicum of courage and technologic innovation to place it within easy grasp. But developing the capability necessary for substantial, profitable production of sea bottom minerals will be far from easy. It will be accomplished much more quickly if the problems are faced squarely, defined properly, and attacked in an orderly, logical sequence. While this approach may lack glamour, it offers the highest probability for success.

Jan 6, 1966

By Isobel Clark

The increasing complexity of modern mining technology makes it ever more difficult to decide on the 'best* way to solve problems in mine planning. Yet with escalating costs it becomes increasingly more important for the mining engineer to be able to evaluate quantitatively the implications of the 'what happens if' postulation on the efficiency and economics of exploitation. The use of a model of the orebody can yield an estimate, not just of overall expected results, but also of the sensitivity of these results to possible variations in the orebody. Estimation techniques, such as Kriging, will produce the expected value for the grade of ore at any given point, or over any given volume within a deposit. However, the actual grades mined during production will - of necessity - differ from the predicted values. These possible variations, and the sensitivity of the management decisions to them, can be investigated in detail by the use of simulation. An orebody can be simulated which follows the known characteristics of the deposit at any given stage in development. These properties might be the histogram of grade values, the semivariogram from the samples, the actual borehole assays, geological constraints and/or interpretation, topography, lease boundaries etc. This would be one possible 'realisation' of the deposit as dictated by the currently known data. If several of these simulations are carried out, each conditioned to the current knowledge of the orebody, then it is possible to gain an idea of the range of possible outcomes of any mining procedure or decision taken - all of which are equally likely. Not only can the best decision then be taken, but its sensitivity to the inherent variation within the orebody, and to the ever present estimation errors may be thoroughly studied.

Jan 1, 1977

IN THE early evening of October 15, 1954, a large specially designed truck, convoyed by a second smaller one, arrived at Silver Bell, Arizona, completing a ten-hour 110-mile journey from Phoenix. The big truck was driven through gaps left in a previously prepared concrete foundation, the load was jacked up, the large girders that constituted the bed of the truck were pulled away, and the load was then lowered into place on the foundation. A crew of two men, the two truck drivers, finished the job in a little more than an hour. When they were through, a complete and attractive three-bedroom house, prefabricated in Phoenix, was almost ready for occupancy. About all that remained to do was to connect the utilities-water, electricity, plumbing, and gas. The kitchen and bathroom equipment and appointments were superior in every respect, and there was a built-in car port for the automobile of the prospective residents. This family domicile was one of more than one hundred, each averaging about $8,000 in cost, that the American Smelting and Refining Company has provided for its employees engaged in mining and milling 7,500 tons per day of low-grade Porphyry copper ore. Aside from the fact that it is more economical-partly because of the variety of union craftsmen needed to build and equip a house-to do the work in a city 110 miles away, the significant point is the high quality of housing that is provided for what may be called in nostalgic vein the "mining camp" of 1955. Silver Bell is typical of all the Porphyries in this respect though the community is relatively small. At San Manuel

Jan 1, 1957

By R. S. Goodrich, G. S. Ansell

The microstructure of three Al-Al2O3 SAP-Type alloys (containing 2.0, 3.0, and 5.7 wt pct alumina, respectively) was studied utilizing transmission electron microscopy. These alloys were fabricated from aluminum powders by powder-metallurgical techniques, cold-rolled into thin strips, and recrys -tallized. Thin foils suitable for an electron-transmission study were then prepared from the strip material by electropolishing. The microstructure of these alloys is shown to consist of small (0.1 mean diameter) plate -shaped alumina particles finely distributed in an aluminum matrix. In the higher-oxide content alloys the platelets are somewhat larger and more irregular in shape. The distribution of oxide particles is not uniform and there is an increasing tendency toward clumping SINCE the discovery by Irmann1 that aluminum alloys produced by compacting, hot pressing, and extruding fine aluminum powders possess remarkable high-temperature mechanical properties, the Al-A12O3 SAP-Type alloys have been utilized extensively as model dispersion-strengthened alloys in both experimental and theoretical invest igations.2-8 The use of the SAP-Type alloys as model dispersion-strengthened alloys implicitly assumes that their microstructure has been completely delineated. This is, however, not the case. with increasing oxide content. In all the alloys studied, the mean center-to-center spacing of particles was quite small (0.2 u) due to the very fine oxide debris present. Selected-area diffraction of the specimen identified the oxide as either y Al2O3 or y' Al2o3. The re crystallized MD-5100 alloy exhibited a mean grain diameter of only 0.7u, while the grain size of the other alloys was several hundred microns. Severe pinning of the grain boundaries by oxide particles was rarely observed, and the grain boundary triple points in the small-grained MD-5100 alloy were often particle -free. Diffraction contrasts visible around the particles are attributed to elastic strain fields set up by differential thermal contraction during cooling from the recrystallization anneal. Early investigation demonstrated that optical metallography did not possess sufficient resolution to observe the microstructure of the SAP-Type alloys.' Later, extensive use was made of replication techniques to study the microstructure by means of electron microscopy.7-9 These studies indicated that the SAP-Type alloys consist of a dispertion of irregular Al2O3 platelets, approximately 150A thick 9 and a micron or so on edge,9 distributed in a matrix of commercial-purity aluminum. These oxide platelets tend to be oriented in the aluminum matrix, with their largest dimension parallel to the extrusion direction. 8,9 A study employing polarized-light techniques1' indicated that the grain size of a series of as-extruded SAP-Type alloys was several microns in diameter, while the grain size after re-crystallization was several millimeters in diameter. A more recent study 12 utilizing surface-replication techniques examined the particle morphology,

Jan 1, 1964

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By JESSE L. MAURY

DEVELOPMENT of new gold mines in Canada since the price of that metal was increased in 1932 and 1933 has been of interest and importance to many of us. The day-by-day story has given an impression of aggressive effort and enough good luck so that the spirit of enterprise has been encouraged. It is the purpose of this article to report the results of a statistical appraisal which give emphatic numerical confirmation to this impression, together with certain side lights on the costs of development and equipment of new mines. The data presented have been taken from all readily available published sources up to the close of 1938 and are representative of that year. A. B. Bower did a large part .of the spadework and Weston Thomas offered many helpful suggestions.

Jan 1, 1939

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By Kenneth B. Ray, George R. Gardner

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent, investigation developed similar processes, which were successfully used in

Jan 1, 1939

By George R. Gardner, Kenneth B. Ray

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent, investigation developed similar processes, which were successfully used in

Jan 1, 1939

By Laurence Hicks

CONSIDERATION of the past work on the subject of the diffusion of chromium into iron suggested that additional information might be given by the use of X-ray spectroscopy in following the concentration changes through the diffusion zone. Grübe and Fleischbein1 packed rods of electrolytic iron in a mixture of alumina and chromium. These specimens were heated in an atmos-phere of purified hydrogen for varying lengths of time. After treatment the specimens were examined metallographically and showed the usual structure, consisting of a border of radially oriented columnar grains ending in a sharp boundary line. Reference is made to the fact that etching with certain reagents will attack only the material inside the border of columnar growth and also to the fact that polishing seems to develop a ridge at the position of the boundary between the etched and unetched areas. By chemical analysis of thin layers turned off on a precision lathe, the authors were able to obtain depth-concentration curves. These curves, reproduced in Fig. 1, show that 'in most cases a pronounced change of slope occurs, corresponding to the position of the boundary of the columnar grains. In a later paper Grübe extends his work to other systems which show the same characteristics.2 He concludes that the reason for the break in the curve is that a hindrance of diffusion occurs at the place where the regularly oriented grains of the diffusion zone meet the random grains of the interior portion, on the assumption that the diffusion velocity in one direction in a grain may be greater than in another direction, and that the grains in the diffusion zone orient themselves so as to give the maximum diffusion rate. Kelley3 points out that Grübe has failed to note that the boundary line does not consistently cross all grains and

Jan 1, 1933

By L. W. Kempf, R. S. Archer

The binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.' Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application. Constitution of Alloys Magnesium and silicon combine in aluminum alloys as the compound Mg2Si, which forms a binary system with aluminum. In alloys containing an excess of silicon over that required to form the compound, solidification ends with the freezing at 1022' F. (550' C.) of a ternary eutectic of aluminum, Mg²Si, and silicon. Judging from the horizontal projection of the liquidus surface as given by Hanson and Gayler,² this ternary eut,ectic contains about 13 per cent. silicon and 6 per cent. magnesium. All of the alloys discussed here contain excess silicon, so it

Jan 1, 1931

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,' the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".'7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.'* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.' Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952

By L. Weyher, H. L. Lovell

This discussion is restricted to a very specific application of the cyclone - its use as a hydro-cyclone in the cleaning of fine coal. It is hoped that the development of the present data will assist in the further elucidation of existing qualitative models, and also in an enhanced application of the hydrocyclone and provide a base for further research. Discussed are the mechanisms of gravity separation in hydro-cyclones, test procedures, experimental observations, and industrial applications from these studies. Within the general area of unit operations, a considerable effort has been expended in theoretical and empirical research associated with cyclone operations. The motivation involves the industrial requirement for devices and techniques to manipulate small particles at low operating costs, a situation required in coal preparation. There are good reasons why the cyclone helps to satisfy this demand, because it combines operational simplicity (no moving parts) with versatility and high throughput capacity per unit area. The cyclone is one of the most widely applied tools in the process technologies. There are areas for potential cyclone application which have been only meagerly explored or not considered at all. This discussion is restricted to a very specific application of the cyclone - its use as a hydrocyclone in the cleaning of fine coal. It represents an initial presentation of a more comprehensive report. Coal preparation can appropriately claim the hydrocyclone since most of its predominant industrial uses have originated in this area and have spread into other applications, including the broad field of ore dressing, the petroleum industry, chemical processing, nuclear engineering and food technology. There is one operational principle common in all cyclones: A fluid is tangentially introduced into a cylindrical or conical container under pressure. A predominantly irrotational flow field1 is established within the cyclone (Fig. 1). The uniqueness of this flow is indicated by the variation in tangential velocity across the cyclone radius, which reaches a maximum a short distance from the center and decays toward the cyclone wall. In contrast, the tangential velocity in a centrifuge increases uniformly toward the wall. Usually two products are discharged from the cyclone. They differ in that one discharge consists predominantly of that portion of the feed fluid which moves along the wall axially away from the feed inlet, while the other consists predominantly of fluid spiralling along the central regions of the cyclone, in an axial direction opposite to that of the wall current. Fig. 2 indicates these discharge points schematically. The latter product may be termed the vortex-product, since it is discharged with the central vortex-current. In the case of conical cyclones, the former product may be referred to as the apex-product. Although the names "over- and underflow" are widely used, many cyclones are operated from extreme angular positions thus the proposed terms are less ambiguous. The cyclone feed fluid can be laden with solid particles or nonmiscible fluid drops. Such a feed component is discharged from the cyclone, after some residence time, into the one or the other product. Yet, the orifice through which a particle will leave the cyclone is dependent upon a number of factors. These factors, in a statistical sense, determine the path of the particle within the cyclone. Thus, different separation phenomena are possible and different process results attainable by the controllable variation of the particle path. It is then, to attain a fuller understanding of this particle path, to which this study is ultimately directed. It is anticipated that the detailed study of the data being developed will allow further elucidation of existing qualitative models. However, the development of a quantitative description of cyclone operation in terms of a mechanism is not currently feasible. The flow conditions in a cyclone are not fully understood even for a pure fluid, without the added complexity of the inclusion of multiple size-density particles. It is hoped that the development of the present data will also assist in an enhanced application of the hydro-cyclone and provide a base for further research. Some practical applications drawn from the data are suggested. Cyclone operations have been classified according

Jan 1, 1967

By A. D. Brokaw

The so-called "paraffin dirt" of the Gulf Coast oil fields has been considered an indication of the possible presence of oil and gas, and not a few wells have been brought in solely on the basis of such evidence. In a sense, it may be empirically justified as evidence of the presence of oil or gas, though it cannot be said to be infallible. If the writer is correctly informed, its association with oil and gas was pointed out by Lee Hager some years ago, and while it is commonly mentioned by geologists and operators in conversation, no discussion seems to have found its way into print. The present interpretation is based on laboratory study rather than on field investigation, and is put forth with the hope of stimulating discussion which shall lead to more complete understanding. The term "paraffin dirt" has been applied to soils with a peculiar texture, which has been described as "curdy" or "rubbery." When moist, the material breaks much after the fashion of "green" cheese. It is rubbery under compression, but does not resemble rubber in tenacity or cohesion. When dry, the material ranges from hard clods to a horny mass of high tensile strength. The shrinkage in drying is very great, especially in the hornlike matter. The moist material ranges in color from dark brown in the specimens rich in organic matter to grayish in specimens containing more inorganic matter. All of the specimens studied were readily attacked by molds, which in some cases grew in great profusion on the samples. Samples exhibited a rather characteristic "swampy" or "mucky" odor when wet, and a characteristic odor of humic soils when moist. If the material is brought into suspension in water, very fine sand settles out and may be recovered by successive washing and decantation. The sand is almost entirely quartz, but contains occasional fragments of feldspar—more or less kaolinized and iron-stained. Practically all of the sand passes through a 100-mesh screen and the grains are extremely sharp —possibly below the limit of rounding. A flocculent mud, of clay and organic matter, remains in suspension for days. Some material is taken into solution in the water, imparting a slight tendency to froth when vigorously shaken. The results of partial analyses of four samples of "paraffin dirt," and, for comparison, one of a coastal plain soil are given in Table I.

Jan 1, 1920

By W. H. Emmons

The exploration of deposits of the metals will never become an exact science. There will always be an element of uncertainty in prospecting and developing mines. In countries where the surface has been closely scrutinized, most of the deposits whose outcrops contain valuable metals have probably been discovered. Many metalliferous deposits, however, are normally so much altered at the surface that the true significance of their outcrops is likely to be obscured. If a deposit is not exposed, its presence may become known by some one of its characteristics that is different in kind or in degree from a similar feature of the associated rock. Thus, a deposit that is not exposed may be discovered because of its magnetic property. So few minerals are strongly magnetic that the value of magnetic surveys is limited, but the dip needle has nevertheless proved of great aid in locating magnetic belts, and these in some regions are associated with workable iron ores. The Cuyuna Iron Range of Minnesota, which does not exhibit any outcrop of iron ore, was discovered by drilling "areas of attraction" that are due to belts of magnetic rocks associated with the iron ores. In some regions the use of the dip needle is justified, even if it does no more than reveal the strike of the rocks, since a knowledge of the latter enables the driller to locate and point his holes to advantage. The measures of gravity by the use of the pendulum are so accurate, or the limit of error is so small, that one might detect the presence of a concealed tabular deposit approximately at the surface, 34 ft. (10.36 m.) thick, having a density double that of the surrounding rocks. However, not many deposits have a density twice that of ordinary rocks and a thickness as great as 34 ft.; if they lie a short distance below the surface the density or the thickness must be even greater. Consequently, there is not much hope of sufficiently developing the gravity method of detecting deposits of heavy ores to make it of practical value. If the limit of error could be reduced to about one-tenth the present factor, and if the rather tedious and painstaking methods of determining gravity that are now in use could be simplified, the method would promise some degree

Jan 1, 1918

By D. F. Stein

In spite of the apparent usefulness of autoradiography in demonstrating segregation, it has had very limited success in demonstrating grain boundary segregation. Because of this limited success, a model system amenable to mathematical analysis was devised to determine which variables in the experiment are most important. As a result of these calculations, it was concluded that autoradiograPhy is a rather insensitive technique to measure grain boundary segregation. The range (energies) of the emitted particles (ß and a) must be low, and the concentration of the radioactive speczes at the grain boundary must be (in general) two or three orders of magnitude greater than the concentration within the grain. Because of these very restricted conditions , the limited success of the technzque is not surprising. In spite of the apparent usefulness of autoradiography in demonstrating segregation, it has had very limited success in demonstrating grain boundary segregation. Sulfur segregation in iron1 and possibly polonium segregation in Pb-5 pct B1 2 alloys are the only autoradi-ography experiments that have demonstrated segregation to grain boundaries in metals without the formation of a second phase. Segregation to a boundary without the formation of a second phase is often called Gibbs' absorption and is discussed by McLean in Chapter 5 of Ref. 10. There are several394 experiments showing grain boundary diffusion of a radioisotope, but this type experiment is not representative of equilibrium between the concentration of an element at a grain boundary and that in bulk, so it will not be discussed in this paper. In an attempt to determine if temper embrittle ment of low-alloy steels was associated with segregation of antimony to grain boundaries, a program to use auto-radiography (using Sb-125) was initiated. Even though other measurements strongly suggest that segregation is occurring during embrittlement, no evidence of grain boundary segregation was observed in the auto-radiography experiments. An attempt was also made to detect segregation of carbon (using C-14) to grain boundaries in iron during slow cooling. There is again strong indirect evidence7 that segregation occurs during such a treatment, but the autoradiography experiment gave no evidence of such segregation. Because of the failure of these experiments and the general lack of success by our metallographic unit in measuring grain boundary segregation using autoradi-ography, a model system amenable to mathematical analysis was devised to determine which variables in the experiment are most important. MODEL SYSTEM The model system is illustrated in Figs. 1 and 2. It is a semi-infinite bicrystal with a single grain boundary perpendicular to the top face. The width of the grain boundary, W, is defined as the region to which segregation has occurred and it is assumed that this region is of constant composition. The assumption of an infinite dimension is for mathematical reasons but the results of such an analysis (as will be demonstrated later) are valid for even very small specimens. It also is assumed that the measurement is not limited by means of detecting the radiation (photographic emulsions, counters, and so forth) but that the means of detecting radiation is linearly sensitive to the radiation and has infinite resolving power. The distance y is the perpendicular distance from the center of the grain boundary to the point at which the background radiation is measured and x is the integration variable. CALCULATION FOR BETA PARTICLES Two values of the intensity of radiation will be calculated, the intensity at the center of the grain boundary and the intensity far from the grain boundary. The radiation at the center of the grain boundary can be calculated in the following way. Assume a grain boundary of width W having a uniform concentration equal to Cgb + Cb where CGb is the excess concentration of the element under consideration at the grain boundary and Cb is the bulk concentration. The intensity of radiation, IgB, at the center of the grain boundary, is a consequence of the amount of radioactive material, decay rate, absorption, and geometrical factors which can be represented mathematically by the following expression:

Jan 1, 1968

REJUVENATED is an apt word to apply to Chino, Kennecott's big open-pit mine at Santa Rita, New Mexico. Back in 1923 Chino was merged with Ray by an exchange of shares, and in 1926 the Ray-Chino combination was taken over by Nevada Consolidated through an issue of bonds that were traded for the Ray and Chino assets. Subsequently, of course, the whole package was acquired by the Kennecott Copper Corporation. On the basis of the terms of the Ray-Chino-Nevada exchanges, Chino was rated third in value, something less than thirty per cent of the total. In 1955 the appraisal would doubtless be forty per cent or more. But it is not only vis-a-vis Ray and Nevada that Chino has blossomed out. At the end of 1931, Chino ranked seventh among the Porphyries in point of output; whereas by the end of 1954 it was fifth,. having passed both Inspiration and Nevada Consolidated. Sharp curtailment in production in 1932-33-34 and total suspension in the two years following (see Fig. 21) found the property in a somewhat parlous position. However, the engineers had not been idle; they had been planning for the future, and in 1937 a far-reaching program of rejuvenation was launched. During the ensuing five years, capital expenditures totaled more than $8,500,000. Among the projects undertaken were the following: (1) Mine-Purchase of larger and better equipment for drilling, loading, and transporting the ore. (2) Mine-Beginning of the first systematic project to leach and recover copper in the waste dumps at the mine.

Jan 1, 1957

By A. W. Schlechten, Ernest J. Breton Jr.

Experiments on the separation of copper and zinc ions by selective action of ion exchange resins showed the carboxylic type to be more effective than the sulphonic resins. The latter demonstrated a greater capacity over a wider pH range. Data show the effectiveness of resins as a means of concentration. IN recent years the restrictions of stream pollution laws and the high price of metals have created an interest in ion exchange as a means for metal recovery. Some applications have proved successful. In Germany during World War 11, 17 tons of copper per day were recovered from rayon mill wastes by means of ion exchange resins;' and for some time in this country a large ion exchange unit has been in operation for the recovery of copper from rayon waste water. The possibilities of applying ion exchange to the recovery of metals occurring in plating rinse water is particularly promising. In most of these applications only the metal being recovered occurs in the waste. The ion exchange resins act merely as a means of concentrating the metals to a point where they can be recirculated. It would be highly desirable to use ion exchange as a means of not only concentrating but also of separating metals. With the exception of the impressive separations accomplished in connection with the atomic energy program, very little has been done on metal separations.' Therefore, an investigation was undertaken at the Missouri School of Mines and Metallurgy to determine if either of the two main types of ion exchange resins could be used to separate metal ions in solution. The selective removal of copper ions from a mixture of copper and zinc on carboxylic and sulphonic-type resins was investigated as a function of flow rate, pH, copper-zinc ratio, and concentration. It was shown that zinc can be separated from copper and that very large ratios of concentration can be obtained using ion exchange resins. Since ion exchange is relatively new to the field of metallurgy, a brief review of the subject will be included. Theory of Ion Exchange A comprehensive theory for ion exchange has not been developed as yet, but the mechanisms are analogous to metathetical reactions: R Na + Cu++ *=? K(SO3)2 Cu + 2Na+ R is the designation for the ion exchange resin. If a copper solution is passed over a resin bed in the sodium form, two ions of sodium will be released for every ion of copper removed. For the most part this reaction follows the laws of mass action and of electrical neutrality. Consequently, if an excess of sodium ions is passed over a bed containing copper, the reactions will be reversed, and the resin will be regenerated to its original form. A few empirical rules governing the exchange reaction have been set forth: 1—In general ions with a high valence will replace ions with a lower valence. 2—Ions having higher activity coefficients have a higher replacement potential. 3—In a series of mono-valent ions, those with the smallest radii of hydra-tion will tend to replace those having larger radii of hydration. 4—Where ions are similar in most respects, those with the higher atomic weight sometimes will take precedence. This last rule is not as definite as some of the others. These rules apply to rather dilute solutions at moderate temperatures and assume all ions to be present in about equal concentrations. Higher concentrations and temperatures may in some cases reverse the normal exchange reactions. Ion exchange materials are unique in that their efficiency increases as the concentration of the solution decreases. For many exchangers, most efficient operation is obtained at concentrations in the order of one thousandths of a percent. Most applications, though, are made in solutions containing considerably higher concentrations than this. Coste9 as shown that ion exchange resins will remove aluminum and iron effectively' from solutions of up to 10 pct chromic acid. Ion Exchange Resins Ion exchange resins are insoluble, porous, resinous structures to which active groups have been attached. Active groups such as (—SO,,)- and (COO)- pick up cations; hence structures saturated with groups such as these are called cation exchangers. Structures saturated with groups such as (—NH,)' which pick up anions, are referred to as anion exchangers. The resinous structure of necessity is resistant to strong acids, bases, oxidizing, and reducing agents, and most of the common organic solvents. An idea of the stability can be gaged from the fact that resins last for many years under constant use without detectable chemical or physical breakdown. The ion exchange reaction is not confined to the surface of these synthetic resins. Its porous structure permits active groups in the center of a particle as well as those on the surface to remove ions. A high capacity resin such as Amberlite IR-120 will remove up to 3.3 lb Cu per cu ft of resin. In this investigation several approaches to the problem of separating copper from zinc by ion exchange were considered. First, if a reagent could be found which would complex one of these metals and not the other, then by passing this reagent through a bed of exchanger containing copper and zinc, the

Jan 1, 1952